Input/Output Module (IOM) Series Controllers Catalog Page Code No. LIT Issued December 2017
|
|
- Andra Hardy
- 6 years ago
- Views:
Transcription
1 Input/Output Module () Series Controllers Catalog Page Code No. LIT Issued December 017 Refer to the QuickLIT website for the most up-to-date version of this document. The Input/Output Module () Series expansion I/O modules have integral RS-5 MS/TP communications and integrate into the web-based Metasys system. s can serve in one of two capacities, depending on where they are installed in the Metasys system. When installed on the Sensor/Actuator (SA) Bus of an Advanced Application Field Equipment Controller (FAC), Field Equipment Controller (FEC), or VAV Modular Assembly (VMA) controller, the expands the point count of these controllers. When installed on the Field Controller (FC) Bus, s can be used as I/O point multiplexors to support monitoring and control from an Network Automation Engine (NAE) or Network Control Engine (NCE). The point multiplexor can also be useful for sharing points between other field controllers on the FC Bus using peer-to-peer connectivity. Note: At CCT Release 10.1 and later, FACs, FECs, and VMAs can communicate by using either the BACnet or the N field bus networking protocol. The operation of the Input/Output Module is not affected by the selection of the BACnet or the N protocol in the host controller. All expansion modules are BACnet Testing Laboratory (BTL) listed. Refer to the Series Technical Specifications Table for details. Important: Important: You cannot purchase a similar third-party device and install it in a UL/ULC Listed smoke control system. Doing so voids the UL/ULC Smoke Control Listing. Third-party devices must be provided and labeled by the factory as described in the UL/ULC Smoke Control Listing. Only those Johnson Controls products identified for use in smoke control applications have been tested and listed by UL for use in a Metasys System UL 6 9th Edition UUKL/ORD-C UUKLC Smoke Control System. Installation of a product that is not UL/ULC Listed and labeled for this application prevents the entire system from being UL/ULC Listed for smoke control. Refer to the Metasys System Field Equipment Controllers and Related Products Product Bulletin (LIT-10110) for product application details. If the product fails to operate within its specifications, replace the product. For a replacement product, contact the nearest Johnson Controls representative. Input/Output Modules () Features Ability to Reside on the Field Controller (FC) Bus or Sensor/Actuator (SA) Bus Provides application flexibility. Standard BACnet Protocol Provides interoperability with other Building Automation System (BAS) products that use the widely accepted BACnet standard. BACnet Testing Laboratories (BTL) Listed Ensures interoperability with other BTL-listed devices. BTL is a third-party agency, which validates that BAS vendor products meet the BACnet industry-standard protocol. Standard Hardware and Software Platform Uses a common hardware design throughout the family line to support standardized wiring practices and installation workflows. Also uses a common software design to support use of a single tool for control applications, commissioning, and troubleshooting to minimize technical training. Universal Inputs, Configurable Outputs, and Point Expansion Modules Allows multiple signal options to provide input/output flexibility. Optional Local User Interface Display Allows convenient monitoring and adjusting capabilities at the local device. 3-bit Microprocessor Ensures optimum performance and meets industry specifications. BACnet Automatic Discovery Supports easy controller integration into a Metasys BAS. Pluggable Communications Bus and Supply Power Terminal Blocks Expedites installation and troubleshooting. Wireless Connectivity through the ZFR100 Series or the WNC100/ZFR1x Pro Series Wireless Field Bus Systems in MS/TP Controllers Enables wireless mesh connectivity to supervisory controllers, facilitating easy initial location and relocation. Bluetooth Wireless Commissioning Provides an easy-to-use connection to the configuration and commissioning tool. End-of-Line (EOL) Switch in MS/TP Field Controllers Enables field controllers to be terminating devices on the communications bus. Input/Output Module () Series Controllers Catalog Page 1
2 Table 1: Series Model Information (Including Point Type Counts) Communication Protocol Engines Modular Jacks Point Types Universal Input (UI) Signals Accepted Analog Input, Voltage Mode, Analog Input, Current Mode, 0 ma Analog Input, Resistive Mode, 0 kohm, RTD (1k NI [Johnson Controls], 1k PT, A99B SI), NTC (10k Type L,.5k Type ) Binary Input, Dry Contact Maintained Mode BACnet MS/TP All Model types. Some NIE models support MS/TP and N devices. Refer to the Network Engines Product Bulletin (LIT-10113) for details. 6-pin SA Bus Modular Port supports one communicating sensor. Or you can wire up to four communicating sensors to the SA Bus Terminal Block. They cannot be used at the same time. 6-pin FC Bus for tool support 6 Binary Input (BI) Dry Contact Maintained Mode Pulse Counter/Accumulator Mode (High Speed), 100 Hz Analog Output (AO) Analog Output, Voltage Mode, Analog Output, Current Mode, 0 ma Binary Output (BO) VAC Triac 3 Universal Output (UO) Analog Output, Voltage Mode, Binary Output Mode, VAC/DC Field-Effect Transistor (FET) Analog Output, Current Mode, 0 ma Configurable Output (CO) Analog Output, Voltage Mode, Binary Output Mode, VAC Triac Relay Output (RO) 10/0 VAC (-0 models only) Relay Output (RO) 0 VAC (- models only) 1 This model is currently only available in Asia. Contact your local Johnson Controls representative for more information. The BOs on the A and MS models require an external low-voltage power source. Table : Series Ordering Information Product Code Number MS MS MS-711- MS-71-0 MS Point with BI, FC Bus and SA Bus Support 6-Point with UI, UO, BO, FC Bus, and SA Bus Support. Relays are rated for 10/0 VAC. 6-Point with UI, UO, BO, FC Bus, and SA Bus Support. Relays are rated for 0 VAC. 10-Point with UI, AO, FC Bus, and SA Bus Support 10-Point with UI, AO, FC Bus, and SA Bus Support UL and cul (Canada) CE Marked Input/Output Module () Series Controllers Catalog Page
3 Table : Series Ordering Information Product Code Number MS MS MS MS MS MS A 1 MS MS Point with UI, UO, BO, FC Bus, and SA Bus Support. Relays are rated for 10/0 VAC. 1-Point with UI, UO, BO, FC Bus, and SA Bus Support. Relays are rated for 0 VAC. 16-Point with 16 BI, FC Bus, and SA Bus Support 16-Point with 16 BI, FC Bus, and SA Bus Support 16-Point with BI, BO, FC Bus, and SA Bus Support 16-Point with BI, BO, FC Bus, and SA Bus Support Binary Outputs (BOs) on MS-3733 controllers do not supply power for the outputs; the BOs require external low-voltage (<30 VAC) power sources. 16-Point with BI, BO, FC Bus, and SA Bus Support Binary Outputs (BOs) on MS A controllers do not supply power for the outputs; the BOs require external low-voltage (<30 VAC) power sources. 17-Point with 6 UI, BI, 3 BO, AO, CO, FC and SA Bus Support UL and cul (Canada) CE Marked 1 This model is currently only available in Asia. Contact your local Johnson Controls representative for more information. Table 3: Series for Smoke Control Ordering Information Product Code Number 1, MS U MS U MS-710-0U MS-711-0U MS U MS U MS-IOU710-0U MS-711-0U -Point with BI; VAC; FC Bus and SA Bus Support -Point with BI; VAC; FC Bus and SA Bus Support 6-Point with UI, UO, BO; VAC; FC Bus and SA Bus Support 6-Point with UI, UO, BO; VAC; FC Bus and SA Bus Support 1-Point with UI, UO, BO; VAC; FC Bus and SA Bus Support 1-Point with UI, UO, BO; VAC; FC Bus and SA Bus Support 17-Point with 6 UI, BI, 3 BO, AO, CO; VAC; FC Bus and SA Bus Support with Mounting Base 17-Point with 6 UI, BI, 3 BO, AO, CO; VAC; FC Bus and SA Bus Support with Mounting Base 1 These devices are UL/ULC 6 Listed, File S977, 9th Edition UUKL/ORD-C UUKLC Smoke Control System. These devices must be ordered in a Smoke Control UUKL listing. All field controllers in a smoke control system must be mounted in Johnson Controls custom or standard UL 6 panels or in panels that are ordered from Johnson Controls. If these field controllers are used with panels that are not supplied by Johnson Controls, they are not compliant with the UL 6 9th Edition UUKL/ORD-C UUKLC Smoke Control System listing. Input/Output Module () Series Controllers Catalog Page 3
4 Accessories Table : Accessories Product Code Number TL-MAP110-0P TL-MAP110-0S TL-MAP110-0PE TL-MAP110-0PA MS-BTCVT-1 MS-BTCVTCBL-700 ZFR100 Series Wireless Field Bus System ZFR-USBHA-0 Y6T15-0 Y65A13-0 Y65T-0 Y65T31-0 AP-TBKSA-0 AP-TBKFC-0 AP-TBK3PW-0 TL-BRTRP-0 Portable MAP Gateway for US/Canada - includes MAP Gateway, RJ-1 cable, bumper guard, and lanyard Stationary MAP Gateway for US/Canada - includes MAP Gateway, field bus adapter, mounting bracket, and AC power supply. (Adapters for the power supply may vary by country.) Portable MAP Gateway - for Europe (All EU Countries); Middle East (UAE and Qatar) Portable MAP Gateway - for Asia (China, Japan, Australia, New Zealand, India, Hong Kong, Singapore, Thailand) Wireless Commissioning Converter with Bluetooth Technology Cable Replacement Set for the MS-BTCVT-1 or the NS-ATV7003-0; Includes One 5 ft (1.5 m) Retractable Cable This system is used for installations that only support BACnet MS/TP. Refer to the WNC100/ZFR1x Pro Series Wireless Field Bus System Product Bulletin (LIT-10130) for a list of available products. ZFR USB Dongle provides a wireless connection through CCT to allow wireless commissioning of the wirelessly enabled FEC, Advanced Application Field Equipment Controller (FAC),, and VMA16 controllers. Also allows use of the ZFR Checkout Tool (ZCT) in CCT. Transformer, 10/0/0 VAC Primary to VAC Secondary, 9 VA, Foot Mount, 30 in. Primary Leads and 30 in. Secondary Leads, Class Transformer, 10 VAC Primary to VAC Secondary, 0 VA, Foot Mount (Y65AS), in. Primary Leads and 30 in. Secondary Leads, Class Transformer, 10/0/0 VAC Primary to VAC Secondary, 0 VA, Hub Mount (Y65SP+), in. Primary Leads and Secondary Screw Terminals, Class Transformer, 10/0/0 VAC Primary to VAC Secondary, 0 VA, Foot Mount (Y65AR+), in. Primary Leads and Secondary Screw Terminals, Class Replacement MS/TP SA Bus Terminal, -Position Connector, Brown (Bulk Pack of 10) Replacement MS/TP FC Bus Terminal, -Position Connector (Bulk Pack of 10) Replacement Power Terminal, 3-Position Connector, Gray (Bulk Pack of 10) Portable BACnet/IP to MS/TP Router Input/Output Module () Series Controllers Catalog Page
5 Series Technical Specifications Table 5: Series Product Code Numbers MS : -Point with BI, FC Bus and SA Bus Support MS-711-0: 6-Point with UI, UO, BO, FC Bus, and SA Bus Support. Relays are rated for 10/0 VAC MS-711-: 6-Point with UI, UO, BO, FC Bus, and SA Bus Support. Relays are rated for 0 VAC. MS-71-0: 10-Point with UI, AO, FC Bus, and SA Bus Support MS : 10-Point with UI, AO, FC Bus, and SA Bus Support MS : 1-Point with UI, UO, BO, FC Bus, and SA Bus Support. Relays are rated for 10/0 VAC MS-3711-: 1-Point with UI, UO, BO, FC Bus, and SA Bus Support. Relays are rated for 0 VAC MS-371-0: 16-Point with 16 BI, FC Bus, and SA Bus Support MS : 16-Point with 16 BI, FC Bus, and SA Bus Support MS : 16-Point with BI, BO, FC Bus, and SA Bus Support MS A 1 : 16-Point with BI, BO, FC Bus, and SA Bus Support MS : 16-Point with BI, BO, FC Bus, and SA Bus Support MS-711-0: 17-Point with 6 UI, BI, 3 BO, AO, CO, FC and SA Bus Support Smoke Control Models: MS U: -Point with BI, FC Bus and SA Bus Support MS U: -Point with BI, FC Bus and SA Bus Support MS-710-0U: 6-Point with UI, UO, BO, FC Bus, and SA Bus Support MS-711-0U: 6-Point with UI, UO, BO, FC Bus, and SA Bus Support MS U: 1-Point with UI, UO, BO, FC Bus, and SA Bus Support MS U: 1-Point with UI, UO, BO, FC Bus, and SA Bus Support MS-IOU710-0U: 17-Point with 6 UI, BI, 3 BO, AO, CO, FC Bus and SA Bus Support with Mounting MS-711-0U: 17-Point with 6 UI, BI, 3 BO, AO, CO, FC Bus and SA Bus Support with Mounting Supply Voltage Power Consumption VAC (nominal, 0 VAC minimum/30 VAC maximum), 50/60 Hz, Power Supply Class (North America), Safety Extra-Low Voltage (SELV) Europe 1 VA maximum Note: VA ratings do not include any power supplied to the peripheral devices connected to Binary Outputs (BOs) or Configurable Outputs (COs), which can consume up to 1 VA for each BO or CO, for a possible total consumption of an additional VA (maximum), depending on the model. Ambient Conditions Operating: 0 to 50 C (3 to 1 F); 10 to 90% RH noncondensing Storage: -0 to 0 C (-0 to 176 F); 5 to 95% RH noncondensing Addressing DIP switch set; valid field controller device addresses 17 (Device addresses 0 3 and 1 55 are reserved and not valid addresses). Communications Bus BACnet MS/TP, RS-5 3-wire FC Bus between the supervisory controller and field devices -wire SA Bus between field controller, network sensors, and other sensor/actuator devices. Includes a lead source 15 VDC supply power (from field controller) to bus devices. Processor MS , MS-711-0, MS-711-, MS-71-0, MS , MS-3711-, MS , MS A 1, and MS-711-0: HS/166xR Renesas 3-bit microcontroller MS , MS , MS : R631 3-bit Renesas microcontroller Memory MS , MS-711-0, MS-711-, MS-71-0, MS , MS-3711-, MS , MS A 1, and MS-711-0: 51 KB Flash Memory and 1 KB RAM MS , MS , and MS : MB External Serial Flash Memory Input/Output Module () Series Controllers Catalog Page 5
6 Table 5: Series Input and Output Capabilities MS : - Binary Inputs: Defined as Dry Contact Maintained or Pulse Counter/ Accumulator Mode MS-711-x: - Universal Inputs: Defined as, 0 ma, 0 600k ohm, or Binary Dry Contact - Universal Outputs: Analog Output: Voltage Mode, 0-10 VDC; Binary Output Mode: VAC/DC FET; Analog Output: Current Mode, -0 ma - Relay Outputs: (Single-Pole, Double-Throw) UL 916 (-0 model only): 1/ hp 10 VAC, 1/ hp 0 VAC; 360 VA Pilot Duty at 10/0 VAC (B300); 3 A Non-inductive -0 VAC EN (- model only): 6 () A N.O. or N.C. only, 0 VAC MS-71-0 and MS : - Universal Inputs: Defined as, 0 ma, 0 600k ohm, or Binary Dry Contact - Analog Outputs: Defined as or 0 ma MS-3711-x: - Universal Inputs: Defined as, 0 ma, 0 600k ohm, or Binary Dry Contact - Universal Outputs: Analog Output: Voltage Mode, 0-10 VDC; Binary Output Mode: VAC/DC FET; Analog Output: Current Mode, -0 ma - Relay Outputs: (Single-Pole, Double-Throw) UL 916 (-0 model only): 1/ hp 10 VAC, 1/ hp 0 VAC; 360 VA Pilot Duty at 10/0 VAC (B300); 3 A Non-inductive -0 VAC EN (- model only): 6 () A N.O. or N.C. only, 0 VAC MS and MS : 16 - Binary Inputs: Defined as Dry Contact Maintained or Pulse Counter/Accumulator Mode MS , MS A 1, and MS : - Binary Inputs: Defined as Dry Contact Maintained or Pulse Counter/Accumulator Mode - Binary Outputs: Defined as VAC Triac (Require external low-voltage power source) Note: Binary Outputs (BOs) on MS A and MS models do not supply power for the outputs; the BOs require external low-voltage (< 30 VAC) power sources. MS-711-0: 6 - Universal Inputs: Defined as, 0 ma, 0 600k ohm, or Binary Dry Contact - Binary Inputs: Defined as Dry Contact Maintained or Pulse/Counter Accumulator Mode 3 - Binary Outputs: Defined as VAC Triac (selectable internal or external source power) - Configurable Outputs: Defined as or VAC Triac BO - Analog Outputs: Defined as or 0 ma Analog Input/Analog Output Resolution and Accuracy MS , MS-711-0, MS-711-, MS-71-0, MS , MS-3711-, MS , MS A 1, and MS-711-0: Analog Input: 16-bit resolution Analog Output: 16-bit resolution and ±00 mv in applications MS , MS , and MS : Analog Input: 15-bit resolution Analog Output: ±00 mv in applications Input/Output Module () Series Controllers Catalog Page 6
7 Table 5: Series Terminations MS , MS-711-0, MS-711-, MS-71-0, MS , MS-3711-, MS , MS A 1, and MS-711-0: Input/Output: Fixed Screw Terminal Blocks SA/FC Bus and Supply Power: -wire and 3-wire Pluggable Screw Terminal Blocks SA/FC Bus Port: RJ-1 6-Pin Modular Jacks MS , MS , and MS : Input/Output: Fixed Screw Terminal Blocks Note: There are no labels on I/O terminal blocks. The labels are above/below the terminal blocks on the packaging. SA/FC Bus and Supply Power: -wire and 3-wire Pluggable Screw Terminal Blocks Mounting Housing Dimensions (Height x Width x Depth) Horizontal on single 35 mm DIN rail mount (preferred), or screw mount on flat surface with three integral mounting clips on controller Enclosure material: ABS and polycarbonate UL9 5VB; self-extinguishing, Plenum-rated protection class: IP0 (IEC59) MS-1711 and MS-711 Models: 150 x 10 x 53 mm (5-7/ x -3/ x -1/ in.) including terminals and mounting clips MS-71-0, MS , MS-371-0, MS , MS , and MS models: 150 x 16 x 53 mm (5-7/ x 6-7/16 x -1/ in.) including terminals and mounting clips MS and MS Models: 150 x 190 x 53 mm (5-7/ x 7-1/ x -1/ in.) including terminals and mounting clips Note: Mounting space for all field controllers requires an additional 50 mm ( in.) space on top, bottom, and front face of controller for easy cover removal, ventilation, and wire terminations. Weight Compliance 0.5 kg (1.1 lb) maximum United States: UL Listed, File E10701, CCN PAZ, UL 916, Energy Management Equipment; UL/ULC 6 Listed, File S977, 9th Edition UUKL/ORD-C UUKLC Smoke Control System (models with U product code suffix only); FCC Compliant to CFR7, Part 15, Subpart B, Class A Note: Except MS-711- and MS Canada: UL Listed, File E10701, CCN PAZ7, CAN/CSA C. No. 05, Signal Equipment; UL/ULC 6 Listed, File S977, 9th Edition UUKL/ORD-C UUKLC Smoke Control System (models with U product code suffix only); UL/ULC 6 Listed, File S977, 9th Edition UUKL/ORD-C UUKLC Smoke Control System (models with U product code suffix only); Industry Canada Compliant, ICES-003 Note: Except MS-711- and MS Europe: CE Mark Johnson Controls declares that this product is in compliance with the essential requirements and other relevant provisions of the EMC Directive. Declared as Independently Mounted, Intended for Panel Mounting, Operating Control Type 1.B, kv rated impulse voltage, C ball pressure test. Note: Except MS and MS Australia and New Zealand: RCM Mark, Australia/NZ Emissions Compliant Note: Except MS and MS BACnet International: MS , MS-711-0, MS-711-, MS-71-0, MS , MS-3711-, MS , MS A 1, and MS-711-0: BACnet Testing Laboratories (BTL) Protocol Revision Listed BACnet Application Specific Controller (B-ASC) MS , MS , and MS : BACnet Testing Laboratories (BTL) Protocol Revision 1 Listed BACnet Smart Actuator (B-SA) 1 This model is currently only available in Asia. Contact your local Johnson Controls representative for more information. For more information, refer to the MS/TP Communications Bus Technical Bulletin (LIT ). The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these specifications, consult the local Johnson Controls office. Johnson Controls shall not be liable for damages resulting from misapplication or misuse of its products. Building Technologies & Solutions 507 E. Michigan Street, Milwaukee, WI 530 Metasys and Johnson Controls are registered trademarks of Johnson Controls. All other marks herein are the marks of their respective owners. 017 Johnson Controls Published in U.S.A. Input/Output Module () Series Controllers Catalog Page 7
Input/Output Module (IOM) Series Controllers Catalog Page Code No. LIT Issued June 2018
Input/Output Module () Series Controllers Catalog Page Code No. LIT-190039 Issued June 01 Refer to the QuickLIT website for the most up-to-date version of this document. The Input/Output Module () Series
More informationInput/Output Module (IOM) Series Catalog Page
Input/Output Module () Series Catalog Page Johnson Controls www.johnsoncontrols.com LIT-1900349 2018-12-17 Input/Output Module () The Series expansion I/O modules have integral RS-485 MS/TP communications
More informationFX-PCX Expansion Input/Output Modules Catalog Page Code No. LIT Issued April 17, 2015
Expansion Input/Output Modules Catalog Page Code No. LIT-1900671 Issued April 17, 015 The s are expansion I/O modules with integral RS-5 MS/TP communications. Note: At FX-PCT Release 10.1, FX-PCVs, FX-PCGs,
More informationField Equipment Controller (FEC) Series Catalog Page Code No. LIT Issued June 2018
Code No. LIT-1900346 Issued June 018 Refer to the QuickLIT website for the most up-to-date version of this document. The Field Equipment Controller (FEC) Series products are programmable controllers that
More informationAdvanced Application Field Equipment Controller (FAC) Catalog Page
Advanced Application Field Equipment Controller (FAC) Catalog Page Code No. LIT-1900759 Issued February 018 Refer to the QuickLIT website for the most up-to-date version of this document. The Advanced
More informationFX-PCA Advanced Application Programmable Controller Catalog Page
FX-PCA Advanced Application Programmable Controller Catalog Page Code No. LIT-1900818 Issued April 2018 Refer to the QuickLIT website for the most up-to-date version of this document. FX-PCA Series Controllers
More informationFEC - FAC. Metasys controllers. Complex BAS Programmable controllers. Catalog Page. Field Equipment Controllers
Field Equipment Controllers The Metasys Field Equipment Controllers (FEC) are a complete family of BACnet compatible field controllers and accessories designed with the flexibility to meet a wide range
More informationPEAK TM. PEAK TM controllers. Mid-Market BAS Smart equipment controllers. HVAC/R controllers
Virtual Branch ecatalogue click here controllers HVAC/R controllers The PEAK 18 and PEAK 32 Controllers are configurable controllers that can be switched between MS/TP, Modbus RTU, and N2 Communication
More informationVMA Programmable VAV Box Controllers Catalog Page Code No. LIT Issued February 2018
Code No. LIT-900764 Issued February 08 Refer to the QuickLIT website for the most up-to-date version of this document. VMA6s (-bit) and VMA8s are programmable digital controllers tailored for VAV applications
More informationVMA Programmable VAV Box Controllers Catalog Page
Programmable VAV Box Controllers Catalog Page Johnson Controls www.johnsoncontrols.com LIT-1900764 2018-12-17 16 (32-bit), 18, and 1930 VAV Modular Assembly Controller Series 16s (32-bit) and 18s are
More informationFX-PC Series Programmable Controllers and Related Products Product Bulletin
FX-PC Series Programmable Controllers and Related Products Product Bulletin Code No. LIT-1011657 Software Release 6.0 Issued October 31, 013 Supersedes January 30, 013 Refer to the QuickLIT website for
More informationPEAK TM. SMART Equipment Controllers. Product bulletin
PEAK TM SMART Equipment Controllers Product bulletin The PEAK family of SMART Equipment Controllers comprises a group of versatile field controllers specifically designed for the HVAC/R market. The controller
More informationNetwork Control Engine Catalog Page
MS-NCE25xx-x Johnson Controls www.johnsoncontrols.com LIT-1900455 2018-12-17 Release 9.0.7 Introduction The Metasys Network Control Engine (NCE) Series controllers provide a cost-effective solution designed
More informationFX Input/Output (I/O) Modules XM07 and XM14
Product Bulletin FX I/O Modules Issue Date July 6, 2009 FX Input/Output (I/O) Modules XM07 and XM14 The FX Input/Output (I/O) Modules provide additional physical input and output points for FX field controllers
More informationSmart Equipment Controls (SEC)
Smart Equipment Controls (SEC) Product Bulletin SE-SPU1001-0, SE-SPU1002-0, SE-SPU1011-0, SE-SPU1011-0, SE-SPU1012-0, SE-SPU1004-0, SE-FDD1001-0, SE-ECO1001-0, SE-COM1001-0 Code No. LIT-12011934 Issued
More informationMetasys System Field Equipment Controllers and Related Products Product Bulletin
Metasys System Field Equipment Controllers and Related Products Product Bulletin Johnson Controls www.johnsoncontrols.com LIT-12011042 2018-12-17 Contents Contents Overview...5 Features and Benefits...6
More informationFX-PC Series Programmable Controllers and Related Products Product Bulletin
F-PC Series Programmable Controllers and Related Products Product Bulletin Code No. LIT-0657 Issued November 5, 05 Refer to the QuickLIT website for the most up-to-date version of this document. Overview
More informationMetasys System Field Equipment Controllers and Related Products Product Bulletin
Metasys System Field Equipment Controllers and Related Products Product Bulletin Code No. LIT-004 Issued December 07 Overview The Metasys system family of Field Equipment Controllers comprises a group
More informationFEC26 Field Equipment Controller
FEC26 Field Equipment Controller Installation Instructions MS-FEC2611-x MS-FEC2621-x Part No. 24-10143-144, Rev. D Release 5.3 Issued December 5, 2011 Supersedes October 4, 2010 Applications The FEC26
More informationFeatures Communication Using Commonly Accepted IT Standards, Including Web Services, at the Automation and Enterprise Level Web-Based User Interface
MS-NAE35xx-x, MS-NAE45xx-x, MS-NAE55xx-x, NAE8500-0 Code No. LIT-1900195 Software Release 6.5 Issued February 14, 2014 Supersedes June 17, 2013 Network Automation Engines (NAEs) provide comprehensive equipment
More informationFX-DIS1710 Local Controller Display Installation Instructions Part No , Rev. B Issued April 2016
FX-DIS1710-0 Part No. 24-10240-17, Rev. B Issued April 2016 Applications The FX-DIS1710 Local Controller Display is a stand-alone display module designed for installation on the front panel of an enclosure.
More informationApplication and Data Server (ADS) Lite-A System Catalog Page
Application and Data Server (ADS) Lite-A System Catalog Page MS-ADSLAU-, MS-NAE41L-2 Code No. LIT-1900691 Software Release 9.0 Issued August 22, 2017 Refer to the QuickLIT website for the most up-to-date
More informationNetwork Integration Engine (NIEx9) for Third-Party Integrations Catalog Page
Network Integration Engine (NIEx9) for Third-Party Integrations Catalog Page MS-NIE29xx-0, MS-NIE39xx-x, MS-NIE49xx-x, MS-NIE59xx-x, MS-NIE89xx-x Code No. LIT-1900881 Software Release 9.0 Issued December
More informationIOM47 Input/Output Module Installation Instructions Part No , Rev. K Issued April 2016
MS-IOM4711-x Part No. 24-10144-92, Rev. K Issued April 2016 Application The IOM47 field controller is part of the Metasys system Field Equipment Controller family. Input/Output Module (IOM) controllers
More informationFXVMA Variable Air Volume (VAV) Box Controller
FXVMA Product Bulletin FXVMA Issue Date November 21, 2008 FXVMA Variable Air Volume (VAV) Box Controller The FXVMA is an integrated assembly used to control Variable Air Volume (VAV) boxes. The FXVMA consists
More informationFEC26 Extended Temperature Field Equipment Controller
FEC26 Extended Temperature Field Equipment Controller Installation Instructions MS-FEC2611-0ET Part No. 24-10143-292, Rev. C Issued June 20, 2014 Supersedes November 13, 2013 Applications The FEC26 extended
More informationFEC25 Field Equipment Controller Installation Instructions Part No , Rev. A Issued April 2016
MS-FEC2511-0 Part No. 24-10143-802, Rev. A Issued April 2016 Application The FEC25 controllers are part of the Metasys system Field Equipment Controller (FEC) family. The FEC2511 is a modification of the
More informationIOM47 Input/Output Module Installation Instructions Part No , Rev. L Issued November 2017
MS-IOM4711-x Part No. 24-10144-92, Rev. L Issued November 2017 Application The IOM47 field controller is part of the Metasys system Field Equipment Controller family. Input/Output Module (IOM) controller
More informationFAC Advanced Application Field Equipment Controller Installation Instructions
FAC2612-2 Advanced Application Field Equipment Controller Installation Instructions MS-FAC2612-2 Part No. 24-10143-233, Rev. J Issued November 2017 Application The FAC2612-2 Advanced Application Field
More informationFX-BTCVT Bluetooth Commissioning Converter Installation Instructions
FX-BTCVT Bluetooth Commissioning Converter Installation Instructions FX-BTCVT-1 Part No. 24-10108-10, Rev. A Issued January 30, 2013 Supersedes April 12, 2011 Applications The FX-BTCVT Bluetooth Commissioning
More informationNetwork Control Engine
Network Control Engine Product Bulletin MS-NCE25xx-x The Metasys Network Control Engine (NCE) Series controllers combine the network supervisor capabilities and Internet Protocol (IP) network connectivity
More informationLN Series Remote Input/Output (I/O) Modules
LN Series Remote Input/Output (I/O) Modules Product Bulletin LN-IO301-1, LN-IO401-1, LN-IO520-1 Code No. LIT-12011316 Issued June 5, 2012 Supersedes November 9, 2007 The LN Series Remote Input/Output (I/O)
More informationVerasys System Product Bulletin
Code No. LIT-12012342 Issued January 2017 Refer to the QuickLIT website for the most up-to-date version of this document. Verasys system improves occupant comfort by Figure 1: Verasys System providing
More informationFEC26 Field Equipment Controllers Installation Instructions MS-FEC2611-x, MS-FEC2621-x, MS-FEC2611-xET
MS-FEC2611-x, MS-FEC2621-x, MS-FEC2611-xET Part No. 24-10143-144, Rev. L Issued November 2017 Application The FEC26 controllers are part of the Metasys system Field Equipment Controller (FEC) family. These
More informationFEC1611 and FEC1621 Field Equipment Controller Installation Instructions
FEC1611 and FEC1621 Field Equipment Controller Installation Instructions MS-FEC1611-1, MS-FEC1611-1U, MS-FEC1621-1, MS-FEC1611-1ET Part No. 24-10143-136, Rev. L Issued November 2017 Refer to the QuickLIT
More informationUNT1100 Series. Binary Output Jumpers AO2 AO1 AO3 AO4 AOCM AOCM AOCM AOCM AO1. AI Switches Job Information N2 Address. Ref N2+ N2- ADDR 0 = ALL OPEN
1 2 8 4 AI6 R R Installation Bulletin UNT1100 Issue Date 0309 UNT1100 Series Introduction The Unitary (UNT) controller (UNT1100 Series) is a digital controller with applications for air handling units,
More informationOnboard Inputs and Outputs. Remote User Interface. Integral LCD User Interface
Product Bulletin: FX06 Field Controller Issue Date: March 2006 FX06 Field Controller The FX06 is a compact field controller in the Facility Explorer range of products. The controller is designed specifically
More informationNCE25 Installation Instructions MS-NCE25xx-x
MS-NCE25xx-x (barcode for factory use only) Part No. 24-10143-63, Rev. R Software Release 9.0 Issued August 2017 Refer to the QuickLIT website for the most up-to-date version of this document. Application
More informationLX Series Remote Input/Output (I/O) Controller
LX Series Remote Input/Output (I/O) Controller Product Bulletin LX-IO520-1, LX-IO401-1, LX-IO301-1 Code No. LIT-12011491 Issued June 22, 2009 The LX Series Remote Input/Output (I/O) controller extends
More informationNetwork Automation Engine Catalog Page MS-NAE35xx-x, MS-NAE45xx-x, MS-NAE55xx-x, NAE Software Release 8.1 Issued February 2017
MS-NAE35xx-x, MS-NAE45xx-x, MS-NAE55xx-x, NAE8500-0 Code No. LIT-1900195 Software Release 8.1 Issued February 2017 Network Automation Engines (NAEs) provide comprehensive equipment monitoring and control,
More informationTC-9102 Terminal Controller
Metasys Network Sales Resource Manual 635 Application Specific Controllers Section Product Bulletin Issue Date 1095 TC-9102 Terminal Controller The TC-9102 Terminal Controller, the latest addition to the
More informationVMA1610 and VMA1620 Variable Air Volume Controllers Installation Instructions
VMA1610 and VMA1620 Variable Air Volume Controllers Installation Instructions MS-VMA1610-xU, MS-VMA1620-xU Part No. 24-10143-20, Rev. U Issued November 2017 Applications The VMA1610/1620 controllers are
More informationNIEx9. Metasys. BAS network automation Supervisory controllers. Network Integration Engine
Virtual Branch ecatalogue click here Metasys Network Integration Engine Network Integration Engines (s) for 3 rd party integrations enable Internet Protocol (IP) connectivity and Web-based access to Metasys
More informationMedium User Interface (MUI) Version 3
Medium User Interface (MUI) Version 3 Product Bulletin Medium User Interface (MUI) Issue Date October 21, 2009 The MUI is a remote user interface device for the FX Platform that supports FX06, FX07, FX14,
More informationFX-PCX17 and FX-PCX27 Expansion Input/Output Module Installation Instructions
FX-PCX17 and FX-PCX27 Expansion Input/Output Module Installation Instructions FX-PCX1711 Series, FX-PCX2711 Series Part No. 24-10144-106, Rev. F Issued March 2016 Application The FX-PCX17 and FX-PCX27
More informationNIE59 Network Integration Engine Figure 1: NIE59 Network Integration Engine
Network Integration Engine (NIEx9) for 3rd Party Integrations Product Bulletin MS-NIE59xx-1E, MS-NIE49xx-2E MS-NIE39xx-2E, MS-NIE29xx-0E Software Release 5.1 Issued Mar 23, 2011 Network Integration Engines
More informationFX06 Field Controller
Code No. LIT-1900406 Issued October 19, 2012 Facility Explorer FX06 Field Controller The FX06 is a high performance field controller designed specifically for commercial Heating, Ventilating, Air Conditioning,
More informationNetwork Automation Engine Catalog Page MS-NAE35xx-x, MS-NAE45xx-x, MS-NAE55xx-x, MS-NAE551S-2, NAE Software Release 9.0 Issued August 2017
MS-NAE35xx-x, MS-NAE45xx-x, MS-NAE55xx-x, MS-NAE551S-2, Code No. LIT-1900195 NAE8500-0 Software Release 9.0 Issued August 2017 Network Automation Engines (NAEs) provide comprehensive equipment monitoring
More informationFX-PCG26 General Purpose Programmable Controller Installation Instructions
FX-PCG26 General Purpose Programmable Controller Installation Instructions FX-PCG2611-x, FX-PCG2621-x Application The FX-PCG controller is part of the Facility Explorer Programmable Controller (FX-PC)
More informationFX-PCA Advanced Application Programmable Controller Installation Instructions
FX-PCA2611-0 Advanced Application Programmable Controller Installation Instructions FX-PCA2611-0 Part No. 24-10143-403, Rev. E Issued April 2016 Application The FX-PCA2611-0 Advanced Application Programmable
More informationFX-PCA3611 Advanced Application Programmable Controller Installation Instructions
FX-PCA3611 Advanced Application Programmable Controller Installation Instructions FX-PCA3611 Part No. 24-10143-616, Rev. B Issued April 2016 Application The FX-PCA3611 Advanced Application Programmable
More informationIOM2721 Input/Output Module Installation Instructions MS-IOM2721
MS-IOM2721 Part No. 24-10144-149, Rev. K Issued August 2018 Application The IOM2721 input/output expansion module is part of the Metasys system Field Equipment Controller family. Input/Output Module (IOM)
More informationModular Room Control (MRC) Series Expansion Board
Installation Instructions Issue Date December 13, 2002 Modular Room Control (MRC) Series Expansion Board Application The Modular Room Control (MRC) system has the ability to expand its input/output capabilities
More informationNAE. Metasys. BAS network automation Supervisory controllers. Network Automation Engine
Virtual Branch ecatalogue click here Metasys Network Automation Engine Network Automation Engines (s) enable Internet Protocol (IP) connectivity and web-based access to Metasys Building Management Systems
More informationLX Series Free Programmable LX-PRG6x0-11 Controllers and LX Series Input/Output (I/O) Extension Modules
LX Series Free Programmable LX-PRG6x0-11 Controllers and LX Series Input/Output (I/O) Extension Modules Product Bulletin LX-PRG600-11, LX-PRG610-11, LX-IOE400-0 LX-IOE410-0, LX-IOE420-0 Code No. LIT-12011854
More informationWireless Metasys System
Metasys Product Bulletin Code No. LIT-12011244 Software Release 5.0 Issued January 4, 2010 Supersedes February 25, 2009 The Metasys provides a wireless platform for multiple levels of the Johnson Controls
More informationFX14 Field Controller
Product Bulletin FX14 Field Controller Issue Date January 22, 2010 FX14 Field Controller The FX14 is a high performance field controller designed specifically for commercial Heating, Ventilating, Air Conditioning,
More informationWNC1800/ZFR182x Pro Series Wireless Field Bus System
WNC1800/ZFR182x Pro Series Wireless Field Bus System Product Bulletin Code No. LIT-12012320 Issued February 2017 The WNC1800/ZFR182x Pro (ZFR Pro) Series Wireless Field Bus System provides a wireless platform
More informationZFR1800 Series Wireless Field Bus System
Code No. LIT-1900509 Issued December 5, 2014 ZFR1800 Series Wireless Field Bus System Description The ZFR1800 Series Wireless Field Bus System provides a wireless platform for all Metasys Field Equipment
More informationNetwork Automation Engine
Network Automation Engine Product Bulletin MS-NAE35xx-x, MS-NAE45xx-x MS-NAE55xx-x, NAE8500-0 Network Automation Engines (NAEs) enable Internet Protocol (IP) connectivity and Web-based access to Metasys
More informationNAE55/NIE55 Installation Instructions MS-NAE55xx-3, MS-NIE55xx-3, MS-NAE5510-2U
MS-NAE55xx-3, MS-NIE55xx-3, MS-NAE5510-2U (barcode for factory use only) Part No. 24-10051-43, Rev. N Software Release 9.0 Issued August 2017 Refer to the QuickLIT website for the most up-to-date version
More informationNetwork Integration Engine (NIEx9) for Third-Party Integrations Product Bulletin
Network Integration Engine (NIEx9) for Third-Party Integrations Product Bulletin MS-NIE9xx-0, MS-NIE39xx-x, MS-NIE49xx-x, MS-NIE59xx-x, MS-NIE89xx-x Code No. LIT-093 Software Release 9.0 Issued December
More informationBuy American Facility Explorer Products Facility Explorer Product Management Authorized Building Controls Specialists (ABCS)
Date: January 26, 2012 Announcing: From: Released To: Buy American Facility Explorer Products Facility Explorer Product Management Authorized Building Controls Specialists (ABCS) Product Johnson Controls,
More informationXT-9100 Technical Bulletin
System 9100 Technical Manual 636.4 Technical Bulletins Section Technical Bulletin Issue Date 0896 XT-9100 Technical Bulletin XT-9100 Extension Module/XP-910x Expansion Modules Page 3 Introduction 3 SX
More informationLab and Central Plant Controller
Metasys Network Sales Resource Manual 635 Application Specific Controllers Section Product Bulletin Issue Date 0290 Lab and Central Plant Controller The Metasys Lab and Central Plant (LCP) Controller is
More informationFX-DIS Local Controller Display Technical Bulletin
FX-DIS Local Controller Display Technical Bulletin FX-DIS1710-0 Code No. LIT-12011666 Issued February 28, 2014 Supersedes April 12, 2011 Refer to the QuickLIT website for the most up-to-date version of
More informationSpecification Sheet For electronically commutated motors
SC-VAV-N Specification Sheet For electronically commutated motors Used in constant pressure applications The SC-EFC is designed to control exhaust air in various building applications. The system includes
More informationLN Series Free Programmable LN-PRG6x0-12 Controllers and LN Series Input/Output (I/O) Extension Modules
LN Series Free Programmable LN-PRG6x0-12 Controllers and LN Series Input/Output (I/O) Extension Modules Product Bulletin LN-PRG600-12, LN-PRG610-12, LN-IOE400-0 LN-IOE410-0, LN-IOE420-0 Code No. LIT-12011800
More informationSuitable for a wide range of installations with wall-mount, flush-mount and hand-held remote control options.
TUC03 Configurable Terminal Unit Controller Product Bulletin The TUC03 Configurable Terminal Unit Controller is designed specifically to provide direct digital control of terminal unit applications with
More informationMetasys N1 Network Integration
Product Bulletin Issue Date March 31, 2003 Metasys N1 Network Integration The Metasys N1 Network Integration solution connects existing Metasys N1 based building automation systems into the new generation
More informationDatasheet. ECB-PTU Series. 1/14. BACnet B-ASC Powered Terminal Unit Programmable Controllers. Overview
Datasheet BACnet B-ASC Powered Terminal Unit Programmable Controllers Overview Applications Meets the requirements of the following applications: Fan Coil Units Heat Pumps Chilled Beams Reversible Ceiling
More informationAndover ContinuumTM. b3850 Series Terminal Controllers
TM b3850 Series Terminal Controllers The TM b3850 series controllers are native BACnet controllers that communicate on an RS-485 field bus as Master devices using the MS/TP BACnet protocol. 02 Features
More informationBACnet. b3867 Terminal Controllers
BACnet b3867 Terminal Controllers The Andover Continuum TM b3867 is a native BACnet controller that communicates on an RS-485 field bus as a Master device using the MS/TP BACnet protocol. 02 Features Product
More informationExtended Digital Controller
The Metasys Extended Digital Controller Metasys Network Sales Resource Manual 635 Application Specific Controllers Section Product Bulletin Issue Date 1093 Extended Digital Controller (DX-9100) is the
More informationVariable Air Volume Modular Assembly (VMA) 1400 Series
Product Bulletin Issue Date March 27, 2009 Variable Air Volume Modular Assembly (VMA) 1400 Series The Variable Air Volume Modular Assembly (VMA) Series is a family of configurable digital controllers.
More informationFX40 Supervisory Controller
Product Bulletin FX40 Issue Date March 1, 2007 FX40 Supervisory Controller The FX40 brings a new generation of Web based technology into the Facility Explorer product family. The FX40 manages a network
More informationAndover ContinuumTM b3865/866 VAV Controllers with Built-in Actuator
Andover ContinuumTM b3865/866 VAV Controllers The Andover Continuum TM b3865 and b3866 are native BACnet controllers that communicate on an RS-485 field bus as Master devices using the MS/TP BACnet protocol.
More informationDX-9100 Digital Controller, Version 2
Metasys European Sales Resource Manual Application Specific Controllers Section Product Bulletin Issue Date 1298 DX-9100 Digital Controller, Version 2 The DX-9100 Digital Controller is the ideal digital
More informationAndover Continuum Infinet II i2865/866 VAV Controllers with Built-in Actuator
Andover Continuum Infinet II i2865/866 VAV Controllers with Built-in Actuator The i2865 and i2866 are unique, low-cost VAV box controllers that come equipped with a built-in actuator to streamline hardware
More informationTX-I/O Product Range. Description. Technical Specification Sheet Document No February 20, 2018
Technical Specification Sheet Document No. 149-476 February 20, 2018 TX-I/O Product Range TX-I/O is a range of I/O modules, with associated power and communication modules, for use within the APOGEE Automation
More informationField selectable application type and room module series, via dip-switches on controller
TUC03 Plus Configurable Terminal Unit Controller Product bulletin The TUC03 Plus configurable Terminal Unit Controller is specifically designed to provide an improved BACnet integration. It allows the
More informationTX-I/O Product Range. Description. Technical Specification Sheet Document No July 18, 2013
Technical Specification Sheet Document No. 149-476 July 18, 2013 TX-I/O Product Range TX-I/O is a range of I/O modules, with associated power and communication modules, for use within the APOGEE Automation
More informationWNC1800/ZFR182x Pro Series Wireless Field Bus System Quick Reference Guide
WNC1800/ZFR182x Pro Series Wireless Field Bus System Quick Reference Guide Code No. LIT-12012319 Issued February 2017 Refer to the QuickLIT website for the most up-to-date version of this document. Introduction................................................................1
More informationAndover ContinuumTM Infinet II
Andover ContinuumTM Infinet II i2920 System Controllers The Andover Continuum Infinet II i2920 System Controller is designed to meet the needs of your most demanding control and monitoring applications
More informationBACnet B-ASC Powered Terminal Unit Programmable Controllers. Overview
Datasheet BACnet B-ASC Powered Terminal Unit Programmable Controllers Applications Meets the requirements of the following applications: Fan Coil Units Heat Pumps Chilled Beams Reversible Ceiling with
More informationMS/TP Communications Bus Technical Bulletin Code No. LIT Software Release 9.0 Issued December 2017
Code No. LIT-12011034 Software Release 9.0 Issued December 2017 Refer to the QuickLIT website for the most up-to-date version of this document. Document Introduction...3 Summary of Changes...3 MS/TP Bus
More informationVMA1615/1626/1628/1630 VAV Controllers Installation Instructions
VMA1615/1626/1628/1630 VAV Controllers Installation Instructions MS-VMA1615, MS-VMA1626, MS-VMA1628, MS-VMA1630 Part No. 24-10143-217, Rev. F Issued July 2017 Applications The VMA1615/1626/1628/1630 programmable
More informationBACnet. b3810 Series Local Controllers
BACnet b380 Series Local Controllers The Andover Continuum TM b380 series controllers are designed for control of Air Handling Units, Roof Top Units, and other mechanical plant equipment. 0 Features Choose
More informationZFR1800 Series Wireless Field Bus System
ZFR1800 Series Wireless Field Bus System Product Bulletin Code No. LIT-12011336 Software Release 5.0 Issued January 4, 2010 Supersedes February 25, 2009 The ZFR1800 Series Wireless Field Bus System uses
More informationN2 Dialer Module. Features and Benefits
Metasys Network Sales Resource Manual 635 Application Specific Controllers Section Product Bulletin Issue Date 1194 N2 Dialer Module The N2 Dialer Module (NDM) provides a low-cost method of connecting
More information8 channel universal input and 4 channel Form C digital output
1 I/O Modules UI-8/DO-FC-4 and UI-8/DO-FC-4-H 8 channel universal input and 4 channel Form C digital output Introduction The UI-8/DO-FC-4 and UI-8/DO-FC-4-H are universal input, 8 channel and digital output,
More informationNetwork Integration Engine
Network Integration Engine Product Bulletin MS-NIE55xx-x MS-NIE8500-x Code No. LIT-1201537 Software Release 5.2 Issued December 19, 2011 Supersedes May 13, 2011 Refer to the QuickLIT Web site for the most
More informationCommercial Comfort System (CCS)
Commercial Comfort System (CCS) Product Bulletin Code No. LIT-12011347 Issued June 16, 2015 The Commercial Comfort System (CCS) improves occupant comfort by providing reliable zoning control of standard
More informationFP-PS-4. Features. Installation
OPERATING INSTRUCTIONS FP-PS-4 FieldPoint Power Supply These operating instructions describe the installation, features, and characteristics of the FP-PS-4. Features The FP-PS-4 is a FieldPoint power supply
More informationHMISBC Rear Module controller panel - Dig 8 inputs/8 outputs +Ana 4 In/2 Out
Product data sheet Characteristics HMISBC Rear Module controller panel - Dig 8 inputs/8 outputs +Ana 4 In/2 Out Main Range of product Product or component type Device presentation Complementary Supply
More informationNIE39/NIE49 Installation Instructions MS-NIE39xx-2, MS-NIE49xx-2
MS-NIE39xx-2, MS-NIE49xx-2 Application (barcode for factory use only) Part No. 24-10050-103, Rev. H Software Release 9.0 Issued August 2017 Refer to the QuickLIT website for the most up-to-date version
More informationNetwork Integration Engine Product Bulletin
MS-NIE55xx-x MS-NIE8500-x Code No. LIT-1201537 Software Release 7.0.7 Issued April 2016 Refer to the QuickLIT website for the most up-to-date version of this document. The Metasys Network Integration Engine
More informationLCS85 Turnkey User's Guide Part No , Rev. F Software Release 6.1 Issued June 17, 2013 Supersedes January 30, 2011
MS-LCS8520-0 Part No. 24-10526-11, Rev. F Software Release 6.1 Issued June 17, 2013 Supersedes January 30, 2011 Refer to the QuickLIT website for the most up-to-date version of this document. LCS85 Turnkey
More informationTX-I/O Product Range. Features. Description. Technical Specification Sheet Document No January 24, 2007
Technical Specification Sheet Document No. 149-476 January 24, 2007 TX-I/O Product Range Description TX-I/O is a line of I/O modules with associated power and communication modules for use within the APOGEE
More informationNS Series Network Sensors
Code No. LIT-1900350 Issued March 4, 2013 NS Series Network s Description The NS Series Network offering includes NS Series Network Zone s and NS Series Network Discharge Air s. The NS Series Network s
More information