Paradyne Student Guide GranDSLAM 4.X. GranDSLAM 4.X. Revision Paradyne Corporation Page 1

Transcription

1 Paradyne Student Guide GranDSLAM 4.X GranDSLAM 4.X Revision Paradyne Corporation Page 1

2 GranDSLAM 4.X Student Guide Paradyne Phone: Fax: Address: th Avenue North Largo, Florida Internet: Prepared by: Paradyne Corporation World Wide Service and Support Copyright 2004 Paradyne Corporation. All rights reserved. No part of this document shall be reproduced, stored in a retrieval system, or transmitted by any means, electronic, magnetic, mechanical, photocopying, recording, xerographic, or otherwise, without the express written permission of Paradyne. Page Paradyne Corporation Revision 1.0

3 Paradyne Student Guide GranDSLAM 4.X Contents FEATURES AND FUNCTIONS...7 FEATURES AND FUNCTIONS (CONTINUED)...9 TRIPLE PLAY NETWORK...11 OUT OF BAND MANAGEMENT ACCESS...13 IP/SCP SWITCH CAPACITY...15 CONFIGURATION MENU...17 MANAGEMENT MENU...19 USERS...21 ATM MANAGEMENT PVC...23 IP PORT...25 IN-BAND MANAGEMENT SCP...27 IP SECURITY...29 IP ROUTING...31 SNMP...33 GIGE INTERFACE /100 ETHERNET UPLINK...37 BRIDGE...39 ADSL2+ LINE PROFILE DISPLAY...41 ADSL2+ LINE PROFILE CREATE...43 ADSL2 & 2+ PSD DISPLAY...45 ADSL2 & 2+ MODIFY...47 ADSL ALARM PROFILE DISPLAY...49 ADSL ALARM PROFILE CREATE...51 SHDSL LINE PROFILE CREATE...53 ADSL PORT...55 SHDSL PORT...57 ADSL PROFILE DISPLAY...59 ATM PROFILE CREATE...61 VLAN DEFAULT...63 Revision Paradyne Corporation Page 3

4 GranDSLAM 4.X Student Guide Paradyne TRIPLE PLAY (VOICE, VIDEO AND INTERNET)...65 VLAN CONFIGURATION...67 ALARMS AND STATUS...69 TRIPLE PLAY VLAN CONFIGURATION...71 DSL CONNECTIONS...73 TRIPLE PLAY DSL CONNECTIONS...75 MULTICAST COMMON PARAMETERS...77 MULTICAST PORT PARAMETERS...79 CLOCKING...81 VLAN CONFIGURATION...83 DATE AND TIME...85 STATUS MENU...87 SYSTEM ALARMS...89 PORT RATES...91 SYSLOG...93 UNKNOWN CELL LOG...95 BANDWIDTH UTILIZATION...97 DSL PERFORMANCE...99 DSL PERFORMANCE CONTINUED SHDSL PERFORMANCE ETHERNET PERFORMANCE FINISHED VLAN CONFIGURATION FINISHED VLAN CONFIGURATION SYSTEM MENU FIRMWARE FINISHED VLAN CONFIGURATION FINISHED VLAN CONFIGURATION SYSTEM INFORMATION SLOT INFORMATION Page Paradyne Corporation Revision 1.0

5 Paradyne Student Guide GranDSLAM 4.X This page intentionally left blank. Revision Paradyne Corporation Page 5

6 GranDSLAM 4.X Student Guide Paradyne Features and Functions Out of band Management eth1 eth2 eth3 Ethernet Layer 2 Switch ATM Switch DSL Ports Up to 864 User Data Page Paradyne Corporation Revision 1.0

7 Paradyne Student Guide GranDSLAM 4.X Features and Functions Port 1 (eth1) Out of Band management port only. Connected physically and logically only to the IP/SCP. Port 2 & 3 (eth2 & 3) Can be used for either customer data as well as in-band management traffic. Eth2 is a copper 10/100meg connection Eth3 is either copper or fiber GigE connection (1000) only By default eth2, eth3 and all of the DSL ports are all assigned to VLAN 1. The switch cannot filter on well know IP port numbers. The switch can be configured so that each DSL port can have up to 8 VPI/VCI connections. Each VPI/VCI can be assigned to a unique VLAN. Each ATM connection / VLAN can be assigned different levels of priority (8 highest, 1 lowest). All ATM traffic over the DSL link is UBR. End to end quality of service is done through VLAN groups using the eight port queues (ATM queue number). Revision Paradyne Corporation Page 7

8 GranDSLAM 4.X Student Guide Paradyne Features and Functions Out of band Management eth1 eth2 eth3 Ethernet Layer 2 Switch ATM Switch DSL Ports Up to 864 User Data Page Paradyne Corporation Revision 1.0

9 Paradyne Student Guide GranDSLAM 4.X Features and functions (continued) The IP/SCP is designed to fit into the following networks: Private MTU Networks and Telco Networks Video applications can only be supported by the 8965 ADSL (this is due to the fact that video applications require a minimum of 3.5 to 4 Meg connection per video stream). There are three different modes of operation for the internal layer 2 switch. These modes of operation are mutually exclusive. By default all Ethernet switches must have at least one group or VLAN that is active. In the case of the IP/SCP VLAN 1 is active for Secure VLAN and Switch modes of operation. In the case of Uplink Tagging each DSL port is assigned a unique VLAN. Secure VLAN This is the default mode of operation, which performs security between DSL ports. All traffic from a DSL port is directed to the uplink. There is an additional Ethernet management port, which is for out of band management for the unit, which has a default IP address of Switch Mode This is basic Ethernet switching where all ports have equal access. Uplink Tagging The default for this mode is that each DSL port is assigned to a unique VLAN and that the uplink will be using 802.1Q tagging to distinguish between ports. Revision Paradyne Corporation Page 9

10 GranDSLAM 4.X Student Guide Paradyne 802.1P Network That supplies the following Middleware server Additional VOD Servers Multicast Video VoIP Internet Triple Play Network VOD Server Ethernet Port that does the following 802.1P 802.1Q IGMP Querier Five VLANs using in-band management Two connections One for unicast & one for Multicast STB 802.1p CPE Ethernet Switch connection that does the following 802.1P 802.1Q DSL Port with four ATM VCCs One additional VCC for Multicast IGMP query replies Page Paradyne Corporation Revision 1.0

11 Paradyne Student Guide GranDSLAM 4.X Triple Play Network 802.1P The IP network that is connected to the IP/SCP must support both 802.1Q tagging (where multiple logical connections are supported by a single physical connection), and 802.1P which is prioritizing of traffic over Ethernet. This network will have connections to the following devices and or networks: Video middleware server supplies the STB with code and channel guide Multicast head end supplies the MPEG encoded live content VOD servers supplies the local VOD server with additional pay per view MPEG video content VoIP Gateway / Softswitch supplies the voice connection back to the PSTN Internet ISP supplies the high speed Internet connection SNMP Management control for the CO connected devices Ethernet switch must support the following: 802.1P prioritization 802.1Q (Cisco refers to this as trunking) a minimum of four VLANs are required to support triple play (Video [multicast and unicast], voice and Internet) IGMP Version 2 IGNP querier sends an IGMP multicast query to the STB to see if a multicast channel is still being used (this would only be used on the port going to the 4200IP/2600 VOD Server this can supply either all of the VOD content or it can supply only a portion of the VOD content. The portion of the VOD content could be anything from a video clip to a portion of the movie. This is based on multiple factors, first is that in some cases content providers require you to pay royalties based on the number of copies of a video, how big and how many servers do you want to deploy, and how much bandwidth do you have available with in your network. IP/SCP Ethernet Port 802.1P will start and stop at this interface and 802.1Q, minimum of four VLANs configured DSL Port will have four VCCs configured each with a different priority (must match the 802.1P from the Ethernet interface), voice having the highest priority CPE must be an Ethernet switch device that supports VCC to Ethernet port mapping. Two VCC connections will be assigned to the port that has the STP attached. These two connections are for the unicast and multicast video streams. STB can be either thin client (HTML) or thick client (JAVA) and must support the following: Middleware server VOD server Multicast headend Revision Paradyne Corporation Page 11

12 GranDSLAM 4.X Student Guide Paradyne Out of Band Management SCP Console (A) 9600, 8, 1, N, No Flow Control (cable and adapter are supplied with SCP) Default IP = Login SUPERUSER Password ASN#1500 Commands configure management out-of-band address configure management default-gateway Page Paradyne Corporation Revision 1.0

13 Paradyne Student Guide GranDSLAM 4.X Out of Band Management Access The SCP uses the same cable and adapter that was used by the MCP. You now will have to plug it into the Serial SCM (SCP) port. Both slot A and B can be accessed. The only SCP that responds is the active one. Revision Paradyne Corporation Page 13

14 GranDSLAM 4.X Student Guide Paradyne IP/SCP Switch Capacity SCP 2.4 Gig ADSL Meg Down and 50 Meg Up Reach 18 Meg SHDSL 50 Meg Up and Down Page Paradyne Corporation Revision 1.0

15 Paradyne Student Guide GranDSLAM 4.X IP/SCP Switch Capacity IP/SCP Performs all policing and CAC at the DSL ports and VLAN tagging and queuing on the Ethernet side. CAC for CBR is 100% (not displayed), for rt/vbr & nrt/vbr is defaulted to 200% Throttling of traffic can be done for both versions of VBR Configuration changes are done in real time to both SCPs. Ethernet and ATM switching are only done on the IP/SCP. Firmware and configurations only exist on the SCP. Revision Paradyne Corporation Page 15

16 GranDSLAM 4.X Student Guide Paradyne Configuration Menu Page Paradyne Corporation Revision 1.0

17 Paradyne Student Guide GranDSLAM 4.X Configuration Menu The configuration menu reflects the cards that are discovered by the SCP The following is the order that will be used during this module; Management System Ethernet (physical uplink) Reach/ADSL SHDSL DSL Connections Multicast (only if you will be supporting multicast video) Revision Paradyne Corporation Page 17

18 GranDSLAM 4.X Student Guide Paradyne Management Menu Page Paradyne Corporation Revision 1.0

19 Paradyne Student Guide GranDSLAM 4.X Management Menu Users = login, passwords and restrictions ATM Mgmt PVC = used for in-band management for the SCP and or endpoint routers N/A IP Port = IP address associated to the management port selection IP Security = access list IP Routing = defines what networks the SCP will respond to and the next hop router address SNMP = community names and trap managers Revision Paradyne Corporation Page 19

20 GranDSLAM 4.X Student Guide Paradyne Users Page Paradyne Corporation Revision 1.0

21 Paradyne Student Guide GranDSLAM 4.X Users Privilege Level there are four access levels Superuser (everything), Provisioning (no management access), Maintenance (no configuration), Retrieve (view only) Revision Paradyne Corporation Page 21

22 GranDSLAM 4.X Student Guide Paradyne ATM Management PVC Page Paradyne Corporation Revision 1.0

23 Paradyne Student Guide GranDSLAM 4.X ATM Management PVC This screen displays the internal IP address assigned to the IP/SCP. This address can not be changed. It for internal use only. The SCP performs a NAT function for all SNMP commands. This address is part of Paradyne s IP address domain. Revision Paradyne Corporation Page 23

24 GranDSLAM 4.X Student Guide Paradyne IP Port Page Paradyne Corporation Revision 1.0

25 Paradyne Student Guide GranDSLAM 4.X IP Port The SCP can have a static address or use DHCP. The two ATM connections would be used to support CPE devices that support RFC1483 routed cells. Connections for the IP/SCP to CPE devices only support RFC 1483 bridged cells. This function is not supported due to the fact that there is no CPE that can support both RFC 1483 routed and bridged cells. ENET MGMT Is the out-of-band management port on the chassis Inband 1 Is the 1000BaseT port on the IP/SCP card Inband 2 Is the 10/100BaseT port on the IP/SCP card Revision Paradyne Corporation Page 25

26 GranDSLAM 4.X Student Guide Paradyne In-Band Management SCP Page Paradyne Corporation Revision 1.0

27 Paradyne Student Guide GranDSLAM 4.X In-Band Management SCP This is an example of how to associate the SCP IP address to a VLAN Configuration mode allows for support for either DHCP or manual. Revision Paradyne Corporation Page 27

28 GranDSLAM 4.X Student Guide Paradyne IP Security Page Paradyne Corporation Revision 1.0

29 Paradyne Student Guide GranDSLAM 4.X IP Security This screen allows you enter IP addresses that would be allowed to access the Revision Paradyne Corporation Page 29

30 GranDSLAM 4.X Student Guide Paradyne IP Routing Page Paradyne Corporation Revision 1.0

31 Paradyne Student Guide GranDSLAM 4.X IP Routing This screen is designed to tell the SCP as to what Address ranges it is to respond to and how to get to them. Revision Paradyne Corporation Page 31

32 GranDSLAM 4.X Student Guide Paradyne SNMP Page Paradyne Corporation Revision 1.0

33 Paradyne Student Guide GranDSLAM 4.X SNMP This screen allows the user to select the SNMP version that the SCP will respond to, the IP addresses for traps, and the two community strings for accessing the SCP. Revision Paradyne Corporation Page 33

34 GranDSLAM 4.X Student Guide Paradyne GigE Interface Page Paradyne Corporation Revision 1.0

35 Paradyne Student Guide GranDSLAM 4.X GigE Interface These are the standard GigE parameters. Revision Paradyne Corporation Page 35

36 GranDSLAM 4.X Student Guide Paradyne 10/100 Ethernet Uplink Page Paradyne Corporation Revision 1.0

37 Paradyne Student Guide GranDSLAM 4.X 10/100 Ethernet Uplink Rate can be set to auto or to a specific speed. Revision Paradyne Corporation Page 37

38 GranDSLAM 4.X Student Guide Paradyne Bridge Page Paradyne Corporation Revision 1.0

39 Paradyne Student Guide GranDSLAM 4.X Bridge Secure VLAN is where traffic from each user is directed to the defined Ethernet uplink. User ports can not directly communicate using the DSLAM. Switch VLAN is where each port has equal access. Uplink Tag Per Port is used in a VBN solution where a unique VLAN is required to identify each port. The VBN server can then cross reference a DSLAM port number to a room number. Revision Paradyne Corporation Page 39

40 GranDSLAM 4.X Student Guide Paradyne ADSL2+ Line Profile Display Page Paradyne Corporation Revision 1.0

41 Paradyne Student Guide GranDSLAM 4.X ADSL2+ Line Profile Display The line profile defines the link parameters. The profile name is how the link parameters are applied to the DSL ports. The line coding (Multimode, DMT, G.lite, or ANSI) are defined when a profile is assigned to a port. The reason for this is that these line profiles are used for both ADSL and Reach. Revision Paradyne Corporation Page 41

42 GranDSLAM 4.X Student Guide Paradyne ADSL2+ Line Profile Create Page Paradyne Corporation Revision 1.0

43 Paradyne Student Guide GranDSLAM 4.X ADSL2+ Line Profile Create The line parameters that are displayed are for ADSL2+. This card supports ADSL, s=1/2, ADSL-2 and ADSL2+. In order to maximize line performance you will need to review the line parameters that the ADSL CPE that you will be using supports and match them. Max Interleave Delay references how the error checking and correction is done (the end result is delay) Max additional Noise Margin The margin level at which the CO will start to drop transmit levels Min Noise Margin The minimum margin used during show time Target Noise Margin The margin used during training Rate Adaptive Mode Initial, Dynamic, Manual Revision Paradyne Corporation Page 43

44 GranDSLAM 4.X Student Guide Paradyne ADSL2 & 2+ PSD Display Page Paradyne Corporation Revision 1.0

45 Paradyne Student Guide GranDSLAM 4.X ADSL2 & ADSL2+ PSD Display These are the default setting for the ADSL2 and ADSL2+. Recommendation is that you do not change these settings. Revision Paradyne Corporation Page 45

46 GranDSLAM 4.X Student Guide Paradyne ADSL2 & 2+ PSD Modify Page Paradyne Corporation Revision 1.0

47 Paradyne Student Guide GranDSLAM 4.X ADSL2 & ADSL2+ Modify This screen allows the user to modify the PSD spectrum that the ADSL link will use. Revision Paradyne Corporation Page 47

48 GranDSLAM 4.X Student Guide Paradyne ADSL Alarm Profile Display Page Paradyne Corporation Revision 1.0

49 Paradyne Student Guide GranDSLAM 4.X ADSL Alarm Profile Display These are the the parameters that are used to generate traps Revision Paradyne Corporation Page 49

50 GranDSLAM 4.X Student Guide Paradyne ADSL Alarm Profile Create Page Paradyne Corporation Revision 1.0

51 Paradyne Student Guide GranDSLAM 4.X ADSL Alarm Profile Create Allows the user to modify what would generate a trap. Revision Paradyne Corporation Page 51

52 GranDSLAM 4.X Student Guide Paradyne SHDSL Line Profile Create Page Paradyne Corporation Revision 1.0

53 Paradyne Student Guide GranDSLAM 4.X SHDSL Line Profile Create Maximum Rate nx64k + 16K (example for a speed equilivent to 20 DS0s would be 20x64K + 16K = Meg Minimum Rate never change (this is the lowest allowable rate) Mode Annex A (US) or B (everywhere else) Remote Management used to communicate with the CPE (ATM Management DSL) Reference Clock System (comes from how the SCP is configured) or Local (internal clock on the 8985) Revision Paradyne Corporation Page 53

54 GranDSLAM 4.X Student Guide Paradyne ADSL Port Page Paradyne Corporation Revision 1.0

55 Paradyne Student Guide GranDSLAM 4.X ADSL Port Line Code Multimode, DMT, G.lite or ANSI ALDSL line profile allows the user to limit the link speed. Revision Paradyne Corporation Page 55

56 GranDSLAM 4.X Student Guide Paradyne SHDSL Port Page Paradyne Corporation Revision 1.0

57 Paradyne Student Guide GranDSLAM 4.X SHDSL Port SHDSL line profile allows the user to limit the SHDSL link speed. Equipment mode allows the port to be connected on a CO SHDSL port by setting the mode to CPE mode. Revision Paradyne Corporation Page 57

58 GranDSLAM 4.X Student Guide Paradyne ATM Profile Display Page Paradyne Corporation Revision 1.0

59 Paradyne Student Guide GranDSLAM 4.X ADSL Profile Display Used to define the type of QOS for a specified connection. The voice descriptor defines a POTs card with 24 POTs ports (not currently supported by the IP/SCP). Revision Paradyne Corporation Page 59

60 GranDSLAM 4.X Student Guide Paradyne ATM Profile Create Page Paradyne Corporation Revision 1.0

61 Paradyne Student Guide GranDSLAM 4.X ATM Profile Create The traffic descriptors that are displayed will be dependent on the Cos (Class of Service) selected PCR (Peak Cell Rate) should be set to the link speed in cells per second SCR (Sustained Cell Rate) the amount of traffic that is used to define the when tagging, policing, packet discard or shaping comes into play CDVT (Cell Delay Variation Tolerance) is the amount of randomness in the inter-arrival time of cells on a given connection that is monitored at the UNI MBS (Maximum Burst Size) is the number of cells that can be sent together at the peak cell rate (this is to maintain conformance with the SCR). Tagging marks cells that do not conform to the SCR Traffic policing activates the ability to tag or discard cells that do not conform to the SCR Packet discard drops cells that are non-compliance (ATM switches can do early packet discarding. This allows the switch to discard all of the cells associated together to be dropped) Shaping allows for the buffering of traffic to maintain SCR Revision Paradyne Corporation Page 61

62 GranDSLAM 4.X Student Guide Paradyne VLAN Default Page Paradyne Corporation Revision 1.0

63 Paradyne Student Guide GranDSLAM 4.X VLAN Default This is the default VLAN that supports all of the DSL and Ethernet ports (864 DSL and 2 Ethernet) Revision Paradyne Corporation Page 63

64 GranDSLAM 4.X Student Guide Paradyne 802.1P Network That supplies the following Middleware server Additional VOD Servers Multicast Video VoIP Internet Triple Play Network VOD Server Ethernet Port that does the following 802.1P 802.1Q IGMP Querier Five VLANs using in-band management Two connections One for unicast & one for Multicast STB 802.1p CPE Ethernet Switch connection that does the following 802.1P 802.1Q DSL Port with four ATM VCCs One additional VCC for Multicast IGMP query replies Page Paradyne Corporation Revision 1.0

65 Paradyne Student Guide GranDSLAM 4.X Triple Play (Voice, Video and Internet) There are a number of requirements before the triple play solution will operate. Must use a layer 2 switch on the uplink that supports 802.1Q tagging (Cisco s term for this is 802.1Q trunking). Prioritization of user traffic by 802.1p is required from the source of the user traffic to the uplink on the IP/SCP. The IP/SCP will then use the internal prioritization queues to replicate the prioritization to the subscriber. The IP/SCP cannot be set to Uplink Tagging. Initial testing should be done with the IP/SCP set to switch to simplify testing and troubleshooting. Must have an Ethernet Layer 2 switch ADSL CPE that supports port VLANs (VCC to a unique Ethernet port). Comtrend makes 4-port units that do this. We are working with ASUS to make a similar unit. The following are the steps that you will need to do to configure the IP/SCP for this application: 1. Set the Bridge mode to Switch or Secure VLAN 2. Modify all ADSL ports to fast mode or the lowest setting for interleaved mode (required for Voice). The software in the IP/SCP has changed in regards to s=1/2. If older code fast, if newer code interleaved = Enable IGMP Snooping on all ports. If the multicast server is not directly attached to the same switch as the IP/SCP then enable Proxy Query. Create a VPI/VCI connection for responding to IGMP queries. 4. Create 3 New VLANs (use the ATM connection numbers to prioritize traffic). Assign all DSL (8 voice, 4 video and 2 internet) ports as untagged members and the Ethernet uplink as the tagged member. 5. Create the three DSL connections for all ports: a. Under DSL Configuration select 8 for Connection (priority) b. Enter the VPI/VCI to be used for Voice (8 is the highest priority connection). c. Enter the VLAN number that corresponds to application for PVID d. Select 802.1p for Queue Method. e. Perform this same function for video and internet connections (4 for video and 2 for internet) VLANs and tagging can also be used to create private connections between DSL ports. Modifying a selected DSL port in the VLAN table and assigning the same VLAN to both DSL ports is how you do this. Revision Paradyne Corporation Page 65

66 GranDSLAM 4.X Student Guide Paradyne VLAN Configuration Page Paradyne Corporation Revision 1.0

67 Paradyne Student Guide GranDSLAM 4.X VLAN Configuration This screen allows the user to create VLANs either 802.1Q or port VLANs Revision Paradyne Corporation Page 67

68 GranDSLAM 4.X Student Guide Paradyne VLAN DSL Port Assignments Page Paradyne Corporation Revision 1.0

69 Paradyne Student Guide GranDSLAM 4.X Alarms and Status This screen allows the user to assign VLAN IDs to ports on a per card basis This example shows that the Ethernet port 2 (10/100BaseT) is being used as the uplink and that the IP/SCP will accept in-bound tags and strip them prior to sending them to the DSL port. The IP/SCP can also support sending the 802.1Q tag to the CPE. The ATM connection will be referenced in the DSL connection screen. The DSL connection ties the VLAN to the ATM connection on the DSL port Revision Paradyne Corporation Page 69

70 GranDSLAM 4.X Student Guide Paradyne Triple Play VLAN Configuration Page Paradyne Corporation Revision 1.0

71 Paradyne Student Guide GranDSLAM 4.X Triple Play VLAN Configuration This screen show all of the VLAN connections that are required to support the Triple Play Solution. Note that the in-band management connection stops at the Ethernet uplink. The ATM connections are as follows VLAN 10 = ATM connection 4 VLAN 1001 = ATM connection 8 VLAN 1002 = ATM connection 7 VLAN 1003 = ATM connection 6 VLAN 1004 = ATM connection 5 Revision Paradyne Corporation Page 71

72 GranDSLAM 4.X Student Guide Paradyne DSL Connections Page Paradyne Corporation Revision 1.0

73 Paradyne Student Guide GranDSLAM 4.X DSL Connections DCL connections are only built on cards that are installed. The default connections use VLAN 1 on the uplink and 0/35 on all of the ports. There are multiple levels of prioritization. Connection Prioritization or Ethernet 802.1p Connection Prioritization assumes that the CPE can support ATM VPI/VCI connections to Ethernet port VLANs Ethernet 802.1p assumes that the CPE supports 802.1p prioritization Note: Use one or the other form of prioritization Revision Paradyne Corporation Page 73

74 GranDSLAM 4.X Student Guide Paradyne Triple Play DSL Connections Page Paradyne Corporation Revision 1.0

75 Paradyne Student Guide GranDSLAM 4.X Triple Play DSL Connections This display show how all of the Triple Play connections are made. 8 = Voice VLAN = Multicast Video VLAN = VOD VLAN = Internet VLAN 1004 Revision Paradyne Corporation Page 75

76 GranDSLAM 4.X Student Guide Paradyne Multicast Common Parameters Page Paradyne Corporation Revision 1.0

77 Paradyne Student Guide GranDSLAM 4.X Multicast Common Parameters Snooping gives the IP/SCP the ability to support multicast video through IGMP version 2 support IGMP Proxy is used when the device that performs IGMP polling is not directly attached to the IP/SCP Revision Paradyne Corporation Page 77

78 GranDSLAM 4.X Student Guide Paradyne Multicast Port Parameters Page Paradyne Corporation Revision 1.0

79 Paradyne Student Guide GranDSLAM 4.X Multicast Port Parameters This screen allows the IP/SCP to support channel changing This connection must get combined at the Ethernet port of the CPE. The IP/SCP combines this connection to the VLAN that supports multicast video Revision Paradyne Corporation Page 79

80 GranDSLAM 4.X Student Guide Paradyne Clocking Page Paradyne Corporation Revision 1.0

81 Paradyne Student Guide GranDSLAM 4.X Clocking Used in conjunction with the 8985 to supply clocking to the SHDSL CPE. Revision Paradyne Corporation Page 81

82 GranDSLAM 4.X Student Guide Paradyne Sys log Configuration Page Paradyne Corporation Revision 1.0

83 Paradyne Student Guide GranDSLAM 4.X VLAN Configuration Allow you to send all of the syslogs to a remote location. Revision Paradyne Corporation Page 83

84 GranDSLAM 4.X Student Guide Paradyne Date and Time Page Paradyne Corporation Revision 1.0

85 Paradyne Student Guide GranDSLAM 4.X Date and Time This screen allows you to either use a SNTP server or to manually set the date and time. The system uses the date and time for two functions; SNMP traps SYS Log Revision Paradyne Corporation Page 85

86 GranDSLAM 4.X Student Guide Paradyne Status Menu Page Paradyne Corporation Revision 1.0

87 Paradyne Student Guide GranDSLAM 4.X Status Menu Status displays current system parameters Performance displays current link performance values (cells sent and received, link receive levels, etc.) Statistics displays historical (last 24 hours) link (errored seconds) Revision Paradyne Corporation Page 87

88 GranDSLAM 4.X Student Guide Paradyne System Alarms Page Paradyne Corporation Revision 1.0

89 Paradyne Student Guide GranDSLAM 4.X System Alarms This will display current status, firmware, and card type. Slot Alarms will display in detail what the alarm values are for the selected card Revision Paradyne Corporation Page 89

90 GranDSLAM 4.X Student Guide Paradyne Port Rates Page Paradyne Corporation Revision 1.0

91 Paradyne Student Guide GranDSLAM 4.X Port Rates This screen displays the current port speeds for a selected slot Revision Paradyne Corporation Page 91

92 GranDSLAM 4.X Student Guide Paradyne Syslog Page Paradyne Corporation Revision 1.0

93 Paradyne Student Guide GranDSLAM 4.X Syslog The syslog display shows all of the status messages for a selected card/slot. Revision Paradyne Corporation Page 93

94 GranDSLAM 4.X Student Guide Paradyne Unknown Cell Log Page Paradyne Corporation Revision 1.0

95 Paradyne Student Guide GranDSLAM 4.X Unknown Cell Log Unknown cell log is used to display the cells that have not been defined or are in error (header) on a given port Revision Paradyne Corporation Page 95

96 GranDSLAM 4.X Student Guide Paradyne Bandwidth Utilization Page Paradyne Corporation Revision 1.0

97 Paradyne Student Guide GranDSLAM 4.X Bandwidth Utilization Displays the amount of traffic that has been assigned to a specified QOS Revision Paradyne Corporation Page 97

98 GranDSLAM 4.X Student Guide Paradyne DSL Performance Page Paradyne Corporation Revision 1.0

99 Paradyne Student Guide GranDSLAM 4.X DSL Performance This is the top portion of the ADSL performance screen Revision Paradyne Corporation Page 99

100 GranDSLAM 4.X Student Guide Paradyne DSL Performance Continued Page Paradyne Corporation Revision 1.0

101 Paradyne Student Guide GranDSLAM 4.X DSL Performance Continued This is the bottom portion of the ADSL performance screen The bottom line(s) show the actual connections and traffic for each connection Revision Paradyne Corporation Page 101

102 GranDSLAM 4.X Student Guide Paradyne SHDSL Performance Page Paradyne Corporation Revision 1.0

103 Paradyne Student Guide GranDSLAM 4.X SHDSL Performance Bottom of the screen displays ATM PVC performance. Revision Paradyne Corporation Page 103

104 GranDSLAM 4.X Student Guide Paradyne Ethernet Performance Page Paradyne Corporation Revision 1.0

105 Paradyne Student Guide GranDSLAM 4.X Ethernet Performance The current uplink Ethernet statistics You have two selections: Ethernet 1 (1000BaseT fiber or copper) or Ethernet 2 (10/100BaseT) Revision Paradyne Corporation Page 105

106 GranDSLAM 4.X Student Guide Paradyne DSL Statistics Page Paradyne Corporation Revision 1.0

107 Paradyne Student Guide GranDSLAM 4.X Finished VLAN Configuration Allows the user to view link statistics in 15-minute increments for the last 24 hours Revision Paradyne Corporation Page 107

108 GranDSLAM 4.X Student Guide Paradyne SHDSL Statistics Page Paradyne Corporation Revision 1.0

109 Paradyne Student Guide GranDSLAM 4.X Finished VLAN Configuration Allows the user to view link statistics in 15-minute increments for the last 24 hours Revision Paradyne Corporation Page 109

110 GranDSLAM 4.X Student Guide Paradyne System Menu Page Paradyne Corporation Revision 1.0

111 Paradyne Student Guide GranDSLAM 4.X System Menu Firmware upload new code using tftp, switch between code versions (there is support for two versions). The code is only loaded on to the active SCP. The code and the configuration are loaded onto the secondary SCP prior to switching. Restart any or all cards Save and Restore Configuration to a FTP server Revision Paradyne Corporation Page 111

112 GranDSLAM 4.X Student Guide Paradyne Firmware Page Paradyne Corporation Revision 1.0

113 Paradyne Student Guide GranDSLAM 4.X Firmware File name the FTP server must know where the file is located (directory) prior to initiating the download Revision Paradyne Corporation Page 113

114 GranDSLAM 4.X Student Guide Paradyne Restart Page Paradyne Corporation Revision 1.0

115 Paradyne Student Guide GranDSLAM 4.X Finished VLAN Configuration This screen allows the user to restart a selected slot Revision Paradyne Corporation Page 115

116 GranDSLAM 4.X Student Guide Paradyne Save and Restore Page Paradyne Corporation Revision 1.0

117 Paradyne Student Guide GranDSLAM 4.X Finished VLAN Configuration This screen allows the user to reset the 8820 back to factory defaults Save and or restore the 8820 configuration to or from a FTP server Set the 8820 to the selected downloaded configuration Revision Paradyne Corporation Page 117

118 GranDSLAM 4.X Student Guide Paradyne System Information Page Paradyne Corporation Revision 1.0

119 Paradyne Student Guide GranDSLAM 4.X System Information Allows the user to set information in the unit that will be displayed during the SNMP discovery Revision Paradyne Corporation Page 119

120 GranDSLAM 4.X Student Guide Paradyne Slot Information Page Paradyne Corporation Revision 1.0

121 Paradyne Student Guide GranDSLAM 4.X Slot Information Displays the current manufacturing information from a selected slot Revision Paradyne Corporation Page 121

122 GranDSLAM 4.X Student Guide Paradyne This page intentionally left blank. Page Paradyne Corporation Revision 1.0