For personnal use only

Transcription

1 Adding and Removing Disks From VMware RHEL7 Guests Without Rebooting Finnbarr P. Murphy Consider the following scenario. You are studying for your RHCSA or RHCE using one or more RHEL or CentOS VMs running in a VMware Workstation on a Microsoft Windows OS. You need to practice adding one or more disks (it will come up in the exam!), formatting and partitioning the disks many times so that you can do it accurately, quickly and without hesitation in the actual exam where time is of the essence. In this scenario, most people simply shutdown and power off the guest VM, go into the VM settings, add a new disk, power on the VM where upon the new disk is automatically detected and made available to the OS during the boot process when the hardware is scanned and enumerated. Similarly, when removing a disk from the OS. However, this wastes valuable (usually scarce) study time and can easily be avoided as this post will show you. Adding a new disk to your VM Suppose you currently have the following configuration which is the default OOTB (Out Of The Box) single disk configuration for CentOS 7.2: Copyright Finnbarr P. Murphy. All rights reserved. 1/7

2 and you want to add a new disk to the current single disk configuration without shutting down your CentOS 7 guest. Two utilities you should be very familiar with when examining the current disk configuration as seen from the OS perspective are: lsblk list block devices lsscsi list SCSI devices (hosts) and their attributes We will use both utilities extensively in the remainder of this post. The next image shows one of the VMware Workstation Add Hardware Wizard panes. Note that the default disk type is SCSI not SATA or IDE (PATA). The disk is also persistent. Note also that the VM is running. Leave the disk type as SCSI, do not select either IDE (which does require a reboot) or SATA Copyright Finnbarr P. Murphy. All rights reserved. 2/7

3 OK, you have created your new SCSI disk in VMware Workstation. Does this new disk automatically show up in your running VM? Copyright Finnbarr P. Murphy. All rights reserved. 3/7

4 No, it does not. As shown above, neither lsscsi or lsblk detect the newly added disk. We have to use sysfs to tell the kernel to rescan a bus (AKA channel in SCSI terminology) in order for the kernel to discover the new disk. What is sysfs you may ask. Fortunately, it is not something that you need to know much about for the RHCSA or RHCE exams. From Wikipedia: sysfs is a pseudo file system provided by the Linux kernel that exports information about various kernel subsystems, hardware devices, and associated device drivers from the kernel s device model to user space through virtual files.[1] In addition to providing information about various devices and kernel subsystems, exported virtual files are also used for their configuring. Consider the following commands: Copyright Finnbarr P. Murphy. All rights reserved. 4/7

5 # ls -1 /sys/class/scsi_host host0 host1 host2 # grep mpt /sys/class/scsi_host/host?/proc_name /sys/class/scsi_host/host2/proc_name:mptspi # echo "- - -" > /sys/class/scsi_host/host2/scan The first command lists all the SCSi devices the OS is aware of. The 4 numbers in the square brackets can be represented as [ } where is the host adapter (0 being the first), the channel (bus) on the host adapter (0 being the first), is the target ID, and is the Logical Unit Number (0 being the first.) If you are unfamiliar with SCSI (Small Computer System Interface) concepts, I suggest you read this Wikipedia article especially the part about device identification. The second command lists out all the host adapters. In this case, it lists host0, host1 and host2. This is useful information but it is not sufficient information information to determine if a specific host adapter is connected to a specific hard drive. The third command is used to detect which specific host adapter is handling our new VMware Workstation virtual disk. How does this command work? It works because the default disk controller for a VMware Workstation guest virtual disk is an LSI Logic disk controller. The name of the device driver for a LSI Logic SCSI disk controller in Linux is mptspi. Technically, the full name of the driver is LSI Logic Fusion MPT SPI Host. In the case of another SCSI controller type the name of the driver will differ. For example, If for some reason you used the VMware para-virtual controller, you would need to grep for pvscsi. Now that we know which host adapter our disk is attached to, we issue the fourth command which causes the kernel to rescan all controllers on that particular host adapter, i.e. host2, What is meant by echo - -? Here, the three values - - represent channel(bus), SCSI target ID, and LUN. The dashes act as wildcards meaning rescan everything. Finally, the last command confirms the disk was found by re-runnning lsscsi. To explicitly add a single disk, there is a preferred method and a depreciated method per Red Hat documentation. The preferred method uses the echo > /sys/class/scsi_host/host/scan syntax as shown in the following example: i # echo "0 1 0" > /sys/class/scsi_host/host2/scan The depreciated method uses the echo scsi add-single-device > /proc/scsi/scsi syntax as shown Copyright Finnbarr P. Murphy. All rights reserved. 5/7

6 in the following example: i # echo "scsi add-single-device " > /proc/scsi/scsi The last option that I will discuss is to use a small shell script, such as the one shown below, to discover and rescan all channels on all hosts: #!/bin/bash ls -1 /sys/class/scsi_host while read SCSI_HOST do echo "- - -" > /sys/class/scsi_host/${scsi_host}/scan done This script simply discovers and rescans all channels on all the host adapters. By the way, the Red Hat storage documentation and a Red Hat Knowledgebase article both recommend that you install the sg3_utils package (Linux SCSI Utilities) to rescan SCSI layers using the rescan-scsi-bus.sh script in order to detect when a new virtual disk is added to the guest operating system. Do not bother using this package. It will simply waste you valuable study time and furthermore is buggy. Deleting an Existing VM Disk Suppose you want to delete /dev/sdb. Assuming it is not your primary disk and you have already umounted any filesystems that were using this disk, consider the following set of commands: # ls -l /sys/bus/scsi/drivers/sd/2\:0\:1\:0/block/ total 0 drwxr-xr-x. 7 root root 0 May 7 06:46 sdb # cat /proc/scsi/scsi Attached devices: Host: scsi2 Channel: 00 Id: 00 Lun: 00 Vendor: VMware, Model: VMware Virtual S Rev: 1.0 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: NECVMWar Model: VMware IDE CDR10 Rev: 1.00 Type: CD-ROM ANSI SCSI revision: 05 Host: scsi2 Channel: 00 Id: 01 Lun: 00 Vendor: VMware, Model: VMware Virtual S Rev: 1.0 Type: Direct-Access ANSI SCSI revision: Copyright Finnbarr P. Murphy. All rights reserved. 6/7

7 # echo 1 > /sys/bus/scsi/drivers/sd/2:0:1:0/delete # lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 20G 0 disk sda1 8: M 0 part /boot sda2 8: G 0 part centos-root 253: G 0 lvm / centos-swap 253:1 0 2G 0 lvm [SWAP] sr0 11: M 0 rom The first command lists the SCSI devices currently known to the OS and allows you to identify the the host adopter, channel, target and LUN that /dev/sdb is using. The second and third commands enable you to double check things via a more verbose listing (always a good idea!) The fourth command removes the device /dev/sdb from the operating system. The fifth and sixth commands confirm the device was removed. Good luck studying for your RHCSA or RHCE exam! Copyright Finnbarr P. Murphy. All rights reserved. 7/7