Atom OD /19.5 User Manual

Transcription

1 Atom OD /19.5 User Manual August 2018 Version 1.4

2 About This Document This document is intended installers and users of the Baicells Atom OD04/06-14 or Atom OD04/ outdoor user equipment (UE). The information covers how to install, set up, and use the outdoor UEs for broadband wireless access to Long-Term Evolution (LTE) carrier networks. Copyright Notice Baicells Technologies, Inc., copyrights the information in this document. No part of this document may be reproduced in any form or means without the prior written consent of Baicells Technologies, Inc. Disclaimer The information in this document is subject to change at any time without notice. For more information, please consult with a Baicells technical engineer or the support team. Refer to the Contact Us section below. Revision Record Date Version Description SMEs/Contributors Writer/Editor 27-Aug-2018 V1.4 Updated GUI screen shots based on BaiCPE_V100R001C01 B005SPC009 and BaiCE_AP_2.1.4_NA 21-Feb-2018 V1.3 Updated for CAT 6 Cameron Kilton Rick Harnish Dec 2017 V1.1, V1.2 Draft Yang Yanan Cameron Kilton Rick Harnish Sharon Redfoot Sharon Redfoot Sharon Redfoot 2

3 Contact Us Baicells Technologies Co., Ltd. China Address: 3F, Bldg. A, No. 1 Kai Tuo Rd, Haidian Dist, Beijing, China North America Address: 555 Republic Dr., #200, Plano, TX 75074, USA Phone: Phone: contact@baicells.com Website: sales_na@baicells.com or support_na@baicells.com Website: 3

4 Table of Contents 1 Introduction Parts & Materials Description Installation Procedures Basic Configuration Log in and Change the Password Configure Network Mode Configure LTE Connection Method Configure Scan Method Configure APN Management Appendix A: Technical Specifications Basic Specifications RF Specifications Wi-Fi Specifications Software Specifications Environmental Specifications Global Part Numbers Appendix B: Technical Specifications Basic Specifications RF Specifications Wi-Fi Specifications Software Specifications Environmental Specifications Global Part Numbers Appendix C: CE Statement Appendix D: FAQs List of Figures Figure 1-1: Baicells Broadband Wireless Access System... 6 Figure 3-1: Atom OD04/ Figure 3-2: Atom OD04/ Figure 3-3: LEDs and Interfaces Figure 4-1: Atom OD04/06-14/19.5 Installation Figure 4-2: Anti-Slip Rubber Figure 4-3: Bracket Figure 4-4: Install Unit on Bracket Figure 4-5: Tighten Bracket Figure 4-6: Threaded Rod Figure 4-7: Attach Omegas

5 Figure 4-8: Remove Bracket Figure 4-9: Fix Bracket to Wall Figure 4-10: Install Unit Figure 4-11: Mark Drilling Locations Figure 4-12: Install Bracket Figure 4-13: OD04/ Grounding Figure 5-1: Login Figure 5-2: Main Menu Figure 5-3: Change Password Figure 5-4: Network Mode Figure 5-5: Connection Method Figure 5-6: Scan Method Figure 5-7: Frequency Lock Figure 5-8: PCI Lock Figure 5-9: APN Management List of Tables Table 2-1: Parts... 8 Table 2-2: Materials... 9 Table 3-1: LEDs Table 3-2: Interfaces Table 5-1: APN Management Settings

6 1 Introduction The Baicells Atom OD04/06-14 and OD04/ outdoor user equipment (UE) is part of the Baicells broadband wireless access system that integrates with carrier networks based on Long-Term Evolution (LTE) technology. The Baicells system allows telecom operators, service providers, and enterprises to bring broadband data and voice services to customers or employees, even in challenging environments such as rural locations. The outdoor UE serves as a gateway between the user s computers or other smart devices and the carrier network by communicating wirelessly with the service provider s LTE enodeb s (enb) at cell sites located in the region (Figure 1-1). The enbs communicate with the carrier network, providing the user with internet access. The user-friendly, plug-and-play design behind the Atom UE makes it quick and easy to install, configure, and use. And because it is carrier-grade equipment, the UE is built for endurance and the ability to adapt newer LTE technologies as they evolve. Figure 1-1: Baicells Broadband Wireless Access System Note: The terms user equipment (UE) and customer premise equipment (CPE) are used interchangeably in the GUIs and documentation. Likewise, the terms enodeb (enb) and base station are used interchangeably. 6

7 Following is a list of the key features of the Atom OD04/06-14 and OD04/ UEs. Exact specifications vary by model: (Refer to the technical specifications in Appendix A for Atom OD04/06-14 and Appendix B for Atom OD04/ ) Support standard LTE FDD and TDD bands and comply with 3GPP Release 9 CAT4 or Release CAT 6/7 standards o FDD: Band 7 o TDD: Bands 38, 40, 41, 42, 43, 48, and customized Ethernet interface: o o OD04: 100 Mbps OD06: 1000 Mbps Local and Web based GUI, TR069 network management protocol, Baicells Operations Management Console (OMC) Integrated bipolar directional high-gain LTE antenna Cell lock, SIM lock, and Pin lock User-friendly LEDs Power supply using Power Over Ethernet (PoE) Pole or wall mount options Wi-Fi assisted alignment 7

8 2 Parts & Materials Refer to Table 2-1 for a list of the components that you should receive with the Baicells Atom OD04/06-14 or OD04/ user equipment (UE). Table 2-1: Parts Item Qty Picture Atom OD04/06-14 or Atom OD04/ unit 1 Power Cable 1 PoE Power Adaptor 1 Atom OD04/ Mounting Bracket 1 each User Manual 1-8

9 You will need standard tools, Ethernet cable, and RJ-45 connectors to cable the outdoor unit to the indoor LAN equipment. The cable length will depend on where the UE will be placed externally. Refer to Table 2-2. Table 2-2: Materials Item Ethernet Cable Description Outdoor shield CAT5E Shorter than 330 feet Ground Wire 16mm 2 yellow-green wire 9

10 3 Description The Baicells Atom OD04/06-14 and OD04/ models of user equipment (UE) are powerful, outdoor, standards-based devices designed to connect seamlessly to any standard Long-Term Evolution (LTE) enodeb (enb) operating on the same frequency band. The devices have a small, sleek form factor (Figures 3-1 and 3-2), yet are ruggedized for the most challenging outdoor environments. Refer to Appendix A for the technical specifications. Figure 3-1: Atom OD04/06-14 Figure 3-2: Atom OD04/

11 Looking further at the unit (Figure 3-3) you will see LED indicators on the side and interfaces on the side, back, and bottom of the unit. The LEDs are explained in Table 3-1, and the interfaces are described in Table 3-2. Figure 3-3: LEDs and Interfaces 11

12 Table 3-1: LEDs LEDs vary by model not all models will have all of the LEDs listed below. Identity Description Color Status Description MIU - Yellow LTE SIM LAN LTE network status indicator Universal Subscriber Identification Module (USIM) card status indicator 100 or 1000 Mbps Local Area Network Ethernet indicator Blue Yellow Yellow PWR Power indicator Yellow LTE Signal 1, 2, 3, 4, or 5 bars to indicate connection status and signal strength. The more bars, the stronger the signal between the CPE and a network cell. Green Off Steady On Blinking Off Steady On Steady On Blinking Off Steady On Blinking Off Steady On All Off Steady On Blinking Reserved. Reserved. Reserved. The unit is not connected to the LTE network. The unit is connected to the LTE network. The USIM card is functioning normally. The USIM card is not inserted or is not functioning normally. No Ethernet connection established Ethernet connection is normal Data is transmitting No power supply to the unit Power to the unit is on The signal is too weak for the unit to connect to the LTE network. Bars will light steadily according to signal strength The unit is scanning the LTE network. The unit is authenticating with the network. The unit is getting an IP address from the LTE network. Table 3-2: Interfaces Interfaces vary by model not all models will have all of the interfaces listed below. Interfaces PoE TF or SD Slot SIM/USIM Slot RESET GND Description The Power over Ethernet (PoE) power adaptor is connected to the unit. Card slot for a secure digital (SD) card Universal Subscriber Identity Module card slot, 1.8V/3.0V USIM 2FF Press the reset button for at least 10 seconds to restore the UE to its factory settings. Ground lug. The unit is connected to Earth by conductor. 12

13 4 Installation Procedures Follow the steps below to install the Atom OD04/06-14 or OD04/ user equipment (UE). 1. Prepare the Ethernet cable, per section 2 Parts & Materials. The Ethernet cable will run from the outside Atom unit to the inside of the facility, where the unit connects to the LAN. Cable length will vary by location. 2. Loosen the screws on the Atom s waterproof cover, and open the cover. 3. Connect the Ethernet cable to the PoE port on the unit. Connect the other end to the power adaptor. Refer to Figure Follow the instructions on the SIM/USIM card to insert it in the Atom unit. Attention: Do not power on the unit while installing or uninstalling the SIM/USIM card. Doing so could damage the card and the unit. 5. Close the Atom unit s waterproof cover, and tighten the screws. 6. Atom OD04/06-14: Connect the ground cable to the ground screw. (NOTE: The Atom OD04/ grounding information is covered in step 11.) 7. Plug the power adaptor into an electrical outlet. Pay attention to the power adaptor interface directions noted on the adaptor itself. The LED indicators should light up. Figure 4-1: Atom OD04/06-14/19.5 Installation 13

14 8. Mount the Atom unit. If you are installing the unit on a pole, e.g., to attach to a roof, follow the instructions provided in step 9. If you are installing the unit on an outside wall, follow the instructions provided in step Pole installation: a. Atom OD04/06-14: a1) Round an anti-slip rubber band on the pole (Figure 4-2). Figure 4-2: Anti-Slip Rubber a2) Fix the bracket over the band using the hoop (Figure 4-3). Figure 4-3: Bracket a3) Install the unit on the bracket, and tighten the screw (Figure 4-4). Figure 4-4: Install Unit on Bracket b. Atom OD04/ : b1) Tighten four M6 screws at the bottom of the bracket (Figure 4-5). 14

15 Figure 4-5: Tighten Bracket b2) Install the threaded rod to the bracket (Figure 4-6). Figure 4-6: Threaded Rod b3) Hold the assembly up to the pole. Attach the two omegas to the threaded rods with M8 nuts, and tighten them (Figure 4-7). 15

16 Figure 4-7: Attach Omegas b4) Proceed to step 11 for grounding. 10. Wall installation: a. Atom OD04/06-14: a1) Slip the bracket off of the Atom unit, and fit the unit on the wall to mark the drilling locations (Figure 4-8). Figure 4-8: Remove Bracket a2) Drill four 10-mm diameter and 70-mm depth holes in the wall, following the marked locations. a3) Check the up/down direction of the bracket, and then fix it on the wall using the M5 tapping screws (Figure 4-9). 16

17 Figure 4-9: Fix Bracket to Wall a4) Install the unit to the bracket, and tighten the screws (Figure 4-10). Figure 4-10: Install Unit b. Atom OD04/ : b1) Put the bracket on the wall, and mark the drilling locations (Figure 4-11). Figure 4-11: Mark Drilling Locations b2) Drill two 12-mm (0.5-in) diameter and 80-mm (3.1-in) depth holes on the marked locations. b3) Install the expansion bolts on the hole with a hammer. b4) Install the bracket on the expansion, and tighten the screws (Figure 4-12). 17

18 Figure 4-12: Install Bracket b5) Proceed to step 11 for grounding. 11. Grounding the Atom OD04/ : The unit must be grounded. Using the grounding cable, connect the grounding screw to the ground row shown in Figure Figure 4-13: OD04/ Grounding 18

19 5 Basic Configuration To configure the Atom outdoor user equipment (UE), you will access the local or Web-based GUI application. Follow the steps provided to log in and complete the minimal configuration requirements for the UE to operate. For more detailed configuration information covering all of the GUI fields, refer to the Baicells Configuration and Network Administration Guide on the Baicells website. 5.1 Log in and Change the Password Follow the steps below to access and log in to the UE GUI application. 1. Connect the UE power. 2. Open a Web browser, and enter: a. (Gen 2 UEs), b. (Gen 1 UEs), or c. (Gen 1 UEs on firmware older than V1.0.3), and then press Enter. 3. At the login window (Figure 5-1), enter the default user name (admin) and password (admin), and select Login. Figure 5-1: Login 4. After you log in, the main menu is shown in the left navigation pane (Figure 5-2). To protect your UE from unauthorized access, go to System > admin to configure a new password (Figure 5-3). The password may be 5 to 8 ASCII characters (letters, numbers, and special characters). Baicells recommends using a mix of upper and lower case letters plus numbers. Click on SAVE & APPLY. 19

20 Figure 5-2: Main Menu Figure 5-3: Change Password 5.2 Configure Network Mode 1. Go to Network > WAN Settings (Figure 5-4). For the Network Mode, choose either Network Address Translation (NAT) or Bridge mode according to your LTE network setup. NAT allows multiple hosts on a private network to access the internet using a single public IP address. Selecting Bridge mode disables NAT and allows the UE to function as a DHCP server without IP address conflict. 2. Click on SAVE & APPLY to complete the configuration. 20

21 Figure 5-4: Network Mode 5.3 Configure LTE Connection Method 1. Choose Network > LTE Settings to choose the LTE connection setting for this UE as either Auto connect or Manual connect (Figure 5-5) to the LTE network. If you choose Automatic, click on SAVE & APPLY to save your selection. If you choose Manual connect, go to step 2. Figure 5-5: Connection Method 2. To manually connect the UE to the LTE network, choose Manual connect and click on PLMN for Public Land Mobile Network to scan all available networks and to select a specific LTE network to connect to. Select Connect to connect to the network. Use the Disconnect button to disconnect from the selected network. 5.4 Configure Scan Method The Scan Method setting determines which frequencies the UE s routine scan of available frequencies will cover. Scanning is a process of tuning to a specific frequency and measuring the simplest signal quality [e.g., Received Signal Strength Indication (RSSI)]. 21

22 As part of the cell selection and reselection process, the UE performs the scan first and then selects a small number of candidate cells to go through the next step of measuring and evaluating signals to select the best enb to serve it. Go to Network > Scan Method, and select either FullBand, PCI Lock, or Band/Frequency Preferred, as shown in Figure 5-6. The options are explained beneath the figure. Click on Submit to save the configuration. Figure 5-6: Scan Method FullBand The UE will routinely scan all channels in the band, which can make the time it takes to connect longer than the other modes. The band is dependent on the model of UE being used. Click on Submit after selecting this option. Frequency Lock You can specify which band(s) the UE will scan. Select Frequency Lock, and click on Add List. This will open a new window where you can input the band number and the preferred E-UTRA Absolutely Radio Frequency Channel number (EARFCN) (Figure 5-7). Click on Add to add the list. You can add more than one list. PCI Lock Allows you to select the specific E-UTRA Absolute Radio Frequency Channel Number (EARFCN) and Physical Cell Identifier (PCI). Click on Add List to enter the settings (Figure 5-8). After entering the information, click on Add. You can add more than one PCI Lock list. The UE will scan the list for enbs with the PCI and EARFCN combination. After entering the configuration settings, click on SAVE & APPLY to save the changes. Figure 5-7: Frequency Lock 22

23 Figure 5-8: PCI Lock 5.5 Configure APN Management An Access Point Name (APN) is the name of a gateway between a 3G/4G mobile network and another computer network, frequently the public internet. The UE supports 4 APN configurations. Go to LTE > APN Management to configure the different services (Figure 5-9 and Table 5-1). Click on SAVE & APPLY to activate the data. The bottom of the screen lists any APNs that have been defined for this UE. Figure 5-9: APN Management 23

24 Table 5-1: APN Management Field Name Description APN Number Select the APN number 1, 2, 3, or 4 Enable Select the check box next to Enable to enable this APN APN Name Enter the name of this APN, as defined in the enb configuration Default Gateway To enable a default gateway to this enb, select the check box next to Enable. Apply To Select either No [None] Specified, TR069, SNMP, or SNMP+TR069 to indicate which protocol may be used to collect information about the enbs to which this UE may connect. 24

25 Appendix A: Technical Specifications Basic Specifications Item LTE Standard Ethernet LAN Port LED Indicators USIM Restore Button Power Supply Dimensions (HxWxD) Weight Description Atom OD04-14: 3GPP Release 9, CAT4 Atom OD06-14: 3GPP Release 10, CAT 6/7 One RJ-45 port auto-sensing, auto-mdx, PoE: Atom OD04-14: 10/100 Mbps Atom OD06-14: 10/100/1000 Mbps MIU/LTE/SIM/LAN/PWR/LTE SIGNAL 1.8V/3V 2FF Tactile button. Press button for at least 10 seconds to restore the UE to factory settings. Input: Universal range 100V to 240V AC Output: PoE (24VDC, 0.5A) 9.5 x 6 x 2 inches 241 x 154 x 50 millimeters 2 lbs / 900 g RF Specifications Item LTE Mode Channel Bandwidth MAX Output Power TXRX Frequency Bands Peak Rate Antenna Gain Atom OD04-14: FDD/TDD Atom OD06-14: TDD 5 / 10 / 15 / 20 MHz 23 ± 2 dbm / TX antenna Atom OD04-14: 1T2R Atom OD06-14: Description 1T2R / 1T4R 2T2R / 2T4R (uplink enhanced FDD Bands 7/38 (Atom OD04-14 only) TDD Bands 40/41 TDD Bands 42/43/48 FDD: DL 100 Mbps, UL 50 Mbps TDD (Atom OD04-14): DL 100 Mbps, UL 10 Mbps (2:7) TDD (Atom OD06-14): DL 220 Mbps, UL 15 Mbps (2:7) Atom OD04-14: 11 2.x GHz, 2 ports 14 3.x GHz, 2 ports 25

26 Carrier Aggregation Modulation Atom OD06-14: 11 2.x GHz, 2 ports 11 3.x GHz, 4 ports 14 3.x GHz, 2 ports Atom OD06-14 only: 2CC CA Atom OD04-14: UL: QPSK, 16QAM DL: QPSK, 16QAM, 64QAM Atom OD06-14: UL: QPSK, 16QAM, 64QAM DL: QPSK, 16QAM, 64QAM Receive Sensitivity -94 QPSK, 20 MHz, 25 C Antenna Type Polarization ± 45 Antenna Efficiency > 70% Isolation VSWR 2 Horizontal Beamwidth (3 db) Vertical Beamwidth (3 db) Atom OD06-14 notes: Internal directional -25 db Atom OD04-14: 63 ± 2.x GHz, 2 ports 60 ± 3.x GHz, 2 ports Atom OD06-14: 63 ± 2.x GHz, 2 ports 60 ± 3.x GHz, 2 ports 70 ± 3.x GHz, 4 ports Atom OD04-14: 35 ± 2.x GHz, 2 ports 25 ± 3.x GHz, 2 ports Atom OD06-14: 35 ± 2.x GHz, 2 ports 25 ± 3.x GHz, 2 ports 30 ± 3.x GHz, 4 ports Note 1: Different models support different frequencies, antennas, and Carrier Aggregation configurations. Note 2: The current version supports only the 2-port antenna. 26

27 Wi-Fi Specifications Item Standard Channel Bandwidth Frequency TXRX Peak Rate Modulation Receive Sensitivity Max Output Power Antenna Type Antenna Gain IEEE b/g/n 20/40 MHz 2.4 GHz 1T1R b: 11 Mbps g: 54 Mbps n: 300 Mbps DSSS/CCK, OFDM Description Mbps, typical for n Mbps, typical for g Mbps, typical for b 10 ± 3 dbm Internal omni 0 dbi Software Specifications Item Description Network Mode NAT / Bridge / Tunnel IP Protocol IPv4 / IPv6 Universal Subscriber Identity Management: USIM PIN management SIM lock Network Connection Management Auto / Manual LTE Scan Mode Full band scan, frequency lock WPS WLAN MSSID isolation VLAN Atom OD : L2TP GRE PPTP VPN L2 VxLAN Atom OD : L2TP L2/L3 GRE L2/L3 Port forwarding Port trigger NAT DMZ ALG Firewall IP/MAC/URL filter 27

28 Item Network Management Diagnostics Maintenance System Logs Statistics Description Access control Block port scanner / SYN flood SPI filter TR069 SNMP TCP dump Ping Trace route Data and time setting Reboot Restore factory settings Restore / back up configuration files Firmware upgrade locally or OTA Operating Run-time Filter / select / display / export LTE status / connection time /system up time Device status DHCP client list Wi-Fi station list Firewall status Environmental Specifications Item Description Operating Temperature -40 F to 131 F, -40 ~ 55 Storage Temperature -40 F to 158 F, -40 to 70 Operating Humidity 5% ~ 95% Ingress Protection Rating IP65 Global Part Numbers Model Name Description EG7010C-M1 Atom Outdoor 14 dbi UE, CAT 6/7, 2T2R, Bands 40/41 EG7010D-M11 Atom Outdoor 14 dbi UE, CAT 6/7, 2T2R, Bands 42/43/38 EG7035L-M1 OD04-14: Bands 40/41 EG7035L--M2 OD04-14: Bands 42/43 EG7035L-M10 OD04-14: Bands 7/38 EG7035L-M11 OD04-14: Bands 42/43/48 EG7011B-M2 OD04-14: Bands 42/43 28

29 Appendix B: Technical Specifications Basic Specifications Item LTE Standard Ethernet LAN Port LED Indicators USIM Restore Button Power Supply Dimensions (HxWxD) Weight Description Atom OD : 3GPP Release 9, CAT4 Atom OD : 3GPP Release 10, CAT 6/7 One RJ-45 port auto-sensing, auto-mdx, PoE: Atom OD : 10/100 Mbps Atom OD : 10/100/1000 Mbps MIU/LTE/SIM/LAN/PWR/LTE SIGNAL 1.8V/3V 2FF Tactile button. Press button for at least 10 seconds to restore the UE to factory settings. Input: Universal range 100V to 240V AC Output: PoE (24VDC, 0.5A) 9.8 x 9.8 x 3.2 in 248 x 248 x 80 mm 4 lbs / 1800 g RF Specifications Item LTE Mode Channel Bandwidth MAX Output Power TXRX Frequency Bands Peak Rate Atom OD : FDD/TDD Atom OD : TDD 5 / 10 / 15 / 20 MHz 23 ± 2 dbm Description Atom OD : 1T2R Atom OD : 1T2R/1T4R, 2T2R/2T4R (uplink enhanced) Atom OD : Bands 7/38 Bands 40/41 Bands 42/43/48 Atom OD : Bands 40/41/42/43/48 Customized Atom OD : FDD: DL 100 Mbps, UL 50 Mbps TDD: DL 100 Mbps, UL 10 Mbps (2:7) 29

30 Antenna Gain Modulation Atom OD : TDD: DL 220 Mbps, UL 15 Mbps (2:7) OD : 14 2.x GHz, 2 ports x GHz, 2 ports OD : 14 2.x GHz, 2 ports x GHz, 2 ports 11 2.x GHz, 4 ports 14 3.x GHz, 4 ports Atom OD : UL: QPSK, 16QAM DL: QPSK, 16QAM, 64QAM Atom OD : UL: QPSK, 16QAM, 64QAM DL: QPSK, 16QAM, 64QAM Receive Sensitivity -94 QPSK, 20 MHz, 25 C Antenna Type Polarization ± 45 Antenna Efficiency > 70% Isolation Internal directional -20 db VSWR 2.5 Horizontal Beamwidth (3 db) Vertical Beamwidth (3 db) OD : 35 ± 2.x GHz, 2 ports 25 ± 3.x GHz, 2 ports OD : 35 ± 2.x GHz, 2 ports 25 ± 3.x GHz, 2 ports 60 ± 2.x GHz, 4 ports 25 ± 3.x GHz, 4 ports OD : 35 ± 2.x GHz, 2 ports 25 ± 3.x GHz, 2 ports OD : 35 ± 2.x GHz, 2 ports 25 ± 3.x GHz, 2 ports 35 ± 2.x GHz, 4 ports 25 ± 3.x GHz, 4 ports 30

31 Wi-Fi Specifications Item Standard Channel Bandwidth Frequency TXRX Peak Rate Modulation Receive Sensitivity Max Output Power Antenna Type Antenna Gain IEEE b/g/n 20/40 MHz 2.4 GHz 1T1R b: 11 Mbps g: 54 Mbps n: 300 Mbps DSSS/CCK, OFDM Description Mbps, typical for n Mbps, typical for g Mbps, typical for b 10 ± 3 dbm Internal omni 0 dbi Software Specifications Item Network Mode IP Protocol USIM Network Connection Management LTE Scan Mode WLAN VPN NAT Firewall Description NAT / Bridge / Tunnel IPv4 / IPv6 Universal Subscriber Identity Management: PIN management SIM lock Auto / Manual Full band scan, frequency lock WPS MSSID isolation VLAN Atom OD : L2TP GRE PPTP L2 VxLAN Atom OD : L2TP L2/L3 GRE L2/L3 Port forwarding Port trigger DMZ ALG IP/MAC/URL filter Access control Block port scanner / SYN flood 31

32 Item Network Management Diagnostics Maintenance System Logs Statistics Description SPI filter TR069 TR104 (Atom OD only) SNMP TCP dump Ping Trace route Data and time setting Reboot Restore factory settings Restore / back up configuration files Firmware upgrade locally or OTA Operating Run-time Filter / select / display / export Atom OD : LAN link status Transmit/receive traffic Run time Atom OD : LTE status / connection time /system up time Device status DHCP client list Wi-Fi station list Firewall status Environmental Specifications Item Description Operating Temperature -40 F to 131 F, -40 to 55 Storage Temperature -40 F to 158 F, -40 to 70 Operating Humidity 5% to 95% Ingress Protection Rating IP67 Global Part Numbers Model Name EG7010A-M11 Description Atom OD dbi, 3.5 GHz User Equipment EG7035E-M1 Atom OD dbi UE: Bands 40/41 EG7035E-M2 Atom OD dbi UE: Bands 42/43 EG7035E-M10 Atom OD dbi UE: Bands 7/38 EG7035E-M11 Atom OD dbi UE: Bands 42/43/48 32

33 Appendix C: CE Statement Baicells Technologies Co., Ltd. hereby declares that this LTE and Wi-Fi Wireless Terminal is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. 1. The plug is considered a disconnect device of the adaptor. 2. The device complies with RF specifications when the device is used at 16 inches (40 cm) from your body. 33

34 Appendix D: FAQs If you have questions, please check the list of frequently asked questions (FAQs) on the Baicells support website or the Facebook support forum. Baicells support website - Baicells support forum on Facebook