service code Code: 2013 Language

Transcription

1 service code Code: 2013 Language

2 1. Service menu code 1. Service menu code Control times can only be altered in the service menu. The code for this is Service level A range of queries can be run at service level, including the configuration of settings. To reach the service level, select the menu point Service menu by pressing and at operator level. Access the service menu by repeatedly pressing the button. The following appears: service code Pressing again brings up the prompt to enter the code. Code: _ The 4-digit code can be entered using the arrow keys. Press the button to confirm this entry. The following appears: Basic setup The individual menu points and their meaning are displayed below: Menu point Basic setup Duration period Number of cycles Starting times Cycle restart Clear logbook Languages Meaning Pre-programmed basic setup with set cycle times Cycle T1-12, Cycle pause T13,14 Holiday mode T15,16 Maximum 24 cycles Times for cycle start e.g.: 07:00, 19:00 Program is restarted with current settings Operating hours meter and Old faults are deleted Various languages can be selected 2.1 Basic setup selection After successful login, the menu point Basic setup appears on the screen. Access the selection of programmed basic setups by repeatedly pressing the button. 2 / 8

3 2. Service level one2clean 4EW C The stored basic setups are retrieved one after the other using the arrow keys. The desired basic setup is confirmed with, then the successful selection is confirmed with a 2-second display of OK. 2.2 Duration period From the menu point Basic setup press the arrow key. Duration period appears on the screen. Press button. The following appears on the screen e.g.: T1: X min By pressing the button the individual duration periods of the current configured basic setup are retrieved one after the other. The number can be increased (+1) starting with the last digit using the arrow key. The number can be decreased (-1) starting with the last digit using the arrow key. In addition to the configured duration period of a cleaning cycle, the menu point Duration period contains the sums of the actual duration periods (T17 to T19). Thus these duration periods add up the corresponding duration periods and give the operator an overview of the selected settings (e.g. overview of the run time of the compressor: T19). 2.3 Number of cycles From the menu point Duration period press the arrow key. Number of cycles appears on the screen. Press Cycles 2 The number of cycles per day can be increased (+1) starting with the last digit using the arrow key. The number can be decreased (-1) starting with the last digit using the arrow key. The selected number is stored using the display. button. The display then jumps from the menu back to the Number of cycles 2.4 Starting times From the menu point Number of cycles press the arrow key. Starting times appears on the screen. Press the Cycle1: HH:MM 3 / 8

4 2. Service level The number can be increased (+1) starting with the last digit of the seconds display using the arrow key. The number can be decreased (-1) starting with the last digit of the seconds display using the arrow key. The number is stored using the button. The seconds are set analogous to the minutes. The number is stored using the cycles display. button. The display then jumps from the menu back to the Number of 2.5 Perform cycle restart From the menu point Starting times press the arrow key. Cycle restart appears on the screen. Press the Press the ^ arrow Pressing the button restarts the programme with the current settings. All users are disabled once the cycle reset is activated. The control system goes directly to cycle pause (T13/T14). A new cleaning cycle starts when the next starting time begins. 2.6 Clear logbook From the menu point Operating hours press the arrow key. Clear logbook appears on the screen. Press the Press the ^ arrow Pressing the button will delete all fault messages and all operating hours. OK is displayed on the screen whilst the control system performs the deletion. The screen then jumps to the display Empty logbook. All current operating hour meters, cycle meters and the logbook are deleted. 2.7 Select language From the menu point Clear logbook press the arrow key. Languages appears on the screen. Press the English 4 / 8

5 2. Service level The desired language can be selected using the arrow keys. The selection is confirmed using the button. The screen then switches back to the Languages display. The menu navigation is immediately displayed in the selected language. Programmed languages are: German, English, French, Italian, Norwegian, Polish, Swedish, Spanish, Slovenian, Romanian, Czech. 5 / 8

6 3. Table values 3. Table values compressor Tacts Description Valve 3 PE 3 PE D 5 PE 5 PE D 7 PE 7 PE D 9 PE 9 PE D 10 PE 10 PE D 12 PE 12 PE D 14 PE 14 PE D 15 PE 15 PE D 20 PE T 1 [min] Deni T 2 [sec] on on T 3 [min] off off T 4 [min] aeration T 5 [min] on on T 6 [min] off off T 7 [min] sedimentation T 10 [min] discharging on T 13 [min] cycle break - on on T 14 [min] cycle break - off off T17 [min] cycle time (control function) [min] T18 [h/d] complete time of aeration [h/d] 5,6 7,0 5,6 7,0 5,6 8,4 7,0 8,4 7,0 8,4 7,0 8,4 7,0 8,4 7,0 8,4 7,0 T19 [h/d] complete runtime [h/d] 5,9 7,5 6,0 7,6 6,1 9,0 7,5 9,1 7,6 9,2 7,7 9,2 7,7 9,3 7,7 9,3 7,8 No. of cycles: 2 starting time: 07:00 19:00 6 / 8

7 4. Compressor data sheet 4. Compressor data sheet 7 / 8

8