Error Numbers of the Standard Function Block

Transcription

1 A.2.2 Numers of the Stndrd Funtion Blok evlution The result of the logi opertion RLO is set if n error ours while the stndrd funtion lok is eing proessed. This llows you to rnh to your own error evlution routine with the onditionl rnh SPB. Type of storge The stndrd funtion lok stores errors whih hve ourred in severl ples in the memory of the PLC s shown elow: In umultor 1, fter every ll of the stndrd funtion lok In DW n+3 of the DB-ZU dt lok (if one exists) In the jo milox of the DB-TDOP if the error is relted to jo The following tle shows the possile errors rrnged ording to the error numer nd the type of storge. s whih pply to SINEC L2 nd SINEC L2-DP re identified with n sterisk (*). Type of storge DB-TDOP DB-ZU (if present) Stndrd funtion lok Possile errors nd their tretment Aumultor 1 numer desription Cuse/remedy 1* DB-ZU: Invlid numer The DB-ZU numer trnsferred to umultor 1 must e in the 10 to 255 rnge. The high yte of the umultor my hve een onfused with the low yte. 2* DB-ZU: Does not exist The DB-ZU must e set up with length of t lest 16 words depending on the numer of TD/OP devies onneted. 3* DB-ZU: Too short The length of the DB-ZU dt lok is sed on the highest TD/OP numer speified, even if only one TD/OP devie is onneted. 4* TD/OP numer: Invlid The TD/OP numer trnsferred to umultor 1 must e in the 1 to 16 rnge. The high yte of the umultor my hve een onfused with the low yte. 5* No strtup took ple. Set the strtup it (D 64.0 in DB-TDOP) one. 6 Invlid CPU type Chek the type nd relese sttus of the CPU. 7* DB-TDOP = DB-ZU Speify nother numer for DB-TDOP. 10* TD/OP jo numer: Invlid The TD/OP devie sends internl PLC jos to the stndrd funtion lok (e.g. dte, time). This error mens tht the TD/OP devie hs sent n invlid jo numer. The relese sttus of the funtion lok does not mth tht of the firmwre. Communition User s Mnul A-17

2 numer desription Cuse/remedy 101* DB-TDOP: Invlid numer A DB-TDOP numer in the 10 to 255 rnge must e trnsferred to the stndrd funtion lok. 102* DB-TDOP: Does not exist The DB-TDOP dt lok must e set up. 103* DB-TDOP: Too short The dt lok must e set up with the required minimum length. 105 DB-TDOP: Invlid identifier 107* DB-ZU numer = DB-TDOP numer = DB-DHB numer The onneted TD/OP devie must store ertin identifier in dt word DW 30 of the DB-TDOP dt lok. The DB- TDOP numer onfigured on the TD/OP devie is prt of this identifier. The error messge ours when the DB-TDOP numer onfigured on the TD/OP devie does not mth the TD/OP numer speified in the stndrd funtion lok. The error n lso our riefly immeditely fter strtup euse the TD/OP devie hs not stored the identifier in the DB-TDOP yet. Ignore the error if this hppens. Renme one of the two dt loks DB-ZU or DB-TDOP (DB-DHB numer is fixed). 108* DB-DHB does not exist. The SINEC L1 onnetion requires tht the DB-DHB e onfigured s DB 56. The SINEC L2 onnetion requires tht the DB-DHB e onfigured s DB * DB-DHB too short The dt lok must e set up with length of 15 dt words (DW 0 to DW 14). 115 Life it monitor hs een triggered. 120* STBS: Invlid numer Vlid flg numers: 0 to * STBR: Invlid numer Vlid flg numers: 0 to 198 The onneted TD/OP devie hs not inverted its life it. Reson: There is no onnetion to the TD/OP devie or the stndrd funtion lok is lled too often in one yle. Inrese the vlue in the DB-TD/OP. 122* STBS = STBR Speify nother numer for one of the sttus ytes. 150 CP 521 SI, CP 523 is not yet redy. 151 CP 512 SI, CP 523, IM 308B: Invlid ddress 152 CP 521 SI, CP 523: Does not exist This error n our during the strtup efore the CP epts the onfigurtion dt. The ddress of the CP 521 SI, CP 523 or the IM 308B speified in the DB-ZU is invlid. Communitions proessor CP 521 SI, CP 523 is not instlled on the PLC or the ddress set on the CP 521 SI, CP 523 does not mth the one speified in the stndrd funtion lok. 153* Blok size invlid Vlid lok size: 8, 16, 32, 64, 120 or 240 ytes 154* Wrong IM numer Modify IM numer in DB-ZU. 155* Wrong TD/OP ddress TD/OP hving this ddress not ville; modify TD/OP ddress in DB-ZU. A-18 Communition User s Mnul

3 numer desription 156* IM308C not ommuniting with OP. 157* Wrong ddress of DP window Cuse/remedy IM308C not redy for opertion or is defetive Strt ddress of DP window in DB ZU not the sme s in the COM onfigurtion of IM308C. Strt ddress of DP window in DB-ZU not sme s in the COM onfigurtion of IM 308C. 158* Wrong field length The field length in the DB-ZU is different from tht of the COM onfigurtion of the IM308C 160* Reeive milox type numer invlid 161* Reeive milox DB/DX numer invlid 162* Reeive milox DB/DX offset invlid Permissile types: 0 = DB, 1 = DX (DX only for S5-115U with CPU 945, S5-135U nd S5-155U) The DB/DX numer must e in the rnge from 10 to 255. The offset must e in the rnge from 0 to 128 (for L2-DP: 0 to 215). 163* Send milox type invlid Permissile types: 0 = DB, 1 = DX (DX only for S5-115U with CPU 945, S5-135U nd S5-155U). 164* Send milox DB/DX numer invlid 165* Send milox DB/DX offset invlid 166 DX2 does not exist (only for SI2 of CPU 928B). 167 Coordintion ytes CBS nd CBR missing The DB/DX numer must e in the rnge from 10 to 255. The offset must e in the rnge from 0 to 128 (for L2-DP: 0 to 215). Set up DX2. The oordintion ytes must e loted in the DB-TDOP (see DX2 onfigurtion for SI2 of CPU 928B). 168 ASCII driver missing The strtup my not hve een performed. 169 ASCII driver not enled The strtup my not hve een performed. 170* Aknowledgment of PLC jo reeived without PLC jo eing tive The sttus of jo ws overwritten y the user. 171 Messge identifier unknown The TD/OP sent n undefined jo, or trnsfer error ourred. 172 Jo numer invlid The TD/OP sent jo with n unknown jo numer. 180 Trnsfer error Undefined sttus of the oordintion yte CBR. 181 Prity error Compre the prities set for S5 nd TD/OP, nd set oth to the sme prity (SI2 of CPU 944 prity: even). 183 Input uffer full The TD/OP is sending too fst for the PLC yle. Messges re eing lost. Cll the funtion lok more frequently during the yle or optimize the TD/OP onfigurtion. 184 Too mny messges See error no Messge lrger thn reeiving milox 186 Reeive milox does not exist The messge length is usully limited to 88 ytes y the TD/ OP. The hrter dely time etween two messges my not hve een deteted ==> trnsfer error. The onfigured dt re does not exist, or strtup ws not performed fter hnges. Communition User s Mnul A-19

4 numer desription Cuse/remedy 187 Messge too long See error no Brek The onnetion is roken. The le is defetive or not onneted. 189* Reeive milox DB/DX too short Compre the pointer speified for the reeiving milox (offset + length) with the dt re tully present. 190* Trnsfer error Undefined sttus of the oordintion yte CBS. 191* Output uffer full 192 Configurtion error Chek the speifitions in DB-ZU onerning the send/ reeive milox nd the hrter dely time. 193 Send milox does not exist The onfigured dt re does not exist or strtup ws not performed fter hnges. 194 Messge too long The hrter dely time etween two messges ws not deteted ==> trnsfer error. 199* Send milox DB/DX too short 200 Communition error in system progrm (only for SI2 of CPU 928B) Compre the pointer speified for the send milox (offset + length) with the dt re tully present. Chek the stti prmeter set for SI2. 201* DB-APP: Invlid numer The pointer to PLC jo ontins n invlid DB numer. Only DB numers from 10 to 255 re permitted. 202* DB-APP: Does not exist The pointer to PLC jo points to non-existent DB dt lok. Set up the DB dt lok. 203* DB-APP: Too short The pointer to PLC jo points to DB dt lok. The PLC jo is loted either prtilly or ompletely outside the dt lok. Selet the strt ddress of the pointer so tht the 4-word PLC jo fits into the dt lok ompletely. 206 DX-APP: Invlid numer The pointer to PLC jo ontins n invlid DX numer. Only DB numers from 10 to 255 re permitted. 207 DX-APP: Does not exist The pointer to PLC jo points to non-existent DX dt lok. Set up the DX dt lok. 208 DX-APP: Too short The pointer to PLC jo points to DX dt lok. The PLC jo is loted either prtilly or ompletely outside the dt lok. Selet the strt ddress of the pointer so tht the 4-word PLC jo fits into the dt lok ompletely. 209* TIMER-APP: Address not permitted 210* COUNTER-APP: Address not permitted The pointer of TD/OP jo points to timer re. The vlid strt ddresses re dependent on the CPU. Chek the TD/OP onfigurtion. The pointer of TD/OP jo points to ounter re. The vlid strt ddresses re dependent on the CPU. Chek the TD/OP onfigurtion. 211 F-APP: Invlid ddress The pointer to PLC jo points to the flg re. The PLC jo nnot e (even prtilly) loted in the srth flg re. Vlid strt ddresses re loted in the rnge from 0 to * S-APP: Invlid ddress The pointer to the PLC jo points to the extended srth flg re. Vlid strt ddresses re dependent on the CPU nd re loted in the rnge from 0 to A-20 Communition User s Mnul

5 numer desription Cuse/remedy 213* EB-APP: Invlid ddress Vlid strt ddresses: 0 to * AB-APP: Invlid ddress Vlid strt ddresses: 0 to * TD/OP devie is OFFLINE The onnetion to the onneted TD/OP devie ws disrupted nd PLC jos nnot e sent t present. This error n lso our riefly immeditely fter strtup. Ignore the error if this hppens. 216* L2-DP onnetion nnot e set up I/O ddress re speified inorretly in the DB-ZU TD/OP not onneted (hek the BF LED on the IM 308B.) 219* Invlid PLC jo with prllel onnetion only. The jo identifier must e in the rnge from 30 H to 36 H. 220* Numer of vriles greter thn 31 The numer of vriles in n lrm or event messge must not exeed * Pointer: Invlid type The jo milox ontins n inorret dt type s pointer to PLC jo. Only dt types 0 to 3 re permitted. Only dt types 0 to 7 re permitted for pointers to TD/OP jo. 222* Pointer: Type on DX invlid The extended DX dt loks re only permitted with PLCs 115U with CPU 945, 135U nd 155U. 223* Pointer type to S flg invlid The extended flg re is only permitted with PLCs 135U nd 155U1 (PAFE no. in DR 102 of DB-TDOP). 246* PAFE error PAFE error in the CONTROL, SEND or RECEIVE dt hndling lok 247* SEND terminted with error The send jo ws terminted with errors. The inditor word (ANZW1) is now ville to the user in dt word 101 of the interfe dt lok DB-TDOP. STBS/STBR error A send/reeive jo ws terminted with errors (S5-95 L2 only). 248* Connetion sttus 01h: Interfe error 1) 249* Connetion sttus 02h: Devie not ville 1) 250* Connetion sttus 03h: Servie not tivted 1) 251* Connetion sttus 10h: Servie on lol SAP not tivted 1) 252* Connetion sttus 11h: No retion from sttion 1) 253* Connetion sttus 12h: Bus line is disonneted 1) 254* Connetion sttus 15h: Invlid prmeter in heder 1) 255 TD/OP error The onneted TD/OP devie hs reported n error. The TD/ OP error numer is stored in DW m+3 of the jo milox. 1) on SINEC L2 us: See SINEC L2 Equipment Mnul for mening of onnetion sttus. Only SDA servies re used for the TD/OP PLC onnetion. Communition User s Mnul A-21