HomeWorks Manual Override Setup Guide Revision C 01/16
|
|
- Abel Augustine Bridges
- 6 years ago
- Views:
Transcription
1 HomeWorks Setup Guide Revision C 01/16 HomeWorks Fail-Safe Operation using Rev C Page 1
2 Table of Contents Overview... 3 What is?... 3 How does it work?... 3 Best Practices... 3 How many mechanical switches or PowPaks are needed?... 3 Basic Switch Solution:... 4 PowPak Solution:... 5 HomeWorks QS Software Design Tab:... 6 HomeWorks Illumination Software Load Schedule:... 7 HomeWorks Fail-Safe Operation using Rev C Page 2
3 Overview What is? In the unlikely event that the Processor(s) are disabled, the Keypads will no longer communicate with the system. Local controls, such as wireless or wired Maestro dimmers, will still allow control. Grafik Eye will also allow local control of the lighting zones. A manual override is provided for systems employing a centralized topology with panel mounted Remote Power Modules (RPM) where Keypads are the only source of local control. The homeowner can utilize the manual override feature to turn all RPM lighting zones to a preset level which is programmed using the HomeWorks software utility. How does it work? Manual override requires an auxiliary switch or contact closure output (CCO) to the Manual Override terminal blocks. The particular MI (or group of MIs) will go into manual override mode when the contact closure completes the circuit. A manual override switch or CCO will need to be installed at the commissioning stage of a job in order to take full advantage of the feature in the MI. This switch/cco would typically be located in the panel room or closet and should be clearly labeled. We will also discuss an alternative solution utilizing a PowPak Relay Module with CCO and Pico keypad. Best Practices It is recommended to deploy one mechanical switch for each panel. One switch can be used to control multiple panels in what is considered a parallel configuration, however all panels will be controlled together. Individual control is ideal because it allows the end user to turn on only the necessary lighting. Mechanical switches should also be installed in a location that is easily accessible to the homeowner but not in an area where guests could trigger unnecessary usage of the feature during normal operation, such as a closet close to an egress area. This solution is ideal for new construction. One manual override switch is recommended per floor of the living space. For retrofit applications, convenient control can be provided via a PowPak Relay Module with CCO (RMJ-5RCC01-DV-B) paired with a Pico keypad (PJ2-2B). The Relay Module is used in place of the mechanical switch, mounted near the panel. The associated Pico can be remotely mounted in the above recommended locations. These products utilize patented Clear Connect RF technology to provide reliable communication providing the flexibility to place the Pico in a more convenient location (within 30 feet of the PowPak Module). For more information on the PowPak solution, please refer to the PowPak Relay Module Installation sheet found at Note that it is best practice to still install a mechanical switch near the panel in addition to the PowPak, both controlling the same MI(s) manual override. How many mechanical switches or PowPaks are needed? Single - One switch or PowPak would be wired to each individual MI s terminal Parallel One switch or PowPak can control multiple MIs that are daisy chained together via their terminals Refer to the Wiring Diagrams for switch and wire ratings. HomeWorks Fail-Safe Operation using Rev C Page 3
4 Basic Switch Solution: Single MI (PC Board View) Processor Communication Link Interactive Link 1 Illumination Link 1 QS - Configurable Additional Mis (Parallel Configuration, Optional) Diagnostic LEDs Mechanical Override Switch + Terminal - Terminal Terminal Wire Run Length Less than 1,000ft Greater than 1,000ft Wire Gauge 16 to 24 AWG 16 to 18 AWG Switch(es) should be rated for 50 milliamps at 24VDC or greater. In parallel configurations, where one switch controls multiple MIs, the switch must be rated to handle the sum total current of all MIs. For example, 6 MIs would be a total of 300 milliamps. HomeWorks Fail-Safe Operation using Rev C Page 4
5 PowPak Solution: Single MI (PC Board View) Processor Communication Link Interactive Link 1 Illumination Link 1 QS - Configurable Additional Mis (Parallel Configuration, Optional) Diagnostic LEDs PowPak CCO Module (RMJ-5RCCO1-DV-B) Note: For installation instructions, please refer to the PowPak Relay Module Installation Sheet at COM NO + Terminal - Terminal Pico Wireless Keypad (PJ-2B) Terminal Wire Run Length Less than 1,000ft Greater than 1,000ft Wire Gauge 16 to 24 AWG 16 to 18 AWG The CCOs of the PowPak are rated for a total of 1 amp at 24VDC. In parallel configurations, where one CCO controls multiple MIs, the CCO can handle the maximum 16 MIs (0.8 amps). HomeWorks Fail-Safe Operation using Rev C Page 5
6 HomeWorks QS Software Design Tab: 1. Under the Design tab select the loads option from the drop-down menu. 2. Select the Customize Columns at the top of the Load Schedule screen. 3. Select the opition 4. Change the settings to desired level. By default all zones will be 100%/On. Notes: 1. Non-essential zones (laundry, closets, etc.) should be off. 2. Emergency pathways should be created with 75% or higher zone levels. 3. Bedroom spaces should be a dimmed value such as 50% or less. HomeWorks Fail-Safe Operation using Rev C Page 6
7 HomeWorks Illumination Software Load Schedule: 1. Select the Load Schedule screen at the top as indicated 2. Highlight the zone you would like to change 3. Change the zone value to the desired level. By default all zones will be set to 100%/On. Notes: 4. Non-essential zones (laundry, closets, etc.) should be off. 5. Emergency pathways should be created with 75% or higher zone levels. 6. Bedroom spaces should be a dimmed value such as 50% or less. Contact Lutron: Lutron Electonics Co, Inc Suter Road Coopersburg, PA U.S.A. Technical Support: hwsupport@lutron.com HomeWorks Fail-Safe Operation using Rev C Page 7
Using HWQS to Control DMX Outputs Revision A
Using HWQS to Control DMX Outputs Revision A Using HWQS to Control DMX Outputs Page 1 Table of Contents Overview... 3 Concepts and Definitions... 3 Scenario 1: Unique DMX Universes with Less Than 32 Channels
More informationSystem Comparison. Caséta, RA2 Select, RadioRA 2, & HomeWorks QS
System Comparison Caséta, RA2 Select, RadioRA 2, & HomeWorks QS Table of Contents Overview... 2 Caséta Wireless System Capacities... 3 Wireless Link Specifications... 3 RA2 Select System Capacities...
More informationIntegrating LaunchPort AM.2 Sleeve Buttons w/ Lutron Systems 1.0 Overview
Integrating LaunchPort AM.2 Sleeve Buttons w/ Lutron Systems 1.0 Overview The LaunchPort, from Dana Innovations, consists of a Station and a Sleeve that allows the user to mount and charge an ipad anywhere
More informationApplication Note #658 Revision B January 2018 Programming Residential Systems with Lutron LED Drivers
Application Note #658 Revision B January 2018 Programming Residential Systems with Lutron LED Drivers Overview Lutron LED drivers deliver smooth, flicker-free, continuous, high-performance dimming with
More informationYes Additional interface boards may be required.
Revision E February 2017 Solutions for Upgrading from HomeWorks Illumination to HomeWorks QS The following guide has been developed to assist those interested in upgrading an existing HomeWorks Illumination
More informationLutron Residential and Commercial Systems Rules
Lutron Residential and Commercial Rules 369821i 1 09.11.17 This document is meant to be a collection point for the rules that apply to different Lutron systems. This document is not meant to be an individual
More informationInstallation Instructions
H Installation Instructions Danger - Locate and lock supply breaker in the OFF position before installing processor assembly. 1. Install processor in the enclosure: The HomeWorks 8 Series is attached to
More informationApplication Note #625 Revision A January Integrating a Sonos System with RadioRA 2 and HomeWorks QS Systems. Overview
Revision A January 2017 Integrating a Sonos System with RadioRA 2 and HomeWorks QS Systems Overview The Lutron Connect platform integrates with Sonos systems allowing the Lutron system to seamlessly blend
More informationmanual setup guide a step-by-step guide for manually setting up a complete Lutron RadioRAR 2 wireless control system
start here manual setup guide a step-by-step guide for manually setting up a complete Lutron RadioRAR 2 wireless control system please leave this setup guide with owner Lutron Technical Support Hotline
More informationApplication Note #712 Revision A January T-Series OEM Solutions. 1. Configuration. Configuration Setup. 1 Customer Assistance
T-Series OEM Solutions Application Note #712 Revision A January 2019 T-Series LED Drivers provide a high-performance tunable white solution. The following document describes how to easily configure, control,
More informationUL Listed Retrofit Solution for Savant-LiteTouch Systems 1.0 Overview
UL Listed Retrofit Solution for Savant-LiteTouch Systems 1.0 Overview This application note demonstrates a retrofit solution for centralized Savant/LiteTouch Lighting systems involving a HomeWorks QS system.
More informationApplication Note #586 Revision C February 2017 Design and Programming for HomeWorks Illumination to HomeWorks QS Upgrades
Revision C February 2017 Design and Programming for HomeWorks Illumination to HomeWorks QS Upgrades 1.0 Overview HomeWorks QS provides the end user with the latest innovations in electric and natural light
More informationHi-lume Premier 0.1% EcoSystem LED Driver
Hi-lume Premier 0.1% EcoSystem LED Driver s provide a high performance solution for any space, in any application. They provide smooth, continuous dimming down to 0.1% of full output current, and fade
More informationHomeWorks QS Processor
product specifications 369-376 The processor provides control and communication to system components. The Ethernet links allow communication to the software, integration with third party systems and communication
More informationNEW Sivoia QS Wireless. product overview
NEW Sivoia QS Wireless product overview Sivoia QS Wireless introduction Sivoia QS Wireless product family Sivoia QS Wireless family Sivoia QS Wireless offers ultra-quiet, precision control of the full
More informationLQSE-4S8-120-D. 120 V~ 50 / 60 Hz 16 A. lutron.com LQSE-4S8-120-D. Dimming Power Module. Option. Input. Opt Def H M
Input Entrada Entrée Ta > 70 C Prog Option 120 V~ Def 50 / 60 Hz Opt1 10 A Opt2 Opt3 lutron.com H Switching Power odule Switching Power odule 3691060b 1 05.25.18 The DI Power odule (DP) family is a group
More informationPico 4-Button Wireless Remote
Pico 4-Button Wireless Remote The Pico wireless remote is a flexible and easy to use device that allows the user to control Lutron wireless load-control devices from anywhere in the space. This battery-operated
More informationLUT-DMX DMX512 Control Interface
rev dmx-1a 7.20.00 DMX512 Control Interface Lets GRAFIK Eye lighting controls operate lighting and other equipment that uses the DMX512 protocol: Strobes, fiber optic lighting, and LED-based lamps Fogger
More informationApplication Note #586 Revision D February 2018 Design and Programming for HomeWorks Illumination to HomeWorks QS Upgrades
Revision D February 2018 Design and Programming for HomeWorks Illumination to HomeWorks QS Upgrades 1.0 Overview HomeWorks QS provides the end user with the latest innovations in electric and natural light
More informationPico 4-Button Wireless Remote
Pico 4-Button Wireless Remote The Pico wireless remote is a flexible and easy to use device that allows the user to control Lutron wireless load-control devices from anywhere in the space. This battery-operated
More informationQS Link power supply. Lutron QS. Link Power Supply
086-108 1 02.05.09 QS Link power supply The QS Link power supply (QSPS-P1-1-50/ QSPS-P2-1-50/ QSPS-P3-1-50) is a 24 V plug in power supply that is used with Lutron QS lighting or shading devices. The Link
More informationHi-lume A-Series Driver Overview EcoSystem or 3-wire control
Hi-lume A-Series Driver Overview EcoSystem or 3-wire control 369-325 Rev. D 1 10.12.11 Hi-lume A-Series Driver is a high-performance LED driver that provides smooth, continuous 1% dimming for virtually
More informationHi-lume 1% EcoSystem Constant-Voltage 24 V- LED Driver with Soft-on, Fade-to-Black Dimming Technology
50016452a Dimming Driver Hi-lume 1% EcoSystem Constant-Voltage 24 V- Driver with Soft-on, Fade-to-Black Dimming Technology The CE-rated Hi-lume 1% Constant-Voltage Driver (LDE1) is a high-performance driver
More informationUL Listed Hi-lume A-Series Constant Voltage Driver Overview
UL Listed Hi-lume A-Series Constant Voltage Driver Overview 369789b 04.9.04 The UL Listed Hi-lume A-Series Constant Voltage Driver is a high performance LED driver that provides smooth, continuous % dimming
More informationPico Wireless Remote with Nightlight (for North, Central, and South America)
Pico Wireless Remote with Nightlight (for North, Central, and South America) 369760d 1 10.22.15 The Pico wireless remote with nightlight is a flexible and easy to use device that allows the user to control
More informationWallbox Power Module. 4/8 Series Remote Dimming Controls Grafik Eye /WPM Link N/A INTRODUCTION SPECIFICATION & DESIGN FRONT ROOM BACK ROOM APPENDIX
Wallbox Power Module 4/8 Series Remote Dimming Controls Grafik Eye /WPM Link N/A W a l l b o x P o w e r M o d u l e (hwi-wpm-6d-120) HomeWorks Wallbox Power Modules (WPM) control six independent zones
More informationPJ24BWHL21P Pico Pro 4B 2 Group Light. Features. Material, Color, and Finish. Dimensions and Weight. Descriptions. Manufacturer Information
3804 South Street 75964-763, TX Nacogdoches Phone: 936-569-794 Fax: 936-560-4685 Lutron Catalog Number Manufacturer Description Weight per unit Product Category Features actuator connection Frequency Range
More informationPower Boosters and 120 V Interfaces
Power Boosters and Interfaces 4/8/ Wireless Series Power Interfaces N/A N/A Power Boosters and Interfaces work with specific load types and/or increase the zone capacity of Wired Vareo Local Lighting Controls,
More informationVive HJS-0, HJS-1, HJS-2 Wireless Hub. Vive Hub
Vive Wireless Hub The Vive hub provides a connection point for Lutron Vive devices such as PowPak wireless dimming and switching modules, PowPak Wireless Fixture Controllers, PowPak 20 A Relay Modules,
More informationQSE-CI-NWK-E Control Interface
Control Interface 369373 Rev. A 1 12.16.10 Description The is a versatile integration access point for Lutron s QS-based systems. Through either RS232 or TCP/IP over Ethernet, third-party devices can control
More informationSystem Overview. myroom
System Overview 3691020a 1 01.30.17 The myroom Vue is a front-end software dashboard for the facility manager (user) to monitor and control myroom Plus guestroom systems. A powerful and easy-to-use web-based
More informationPowPak Single Zone Control Module with EcoSystem
PowPak Single Zone Control Module with EcoSystem The PowPak Single Zone Control Module with EcoSystem is a radio frequency (RF) control that operates up to 32 EcoSystem LED drivers or fluorescent ballasts
More information10-Output Configurable Smart Panel
10-Output The 10-Output simplifies wiring and organizes installations with multiple Sivoia QS window treatments and other system devices and interfaces. 085593a 1 11.02.17 WIN-PS-5CC-R The 10-Output is
More informationLutron. integration protocol
Lutron integration protocol revision G 5 March 2011 Table of Contents About Integration Integration s 4 Characters 4 Command Types 4 Command Structure 4 Command Termination 4 Command Examples 5 Integration
More informationPico Wireless Control (for North, Central, and South America)
Pico Wireless Control (for North, Central, and South America) 369612l 1 09.25.17 The Pico wireless control is a flexible and easy to use device that allows the user to control Lutron wireless load-control
More informationQSNE-2DAL-D Energi Savr Node QSTM 20 V. DALI Loop 2. seetouch QS Wallstation Energi Savr Node QS. QS Control Link
LUTRON R Node TM NE-2DAL-D Fixture Controller NE-2DAL-D 09.0.09 Node TM The Node is a DIN-rail mounted controller for -compliant Digital Addressable loads. It provides bus power and control for two independent
More informationApplication Note #97 Revision G February 2015 Lightning / Surge Protection for RadioRA 2, HomeWorks QS, and HomeWorks Devices
Revision G February 2015 Lightning / Protection for RadioRA 2, HomeWorks QS, and HomeWorks Devices Table of Contents Overview... 2 Recommendations... 3 Protection Equipment... 4 Breaker Panel Protection...
More informationGR 2400 PLANNING GUIDE. Important Note:
GR 2400 PLANNING GUIDE [ NEW CONSTRUCTION ] Planning Guide Index The Bus File................................... 2 Single Line Drawings.......................... 3 Multi-Bus Systems.............................
More informationEnergi Savr NodeTM QSN-2ECO-PS120 EcoSystem with Shades ESN a
085-255a 1 08.26.10 with shades Energi Savr Node The with Shades Energi Savr Node (ESN) (QSN 2ECO-PS120) is an integrated lights and shades panel. This document describes the with Shades ESN, which can
More informationPico Wireless Control (for North, Central, and South America)
Pico Wireless Control (for North, Central, and South America) 369612i 1 02.28.17 The Pico wireless control is a flexible and easy to use device that allows the user to control Lutron wireless load-control
More informationGRX-3000 Control Units
PRESET DIMMING CTROLS GRX-000 Control Units GRX-000 Control Units DESCRIPTI Cover (shown open) Base Zone Provide pushbutton recall of four preset lighting scenes. Control virtually any light source. Provide
More informationApplication Note #234 Revision A August Using a Ten Volt Module (TVM) Kit to Control LED and Fluorescent Fixtures. What is a TVM Kit?
Using a Ten Volt Module (TVM) Kit to Control LED and Fluorescent Fixtures Application Note #234 Revision A August 2008 What is a TVM Kit? A Ten Volt Module (TVM) kit, part number HW-TVMKIT-YYY is a box
More informationGRAFIK Eye QS Wireless
Open Preset Close Meeting Video Conference A/V Off GRAFIK Eye QS Wireless Customisable preset light, blind, and energy control Photography Nic Lehoux What is GRAFIK Eye QS Wireless? GRAFIK Eye QS Wireless
More informationPico Wireless Control (for North, Central, and South America)
Pico Wireless Control (for North, Central, and South America) 369612h 1 01.12.16 The Pico wireless control is a flexible and easy to use device that allows the user to control Lutron wireless load-control
More informationRA2 Select. Whole home lighting control made simple. Lutron.com/ra2select. Lutron Electronics Co., Inc Suter Road Coopersburg, PA
RA2 Select HomeKit requires an iphone, ipad, or ipod touch with ios 8.1 or later. The main repeater enables RA2 Select components to work with HomeKit technology. Controlling HomeKit-enabled accessories
More informationConverging Systems Inc.
Converging Systems Inc. e-node Lutron e-node Interfacing with Lutron Guide Version 1.02 Revision History Date Version Description Author 10/01/2012 1.0 Consolidated Version AD 10/10/2012 1.01 Enhancements
More informationWallstations for use with Grafik 3000 and 4000 Series Systems
Wallstations for use with Grafik 000 and 000 Series Systems NTGRX-LB NTGRX-LB-R/L NTGRX-LB9 NTGRX-LB9-R/L NTGRX-KP NTGRX-KP0 NTGRX-KP 7 8 9 Wallstation circuits are classified as Class circuits (U.S.A.)
More informationHomeWorks Remote Power Feed-Through Panels
power feed-through panels are available in two different sizes, each of which may be either surface-mounted or recess-mounted, in an electrical closet or other equipment room. The number of remote power
More informationWireless remotes Pico wireless controls
1.28 in (33 mm) 2.60 in (66 mm).31 in (8 mm) profile Shown actual size: Pico in White (PJ-3BRL-GWG-T01) Product family features Wirelesss master control from any location Requires compatible receiving
More informationBack Room Equipment INTRODUCTION SPECIFICATION & DESIGN FRONT ROOM BACK ROOM APPENDIX
Back Room Equipment http://resi.lutron.com Technical Support: product@lutron.com 89 P5 Processors HomeWorks processors comprise the major communication hub of a HomeWorks system. Each processor has communication
More informationQuantumR Light Management Hub
Quantum 369375e 1 04.02.2015 QuantumR Light Management Hub The Quantum light management hub provides a centralized connection point for Lutron EcoSystem digital ballast modules, Lutron power panels, GRAFIK
More informationEcoSystem to 0 10 V- Interface
to Interface to Interface 369537i 1 03.22.19 The to Interface provides a control gateway from an link to a compatible lighting device, typically an ED driver. It allows for individual addressing of the
More informationNodes, Wall Switches, Sensors & Peripherals Data Sheet
Nodes, Wall Switches, Sensors & Peripherals Data Sheet The Platformatics solution of Power over Ethernet (PoE) LED lights enables users to quickly, safely and easily move lights, adjust color temperature
More informationHLC. Omnistat2. Technical Sheet. Elegant, Reliable Lighting Control at an Affordable Price! 1
Omnistat2 HLC Technical Sheet Elegant, Reliable Lighting Control at an Affordable Price! Dim lights as movie begins, using the convenient remote control. Lighting control can enhance the enjoyment and
More informationPico Wireless Control and Mounting Accessories (for regions other than North, Central, and South America)
Pico Wireless Control and Mounting Accessories (for regions other than North, Central, and South America) The Pico wireless control is a flexible and easy to use device that allows the user to control
More informationConverging Systems Inc.
Converging Systems Inc. e-node Lutron e-node Interfacing with Lutron Guide Version 1.01 Revision History Date Version Description Author 10/01/2012 1.0 Consolidated Version AD 10/10/2012 1.01 Enhancements
More informationSuprex RS-485 SPX-7500 Wired Reader-Extender
Suprex RS-485 SPX-7500 Wired Reader-Extender Product Manual SPX-7500_MAN_181206 Cypress Integration Solutions 35 Years of Access Control Ingenuity CypressIntegration.com 2018 Cypress Computer Systems 1778
More informationDC Blue Series MLV. Requires Aion LED brand lighting fixture and approved dimmer or switch. Sold separately, not included DRIVER DC BLUE
Refer to the MOUNTING AND INSTALLATION INSTRUCTIONS Included with this unit. For Grounding Conductor, Use 18AWG minimum. CODE 03/13/14 Refer to the MOUNTING AND INSTALLATION INSTRUCTIONS Included with
More informationUsing the LR-HVAC-230-S Thermostat w/ HomeWorks QS
Using the LR-HVAC-230-S Thermostat w/ HomeWorks QS 1.0 Overview Fan coil unit (FCU), split system, and radiant floor systems are commonly used for Heating, Ventilation, and Air Conditioning (HVAC). With
More informationTRULINE 1A ORDERING CODES
Drywall Drywall with Plaster & Paint Description: TruLine 1A creates glare-free architectural lighting accents within 5/8" drywall. The 24VDC linear LED system features a shallow, 5/8" deep plaster-in
More informationHomeWorks QS Visor Controls
The HomeWorks QS Visor Controls allow lights, shades / draperies, and other equipment to be controlled from the car with just a touch of a button on a Visor Control Transmitter or a HomeLink compatible
More informationTaxonomies, Classifications, and Categories Residential dimmers, motion sensors, controls, & photo cells Wireless remote control
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 Lutron Catalog Number Manufacturer Description Weight per unit Product Category Features Frequency Range Material Material,
More informationHomeWorks B & O Keypads. Installation Instructions Please Read Before Installing. Overview. Important Notes
Installation Instructions Please Read Before Installing Overview The HWBO-8SE-IR, HWBO-4SE-IR, and HWBO-4SE-M are for use with HomeWorks systems. The keypad buttons are programmed using the HomeWorks Utility.
More informationRF Wireless LED Remote Dimmer Controller Model: DIM Two Colors Dimmer / 6 Zones / 6 Options to save
RF Wireless LED Remote Dimmer Controller Model: DIM 700 1001 Two Colors Dimmer / 6 Zones / 6 Options to save 20725 NE. 16 AVE. #A-33 MIAMI, FLORIDA 33179 TEL: (305) 652-2599 FAX: (305) 650-8812 WWW.LUMIRON.COM
More informationCaseta Wireless Pico Remote Control, 3-Button With Raise/Lower, Light Icons In White
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 Lutron Catalog Number Manufacturer Description Weight per unit Product Category Features body Frequency Range indicator
More informationDMX CONTROL SUPPORT WITH KETRA
CONTROL SUPPORT WITH KETRA 512 is an industry standard control protocol, built upon RS485, that has roots in entertainment and theatrical lighting applications. It is easy to use, robust and low cost and
More information5AMP Power Pack. Applications. Features. Specifications. Certifications & Affiliations. Catalog #: ALPP 5ACC or ALPP 5A Part #: or
Project name Prepared by Date INDOOR AIRLINK LUTRON Catalog #: ALPP 5ACC or ALPP 5A Part #: 632641 or 622559 The 5AMP power pack is a radio frequency device that controls up to 5A of general purpose load
More informationEcoSystem Digital Ballasts
EcoSystem Digital s 369339f 1 06.04.12 EcoSystem compact ballasts provide high-performance dimming for any compact uorescent application, including within an EcoSystem Lighting Control System. EcoSystem
More informationQuantumR Light Management Hub (QP2)
Quantum 369375f 1 11.05.15 QuantumR Hub (QP2) The Quantum light management hub provides a centralized connection point for Lutron EcoSystem digital ballast modules, Lutron power panels, and QS devices
More informationlighting control solutions switching systems
lighting control solutions switching systems Lutron switching capabilities A full line of switching systems with patented SoftswitchTM technology for projects of any size Softswitch128TM switching system
More informationSystem Programming User Guide
System Programming User Guide INSTALL MAINTAIN Table of Contents What is a Vive system?...4 Components...4 Installation / Wiring...4 Lutron Vive App...5 Initial Configuration...6 Connect to the Hub (via
More informationQSE-CI-DMX Control Interface
Control Interface The performs different functions depending on the system in which it is operating. The channels (maximum of 32) are mapped to HomeWorks zones and can be programmed as 1-channel lighting,
More informationEnergi Savr NodeTM for 0 10 V Energi Savr NodeTM with Softswitch
Energi Savr NodeTM for 0 0 V Energi Savr NodeTM with Softswitch The Energi Savr NodeTM (ESN) family is a group of modular products for the control of lighting, receptacles, and other loads. This document
More informationPico Wireless Control, 2-button, light icons in ivory
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 Lutron Catalog Number Manufacturer Description Weight per unit Product Category Features Frequency Range Material Material,
More informationEnergi Savr Node with DALI for Quantum
Energi Savr Node Digital Fixture Controller - CPN6916 Energi Savr Node with for Quantum 369794c 1 08.25.17 The Energi Savr Node family is a group of intelligent, modular products for the control of lighting
More informationQuantum Light Management Hub (QP3) for Quantum Select
for Select The Quantum provides a centralized connection point for Lutron power panels and QS devices. 369423f 1 10.06.16 Features Designed to control, manage, and monitor any Energi Savr NodeTM units,
More informationCONTRACT ROLLER Performance, Comfort, Value
CONTRACT ROLLER Performance, Comfort, Value New Contract Roller shades provide options for every space and budget to complement Lutron's comprehensive shades offerings 1 Lutron Why Lutron? Why Lutron shading
More informationHomeWorks QS Wired ArchitraveTM Keypads
HomeWorks QS Wired ArchitraveTM keypads provide homeowners with a simple and elegant way to operate lights, shades /draperies, motorized screens, thermostats, and many other devices. Replacement faceplates
More informationQS Sensor Module. product specifications a Model Numbers
The QS Sensor Module (QSM) is a ceiling-mounted device that integrates Lutron wireless and wired sensors through the wired QS Link on a HomeWorks QS processor. The QSM uses Clear Connect RF Technology
More information2. A Wi-Fi Ethernet router (802.11)
What hardware and software do I need? 1. An ipad, iphone or ipod touch with ios 3.1.3 or higher. (the ios version can be verified by opening the Settings App and selecting General, then selecting About
More information*Recommendations are subject to change. Consult your Lumenetix representative for the most updated list. Eco Loop 1. Eco Loop 2. Wallstation.
ECOSYSTEM PROTOCOL 1.1 Lutron EcoSystem Protocol EcoSystem technology is a control method for LEDs that provides addressing of individual fixtures and status feedback. This makes it easy to digitally assign
More informationFLUSH MOUNT DISK LIGHT
7 www.lum-techlighting.com FLUSH MOUNT & DISK LIGHT CMED-605 DoB 5 Ceiling Puck CMED-607 DoB 7 Ceiling Puck [CMED-605 : 5 ] (5.5"dia. x 1") Ceiling Puck Ceiling [ CMED-607 : 7 ] (7"dia. x 1") Ceiling Puck
More informationELK-M1XSP Serial Port Expander
-M1XSP Serial Port Expander Supplementary Instructions & Release Notes for Firmware Version 30.X.X This version provides M1 Integration to: JetStream ing Table of Contents M1XSP Installation and Setup...
More informationDistributed Power Series
GENERAL INFORMATION The Room Controller offers a full power and control solution for standalone and integrated room controls. With up to eight zones of relay switching with 0-10V control fully rated at
More informationOwner s Manual. Models 1503 and 1504 Basic Stand Alone Digital Keypad Entry Devices
Owner s Manual Models 1503 and 1504 Basic Stand Alone Digital Keypad Entry Devices DoorKing, Inc. 120 Glasgow Avenue Inglewood, California 90301 U.S.A. Phone: 310-645-0023 Fax: 310-641-1586 www.doorking.com
More informationPico Scene Keypads. Wireless Keypad and Mounting Accessories. Control Specification
Pico Scene Keypads The Pico wireless keypad is a flexible and easy to use device that allows the user to adjust multiple lights and shades to different levels at the touch of a button. This battery-operated
More information20AMP Plug Load Controller
Project name Prepared by Date INDOOR AIRLINK LUTRON Catalog#: ALPP 20A or ALPP 20ACC Part #: 624097 or 655228 The 20AMP plug load controller is a radiofrequency (RF), receptacle switching solution that
More informationHomeWorks Wired Signature Series Keypads
HomeWorks Wired Signature Series Keypads Indicator Lights Programmable buttons DESCRIPTI 048-027 1a 02.21.03 HomeWorks Signature Series keypads provide homeowners with a simple and elegant way to operate
More informationHomeWorks QS Processor
product specifications 369376d 06.03.15 The processor provides control and communication to system components. The Ethernet links allow communication to the software, integration with third party systems
More information6222 Two Door Module Technical Operations Manual
6222 Two Door Module Technical Operations Manual TABLE OF CONTENTS Specifications...3 Overview...4 Operations...5 Custom Access Mode...5 Standard Access Mode...5 Offline Access Mode...5 Offline Memory...5
More informationPOWER OVER ETHERNET. Lighting control system installation guide. H.E. Williams, Inc. Carthage, Missouri
Lighting control system installation guide H.E. Williams, Inc. Carthage, Missouri www.hew.com 417-358-4065 Introduction...1 References...1 System Overview...1 Cloud Portal Services...1 Gateway PC...1 Third-Party
More informationEGRX-2B-SL- - 2-Button Wallstation
EGRX-2B-SL- - 2-Button Wallstation Top Button Bottom Button egrx-1 12.9.03 Functionality can be indicate which button was pushed last. Works with GRAFIK Eye 3000 and 4000 Series Control Units. Invokes
More informationCasétaTM PD-5WS-DV. SPECIFICATION SUBMITTAL Page Job Name: Model Numbers: Job Number: Receiving Device
The controls various loads automatically through wireless sensors and wireless remote controls, providing a system that delivers energy savings, convenience, and ease of installation. The uses Lutron patented
More informationZone and Room Controllers
Zone and Room Controllers Echo Room Controllers respond to Echo Control Stations and provide relay or dimming functions for their local zones. Panels allow for the separation of circuits into multiple
More informationRadioRA 2 Product Reference Guide
RadioRA 2 was developed to work in any residence, new or existing. Easily install keypads, sensors, light controls, fan controls, temperature controls, appliance controls, and shades to create a system
More informationQSE-CI-DMX Control Interface
Control Interface 369372 Rev. B 1 08.12.11 Description The operates either in a standalone QS system or a Quantum system. It performs different functions depending on the system in which it is operating.
More informationLight Management Hub. Quantum 230 V CE Light Management Hub. Centralized Control Equipment
Quantum 69-77b 06.. Hub The Quantum light management hub provides a centralized connection point for Lutron QS devices, including Energi Savr NodeTM, GRAFIK Eye QS, Sivoia QS shades, and Lutron dimming
More informationEnergi Savr Node with Softswitch Design and Application Guide
Energi Savr Node with Softswitch Design and Application Guide Energi Savr Node with Softswitch Lutron solutions do more than just control the light in a space. With the right design strategies, they can
More informationGRAFIK 5000P / 6000P / 7000P Processor Panel
GRAFIK 5000P / 6000P / 7000P Processor Panel Processor panels store and/or process all of the information needed to run a GRAFIK 5000TM, GRAFIK 6000, or GRAFIK 7000TM centralized lighting control system,
More informationAMP100 AMP102 AMP110 AMP210 AMP310
Amplifier Guide AudioSource AMP series amplifiers are designed for home and commercial audio distribution systems where high quality sound, flexibility, and reliability are essential. The AMP series offers
More information