SMART WINDOW /DOOR CONTACT

Transcription

1 SMART WINDOW /DOOR CONTACT 1. INTRODUCTION 2 2. PACKAGE CONTENTS 2 3. SPECIFICATIONS 3 4. CHOOSING A SUITABLE LOCATION FOR THE WINDOW/DOOR CONTACTS 4 5. ALARM SIGNALS AND VISUAL INDICATION 8 6. FEDERAL COMMUNICATIONS COMMISSION STATEMENT 9 7. LIMITED PRODUCT WARRANTY 9 8. FAQ CONTACT DISTRIBUTOR 10

2 1. INTRODUCTION This smart window/door contact is a Z-Wave device (interoperable, with RF mesh-network technology which works in two directions) and is compatible with every Z-Wave network and the related security framework. Each device driven by Z-wave functions as a signal amplifier, so that multiple devices ensure a greater number of transition routes, which help to eliminate "RF dead spots". Z-Wave devices with the Z-Wave logo can also be used for this, regardless of the manufacturer. Furthermore, our devices can also be used in Z-Wave networks of other manufacturers. 2. PACKAGE CONTENTS Window/ door contact Mounting kit Battery Quick start guide 2

3 3. SPECIFICATIONS PRODUCT IDENTIFICATION Fifthplay Product ID DIMENSIONS Main component Length Height Width Sensor head Length Height Width POWER CONSUMPTION Battery power RF COMMUNICATION Protocol Frequency range CONTROL PARAMETERS 88 mm 21 mm 25 mm 37 mm 20 mm 12 mm CR123A Lithium Z-Wave MHz Temperature Relative humidity 10 95% Action radius Z-WAVE COMMAND CLASSES 30 m COMMAND_CLASS_ASSOCIATION_GRP_INFO COMMAND_CLASS_ASSOCIATION_V2 COMMAND_CLASS_BATTERY COMMAND_CLASS_CONFIGURATION COMMAND_CLASS_DEVICE_RESET_LOCALLY COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2 COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2 COMMAND_CLASS_NOTIFICATION_V4 (Mapping COMMAND_CLASS_BASIC) COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_SECURITY COMMAND_CLASS_VERSION_V2 COMMAND_CLASS_WAKE_UP_V2 COMMAND_CLASS_ZWAVEPLUS_INFO_V2 3

4 4. INSTALLATION AND ACTIVATION INSTALLATION OF THE BATTERY E 1. Loosen the screws on the rear side (E) of the window/door contact, place the battery and place the rear side back onto the sensor. 2. The LED lamp of the window/door contact will slowly flash for 10 seconds; the sensor is ready for connection to the gateway. 4

5 4.1.2 CONNECTING A WINDOW/DOOR CONTACT TO YOUR FIFTHPLAY CUBE A IMPORTANT: Ensure that the window/door contact is in the immediate vicinity (0.5 to 1 meter) of the gateway. You can connect your window/door contact to your fifthplay cube in the following 2 ways: Via the APP: 1. Open the fifthplay Home app and log in. 2. At the top left of the app, click on and select 'CONFIGURATION'. 3. Go to 'DEVICES'. 4. At the top right, click on Select 'SENSOR' as the type of device. 6. Select 'WINDOW/DOOR CONTACT'. 7. Wait until the gateway is in connection mode (Once the connection mode has been established, you will see a notification on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no devices to be added are found, the connection mode will automatically be terminated after 2 minutes. 8. Hold down the programming button (A) of the window/door contact for at least 1 second to connect it to the gateway. Once the connection has been established, you will see a confirmation message on your screen. 9. Once the window/door contact has been added, you will see a notification on your screen. 10. If desired, change the name of the window/door contact. Via the WEBSITE: 1. Go to home.fifthplay.com and log in. 2. Go to 'CONFIGURATION'. 3. Go to 'DEVICES'. 4. Click on 'ADD A DEVICE'. 5. Click on 'ADD A SENSOR'. 6. Select 'WINDOW/DOOR CONTACT' and click on 'NEXT'. 7. Wait until the gateway is in connection mode (Once the connection mode has been established, you will see a notification on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no devices to be added are found, the connection mode will automatically be terminated after 2 minutes. 8. Hold down the programming button (A) of the window/door contact for at least 1 second to connect it to the gateway. Once the connection has been established, you will see a confirmation message on your screen. 9. Once the window/door contact has been added, you will see a notification on your screen. 10. If desired, change the name of the window/door contact. 5

6 4.1.3 MOUNTING OF THE WINDOW/DOOR CONTACT B C D 1. Mount the largest part of the window/door contact by using the screws or double-sided tape. 2. Place the smallest part of the window/door contact in the right position in between the arrows (B). If desired, you can use the extra mounting bracket (D). Use the double-sided tape or screws to mount the whole unit. 3. The distance between the smallest and the largest part of the window/door sensor (C) may not exceed 1.9 cm. 6

7 4.1.4 DISCONNECTING A WINDOW/DOOR CONTACT FROM YOUR FIFTHPLAY CUBE A IMPORTANT: Ensure that the window/door contact is in the immediate vicinity (0.5 to 1 meter) of the gateway. You can disconnect your window/door contact from your fifthplay cube in the following 2 ways: Via the APP: 1. Open the fifthplay Home app. 2. At the top left of the app, click on and select 'CONFIGURATION'. 3. Go to 'DEVICES'. 4. Select the window/door contact you want to remove. 5. Click on 'REMOVE'. 6. Wait until the gateway is in connection mode (Once the connection mode has been established, you will see a notification on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no devices to be removed are found, the connection mode will automatically be terminated after 2 minutes. 7. Hold down the programming button (A) of the window/door contact for at least 1 second to disconnect it from the gateway. 8. Once the window/door contact has been removed, you will see a notification on your screen. Via the WEBSITE: 1. Go to home.fifthplay.com and log in. 2. Go to 'CONFIGURATION'. 3. Go to 'DEVICES'. 4. Select the window/door contact you want to remove. 5. Click on 'REMOVE DEVICE'. 6. Wait until the gateway is in connection mode (Once the connection mode has been established, you will see a notification on your screen). If this is not the case, click on 'CANCEL' and 'TRY AGAIN'. Please note: If no devices to be removed are found, the connection mode will automatically be terminated after 2 minutes. 7. Hold down the programming button (A) of the window/door contact for at least 1 second to disconnect it from the gateway. 8. Once the window/door contact has been removed, you will see a notification on your screen. 7

8 5. ALARM SIGNALS AND VISUAL INDICATION STATUS ACTIVATION MODE (the battery is being installed in the window/ door contact) OPENING CONTACT the window/door contact is being opened IDLE MODE (the window/door contact is functioning properly) LOW BATTERY VOLTAGE - DISMANTLING SECURITY (the window/door contact is installed incorrectly) INDICATION ON THE WINDOW/ DOOR CON- TACT NOTIFICATION APP REPORTING IN THE APP - - LED flashes once Push notification / text message / - - LED lights up continuously Push notification / text message / Push notification / text message / 8

9 6. FEDERAL COMMUNICATIONS COMMISSION STATEMENT This product complies with all of the relevant European guidelines and regulations. If applicable, you can find the EC declaration of conformity regarding this product at com/downloads. This product cannot be deposited in the unsorted waste. Take your discarded product to a recycling centre or a recognised collection point. Just like producers and importers, you too play an important role in the promotion of sorting, recycling and reuse of waste electrical and electronic equipment. To finance the rubbish collection and waste treatment, the government levies recycling charges in certain cases (included in the price of this product). 7. LIMITED PRODUCT WARRANTY The warranty period is two years from the date of delivery. The delivery date is the invoice date of purchase of the product by the consumer. If there is no invoice, the date of production applies. The consumer is obliged to inform fifthplay in writing about the non-conformity, within two months of noticing the defect. In case of a non-conformity, the consumer only has the right to a product repair or replacement free of charge, which shall be decided by fifthplay. fifthplay shall not be held liable for a defect or damage resulting from incorrect installation, improper or careless use, incorrect operation, transformation of the product, maintenance that does not adhere to the maintenance instructions or an external cause, such as damage due to moisture or overvoltage. The compulsory regulations of the national legislation concerning the sale of consumer goods and the protection of the consumer in the countries where fifthplay sells, directly or via sister companies, subsidiaries, chain stores, distributors, agents or permanent sales representatives, take priority over the above-mentioned rules and regulations. 9

10 8. FAQ Consult our frequently asked questions page on cube.fifthplay.com/faq or consult the user manuals on cube.fifthplay.com/downloads 9. CONTACT Telephone: +32 (0) DISTRIBUTOR Fifthplay NV Generaal Lemanstraat, 47 B-2018 Antwerp 10