CS141 SNMP / WEB / MODBUS MANAGER

Transcription

1 CS141 SNMP / WEB / MODBUS MANAGER Slot Version External Version CS141SC CS141L CS141MINI Description Function 1 COM1 Port Serial Interface to connect an UPS or another device with a original RS232 cable 2 COM2 Port To connect additional devices for example (GSM Modem, temperature and humidity sensor, SENSORMANAGER_II, Fieldbus devices (MODBUS RS232, Profibus, LONBus, etc.). Available at CS141L, CS141SC, CS141MINI & CS141R_2 = RS232 Available at CS141LM & CS141SCM =RS485 (not equipped CS141BL, CS141BSC) 3 LAN Port RJ 45 Ethernet 10/100 Mbit Interface with integrated status LEDs (green LED: Connection to network established, yellow LED: network traffic) 4 DC Input external device: supplied by a 12V switching adapter (delivered with the device) internal device: supplied via the slot interface of the device 5 AUX Equipped at CS141L, CS141LM, CS141SC and CS141SCM to connect CON_R_AUX4 and BACS etc. 6 Status LEDs (red / green) 7 Slide Switch DIP Switch 8 USB Operation Status CS141 Unpacking the operating system (update procedure) Error while unpacking the operating system Boot process of the operating system Communication to external device lost (e. g. UPS) Normal operation - connection to external device established For switching between different boot options. Slide Switch in the middle position / position OFF: To set the CS141 in the configuration mode and activated the default IP address after a cold start. Slide Switch in the right position / 1 position OFF + 2 position ON: DHCP Mode, the IP is set by the DHCP Server. Check the MAC address of your device to identify your device in the network. Slide Switch in the left position / 1 position ON + 2 position OFF: The network settings of the HTTP interface are used it is also possible to configure DHCP Mode. LED Notification red blinking red fast blinking red long on red and green green blinking Version:

2 English Installation/Network Integration of a CS Enabling of configuration mode Variant 1 1. Move the Slide Switch in the middle position / DIP SW 1 & 2 in the position OFF. Ethernet cross cable IP: Subnet: Gateway: Connect the LAN port of the CS141 directly with an Ethernet Cross Cable to the PC / workstation. Important: It is recommended to set the PC to the same network segment, for example AND for the Gateway Variant 2 1. Move the Slide Switch in the middle position / DIP SW 1 & 2 in the position OFF. 2. Connect the PC with a Switch or Hub and two Network Cables on the LAN port of the device. IP DIP Switch 1+2 = off Slide Switch middle IP DIP Switch 1+2 = off Slide Switch middle Ethernet cables Hub/Switch IP: <Your IP Address> Gateway: <Your Gateway> 2. Connect device to the UPS External Version Connect the UPS with the original UPS cable to the COM1 port of the CS141. Slot Version Put the device into the slot interface of the UPS. For the installation of the UPS, have a look into the User Manual which is part of the documentation CD or could be downloaded from the homepage of your UPS manufacturer. All UPS functions and the usage of flexible events etc. are described in the CS141 User Manual! 3. Connect the CS141 to the power supply External Version Connect the CS141 to the provided power supply. Slot Version The CS141 slot devices are supplied via the slot interface of the device. It is always possible to insert or remove the CS141 without damaging the UPS. To interrupt the power supply, remove the device from the slot and insert it again. Power Supply

3 4. Access to the CS141 over the network 4.1. Add the route of the standard IP address on your computer 1. Open the DOS Command Prompt or 2. execute cmd.exe 3. Enter the following command: route add <local IP Address> (for example: route add ) 4. Execute the command "ping " to check if the device is reachable. Advice: The CS141 needs approximately 30 seconds to start the webserver. If the webserver runs, the LED will changes from red (booting) to green and starts blinking Automatic search with the tool "Netfinder" The following link leads to the software "NetFinder" that search your device on the network automatically: install/netfinder.zip 5. Access via HTTP connection and login 1. Start a Browser 2. Enter the address 3. For the login choose the user name: admin Default password: cs141-snmp Note: Modern web browsers tend to cache files for later use. This browser behavior is often the cause of presentation and connection errors. In this case, delete the browser cache and press CTRL + F5. 6. Choose language 1. Choose the entry - System - General At the drop-down menu on the left side. 2. Choose the preferred Language.

4 English 7. Configure the IP address of the CS141 Basic Network Settings 1. Choose the entry - System - Network at the drop-down menu on the left side. 2. Enter the values for - Local Address - Subnet Mask - Default Gateway ("DNS-Server", if desired) 3. Press the button Apply to commit the changes. 4. Choose the entry - System - Date & Time in the drop-down menu. 5. Enter the IP Address of your timeserver and synchronize the CS141 with this server. The timeserver settings are important for the event- / alarm logging. (If no timeserver is configured the time will be set to :00). 6. The changes of each configuration page have to commit by pressing the button Apply. 7. Choose the point - Devices - UPS - Setup in the drop-down menu for the UPS configuration. 8. Choose the UPS Model, which is connected to the CS Click on the button Apply to save the changes. More Information about the UPS settings are available in the CS141 User Manual.

5 8. Connect the CS141 with the network Connect the LAN port of the device with a RJ45 network cable (not included) to the network. Network 9. Switch into the operation mode The CS141 is reachable on the IP address ! 1. For changing into the operating mode push the Slide Switch in the left position / DIP SW 1 in the position ON. 2. For Cold-Boot remove the power supply from the CS Connect the CS141 to the power supply again. The CS141 is reachable at the configured IP address. (The address isn't reachable anymore!) Power Supply 10. Sending shutdown signals to computers on the network For shutting down a computer in case of a power failure it is necessary to install an RCCMD client on it. Some configurations into the event management of the adapter have to be done, too. Installation of the RCCMD client 1. Download the setup file from the UPS- Management CD or from from the internet. 2. Each RCCMD installation requires a seperate license key. For some products, a license key is included. More licenses are available at your supplier. - Download - Software - RCCMD Download 3. In the first menu, you have to enter the IP address of the adapter whose shutdown signals should receive. Commit the following default configuration. Note the shutdown file in the last window. For editing the shutdown sequence of the client, press the button "configure" (It is also possible to edit the batch file to change or add events.) the installation finishes by pressing "install" and the service will start.

6 English 11. Event configuration for the CS Choose the entry - Devices - UPS - Events from the drop-down menu. 2. Click the Button + next to the event Powerfail. 3. The Job-Editor starts. Choose the option RCCMD Shutdown from the menu. 4. Enter the IP Address of your client (The Listener Port is usually 6003). At the right side you can specify when the shutdown signal is going to be released, for example At 300 seconds remaining time. 5. Click the button Save Configuration. 6. For security reasons it is recommended to make the same RCCMD shutdown entries at Powerfail for the Event Battery low - but here without any delays to avoid that the server crashes because of low battery alarm! 12. Options for the CS141 The CS141 can be a variety of environmental sensors and other measuring devices are combined, to temperature, humidity, fire and smoke, motion and intrusion, pressure, levels etc. to be monitored. In addition, other components such as various mounting brackets, BACnet Converter, PROFIBUS Converter etc. available. Please ask your UPS manufacturers / suppliers for more detailed information about the options available.