How to Recover the OS7030

Size: px

Start display at page:

Download "How to Recover the OS7030"

Jonah Griffith
5 years ago
Views:

1 How to Recover the OS7030 What you will need: - You will need to make up a serial cable to connect to the SIO connector inside the OS7030. PC serial port OS7030 SIO Connector 9 Pin D Sub Female connector 3 pin Female Molex connector 2.54mm FTP program (TFTPD32 or Pumpkin) - SW Package - Tera Term or Hyperterminal Recovery procedure 1. Unzip the SW package into C:\OS7030\Package Boot File 2. Install Tera Term and run the application. 3. Select the serial radio button and the com port on your PC. Page 1 of 7

4. Configure the serial port as below remembering

Power on the cabinet and immediately start

2 4. Configure the serial port as below remembering to select the com port on your PC. 5. Connect the SIO cable between PC and OS7030 SIO connector. 6. Power on the cabinet and immediately start pressing q until you see Hit Q or q key to stop autoboot you should now have the prompt Samsung > Page 2 of 7

3 See screen shot on next page. 7. To view the current boot file and ip addresses on the system enter printenv and enter. Samsung > printenv bootdelay=3 baudrate=38400 eth1addr=00:aa:bb:cc:dd:ff tftpdir=. mspname=ms30v521.pkg cspname=cs30t200.pkg irdname=dr30t200.pkg bootfile=bt30t200.bin (yours may be different) mtdboot=setenv bootargs console=ttys0,38400 root=/dev/ram0 init=/linuxrc rw init rd=0x ,3m rootfstype=squashfs mem=112m updateboot=tftp ${tftpdir}/${bootfile}; protect off 1:0-111;erase 1:0-11 1; cp.b ${fileaddr} ${filesize}; protect on 1:0-111 clearenv=protect off 1: ;erase 1: ;protect on 1: nanderaseall=nand erase clean updatecspnand=tftp fffe00 ${tftpdir}/${cspname}; nand erase ; nand wri te ${filesize} updatemspnand=tftp 1fffe00 ${tftpdir}/${mspname}; nand erase ; nan d write ${filesize} updateirdnand=tftp 2fffe00 ${tftpdir}/${irdname}; nand erase ; nan d write ${filesize} readcsp=nand read readmsp=nand read readird=nand read installrfs=setupgradeflag;run mtdboot; run updateirdnand; run readird;run readms p; loadmsp ; run readcsp; bootcomcerto install=setupgradeflag;run mtdboot; run updateirdnand; run updatecspnand; run up datemspnand; run readird;run readmsp;loadmsp ;run readcsp; bootcom certo standalone=clearupgradeflag;run mtdboot; run readird;run readmsp; loadmsp ;run readcsp; bootcomcerto bootcmd=run standalone ipaddr= (Your IP addresses will either be the default or if you have changed the IP gatewayip= addresses in mmc830 you will see what you have entered in mmc830) netmask= ethaddr=00:16:32:c7:44:a3 Page 3 of 7

4 serverip= scsp= smsp= sird=c00000 stdin=serial stdout=serial stderr=serial (The serverip will probably be the default setting and you will need to change this to the IP address you assign to your PC) Environment size: 1618/16380 bytes Samsung > 8. The default ip address for the system is and the serverip is If the ip addresses are still in default you can assign your pc the serverip address If you have the system on the customers network the ipaddr will most lickely have changed. Configure an IP address on your PC in the same range as the phone system. 10. Change the server IP address so it is the same as the IP address on your PC. The following commands can be used if you need to change any of the ip addresses. - Samsung > setenv ipaddr Samsung > setenv gatewayip Samsung > setenv serverip Samsung > setenv bootfile bt30t200.bin (you only need to include the bootfile when upgrading the bootfile via SIO). The bootfile name must be entered exactly as it appears in the SW package received from Samsung. - Samsung > saveenv (To save the settings) Saving Environment to Flash... Un-Protected 16 sectors Erasing Flash... Erasing 16 sectors... ok Erased 16 sectors Writing to Flash... ok done Protected 16 sectors Samsung > 11. Connect a network cable between your pc and OS7030. (you can use either a straight thru or crossover) 12. Run the TFTPD32 server Page 4 of 7

5 13. The Server interfaces ip address is the ip address on your PC and must be the same as the serverip address on the OS7030. Select settings 14. Browse to the folder where the SW package has been unzipped to. Page 5 of 7

15. Select ok Upgrading Bootrom thru SIO 16. Enter the following command Samsung > run updateboot;run clearenv;reset and enter. If no errors you will see ######## on screen.

6 15. Select ok Upgrading Bootrom thru SIO 16. Enter the following command Samsung > run updateboot;run clearenv;reset and enter. If no errors you will see ######## on screen. The bootrom upgrade takes about 10 seconds and then the system will restart. When the system restarts press the q key again to interrupt boot up mode so you are back at the prompt Samsung > Samsung > run updateboot;run clearenv;reset TFTP from server ; our IP address is Filename './bt30t200.bin'. Load address: 0x Loading: ######################################## done Page 6 of 7

7 Bytes transferred = (31f1c hex) Un-Protect Flash Sectors in Bank # 1 Erase Flash Sectors in Bank # 1 Erasing 112 sectors... ok Copy to Flash... ok done Protect Flash Sectors in Bank # 1 Un-Protect Flash Sectors in Bank # 1 Erase Flash Sectors in Bank # 1 Erasing 16 sectors... ok Protect Flash Sectors in Bank # 1 Resetting CPU Upgrading SW Package Steps 17 to 19 only need to be done when upgrading from V1.xx to V2.03 or above. 17. Samsung> setenv irdname dr30v204.pkg The irdname and cspname files must be 18. Samsung> setenv cspname cs30v204.pkg entered as they appear in the SW 19. Samsung> saveenv package you received. 20. Enter the following command Samsung > run nanderaseall and enter. Samsung > run nanderaseall NAND erase: device 0 offset 0, size nand_legacy_erase: dev_id=0x f, start=0, len= OK Samsung > 21. Enter the following command Samsung > run install and enter. If no errors you will see ####### on the screen. The upgrade takes about 15 minutes including boot up time. 22. Once the system is booted up goto mmc 727 and confirm the software version. 23. You will need to upload VM prompt file afterwards with either webmmc or IT Tool. The End Page 7 of 7

UPGRADING THE ARCTIC FIRMWARE

Viola Systems Ltd. tel +358-(0)201-226 226 Lemminkäisenkatu 14-18B fax +358-(0)201-226 220 FIN-20520, Turku e-mail support@violasystems.com Finland APPLICATION NOTE VA-09-5-2 UPGRADING THE ARCTIC FIRMWARE