SPACE REQUIREMENTS AND PLANNING GUIDE

Transcription

1 SPE REQUIREMENTS N PLNNING GUIE Width Measurements L Height from platen glass with document feeder open MX-F10 MX-F11 MX-R18 E F G H I J Note: In addition to the above dimensions, allow three feet of space on all sides f consumable replenishment, paper jam removal, maintenance service procedures. Images may not be to scale. K MX-MF11 5-1/8" 30-1/4" 13-1/4", E 36" F 6-1/2" G 8-3/8" H 34-3/8" I, J 35-1/4" K 240-1/4" L 23" Installing ealer Read this document in its entirety befe planning your configuration. Plan ahead make sure your installation is a great success! Remember to check the latest infmation on these products make sure that the following items are available pri to installation. Verify dedicated power source check f stability. The MX-M1055/ M1205 ocument Systems require a V, 60 Hz, 20 mp power source. The main unit requires one V, 20 mp power source. epth Measurements (overhead view).* 31 1 /8" 48 7 /8" Measurements with,, MX-MFX1 MX-L12.* The,,, options each require separate 120 V, 15 mp power sources. onfirm that you have the latest firmware available from to upgrade your ocument Systems immediately. MX-R13 MX-MF /4" Some accessies require a product key f operation. You should obtain the accessy pplication ode machine s serial number to register the product key online pri to arrival at the customer location. MX-L12 heck to see if My Sharp online training is set up f the end-user /8" 8 3 /8" 48 7 /8" 14 3 /4" Measurements f G SmartPunch Pro ooklet Maker System.* Verify that the customer has enough supplies on-h to complete a large rush job. fter-hours printing / holiday wk may take place following an installation. See Supplies & ccessies list on the following page. G MX-GX2 MX-F50 MX-TM50 MX-M50 MX-F50 3" Exit Tray included with MX-M50 39" 16 3 /4" 23 3 /4" 14" 14" 35 1 /2" * Illustrations shown are f measurement purposes only may not be to scale. F configurations see subsequent pages Sharp Electronics pation. ll rights reserved. MX-X /4" 78"

2 onfiguration chart STEP 1: HOOSE PPER FEE ONFIGURTION Status Indicat can be added to any configuration. MX-MFX1* 100-sheet Multi ypass Tray MX-L12 Large apacity assette (Letter) onfiguration These configurations require the MX-MFX1. These items cannot be combined with items from paper feed configuration. MX-MF sheet Multi ypass Tray onfiguration * The MX-MFX1 is required if no other paper feed options are selected. MX-R16 LT Mounting Kit Large apacity Tray (2 rawers; Ledger) MX-R17 LT onnecting Kit (required f 2nd MX-L13) Large apacity Tray (2 rawers; Ledger) This configuration requires the MX-R16. n MX-R17 is required to connect two Large apacity Trays. The MX-MF11 can also be added to the first, but cannot be used alone. These items cannot be combined with items from paper feed configuration. 1. ase 2. MX-L MX-MFX1 5. MX-MF11 Suppted Paper Weights 1. ase Upper rawer (tem): 16 lb. ond to 28 lb. ond Middle/Lower rawer: 16 lb. ond to 100 lb. ristol 2. MX-L12 16 lb. ond to 100 lb. ristol 3. MX-L13 Upper/Lower rawer: 15 lb. ond to 110 lb. over 4. MX-MFX1 15 lb. ond to 110 lb. over 5. MX-MF11 15 lb. ond to 100 lb. ristol Supplies & ccessies Toner artridge eveloper rum Waste Toner ottle MX-900NT MX-900NV MX-850NR MX-850H 120V/15 Power Filter (f,, MX-L13, ) V/20 Power Filter (f ) R-5133NT MX-E524ZNT 2016 Sharp Electronics pation. ll rights reserved.

3 onfiguration chart STEP 2: HOOSE FINISHING ONFIGURTION onfiguration : 100-sheet Staple Finishing This configuration requires the MX-R18 the. The cannot be used with the. The MX-PN13 can be added, but cannot be used alone. MX-PN13 Punch MX-R18 onfiguration : Stacking This configuration requires the MX-R18 one *. n additional can be added, but is not required. Each includes one MX-10 Paper art. dditional paper carts can be dered f convenience. The Status Indicat can be added to any configuration. / * * MX-F11 2-Tray Inserter MX-R18 Status Indicat onfiguration : asic 100-sheet Staple Finishing This configuration requires the MX-R18 the. The cannot be used with the. The MX-M50* requires the. The MX-F50* must be connected to the MX-TM50*. The MX-SL10 Status Indicat can be added to any configuration. Production ooklet Maker System Exit Tray Included with MX-M50 MX-F50 over Feeder MX-PN13 Punch MX-F50 Square Spine MX-TM50 MX-M50 ooklet Maker MX-P50 Interface Kit MX-R18 MX-X50 Rail (recommended) 2016 Sharp Electronics pation. ll rights reserved.

4 onfiguration chart STEP 2: HOOSE FINISHING ONFIGURTION (continued) onfiguration : dvanced 100-sheet Staple Finishing This configuration requires the MX-R18 the. The MX-F11, both s, MX-GX2, MX-F10, Production ooklet Maker System are all optional. The MX-GX2 requires the MX-R13. The MX-R13 is required to connect a 100-sheet finisher MX-F11. The MX-R13 the MX-F10 is required to connect an to a 100-sheet finisher. The cannot be used with the. The MX-M50 requires the MX-P50. The MX-F50 must be connected to the MX-TM50. The Status Indicat can be added to any configuration. MX-R18 Status Indicat / / / MX-R13 Relay MX-GX2 G SmartPunch Pro TM MX-F11 2-Tray Inserter + MX-R18 (both required f onfiguration ) oth s Required Production ooklet Maker System Exit Tray Included with MX-M50 MX-F50 over Feeder MX-PN13 Punch (continued) MX-F50 Square Spine MX-TM50 MX-M50 ooklet Maker MX-P50 Interface Kit MX-X50 Rail (recommended) 2016 Sharp Electronics pation. ll rights reserved.

5 onfiguration chart STEP 3: SELET ONNETIVITY OMPONENTS Netwk Printing (PL 6/dobe PostScript 3 TM Stard) The MX-PUX1 MX-PF10 cannot be used with the MX-PE11. The MX-PE11 requires the MX-PX11 / MX-PUX1 XPS Expansion Kit MX-PF10 ar ode Font Kit MX-PX11 Fiery Interface Kit MX-PE11 Fiery Server Status Indicat Netwk Scanning 1 (Stard) MX-E11 Enhanced ompression Kit (f Scanning) Security / MX-E15 H Mirring Expansion Kit MX-FR53U ommercial ata Security Kit 2 pplication Integration (MX-MX2 pplication ommunication MX-MX3 External ccounting are stard) E Stamp Kit R-SU1 Stamp (requires R-SV1) R-SV1 Stamp artridge (requires R-SU1) 1 Sharpdesk license upgrade kits are also available, see price list. 2 See price list f availability dates. esign specifications are subject to change without notice. ll product dimensions listed are approximate. Sharp, Sharp OS, My Sharp all related trademarks are trademarks registered trademarks of Sharp pation / its affiliated companies. PL is a registered trademark of HP ompany. dobe PostScript are registered trademarks of dobe Systems Inc. G is a registered trademark of O rs. ll other trademarks are the property of their respective owners Sharp Electronics pation. ll rights reserved. 3/16