Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share
|
|
- Kory Burns
- 6 years ago
- Views:
Transcription
1 Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share Revised: February 26, 2013 When Cisco MXE 3500 integration is enabled in Cisco Show and Share, videos uploaded to Cisco Show and Share are delivered to the Cisco MXE 3500 for transcoding. When the transcoding is complete, the transcoded videos are returned to Cisco Show and Share. Prerequisites, page 1 Guidelines and Limitations, page 1 Configure the Cisco MXE 3500, page 3 Register the Cisco MXE 3500 in the Cisco DMM, page 5 Configure Cisco Show and Share to Use the Cisco MXE 3500, page 6 Testing the Integration, page 9 User Experience, page 10 Prerequisites Cisco Show and Share Release or later. Cisco Media Experience Engine 3500 (MXE 3500) Release 3.2 or later. Administrator login credentials for the Cisco Show and Share and Cisco MXE Cisco MXE Release 3.3 and Cisco Show and Share Release 5.3 are required for Pulse video analytics. For Pulse Analytics, the Cisco MXE 3500 must have a Pulse feature license installed. Guidelines and Limitations You can only configure one Cisco MXE 3500 or Cisco MXE 3500 cluster in Cisco Show and Share. There is no co-location requirement for Cisco Show and Share and Cisco MXE 3500 hardware. The appliances can be deployed anywhere in the network provided that they can communicate by using FTP (TCP port 21) and HTTP (TCP port 80). Cisco Show and Share uses FTP to submit user videos 1
2 Guidelines and Limitations Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share to Cisco MXE 3500 and retrieve transcoded versions, and uses HTTP to submit transcoding job requests. If network loading or bandwidth are a concern with large video files, Cisco Show and Share and the Cisco MXE 3500 should be co-located. The Cisco MXE 3500 licenses, Standalone and Resource Manager, both work for this integration. Other than the functional differences between the two licenses, there are no specific configuration limitations. When integrating Cisco Show and Share with a Cisco MXE 3500 cluster (resource nodes managed by a resource manager), observe these guidelines: Verify that the resource nodes (RNs) have full control access to the \\mxe_ip_address\dms shared folder on the Resource Manager (RM) appliance. mxe_ip_address is the IP address of the standalone or the RM appliance. When configuring the host setting, we recommend using the IP address for the RM. Verify that the RNs can reach the RM IP address. Configure the FTP client settings on Cisco Show and Share to communicate with Cisco MXE If Pulse video analytics is enabled, the processing time to add keywords and speaker identification is approximately 1.5 times the length of the video. A one-hour video takes approximately one and one-half hours to process. In Cisco Show and Share Release 5.3, videos are transcoded to MP4 format using the H.264 video codec. You can configure the transcoding process to produce up to three versions of the video using different resolutions: 360p Low resolution. The Cisco Show And Share mobile client displays videos in this resolution. Viewers can also select this resolution for smoother playback over slow connections. 480p Medium resolution. Videos transcoded to this resolution are also transcoded to 360p. 720p High resolution. Videos transcoded to this resolution are also transcoded to 480p and 360p. Table 1 Transcoded File Specifications Size Resolution 4:3 16:9 Bitrate 360p 480x x kbps 480p 640x x kbps 720p 960x x kbps Note Cisco Show and Share does not upscale a video. For example, if you set transcoding for all three resolutions, and upload a video at 480p, Cisco Show and Share will only produce the 480p and 360p versions of the video. 2
3 Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share Configure the Cisco MXE 3500 Integrating Cisco MXE 3500 Release 3.3 that has Pulse video analytics enabled with Cisco Show and Share Release 5.3 adds keywords and speaker identification to video content. In Cisco Show and Share, viewers click on the keyword or speaker to go to the corresponding location in the video. Pulse Video Analytics is a licensed feature on Cisco MXE 3500 Release 3.3. In Cisco Show and Share Release 5.2.x, videos are transcoded to Flash video 8 (.flv) format with the following specifications: Bitrate: 400 bps Frame rate: 30 fps Maximum height: 268 pixels Maximum width: 480 (for 16:9 ratio), 360 (for 4:3 ratio) Configure the Cisco MXE 3500 Configuring Cisco Show and Share Integration and dmsftp, page 3 Disabling API Authentication on Cisco MXE 3500, page 5 Configuring Pulse Video Analytics, page 5 Configuring Cisco Show and Share Integration and dmsftp Note In a clustered deployment, perform all configuration steps on the RM appliance. Step 1 SSH to mxe_ip_address, where mxe_ip_address is the hostname or IP address for the Cisco MXE Step 2 Step 3 Step 4 When the Welcome to the Media Experience Engine screen displays, press Alt+F1 to log in to the Linux administration utility. Log in as admin. The configuration menu appears. Select Configure Cisco Show and Share Integration, and click OK. 3
4 Configure the Cisco MXE 3500 Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share Figure 1 Configure Cisco Show and Share Integration Step 5 In the Configure Cisco Show and Share Integration screen, select Enable Cisco Show and Share Integration. Figure 2 Configure Cisco Show and Share FTP Account Step 6 Step 7 Step 8 Enter a password for dmsftp in the Password field. Reenter the password in the Verify Password field. Click OK. 4
5 Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share Register the Cisco MXE 3500 in the Cisco DMM Disabling API Authentication on Cisco MXE 3500 You must disable API basic authentication in the Cisco MXE 3500 to integrate with Cisco Show and Share. Step 1 Step 2 Step 3 Step 4 Step 5 Log into the Cisco MXE 3500 web UI ( by using an admin account. From the Toolbox, click Administration > API Admin. In the Configure Authentication Mode section, click Edit. Choose Unauthenticated Mode. This option specifies that the MXE REST API does not require any authentication. No API components are blocked, giving users unrestricted access to all and any API components. Click Save. Note Cisco MXE 3500 uses the mode that you configure upon save. The Cisco MXE 3500 web UI and APIs will not be accessible for 1-2 minutes while the authentication mode change is applied. Configuring Pulse Video Analytics For information on how to configure Pulse Video Analytics on Cisco MXE 3500, see the Administration Guide for Cisco Media Experience Engine 3500 on Cisco.com. Register the Cisco MXE 3500 in the Cisco DMM Note Cisco MXE 3500 must be registered in Cisco DMM for Cisco Show and Share to use Cisco MXE Step 1 Step 2 Step 3 Log into Cisco DMM ( as superuser or as an administrator. Click Administration. Choose Settings > External Servers > MXE. The Media Experience Engine settings page appears. 5
6 Configure Cisco Show and Share to Use the Cisco MXE 3500 Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share Figure 3 Media Experience Engine Settings Step 4 Select Enabled in the Use of MXE field. Enter the Cisco MXE 3500 fully qualified domain name or IP address in the MXE FQDN field, for example mxe.cisco.com. Step 5 Enter the FTP credentials that you configured on the Cisco MXE 3500: Field Username Password Value Enter dmsftp. The dmsftp account password that you entered in the Configuring Cisco Show and Share Integration and dmsftp procedure. Step 6 Step 7 Click Save. Cisco DMM verifies the connection to the Cisco MXE If it cannot contact the Cisco MXE 3500, an error message appears. If you receive an error, verify your settings. Configure Cisco Show and Share to Use the Cisco MXE 3500 Step 1 Step 2 Step 3 Log into Cisco Show and Share with admin or superuser privileges. Choose Administration from the global navigation. Choose Setup > MXE Settings (Show and Share Release 5.3) or Media Experience Engine (Show and Share Release 5.2.x). The Media Experience Engine Settings page displays. 6
7 Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share Configure Cisco Show and Share to Use the Cisco MXE 3500 Figure 4 Media Experience Engine Settings Page Release 5.3 Figure 5 Media Experience Engine Settings Page Release Step 4 Step 5 Select Enable Media Experience Engine. Depending on the Cisco Show and Share Release, do one of the following: For Cisco Show and Share Release 5.3, page 8 For Cisco Show and Share Release 5.2.x, page 8 7
8 Configure Cisco Show and Share to Use the Cisco MXE 3500 Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share For Cisco Show and Share Release 5.3 a. Select one of the following resolutions: 360p Produces one video at 360p resolution 480p Produces two videos at 360p and 480p resolution respectively 720p Produces three videos, at 360p, 480p, and 720p resolution respectively Note If you select 720p, videos are automatically transcoded to 480p and 360p. Similarly if you select 480p, videos are automatically transcoded to 360p. Note Cisco Show and Share does not upscale a video. If you select 720p and upload a video at 480p, Cisco Show and Share will only produce the 480p and 360p versions of the video. b. (Optional) Select Windows Media Files (.WMV) c. Click Save. Step 6 For Cisco Show and Share Release 5.2.x a. Select one of the following choices: Do not transcode Windows Media video content. Prevents Windows media files (.wmv,.wma,.asx, and.asf) from being transcoded. They will be handled natively by Cisco Show and Share. Users will not be able to use the built-in video editor with these file types. This option is enabled by default. Allow Windows media content to be transcoded. Allows Windows media files to be transcoded by the Cisco MXE. Users that are uploading Windows media files are given the option to skip transcoding and have the files processed natively by Cisco Show and Share. They would want to skip transcoding if their media contained embedded closed captioning. When Windows media video content is transcoded, any embedded Closed Captioning is lost. b. Click Save. Enable Pulse For Cisco Show and Share Release 5.3 only a. Choose Manage > Preferences and Settings. b. Under Settings, check Pulse Spoken Keyword and Speaker Recognition. c. Click Apply. 8
9 Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share Testing the Integration Figure 6 Enable Pulse in Cisco Show and Share Release 5.3 Testing the Integration Cisco Show and Share now automatically submits transcoding jobs to the Cisco MXE Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Upload a video to Cisco Show and Share, and save it as a draft. Log in to the Cisco MXE 3500 user interface. Choose Monitoring > Job Status. A job will be running without a Job Profile Name. Select the job. The Tasks tab displays the job details. When the Cleanup task is complete, the Cisco MXE 3500 has completed the transcoding and deleted the submitted video from the C:\dms\input folder. On Cisco Show and Share, the status of the uploaded video will change from Processing - Draft to Draft. You can now publish the transcoded video in the Cisco Show and Share video portal. 9
10 User Experience Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share Figure 7 Job Details in Cisco MXE 3500 User Experience 1. Upload Video to the Cisco Show and Share video portal. Tip If you have Pulse video analytics enabled, upload the video as Draft. This allows you to review and edit the Speaker names before publishing the video. The status shows as Processing-Draft. If you select the Go to Publish Page option when the video is uploaded, the status shows as Processing-Publish. Cisco Show and Share submits the video by using FTP to the Cisco MXE 3500 for transcoding. The Cisco MXE 3500 transcodes the video; if Pulse video analytics is enabled, Cisco MXE 3500 also applies keyword tags and speaker IDs to the video content. Cisco Show and Share uses the MXE API to submit and poll the status of the job it submitted. When the Cisco MXE 3500 completes processing the video, Cisco Show and Share uses FTP to copy the transcoded video to the Cisco Show and Share video portal. 2. After the status changes to Draft, click on Edit Video to review and edit or tag the speaker names. 10
11 Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share User Experience If the Go to Publish Page option is selected during video upload, the status changes to Published. The video is automatically published to Cisco Show and Share. To review and edit the speaker names, click Manage Video, then Save as Draft. In the draft copy, click Edit Video to edit or identify the speaker names. Once a speaker is identified, the system recognizes and automatically identifies the speaker in subsequent videos. 3. Publish the enhanced video content for sharing. 11
12 User Experience Transcode and Add Pulse Video Analytics to Video Content on Cisco Show and Share 12
Capture Transform Share Configuration Guide
Capture Transform Share Configuration Guide Revised February 26, 2013 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000
More informationDeploying Cisco MXE 3500 Release 3.2 in Standalone Configuration
CHAPTER 4 Deploying Cisco MXE 3500 Release 3.2 in Standalone Configuration Revised: June 3, 2011 This section includes the following topics: About Cisco MXE 3500 Release 3.2, page 4-2 About the Cisco MXE
More informationCapture Transform Share Video Delivery
Capture Transform Share Video Delivery 2 Capture Transform Share (CXS) Agenda Capture Transform Share (CXS) Overview (5-10mins) Solution Components (15 mins) Demo (15 mins) CXS Architecture (10 mins) Deployment
More informationAdministrator Guide for Cisco Show and Share 5.2.x
Administrator Guide for Cisco Show and Share 5.2.x Including Show and Share Reports 5.2.x May 31, 2011 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com
More informationJob Profiles. Introduction to Job Profiles. Send document feedack to CHAPTER
CHAPTER 6 Revised: March 12, 2010 are templates that define how jobs should be processed; they can contain part or all the settings required to process jobs from beginning to final distribution. This chapter
More informationDeploying the Cisco Tetration Analytics Virtual
Deploying the Cisco Tetration Analytics Virtual Appliance in the VMware ESXi Environment About, on page 1 Prerequisites for Deploying the Cisco Tetration Analytics Virtual Appliance in the VMware ESXi
More informationGetting Started Using Cisco License Manager
CHAPTER 5 This chapter provides information about the initial setup of Cisco License Manager and an overview of recommended steps to quickly add users and devices and obtain and deploy licenses. This chapter
More informationThe Cisco Show and Share mobile client for Apple ios devices will provide the following features when connected to a Cisco Show and Share system:
Data Sheet Cisco Show and Share Product Overview The Cisco Digital Media Suite (DMS) is a comprehensive offering of webcasting and video sharing, digital signage, and business IPTV applications that can
More informationCisco Show and Share Failover Configuration
CHAPTER 3 Revised: March 2011, This chapter describes how to configure failover on a Cisco Show and Share installation. It covers both new installations and adding failover to an existing installation.
More informationIntegration Note for ECDS with Cisco Show and Share, Cisco Media Experience Engine 3500, and Cisco Digital Media Players
Integration Note for ECDS with Cisco Show and Share, Cisco Media Experience Engine 3500, and Cisco Digital Media Players Revised: December 12, 2011 This document provides only the basic configuration workflows
More informationBuilding Block Installation - Admins
Building Block Installation - Admins Overview To use your Blackboard Server with Panopto, you first need to install the Panopto Building Block on your Blackboard server. You then need to add Blackboard
More informationRelease 8.6, page 2 Configure Cisco Unity Connection for Use with Cisco Jabber, page 3
for an On-Premises Deployment with Cisco Unified Communications Manager Release 9.x and Later, page 1 for an On-Premises Deployment with Cisco Unified Communications Manager Release 8.6, page 2 Configure
More informationUpgrade Guide for Cisco Digital Media System Release 5.0
Upgrade Guide for Cisco Digital Media System Release 5.0 Revised: December 12, 2008, This guide provides information about and instructions for upgrading your Cisco DMS appliances and Cisco Digital Media
More informationBMC FootPrints 12 Integration with Remote Support
BMC FootPrints 12 Integration with Remote Support 2003-2019 BeyondTrust Corporation. All Rights Reserved. BEYONDTRUST, its logo, and JUMP are trademarks of BeyondTrust Corporation. Other trademarks are
More informationVersion 3.5 Organization Administrator Guide
Version 3.5 Organization Administrator Guide This document provides information Ensemble Video Organization Administrators can use to manage Ensemble Video libraries and users. April 2013 Table of Contents
More informationCreate, Add, and Manage Videos
CHAPTER 4 Revised: May 31, 2011 Topics in this section describe ways that you can contribute video and supplemental files to your Cisco Show and Share community. Prerequisites, page 4-1 Procedures, page
More informationSetup for Cisco Unified Communications Manager
Setup for Cisco Unified Communications Manager This chapter describes how you can set up Cisco Jabber for ipad using Cisco Unified Communications Manager. System and Network Requirements, page 1 Recommended
More informationInstalling Cisco MSE in a VMware Virtual Machine
Installing Cisco MSE in a VMware Virtual Machine This chapter describes how to install and deploy a Cisco Mobility Services Engine (MSE) virtual appliance. Cisco MSE is a prebuilt software solution that
More informationConfigure and Troubleshoot TCS Live streaming and Video on Demand with VBrick DME and VBrick Rev
Configure and Troubleshoot TCS Live streaming and Video on Demand with VBrick DME and VBrick Rev Contents Introduction Prerequisites Requirements Components Used Background Information Configure Network
More informationUse a Cisco DME to Transcode Video
14 CHAPTER Revised: May 31, 2011 Features on the Digital Media Encoders tab help you to transcode AVI and MPEG2 files into WMV files. This transcoding makes such video files compatible with and reuseable
More informationWelcome to the e-learning course for SAP Business One Analytics Powered by SAP HANA: Installation and Licensing. This course is valid for release
Welcome to the e-learning course for SAP Business One Analytics Powered by SAP HANA: Installation and Licensing. This course is valid for release 9.0. 1 At the end of this course, you will be able to discuss
More informationGenesys Interaction Recording Solution Guide. Deploying SpeechMiner for GIR
Genesys Interaction Recording Solution Guide Deploying SpeechMiner for GIR 7/19/2018 Contents 1 Deploying SpeechMiner for GIR 1.1 Installing SpeechMiner 1.2 Upgrading SpeechMiner 1.3 Configuring SpeechMiner
More informationThe Balabit s Privileged Session Management 5 F5 Azure Reference Guide
The Balabit s Privileged Session Management 5 F5 Azure Reference Guide March 12, 2018 Abstract Administrator Guide for Balabit s Privileged Session Management (PSM) Copyright 1996-2018 Balabit, a One Identity
More informationDeploy the ExtraHop Discover Appliance in Azure
Deploy the ExtraHop Discover Appliance in Azure Published: 2018-04-20 The following procedures explain how to deploy an ExtraHop Discover virtual appliance in a Microsoft Azure environment. You must have
More informationCisco Integrated Management Controller (IMC) Supervisor is a management system that allows you to manage rack mount servers on a large scale.
Contents Introduction Prerequisites Requirements Qualified Serviers Minimum Firmware Versions Supported PCiE Cards Supported Hypervisor versions Supported Browser Versions Configure Deploying Cisco IMC
More informationRecovery Procedure for Cisco Digital Media Manager 5.2
CHAPTER 1 Recovery Procedure for Cisco Digital Media Manager 5.2 Revised: May 3, 2010, This document provides the information that you require to recover from a software failure of the Cisco Digital Media
More informationPre-Deployment Checklist & Instructions
Pre-Deployment Checklist & Instructions RISC-BP-PDCL-02042015 Contents Pre-Deployment Checklist...3 Pre-Deployment Instructions...4 Advanced Setup (NAT Configuration)...7 TrafficSim Checklist...8 TrafficSim
More informationRecovering Cisco MXE 3500
CHAPTER 7 Recovering Cisco MXE 3500 Revised: January 26, 2010, Caution This recovery process resets your Cisco MXE 3500 to the same state and configuration in which it was delivered to you. All changes
More informationUser Guide
User Guide 03.10.2016 Contents 1 Introduction...3 1.1 IT Requirements...3 1.2 Installing efireservice Video...4 1.3 Login to efireservice Video...4 2 Video Library...5 2.1 Additional Video Details...5
More informationAssessment - OMS Gateway and Data Collection Machine Setup. Prerequisites
Assessment - OMS Gateway and Data Collection Machine Setup Prerequisites Ensure that you have reviewed the information in the assessment s prerequisites and configuration document before continuing the
More informationInstalling Cisco StadiumVision Director Software from a DVD
Installing Cisco StadiumVision Director Software from a DVD First Published: May 29, 2012 Revised: August 2, 2012 This module describes how to install the Cisco StadiumVision Director Release 3.0 software
More informationVersion 3.3 System Administrator Guide
Version 3.3 System Administrator Guide This document provides information Ensemble Video System Administrators can use to design and implement an appropriate Ensemble Video organizational framework, manage
More informationInstalling Cisco CMX in a VMware Virtual Machine
Installing Cisco CMX in a VMware Virtual Machine This chapter describes how to install and deploy a Cisco Mobility Services Engine (CMX) virtual appliance. Cisco CMX is a prebuilt software solution that
More informationDeploy the ExtraHop Discover 3100, 6100, 8100, or 9100 Appliances
Deploy the ExtraHop Discover 3100, 6100, 8100, or 9100 s Published: 2017-12-29 This guide explains how to install the rack-mounted EDA 3100, EDA 6100, EDA 8100, and EDA 9100 ExtraHop Discover appliances.
More informationWorkspace ONE UEM Certificate Authentication for Cisco IPSec VPN. VMware Workspace ONE UEM 1810
Workspace ONE UEM Certificate Authentication for Cisco IPSec VPN VMware Workspace ONE UEM 1810 You can find the most up-to-date technical documentation on the VMware website at: https://docs.vmware.com/
More informationDeploying VMware Identity Manager in the DMZ. JULY 2018 VMware Identity Manager 3.2
Deploying VMware Identity Manager in the DMZ JULY 2018 VMware Identity Manager 3.2 You can find the most up-to-date technical documentation on the VMware website at: https://docs.vmware.com/ If you have
More informationDeploy the ExtraHop Explore Appliance in Azure
Deploy the ExtraHop Explore Appliance in Azure Published: 2018-07-19 In this guide, you will learn how to deploy an ExtraHop Explore virtual appliance in a Microsoft Azure environment and join multiple
More informationVMware Skyline Collector Installation and Configuration Guide. VMware Skyline 1.4
VMware Skyline Collector Installation and Configuration Guide VMware Skyline 1.4 You can find the most up-to-date technical documentation on the VMware website at: https://docs.vmware.com/ If you have
More informationvapp Deployment and Configuration Guide
vapp Deployment and Configuration Guide vcenter Operations Manager 5.8.5 This document supports the version of each product listed and supports all subsequent versions until the document is replaced by
More informationReset the Admin Password with the ExtraHop Rescue CD
Reset the Admin Password with the ExtraHop Rescue CD Published: 2018-01-19 This guide explains how to reset the administration password on physical and virtual ExtraHop appliances with the ExtraHop Rescue
More informationCisco TelePresence Authenticating Cisco VCS Accounts Using LDAP
Cisco TelePresence Authenticating Cisco VCS Accounts Using LDAP Deployment Guide Cisco VCS X8.2 D14465.07 June 2014 Contents Introduction 3 Process summary 3 LDAP accessible authentication server configuration
More informationTenable.sc-Tenable.io Upgrade Assistant Guide, Version 2.0. Last Revised: January 16, 2019
Tenable.sc-Tenable.io Upgrade Assistant Guide, Version 2.0 Last Revised: January 16, 2019 Table of Contents Welcome to the Tenable.sc-Tenable.io Upgrade Assistant 3 Get Started 4 Environment Requirements
More informationRAP as a Service for Exchange Server: Prerequisites
RAP as a Service for Exchange Server: Prerequisites This document explains the required steps to configure the RAP as a Service for Exchange Server. There are two scenarios available to configure the assessment.
More informationSetting Up Resources in VMware Identity Manager (On Premises) Modified on 30 AUG 2017 VMware AirWatch 9.1.1
Setting Up Resources in VMware Identity Manager (On Premises) Modified on 30 AUG 2017 VMware AirWatch 9.1.1 Setting Up Resources in VMware Identity Manager (On Premises) You can find the most up-to-date
More informationACS 5.x: LDAP Server Configuration Example
ACS 5.x: LDAP Server Configuration Example Document ID: 113473 Contents Introduction Prerequisites Requirements Components Used Conventions Background Information Directory Service Authentication Using
More informationPxM Proof of Concept Configuration. June 2018 Version 3.1
PxM Proof of Concept Configuration June 2018 Version 3.1 Table of Contents PxM Architecture, Installation & Configuration... 3 PxM Proof of Concept (POC) Guide... 4 Introduction... 4 Prerequisites... 4
More informationMULTI FACTOR AUTHENTICATION USING THE NETOP PORTAL. 31 January 2017
MULTI FACTOR AUTHENTICATION USING THE NETOP PORTAL 31 January 2017 Contents 1 Introduction... 2 1.1 Prerequisite for configuring the multi-factor authentication:... 2 1.1.1 On the Guest side... 2 1.1.2
More informationSetting Up Resources in VMware Identity Manager (SaaS) Modified 15 SEP 2017 VMware Identity Manager
Setting Up Resources in VMware Identity Manager (SaaS) Modified 15 SEP 2017 VMware Identity Manager Setting Up Resources in VMware Identity Manager (SaaS) You can find the most up-to-date technical documentation
More informationVMware AirWatch Database Migration Guide A sample procedure for migrating your AirWatch database
VMware AirWatch Database Migration Guide A sample procedure for migrating your AirWatch database For multiple versions Have documentation feedback? Submit a Documentation Feedback support ticket using
More informationDeploying VMware Identity Manager in the DMZ. SEPT 2018 VMware Identity Manager 3.3
Deploying VMware Identity Manager in the DMZ SEPT 2018 VMware Identity Manager 3.3 You can find the most up-to-date technical documentation on the VMware website at: https://docs.vmware.com/ If you have
More informationTable of Contents. Configure and Manage Logging in to the Management Portal Verify and Trust Certificates
Table of Contents Configure and Manage Logging in to the Management Portal Verify and Trust Certificates Configure System Settings Add Cloud Administrators Add Viewers, Developers, or DevOps Administrators
More informationVMware Identity Manager Cloud Deployment. Modified on 01 OCT 2017 VMware Identity Manager
VMware Identity Manager Cloud Deployment Modified on 01 OCT 2017 VMware Identity Manager You can find the most up-to-date technical documentation on the VMware Web site at: https://docs.vmware.com/ The
More informationVMware Identity Manager Cloud Deployment. DEC 2017 VMware AirWatch 9.2 VMware Identity Manager
VMware Identity Manager Cloud Deployment DEC 2017 VMware AirWatch 9.2 VMware Identity Manager You can find the most up-to-date technical documentation on the VMware website at: https://docs.vmware.com/
More informationSystem Setup. Accessing the Administration Interface CHAPTER
CHAPTER 3 The system can be configured through the web interface to provide the networking configuration for the appliance and other system settings that are important such as time and SSL certificate.
More informationCDP Data Center Console User Guide CDP Data Center Console User Guide Version
CDP Data Center Console User Guide CDP Data Center Console User Guide Version 3.18.2 1 README FIRST Welcome to the R1Soft CDP Data Center Console User Guide The purpose of this manual is to provide you
More informationPolicy Manager for IBM WebSphere DataPower 7.2: Configuration Guide
Policy Manager for IBM WebSphere DataPower 7.2: Configuration Guide Policy Manager for IBM WebSphere DataPower Configuration Guide SOAPMDP_Config_7.2.0 Copyright Copyright 2015 SOA Software, Inc. All rights
More informationIntegration Guide. LoginTC
Integration Guide LoginTC Revised: 21 November 2016 About This Guide Guide Type Documented Integration WatchGuard or a Technology Partner has provided documentation demonstrating integration. Guide Details
More informationQuick Start Guide for Vmware. Version 2.5 Vmware vsphere Instance
Quick Start Guide for Vmware Version 2.5 Vmware vsphere Instance CONTENTS 1. Introduction 1.1 Running Gemini appliance on Vmware vsphere 1.1.1 Supported Versions 1.1.2 System Requirement 1.1.3 Note on
More informationMigrate Data from Cisco Secure ACS to Cisco ISE
Migrate Data from Cisco Secure ACS to Cisco ISE This chapter describes exporting and importing Cisco Secure ACS, Release 5.5 or later data into Cisco ISE, Release 2.3 system using the migration tool. Export
More informationCisco Expressway Authenticating Accounts Using LDAP
Cisco Expressway Authenticating Accounts Using LDAP Deployment Guide Cisco Expressway X8.5 December 2014 Contents Introduction 3 Process summary 3 LDAP accessible authentication server configuration 4
More informationVMware AirWatch Certificate Authentication for Cisco IPSec VPN
VMware AirWatch Certificate Authentication for Cisco IPSec VPN For VMware AirWatch Have documentation feedback? Submit a Documentation Feedback support ticket using the Support Wizard on support.air-watch.com.
More informationDeploy the ExtraHop Trace 6150 Appliance
Deploy the ExtraHop Trace 6150 Appliance Published: 2018-04-20 This guide explains how to install the rack-mounted ETA 6150 ExtraHop Trace appliances. System requirements This guide explains how to install
More informationDVS-200 Configuration Guide
DVS-200 Configuration Guide Contents Web UI Overview... 2 Creating a live channel... 2 Inputs... 3 Outputs... 6 Access Control... 7 Recording... 7 Managing recordings... 9 General... 10 Transcoding and
More informationakkadian Global Directory 3.0 System Administration Guide
akkadian Global Directory 3.0 System Administration Guide Updated July 19 th, 2016 Copyright and Trademarks: I. Copyright: This website and its content is copyright 2014 Akkadian Labs. All rights reserved.
More informationBranding Customizations
Branding Overview, page 1 Branding Prerequisites, page 1 Branding Task Flow, page 2 Branding File Requirements, page 4 Branding Overview The Branding feature lets you upload customized branding for Cisco
More informationLicensing the Application CHAPTER
CHAPTER 5 Licensing Application, Configuring E-mail, Cisco.com, Proxy Settings, RCP, SCP Settings, Security, Backup, Authentication Settings and Idle Timeout Settings, Browser and Server Security Mode
More informationCisco TelePresence Content Server S4.1
Cisco TelePresence Content Server S4.1 Online help (printable format) D14595.03 December 2010 Contents Logging in to the web interface... 6 Supported browsers, plugins & platforms... 7 Supported browsers...
More informationInstalling the Cisco Unified MeetingPlace Web Server Software
Installing the Cisco Unified MeetingPlace Web Server Software Release 8.5 Revised: 2/19/13 : Install the Application Server (which includes the Software Media Server) : Install the Hardware Media Server
More informationDeploy the ExtraHop Explore 5100 Appliance
Deploy the ExtraHop Explore 5100 Appliance Published: 2018-09-25 In this guide, you will learn how to configure the rack-mounted EXA 5100 ExtraHop Explore appliance and to join multiple Explore appliances
More informationRestrictions for Secure Copy Performance Improvement
The Protocol (SCP) feature provides a secure and authenticated method for copying router configuration or router image files. SCP relies on Secure Shell (SSH), an application and a protocol that provide
More informationACE Live on RSP: Installation Instructions
ACE Live on RSP ACE Live on RSP: Installation Instructions These installation instructions apply to OPNET ACE Live on RSP Release 7.1.3. You can find the latest version of this document at the OPNET Support
More informationPAN 802.1x Connector Application Installation Guide
PAN 802.1x Connector Application Installation Guide Version 1.2 "Copyright CodeCentrix. All rights reserved 2015. Version 1.2 Contact Information CodeCentrix www.codecentrix.co.za/contact Email: info@codecentrix.co.za
More informationSetting Up the Server
Managing Licenses, page 1 Cross-launch from Prime Collaboration Provisioning, page 5 Integrating Prime Collaboration Servers, page 6 Single Sign-On for Prime Collaboration, page 7 Changing the SSL Port,
More informationInstalling or Upgrading ANM Virtual Appliance
CHAPTER 2 This chapter describes how to deploy Cisco ANM Virtual Appliance 4.3 (new installation) and how to upgrade from ANM software version 4.1 or 4.2 to software version 4.3. This chapter includes
More informationInstallation of Cisco Business Edition 6000H/M
Installation Overview, page 1 Installation Task Flow of Cisco Business Edition 6000H/M, page 2 Installation Overview This chapter describes the tasks that you must perform to install software on your Business
More informationOrchestrate Video MMD Live Guide
Orchestrate Video MMD Live Guide May 2016 Information herein, including the URL and other Internet website references, is subject to change without notice. Unless otherwise noted, the companies, organizations,
More informationRemote Support 19.1 Web Rep Console
Remote Support 19.1 Web Rep Console 2003-2019 BeyondTrust Corporation. All Rights Reserved. BEYONDTRUST, its logo, and JUMP are trademarks of BeyondTrust Corporation. Other trademarks are the property
More informationForeScout CounterACT. Controller Plugin. Configuration Guide. Version 1.0
ForeScout CounterACT Network Module: Centralized Network Controller Plugin Version 1.0 Table of Contents About the Centralized Network Controller Integration... 4 About This Plugin... 4 How It Works...
More informationAuthenticating Cisco VCS accounts using LDAP
Authenticating Cisco VCS accounts using LDAP Cisco TelePresence Deployment Guide Cisco VCS X6 D14526.04 February 2011 Contents Contents Document revision history... 3 Introduction... 4 Usage... 4 Cisco
More informationMigrating vrealize Automation 6.2 to 7.2
Migrating vrealize Automation 6.2 to 7.2 vrealize Automation 7.2 This document supports the version of each product listed and supports all subsequent versions until the document is replaced by a new edition.
More informationRealms and Identity Policies
The following topics describe realms and identity policies: About, page 1 Create a Realm, page 8 Create an Identity Policy, page 14 Create an Identity Rule, page 15 Manage a Realm, page 17 Manage an Identity
More informationvrealize Automation Management Pack 2.0 Guide
vrealize Automation Management Pack 2.0 Guide This document supports the version of each product listed and supports all subsequent versions until the document is replaced by a new edition. To check for
More informationRealms and Identity Policies
The following topics describe realms and identity policies: About, page 1 Create a Realm, page 8 Create an Identity Policy, page 15 Create an Identity Rule, page 15 Manage a Realm, page 20 Manage an Identity
More informationWorking with Cisco UCS Manager
This chapter includes the following sections: Cisco UCS Domains and Cisco UCS Central, page 1 Registering a Cisco UCS Domain Using Cisco UCS Manager GUI, page 3 Registering a Cisco UCS Domain Using Cisco
More informationCisco TelePresence VCS Cluster Creation and Maintenance
Cisco TelePresence VCS Cluster Creation and Maintenance Deployment Guide Cisco VCS X8.5 Cisco TMS 13.2 or later December 2014 Contents Introduction 4 Prerequisites 5 Upgrading an X7.1 or later cluster
More informationIntroducing Cisco License Manager
CHAPTER 1 Cisco License rapidly acquires and deploys a large number of software licenses and tracks license status for an entire network. Tip If you are using Cisco License for the first time, see the
More informationDell EMC Extensions for VMware vrealize Automation
Dell EMC Extensions for VMware vrealize Automation Administration Guide Version 1.0 May 2018 H17049.1 Administration Guide Abstract This administration guide describes how to implement and manage Dell
More informationManaging NCS User Accounts
7 CHAPTER The Administration enables you to schedule tasks, administer accounts, and configure local and external authentication and authorization. Also, set logging options, configure mail servers, and
More informationArticulate Engage 2013 Tutorial
How to Access Engage 1. By Launching Engage Directly o You can open Engage directly from the desktop by clicking on the green Engage Icon, which is shown in the top right corner of this manual. 2. By Launching
More informationRED IM Integration with Bomgar Privileged Access
RED IM Integration with Bomgar Privileged Access 2018 Bomgar Corporation. All rights reserved worldwide. BOMGAR and the BOMGAR logo are trademarks of Bomgar Corporation; other trademarks shown are the
More informationSend document feedack to
CHAPTER 9 This chapter includes the following topics: Introduction to Administration, page 9-1 Host Administration, page 9-2 System Administration, page 9-13 Profile Spaces, page 9-33 User Metadata, page
More informationConfiguring WebConnect
CHAPTER 6 WebConnect provides seamless integration between multiple internal and external web servers through a single URL. Making use of a single database and a customer-defined rollover sequence, WebConnect
More informationSaaSaMe Transport Workload Snapshot Export for. Alibaba Cloud
SaaSaMe Transport Workload Snapshot Export for Alibaba Cloud Contents About This Document... 3 Revision History... 3 Workload Snapshot Export for Alibaba Cloud... 4 Workload Snapshot Export Feature...
More informationRemote Support Web Rep Console
Remote Support Web Rep Console 2017 Bomgar Corporation. All rights reserved worldwide. BOMGAR and the BOMGAR logo are trademarks of Bomgar Corporation; other trademarks shown are the property of their
More informationPrivileged Remote Access Jumpoint Guide
Privileged Remote Access Jumpoint Guide 2003-2018 BeyondTrust, Inc. All Rights Reserved. BEYONDTRUST, its logo, and JUMP are trademarks of BeyondTrust, Inc. Other trademarks are the property of their respective
More informationManaging User Roles and Users in LMS
7 CHAPTER This chapter explains the following: Managing Roles Managing Users Managing Roles A role is a collection of privileges that dictate the type of system access you have. The Manage User Roles workflow
More informationEditing the Home Page
Editing the Home Page Logging on to Your Web site 1. Go to https://extension.usu.edu/admin/ 2. Enter your Login and Password. 3. Click Submit. If you do not have a login and password you can request one
More informationakkadian Provisioning Manager Express
akkadian Provisioning Manager Express Version 4.11.04 Release Notes September 14 th, 2017 Copyright and Trademarks: I. Copyright: This website and its content is copyright 2017 Akkadian Labs, LLC. All
More informationYour environment will now be created. The status is Creating. You can use the Refresh button to refresh the page.
MANUAL This guide helps you getting started with SaasNow within a few steps. Create SAS environment 1. You received an email from SaasNow where you can create your login details. 2. Log in to /login with
More informationConnect the Appliance to a Cisco Cloud Web Security Proxy
Connect the Appliance to a Cisco Cloud Web Security Proxy This chapter contains the following sections: How to Configure and Use Features in Cloud Connector Mode, on page 1 Deployment in Cloud Connector
More information