OpenAir Electronic Damper Actuator GDE/GLB Rotary Non-spring Return
|
|
- Violet Bradley
- 6 years ago
- Views:
Transcription
1 OpenAir Electronic Damper Actuator GDE/GLB Rotary Non-spring Return Document No EA678R a b e d c f a. Actuator b. Position indicator c. Mounting bracket d. Mounting screws e. 4 mm hex key f. Shaft insert for use with /8-inch (8- mm) shafts Product Description Steps for direct-coupled mounting of the OpenAir GDE/GLB Series non-spring return rotary electronic damper actuator. Figure. Parts of the GDE/GLB Rotary Actuator. Instructions WARNING: Do not open the actuator. Product Numbers GDE.U GDE.U/B (4 pk) GDE.P GDE.P/B (4 pk) GDE.Q/B 6-ft cable ( pk) GDE.P GDE6.P GDE6.P GDE6.P/B (4 pk) GDE6.P GDE64.P GDE66.P GLB.P GLB.P GLB6.P GLB6.P GLB6.P GLB64.P GLB66.P NOTE: Place the actuator on the damper shaft so that the front of the actuator is accessible. The label is on the front side.. Determine whether the damper blades will rotate clockwise or counterclockwise to open. See Figure.. If the blades will rotate counterclockwise, slide the manual override switch to manual, and move the adjustment lever to the right. Return the switch to automatic. See Figure 9. Required Tools 4 mm hex wrench 4 mm (5/-inch) drill bit and drill Small flat-blade screwdriver Marker or pencil Estimated Installation Time minutes Warning/Caution Notations WARNING : Personal injury/loss of life may occur if you do not follow a procedure as specified. Equipment damage or loss of data may occur if you do not follow a procedure as specified. To mount a (modulating) GDE/GLB6x, set the Dual In-line Package (DIP) switches to the required positions.. To access the DIP switches, raise the tab on the lower left side of the actuator. See Figure. The factory setting is clockwise (middle switch), with a direct-acting feedback signal (right switch).. Close the tab over the DIP switches. To mount a (-positon) GDE/GLBx for counterclockwise rotation, follow the Counterclockwise Damper Rotation instructions located in the Wiring Diagrams section when wiring the actuator to the controller. Item Number: 9-67, Rev. DA Page of 7
2 Document No CLOCKWISE TO OPEN "" COUNTER CLOCKWISE TO OPEN. A /8-inch shaft adapter is provided in actuator package.. Hold the shaft insert so that the raised tabs are inserted last when placing the insert into the back of the actuator.. Proceed to Figure 6. When using a 5/8-inch shaft: EA68R only for: GDE6...P GLB6...P MODULATING only for: GDE6...P GLB6...P MODULATING Figure. Setting the Direction of Rotation. NOTE: For DIP switch setting options, see the Technical Instructions EA GDE/GLB- (55-87P5). Mounting and Installation NOTE: The GDE/GLB actuator comes with a factory installed /-inch shaft guide. If shaft size is /-inch, proceed with Figure 6. EAR Figure 5. 5/8 Ø inch shaft.. Remove factory installed /-inch guide. See Figure.. Mount actuator to shaft per Figure 6. When using a /8-inch shaft: Remove factory installed /-inch guide. See Figure. EA999R Figure. Removing /-inch Ø shaft guide for /8-in or 5/8-in shaft. EA5R Figure 6. Mounting Actuator to Damper Shaft. f 4 mm 6- lb-in (7- Nm) Torque 5 b EA679R Mounting GDE/GLB on ~ /8-inch 8... mm shafts 4 Figure 4. /8 Ø inch shaft, see Figure Item f. EA5R Figure 7. Installing the Position Indicator (b). Page of 7
3 Document No CENTER THE MOUNTING BRACKET IN THE SLOT THESE HOLES FOR USE WITH ACCESSORY KITS ONLY. DO NOT USE IN THE INSTALLATION OF DIRECT-COUPLED APPLICATIONS The auxiliary switch setting shafts rotate with the actuator. NOTE: The scale is valid only when the actuator is in the "" position on clockwise motion. / / 4 mm 5/ in. A B EA786R4 c d Figure 8. Attaching the Mounting Bracket. Manual Override To move the damper blades and lock the position with no power present, do the following:. Slide the red manual override knob toward the back of the actuator. See figure 9.. Make adjustments to the damper position.. Slide the red manual override knob toward the front of the actuator. Once power is restored, the actuator returns to automated control. ADJUSTMENT LEVER d EA66R AUX SWITCH ADJUSTMENT Figure. Auxiliary Switch Setting Dial. Mechanical Range Adjustment EA55R 4 mm EA56R < Figure. Moving the Mechanical Range Stop.. Loosen the stop set screw.. Move it along the track to the desired position, and fasten it in place. PLR AUTO MANUAL Figure 9. Manual Override. Mechanical Range Limitation and Self adapt Feature. To use the entire to V input signal to control the adjusted range, raise the tab located on the lower left-hand side of the actuator and locate the DIP switches. See Figure. Dual Auxiliary Switch Setting For GDE/GLB 6x, GDE/GLB64x and GDE/GLB66x only. Factory setting: A = 5 B = 85 Use a flat-blade screwdriver to adjust the A switch. The long arm of the points to the setting. Manually turn the red ring of the B switch. The narrower tab on the ring points to the setting. See Figure.. Set the self-adapt DIP switch to (ON).. Close the tab over the DIP switches. For example, if you set the locking screw at 7 and turn the self-adapt switch ON, a 5V input signal will drive the damper to 5 (5% of its adjusted range). Page of 7
4 Document No EA8R Figure. Self-adapt Switch in the On Position. Factory setting (OFF) When turning the self-adaptive feature on, or after software reset with the feature on, the actuator will enter a five-minute calibration cycle as the actuator adjusts to the rotation limits of the system. The software reset happens after power on, or may be caused by electrostatic discharge (ESD) at levels of kv and above. Slope (span) and Offset adjustment For GDE/GLB6x and GDE/GLB64x only Factory setting: Slope (span) ΔU Offset Uo = Use a flat-blade screwdriver to make adjustments. The long arm of the points to the setting. EA6R Ys Uo U V SLOPE, U 4 6 OFFSET, Uo 5 4 Figure. Wiring All wiring must conform to NEC and local codes and regulations. Use earth ground isolating step-down Class transformers. Do not use autotransformers. Determine the supply transformer rating by summing total VA of all actuators used. It is recommended that one transformer power no more than actuators. WARNING: Installations requiring Conformance All wiring for CE rated actuators must only be separated extra low voltage (SELV) or protective extra low voltage (PELV) per HD Use safety-isolating transformers (Class III transformer) per EN They must be rated for % duty cycle. Overcurrent protection for supply lines is maximum A. Wiring Diagrams GDE/GLBx Counterclockwise Damper Rotation of GDE/GLBx If the damper blades turn counterclockwise to open (CCW), reverse the 6 (violet) and 7 (orange) wires at the controller. Do not wire different types of actuators (such as GBB or GIB actuators) in parallel with these models. NOTE: (For GDE/GLB floating control actuator series only) To prolong actuator life, use a controller and/or software that provide a time-out function. This function removes the actuator drive signal after the signal has been on for a predefined time. Page 4 of 7
5 Document No GDE/GLBx, Continued Each wire has the standard symbol printed on it. See Table. 4 Vac Power Supply Floating Control. 6 7 P P P S S4 Standard Symbol Table. -position Control 4 Vac. Function Terminal Designation Color Supply (SP) G Red 6 Control signal clockwise Y Violet 7 Control signal Y Orange counterclockwise EA8R M NEUT 4 Vac A S S 7 (ORANGE) 6 (VIOLET) (RED) EARTH GROUND ISOLATING CLASS TRANSFORMER FOR 4 Vac POWER : SAFETY ISOLATING TRANSFORMER PER EN 674 B S5 S6 S Switch A Common Q Gray/red S Switch A N.C. Q Gray/blue S Switch A N.O. Q4 Gray/pink S4 Switch B Common Q Black/red S5 Switch B N.C. Q Black/blue S6 Switch B N.O. Q4 Black/pink P Feedback Potentiometer a White/red to % P - P P Feedback Potentiometer b White/blue Common P Feedback Potentiometer c White/pink to % P - P EA65R Vac Figure 4. Floating Control. Each wire has the standard symbol printed on it. See Table. Standard Symbol Table. Modulating Control. Terminal Designation GDE/GLB6x Function 4 Vac Power Supply, Modulating Control Supply (SP) G Red Color 8 M Neutral (SN) G Black 8 to V input signal Y Gray 9 Output for to Vdc position indication U Pink EA9R Factory installed options S Switch A Common Q Black S Switch A N.C. Q Black S Switch A N.O. Q4 Black S4 Switch B Common Q Black S5 Switch B N.C. Q Black S6 Switch B N.O. Q4 Black Figure 5. to Vdc Modulating Control. Page 5 of 7
6 Document No Retrofit Wiring Modulating Control ( to Vdc) Siemens GDE Series GLB Series Belimo LMB Series NMB Series Honeywell MN755 Series MN75 Series* Johnson M94 Series M99 Series* Function Color Number Color Number Color Number Color Number Supply 4V Red Red Red Red Common Black Black Black Black () to Vdc Input Gray 8 White Brown Gray () to Vdc Feedback Pink 9 Orange 5 Blue 5 Orange 4 NOTE: MN75 Series is not available precabled. Numbers listed associate with terminal positions. M99 Series is not available precabled. Numbers listed associate with terminal positions. Floating Control Siemens GDE Series GLB Series Belimo LMB Series NMB Series Honeywell MN65 Series MN6 Series* Johnson M94 Series M99 Series* Function Color Number Color Number Color Number Color Number Common Red Black Black Black 4V CW Violet 6 Red Red Red 4V CCW Orange 7 White White 4 Orange NOTE: MN6 Series is not available precabled. Numbers listed associate with terminal positions. M99 Series is not available precabled. Numbers listed associate with terminal positions. References EA GDE/GLB P5 OpenAir Electronic Damper Actuators GDE/GLB Series Non-spring Return Rotary 4 Vac Modulating Control EA GDE/GLB P5 OpenAir Electronic Damper Actuators GDE/GLB Series Non-spring Return Rotary 4 Vac Three-Position Control Page 6 of 7
7 Document No Dimensions 7/6 () min. 4 inch mm / (.8) / () 5/ () min. /4 inch 6 mm min. 8 inch mm 5-7/6 (7) -7/6 (87) 6-5/8 (68) 7-/6 (8) 5/6 (94) -/8 (6) min. -/8 inch 6 mm 5/ (4) EA5R min. inch 5 mm min. /8 inch mm /6 () EA5R -/4 (7) Figure 6. Dimensions of the OpenAir GDE/GLB Actuator and Mounting Bracket. Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. OpenAir is a trademark of Siemens Schweiz, AG. Product or company names mentioned herein may be the trademarks of their respective owners. Building Technologies Division Deerfield Parkway Buffalo Grove, IL 689 USA Your feedback is important to us. If you have comments about this document, please send them to sbt_technical.editor.us.sbt@siemens.com Document No Printed in the USA Page 7 of 7
Use. Functions. OpenAir TM. Linear version, modulating, AC 24 V
4 666 OpenAir TM Air damper actuators Linear version, modulating, AC 24 V GBB16...2 Electromotive linear actuators, DC 0...10 V modulating control signal, nominal force 440 N, operating voltage AC 24 V,
More informationTEC VAV with 0-10V AO Heat. Modulation and CO2 Monitoring. Controller. Control Applications. Product Description. Accessories.
Document No. 540-1031 TEC VAV with 0-10V AO Heat Modulation and CO2 Monitoring Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2843,
More informationSiemens TEC Extended I/O Controller
Document No. 540-1028 TEC Extended I/O Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2497 Product Description These instructions explain
More information599 Series Zone Valve Actuator SF Series Electronic Valve Actuator, 2-position Control
599 Series Zone Valve Actuator SF Series Electronic Valve Actuator, 2-position Control Technical Instructions EA1021R1 Description The 599 SF Series electronic zone valve actuators, accepts 24 Vac, 120
More informationTEC Heat Pump Multi-Stage Controller. Control Applications. Accessories. Product Description. Product Numbers. Warning/Caution Notation
Document No. 540-1024 TEC Heat Pump Multi-Stage Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2273 and 2274 Product Description These
More informationSQM5 Reversing Actuators, with Multiple Analog Control Input Signals
Document No. 9-4 January 8, 8 SQ5 Reversing Actuators, with ultiple Analog Control Input Signals Product Description Reversing actuator used to position flow control valves, butterfly valves, dampers,
More informationBACnet PTEC Heat Pump Multi-Stage Controller. Control Applications. Product Description. Product Numbers. Warning/Caution Notation
BACnet PTEC Heat Pump Multi-Stage Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 6673, 6674 Product Description These instructions explain
More informationAir damper actuators
4 604 OpenAir Air damper actuators Rotary version, AC/DC 24 V and AC 230 V GQD...1 GQD 1 Electric motor-driven actuators for two-position and three-position control as well as DC 0 10 V control 2 Nm nominal
More information599 Series Zone Valve Actuator SF Series Electronic Valve Actuator, 2-position Control
599 Series Zone Valve Actuator SF Series Electronic Valve Actuator, 2-position Control Technical Instructions Tuesday, August 18, 2009 EA1021R1 Description The 599 SF Series electronic zone valve actuators,
More informationPowermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Floating Control
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Floating Control Document No. 55-34P25 EA 599-6 October 7, 28 EA57R Description Features Application Product Numbers The Powermite 599 MT Series
More informationTEC Unit Conditioner Controller
Document No. 540-1026 TEC Unit Conditioner Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2040 and 2041 2050 through 2054 Product Description
More informationCables. U.S. Registered Trademark EN0B-0341GE51 R0402 Copyright 2002 Honeywell Inc. All rights reserved
N20010/N34010 NON-SPRING RETURN DAMPER ACTUATOR 20/34 Nm (177/300 lb-in) FOR MODULATING CONTROL PRODUCT DATA GENERAL These direct-coupled damper actuators provide modulating control for: air dampers, VAV
More informationSQM5 Reversing Actuator with Analog Input Signal
Document o. 129-4 June 1, 25 SQ5 Reversing Actuator with Analog Input Signal Product Description Reversing actuator used to position flow control valves, butterfly valves, dampers, or any application requiring
More informationBACnet PTEC Terminal Box (VAV) Controller. Control Applications. Product Numbers. Product Description. Warning/Caution Notation
BACnet PTEC Terminal Box (VAV) Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 6600 through 6607 Product Description These instructions
More informationTEC Terminal Box (VAV) Controller
Document No. 540-1025 TEC Terminal Box (VAV) Controller Generic Controller I/O Layout. See Wiring Diagram for application specific details. Control Applications 2020 through 2027 Product Description These
More informationPowermite 599 MT Series SAS Electronic Valve Actuator 24 Vac or 24 Vdc, Proportional Control
Powermite 599 MT Series SAS Electronic Valve Actuator 24 Vac or 24 Vdc, Proportional Control Description Features Application The Powermite 599 MT Series SAS Electronic Valve Actuator requires a 24 Vac
More informationActuator Commissioning Tool
Document No. 129-287 Actuator Commissioning Tool Product Description The 985-047 Actuator Commissioning Tool provides a portable instrument for exercising, calibrating, and testing resistive, proportional
More informationRotary version, three-position control
4 622 Residential Air damper actuators GXD..31.1 Rotary version, three-position control Electric motor-driven actuators for three-position control 1.5 Nm nominal torque AC 24 V or AC 230 V rated voltage
More informationBACnet PTEC Unit Conditioner/Fan Coil P. Controller. Control Applications. Accessories. Product Description. Warning/Caution Notation
Installation Instructions BACnet PTEC Unit Conditioner/Fan Coil Controller Figure 1. BACnet PTEC Unit Conditioner/Fan Coil Controller. Control Applications 6540, 6541, 6550, 6551, 6552, 6553 and 6554 Product
More informationRoom Pressurization Controller Electronic Output
Document No. 540-1033 Room Pressurization Controller Electronic Output Product Description These instructions explain how to field install or replace a Room Pressurization Controller (RPC) Electronic Output
More informationFree Energy Band RCC30U Room Temperature Controller for Four-pipe Fan Coil Unit
Document No. 155-324 Free Energy Band RCC30U Room Temperature Controller for Four-pipe Fan Coil Unit Description Features Application Product Number Room temperature controller for four-pipe fan coil units.
More informationOpenAir Rotary actuators with spring return GCA 1 Technical basics. Edition 2.2 CE1Z4613en Building Technologies HVAC Products
OpenAir Rotary actuators with spring return GCA 1 Technical basics Edition 2.2 CE1Z4613en 04.09.2006 Building Technologies HVAC Products 2/36 HVAC Products 04.09.2006 Contents 1 Introduction...5 1.1 Revision
More informationPXC Compact Unitary Equipment Controller (UEC)
Document No. 553-169 PXC Compact Unitary Equipment Controller (UEC) Product Description The PXC Unitary Equipment Controller (UEC) is an MS/TP device that can be configured as a programmable, stand-alone
More informationN20010-SER. NON-SPRING RETURN DAMPER ACTUATOR 20 Nm (177 lb-in) FOR ADJUSTABLE MODULATING CONTROL SPECIFICATIONS GENERAL FEATURES PRODUCT DATA
N20010-SER NON-SPRING RETURN DAMPER ACTUATOR 20 Nm (177 lb-in) FOR ADJUSTABLE MODULATING CONTROL GENERAL These direct-coupled damper actuators provide adjustable modulating control for: air dampers, VAV
More informationCOMMERCIAL. VAM24-90-(A) Series
MERCIAL Bray Controls Commercial Division 13788 West Road, Suite 200A Houston, Texas 77041 BCDSales@Bray.com Phone: 1-888-412-2729 Fax: 1-888-412-2720 www.braycommercialdivision.com Installation Instructions/Part
More informationTerminal Equipment Controller Enclosure
Document No. 550-196 Terminal Equipment Controller Enclosure Product Description A Terminal Equipment Controller enclosure is a general-purpose metal cabinet with a removable cover that houses an electronic
More informationLTEC Heat Pump DDC Controller
Document No. 09 Rev., May, 00 LTEC Heat Pump DDC Controller Product Description These instructions explain how to install or replace a LTEC (LonMark Terminal Equipment Controller) HP (Heat Pump) DDC Controller
More informationN20, N34 Series Non-Spring Return Direct Coupled Actuators
N0, N Series Non-Spring Return Direct Coupled Actuators INSTALLATION INSTRUCTIONS APPLICATION N0 and N Series Non-Spring Return Direct Coupled Actuators (DCA) are used within heating, ventilating, and
More informationN05, N10 SERIES NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR MODULATING AND FLOATING CONTROL
N, N SERIES NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR MODULATING AND FLOATING CONTROL SPECIFICATIONS PRODUCT DATA Supply voltage Nominal voltage Vac/dc -%/+%, /6 Hz Vac/dc, /6 Hz All values
More informationRoom Pressurization Controller Pneumatic Output
Document No. 540-1032 Room Pressurization Controller Pneumatic Output Product Description These instructions explain how to field install (pages 1 through 3) or replace (pages 3 through 4) a Room Pressurization
More informationN20010, N NON-SPRING RETURN DAMPER ACTUATOR 20/34 Nm (177/300 lb-in) FOR MODULATING CONTROL SPECIFICATIONS GENERAL FEATURES PRODUCT DATA
N21, N341 NON-SPRING RETURN DAMPER ACTUATOR 2/34 Nm (177/3 lb-in) FOR MODULATING CONTROL SPECIFICATIONS Supply voltage Nominal voltage PRODUCT DATA 24 Vac 2%, 5/6 Hz; 24 Vdc -1...+2% 24 Vac, 5/6 Hz; 24
More informationCOMMERCIAL. VAM24-90-(A) Series Installation Instructions
MERCIAL VAM24-90-(A) Series Installation Instructions Bray Controls Commercial Division 13788 West Road, Suite 200A Houston, Texas 77041 BCDSales@Bray.com Phone: 1-888-412-2729 Fax: 1-888-412-2720 www.braycommercialdivision.com
More informationFast running actuators for air dampers
4 608 OpenAir TM Fast running actuators for air dampers Fast runner rotary version, GAP19 Electronic actuator for 2-position, 3-position, or modulating control, nominal torque 6 Nm, at 2 s running time,
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
Technical data sheet NKQ24A- SuperCap rotary actuator with emergency control function and extended functionalities for adjusting dampers in technical building installations and in laboratories Air damper
More informationOpenAir Rotary damper actuators without spring return GDB/GLB Technical basics
OpenAir Rotary damper actuators without spring return GDB/GLB Technical basics CE1Z4634en 2016-07-29 Building Technologies Issued by Siemens Switzerland Ltd Building Technologies Division International
More informationAir Damper Actuators Modbus RTU
s OpenAir Air Damper Actuators Modbus RTU GEB.., GIB.. Non-spring return types Damper actuators 15 Nm / 35 Nm (non-spring return) with Modbus communication GEB.. 15 Nm nominal torque GIB.. 35 Nm nominal
More informationTRUNK TX RX + - S + - S DO LEDS FLN TRUNK TERMINATIONS INPUT/OUTPUT TERMINATIONS TRANSMIT LED
Heat Pump Controller Single Stage COVR CONTROLLR BOARD MOUNTING HOL (2) C H DO 1 DO 2 DO 3 DO 4 DO 5 DO 6 DI 3 DI 2 FLN TX RX + - S BST RTS MOUNTING RAIL + - S TC0168R5 POWR TRMINATIONS DO LDS FLN TRMINATIONS
More informationRWD68U Universal Controller
Document No. 155-738 RWD68U Universal Controller Description Features Product Number The Universal Controller is intended for heating, air conditioning, ventilation and refrigeration in comfort control
More informationSRQ24A. Technical data. Safety notes. Rotary actuator for ball valves Torque 16Nm Nominal voltage AC/DC 24V Control: Open-close Running time 9s
SRQ24A Rotary actuator for ball valves orque 16Nm Nominal voltage AC/DC 24V Control: Open-close Running time 9s echnical data Electrical data Nominal voltage AC 24V, 50/60Hz / DC 24V Nominal voltage range
More informationNKQB24-1, NKQX24-1 On/Off, Fail-Safe, Operation, Direct Coupled, 24V
NKQB24-1, NKQX24-1 On/Off, Fail-Safe, Operation, Direct Coupled, 24V orque min. 54 in-lb for control damper surfaces up to 12 sq ft. Application For proportional modulation of dampers in HVAC systems.
More informationPowers TM Controls RL 243 MP Multi-Purpose Relay
Powers TM Controls Technical Instructions Document No. 155-042P25 RL 243-6 Description The Powers is a pneumatic auxiliary device designed to provide a variety of pneumatic control functions for the typical
More informationSiemens BACnet VAV Actuator
Technical Specification Sheet Document No. 149-481 May 30, 2012 Siemens BACnet VAV Actuator Setpoints and control parameters assigned and changed locally or remotely. Setpoints and control parameters stored
More informationVAV compact controller GDB181.1E/3 GLB181.1E/3
s 3 544 OpenAir VAV compact controller DB181.1E/3 LB181.1E/3 Series E Compact controllers for plants with variable or constant airflow Integrated high-accuracy differential pressure sensor, actuator, and
More informationLTEC Unit Ventilator DDC Controller
Document No. 09 Rev., May, 00 LTEC Unit Ventilator DDC Controller Product Description These instructions explain how to install or replace a LTEC (LonMark Terminal Equipment Controller) UV (Unit Vent)
More informationNKQB24-1, NKQX24-1 On/Off, Electronic Fail-Safe, Direct Coupled, 24V
NKQB24-1, NKQX24-1 On/Off, Electronic Fail-Safe, Direct Coupled, 24V orque min. 54 in-lb for control damper surfaces up to 12 sq ft. Application For on/off, fail-safe control of dampers in HVAC systems.
More informationRCx-xxxAx Installation. Contents. Mounting: Holes for a mounting bracket. Holes are threaded for ¼-20 and are approximately.275 deep.
RCx-xxxAx-8.09 Contents Installation pg1-3 Mounting Wiring Connecting Power and Signal Operation pg4-6 DIP Switch settings Controlling the Actuator Torque Settings Signal loss and Calibration Troubleshooting
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet NKA-DKC L Modulating SuperCap rotary actuator with emergency control function and extended functionalities for adjusting dampers in technical building installations and in laboratories
More informationP216 Series Condenser Fan Speed Controller
P216 Series Condenser Fan Speed Controller Installation Instructions P216xxx-x Part No. 24-85895-18, Rev. D Issued 27 August 2015 Applications Refer to the QuickLIT website for the most up-to-date version
More informationN20, N34 SERIES. NON-SPRING RETURN DAMPER ACTUATOR 20/34 Nm (177/300 lb-in) FOR FLOATING / 2-POSITION CONTROL SPECIFICATIONS GENERAL FEATURES
N, N4 SERIES NON-SPRING RETURN DAMPER ACTUATOR /4 Nm (77/ lb-in) FOR FLOATING / -POSITION CONTROL PRODUCT DATA GENERAL These direct-coupled damper actuators provide floating and two-position control for:
More informationAir Damper Actuators Modbus RTU
s OpenAir Air Damper Actuators Modbus RTU GMA.., GCA.. Spring return types Air Damper actuators 7 Nm / 18 Nm (spring return) with Modbus communication GMA.. 7 Nm nominal torque GCA.. 18 Nm nominal torque
More informationVAV compact controller
s 3 544 OpenAir VAV compact controller Series E GDB181.1E/3 GLB181.1E/3 Compact controllers for plants with variable or constant airflow Integrated high-accuracy differential pressure sensor, actuator,
More informationRDF Series Room Temperature Controllers
Document No. 19-49 RDF Series Room Temperature Controllers Product Description Room Temperature Controllers with LCD for twopipe (with and without an electrical heater) and fourpipe fan coil units. Installation
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet NM24A-MOD Communicative damper actuator for adjusting dampers in technical building installations orque motor 10 Nm Nominal voltage AC/DC 24 V Control modulating,, hybrid mode Conversion
More informationTechnical data sheet. Technical data
echnical data sheet LMQ4A Damper actuator for adjusting air control dampers in ventilation and air-conditioning systems for building services installations For air dampers up to approx 8 m orque 4 Nm Nominal
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet GM24A-MOD Communicative damper actuator for adjusting dampers in technical building installations orque motor 40 Nm Nominal voltage AC/DC 24 V Control modulating,, hybrid mode Conversion
More informationPower consumption In operation At rest For wire sizing
echnical data sheet Modulating damper actuator for adjusting air control dampers in ventilation and airconditioning systems for building services installations For air dampers up to approx 08 m orque Nm
More informationMCx-xxxAx Installation. Contents. Mounting: Short Instruction MCx-xxxAx Connecting Power and Signal
MCx-xxxAx-8.09 Contents Installation pg1-3 Mounting Wiring Connecting Power and Signal Operation pg4-6 DIP Switch settings Controlling the Actuator Torque Settings Signal loss and Calibration Troubleshooting
More informationAirflow Pressure Sensor
Desigo TRA Airflow Pressure Sensor DXA.S04P1... Airflow Pressure Sensor (APS) is used to measure airflow for room pressurization and fume hood control applications. Differential Pressure (velocity) is
More informationFunctional data Position indication reflective visual indicator (snap on) Communicative control Cloud: (call for clientapi )
Technical data sheet AKRB24 IP Cloud capable and communicating valve actuator for adjusting flow in commercial HVAC applications. Failsafe Power Supply AC/DC 24 V Used for CCV and LGCCV assemblies. Ethernet
More informationPP-8516 & PP Electronic Static Pressure Controllers and Transmitters for Cental Air Supply Systems General Instructions
PP-8516 & PP-8616 Electronic Static Pressure Controllers and Transmitters for Cental Air Supply Systems General Instructions Part Number PP-8516 Static Pressure Controller/Transmitter PP-8616 Static Pressure
More informationVAV compact controller KNX / PL-Link
s 3 547 OpenAir VAV compact controller KNX / PL-Link Series E GDB181.1E/KN GLB181.1E/KN Networked compact controller featuring KNX (S-mode / LTE-mode) and PL- Link capability for plants with variable air
More informationASI Systems ML5720A Series
ML5720A Series Electric Linear Valve Actuators Non-Spring Return APPLICATION The ML5720A series actuators operate standard ASI Systems valves in heating, ventilating and air conditioning (HVAC) applications.
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet MQ24A-SR Modulating damper actuator for adjusting dampers in technical building installations Air damper size up to approx. 0.8 m² Nominal torque 4 Nm Nominal voltage AC/DC 24 V Control
More informationT E M P O S O N I C S I I I INSTALLATION
T E M P O S O N I C S I I I INSTALLATION A N A L O G O U T P U T W I R I N G - A N A L O G O U T P U T S 550572 B CONNECTORS RG Connector: Pin No. Wire Color Function 1 Gray Output #1 (Displacement) *
More informationLCx-xxxAx-8.08 Linear. Installation. Contents. Mounting: Short Instruction LCx-xxxAx Connecting Power and Signal
LCx-xxxAx-8.08 Linear Contents Installation pg1-3 Mounting Wiring Connecting Power and Signal Operation pg4-6 DIP Switch settings Controlling the Actuator Power Settings pg5 Signal loss and Calibration
More informationBT300 HVAC Drives Electronic Bypass (E-Bypass) Options
BT300 HVAC Drives Electronic Bypass (E-Bypass) Options Description The BT300 Electronic Bypass (E-Bypass) Options are companion packages for the family of BT300 Variable Frequency Drives (VFDs). For information
More informationH3C S12500 Routing Switch Series
H3C S12500 Routing Switch Series Quick Installation Guide Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com Document version: APW201-20131030 Copyright 2013, Hangzhou H3C Technologies Co., Ltd. and
More informationSED2 VFD NEMA Type 3R Bypass/Air Conditioner
SED2 VFD NEMA Type 3R Bypass/Air Conditioner Description The NEMA Type 3R Bypass with Air Conditioner allows SED2 to be employed in a harsh environment. The SED2 is designed specifically for HVAC applications
More informationAV24-MFT AV24-MFT2 AV24-MFT2-C105. Power consumption In operation For wire sizing N 1700 N Control Control signal Y Operating range
echnical data sheet AV4-MF()(-C105) Multi-functional linear actuators for -way and 3-way globe valves Actuating force 500 N Nominal voltage AC/DC 4 V Control: modulating DC 0 10 V Position feedback DC
More informationASI Systems ML5740A Series
ML5740A Series Electric Linear Valve Actuators Non-Spring Return APPLICATION The ML5740A series actuators operate standard ASI Systems valves in heating, ventilating and air conditioning (HVAC) applications.
More informationS05, S10, S20 Series Spring Return Direct Coupled Actuators
S0, S0, S0 Series Spring Return Direct Coupled Actuators MS0, MS0, MS0, MS7XX, MS70, MS70, MS70, MS80, MS80, MS80 APPLICATION MSXX, MS7XX, MS7XX, MS8XX Spring Return Direct Coupled Actuators (DCA) are
More informationN05010/N10010 NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR MODULATING AND FLOATING / 2-POSITION CONTROL SPECIFICATIONS
N/N NON-SPRING RETURN DIRECT-COUPLED DAMPER ACTUATORS FOR MODULATING AND FLOATING / -POSITION CONTROL SPECIFICATIONS Supply voltage Nominal voltage PRODUCT DATA Vac/dc -%/+%, /6 Hz Vac/dc, /6 Hz All values
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet SF24A-MOD Communicative spring-return actuator with emergency control function for adjusting dampers in technical building installations orque motor 20 Nm Nominal voltage AC/DC 24 V
More informationInstallation, Maintenance and Operating Instructions
VALVCON ADC-Series CONTINUOUS DUTY, UNIVERSAL ON/OFF & MODULATING ELECTRIC ACTUATORS With U2, UL2, UL3, U4, UL4, UL5, U6, UL6 & UL7 Options With -UP In The Model Number Installation, Maintenance and Operating
More informationPEAKTRONICS MKT-118. Actuator Controls Mounting Kit ASSEMBLY DIAGRAM F B A D D I I FEEDBACK POTENTIOMETER. Asahi A92, B92, C92, S92 Actuators
PEAKTRONICS MKT- Actuator Controls Mounting Kit ASSEMBLY DIAGRAM Asahi A9, B9, C9, S9 Actuators J POT HEX NUT POT LOCKWASHER H E H E E H E H F B POT WASHER HEATER mounting holes K A D D INSULATING SHEET
More informationService Bulletin. MiTek. RoofTracker Roof Truss Roller Press. Machinery Affected: Adding an Operator Platform. Machinery Division
MiTek Machinery Division Service Bulletin Machinery Affected: Document: Title: Applies To: RoofTracker Roof Truss Roller Press SB171 Adding an Operator Platform Frames 51 and Lower Copyright 2006 MiTek.
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet LR24A-MOD Communicative rotary actuator for ball valves orque motor 5 Nm Nominal voltage AC/DC 24 V Control modulating,, hybrid mode Conversion of sensor signals Communication via BACnet
More informationFunctional data Communicative control Cloud: (call for clientapi ) Angle of rotation 90
Cloud capable and communicating valve actuator for adjusting flow in commercial HVAC applications. Non-Failsafe Power Supply AC/DC 24 V Used for CCV and LGCCV assemblies Ethernet 10/100 Mbit/s, TCP/IP,
More information845G. Description. Features. Specifications
845G The 845G is a heavy duty NEMA Type 4 and 13 single turn absolute encoder that digitizes shaft position. The absolute encoder has a unique digital output for each shaft position. The use of absolute
More informationPower consumption In operation At rest For wire sizing. Torque Inhibiting torque. 150 s / C Sound power level Motor
echnical data sheet GK24A-SR Modulating SuperCap rotary actuator with emergency setting function and extended functionalities for adjusting air dampers in ventilation and air-conditioning systems for building
More informationVAV Modular Assembly (VMA) 1410/1420
Installation Instructions Issue Date June 9, 2004 VAV Modular Assembly (VMA) 1410/1420 Application The Variable Air Volume (VAV) Modular Assembly (VMA) 1400 Series consists of configurable digital controllers.
More informationECM3000. Control Motor
No. CP-SS-1816E ECM3000 Control Motor Overview The ECM3000 is a control motor designed for various industrial equipment applications. Two models are available: 90 angular stroke motor for applications
More information9.5 nominal torque 4.5 W 16 VA. Min. 30 nominal voltage Min. 30 Nm. Reversible with switch By mounting. MIN (minimum position)
echnical data sheet EF24A- Communicative spring return actuator with emergency function for adjusting air dampers in ventilation and air conditioning systems in buildings For air dampers up to approx.
More informationPEAKTRONICS DHC-100 FEATURES. Digital High-Resolution Controller
PEAKTRONICS The Peaktronics is a high performance digital positioner intended to control AC actuators, providing 450 points of resolution with quarter turn actuators ranging from sec to 0 sec and rated
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet LM24A- Communicative damper actuator for adjusting dampers in technical building installations Air damper size up to approx. m² Nominal torque 5 Nm Nominal voltage AC/DC 24 V Control
More informationOperators Guide. Vision 3 Pan & Tilt Head. Vinten Camera Control Solutions
Operators Guide Vision 3 Pan & Tilt Head Vinten Camera Control Solutions Vision 3 Pan and Tilt Head Publication Part No. 3543-8 Issue 4 Copyright Vinten Broadcast Limited 2004 All rights reserved throughout
More informationP216. Condenser fan speed controller. Product bulletin. Features
P216 Condenser fan speed controller Product bulletin These controllers are designed for speed variation of single phase motors, especially for fan speed control on air cooled condensers. Head pressure
More informationProducts no longer available
echnical data sheet NV4-MF(-) Modulating linear actuator for -way and 3-way globe valves Actuating force 1000 N Nominal voltage AC/DC 4 V Modulating control DC 0... 10 V Position osition feedback feedbac
More informationInstallation & Operation Guide
Installation & Operation Guide Direct Digital VAV Controllers KMD-7001/7051 - VAV Terminal Units KMD-7002/7052 - Dual Duct VAV Units KMD-7003/7053 - Fan Induction Units 907-019-01C 1 Introduction This
More informationTechnical data sheets
echnical data sheets Ready-to-connect spring return actuator with emergency function for VAV and CAV units in ventilation and air conditioning systems in buildings For air dampers up to approx. 4 m 2 orque
More informationDATA SHEET Rudder/azimuth angle Transmitter CAN, RTC 300/RTC 600
DATA SHEET Rudder/azimuth angle Transmitter CAN, RTC 300/RTC 600 CANopen interface Measuring angle full +/-180 High accuracy Easy zero and CW/CCW adjustm. Continuous shaft rotation DEIF A/S Frisenborgvej
More informationFunctional data Nominal torque min. 180 in lb [20 NM] Communicative control Cloud: (call for clientapi )
Cloud capable and communicating failsafe damper actuator for adjusting dampers in commercial HVAC applications. Failsafe Air Damper Size Up to approx. 45 sq. ft. Nominal Torque 180 in lb [20 NM] Power
More informationWOODINVILLE, WA SUPERSTEP 2100 SERIES SEQUENCING PROPORTIONAL LOAD CONTROLLERS INSTALLATION & OPERATING MANUAL. Models: SLC2102-SLC2112
SELECTRONIX, INC. WOODINVILLE, WA SUPERSTEP 2100 SERIES SEQUENCING PROPORTIONAL LOAD CONTROLLERS INSTALLATION & OPERATING MANUAL Models: SLC2102-SLC2112 SLC2102X-SLC2112X SLC2152-SLC2162 SLC2170-xx Relay
More informationThe pages in this document have been extracted from a larger document and as such any page numbers are relevant only to the original document.
The pages in this document have been extracted from a larger document and as such any page numbers are relevant only to the original document. Rotary Encoder Solutions Limited Dutton Road Redwither Business
More informationJAN 16 Rev B
ANSI C136.41-2013 Rotatable Dimming Receptacles Application Specification 20 JAN 16 Rev B NOTE All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters
More informationVAV Compact Controller Modbus RTU
s OpenAir VAV Compact Controller Modbus RTU G..B181.1E/MO VAV Compact Controllers 5 / 10 Nm with Modbus communication GDB181.1E/MO with 5 Nm nominal torque GLB181.1E/MO with 10 Nm nominal torque Operating
More informationControl Motor ECM3000
No. CP SS 1816E Control Motor ECM3000 The ECM3000 is a control motor designed for various industrial equipment applications. Two models are available: 90 angular stroke motor for applications such as burner
More informationE1135C PDU and Pod Upgrade Procedure
E4030-90010 Rev. B 12/2003 In this Document... Tools Needed, 2 Contents of the Upgrade Kits, 2 Installation Procedures, 4 Verifying the Power Option of the New PDU, 4 Removing the PDU from the Support
More informationDUTY, UNIVERSAL ON/OFF & MODULATING ELECTRIC ACTUATORS
VALVCON ADC-Series CONTINUOUS DUTY, UNIVERSAL ON/OFF & MODULATING ELECTRIC ACTUATORS With U2, UL2, UL3, U4, UL4, UL5, U6, UL6 & UL7 Options With -UP In The Model Number Installation, Maintenance and Operating
More informationElectrical data Nominal voltage AC/DC 24 V Nominal voltage frequency
echnical data sheet GK24A-MF Parameterisable SuperCap rotary actuator with emergency control function and extended functionalities for adjusting dampers in technical building installations and in laboratories
More information