D1U5CS-H HA4C
|
|
- Madeleine Henry
- 6 years ago
- Views:
Transcription
1 FEATURES 2825W (220Vac) Output power Certified to Climate Savers Computing Initiative SM 80 PLUS Gold efficiency 12V Main output, 5V standby output 1U sized; dimensions 5.1 x14.4 x Watts per cubic inch density N+1 redundancy capable, including hot plugging (up to 3 in parallel) Active current sharing on main output, ORing FET Overvoltage, Overcurrent, Overtemperature protection Internal cooling fans (variable speed) I²C Bus Interface with status indicators RoHS compliant PRODUCT OVERVIEW D1U5CS-H HA4C The D1U5CS-H-2825 is a 2825 Watt, power-factor-corrected (PFC) front-end power supply for redundant systems. The main output is 12V and the standby output is 5V. Packaged in 1U low profile, it is designed to deliver reliable bulk power to servers, workstations, storage systems or any 12V distributed power architecture system requiring high power density. The highly efficient electrical and thermal design with internal cooling fans supports reliable operating conditions. The D1U5CS-H-2825 is designed to autorecover from over-temperature faults. Status information is provided with front panel LEDs, logic signals and I 2 C management interface. ORDERING GUIDE Model Number Power Output Main Output Standby Output Airflow Connector D1U5CS-H HA4C 2825W 12V 5V Back to front, variable AC front INPUT CHARACTERISTICS Voltage Operating Range Vac Frequency Hz Maximum Current 230Vac 16 Arms Inrush Current 90 Apk Power Factor At 230Vac, full load % load Efficiency (230Vac) excludes fan load 50% load % 100% load OUTPUT VOLTAGE CHARACTERISTICS Output Voltage Voltage Set Point Accuracy Line and Load Regulation Vdc 12V Ripple Voltage & Noise 1 20MHz Bandwidth 120 mv p-p Output Current A Load Capacitance µf Voltage Set Point Accuracy 5.0 Line and Load Regulation Vdc 5Vsb Ripple Voltage & Noise 1 20MHz Bandwidth 50 mv p-p Output Current 0 4 A Load Capacitance µf OUTPUT CHARACTERISTICS Startup Time AC ramp up 1.5 s PS_On activated 150 ms Transient Response 12V Ramp 1A/μs load capacitance is 2200μF ±600 5Vsb Ramp 1A/μs load capacitance is 200μF ±250 mv Current sharing accuracy (up to 3 in parallel) At 100% load ±10 % Holdup Time 12 ms Remote Sense 20% load mv For full details go to 1 Ripple and noise are measured with 0.1 µf of ceramic capacitance and 10 µf of tantalum capacitance on each of the power supply outputs. A short coaxial cable with 50ohm scope termination is used. CB Test Certificate and Test Report D1U5CS-H HA4C.A01 Page 1 of 5
2 ENVIRONMENTAL CHARACTERISTICS Storage Temperature Range Non-condensing Operating Temperature Range 0 50 C Operating Humidity Non-condensing Storage Humidity 5 90 % Shock 30G non operating Sinusoidal Vibration 0.5G, Hz Calculated per Telecordia SR322M1C2 MTBF Ta = 30 C Ta = 40 C Acoustic ISO , ,059 c-csa-us (CSA /UL , Second Edition Safety Approvals: TUV EN :2006+All EN6950-1:2006+A11 CB Report IEC :2005(2nd ed.,) EN :2006+All Input Fuse Power Supply has internal 20A/250V fast blow fuse on the AC line input Material Flammability UL 94V-0 Switching Frequency TBD Weight 5.92lbs (2.691kg) hrs PROTECTION CHARACTERISTICS Output Voltage Overtemperature Autorestart C 12V Overvoltage Latching V Overcurrent Latching A 5Vsb Overvoltage Latching; requires AC recycling V Overcurrent Autorecovering 5 7 A Note: The main output is able to be re-enabled after OCP and OVP event by cycling PS_ON/L pin from low to high to low. ISOLATION CHARACTERISTICS Insulation Safety Rating / Test Voltage Input to Output - Reinforced 3000 Vrms Input to Chassis - Basic 1500 Vrms Material Flammability UL 94V-0 CONTROL SIGNALS Status Conditions Description Off No AC input to all PS LED Yellow Power Supply Failure Flashing Green Main Output Disabled Green Power Supply Good Status PS-ON, PGOOD, ACOK, PS_BAD, FANFAIL, OT Warning & shutdown, AC Range Output Fault 12V OV, 12V UV, 12V OC, Vsb Fail, Fan1 Warn, Fan2 Warn 12V Output 10 bit scaled output voltage 12V 10 bit scaled output current Fan1 Monitor Fan speed (RPM) Fan2 Monitor Fan speed (RPM) I 2 C Registers Standby Output 10 bit scaled output voltage Standby Output 10 bit scaled output current Ambient temp 10 bit ambient temperature reading HS1 temp 10 bit heatsink 1 temperature reading HS2 temp 10 bit heatsink 2 temperature reading VAC 10 bit scaled input voltage IAC 10 bit scaled input current D1U5CS-H HA4C.A01 Page 2 of 5
3 EMISSIONS AND IMMUNITY Characteristic Description Criteria Harmonics IEC/EN Voltage Fluctuation and Flicker IEC/EN Emission Conducted FCC 47 CFR Parts 15/CISPR 22/EN55022 Class A, 4dB margin Emission Radiated FCC 47 CFR Parts 15/CISPR 22/EN55022 Class A ESD IEC/EN kV contact discharge 8kV operational air discharge 15kV non-operational air discharge Electromagnetic Field IEC/EN Electrical Fast Transients/Burst IEC/EN Surge IEC/EN kV/2kV, Performance Criteria B RF Conducted Immunity IEC/EN Vac, 80% AM, 1kHz, Performance Criteria A Magnetic Immunity IEC/EN A/m Voltage dips, interruptions IEC/EN OUTPUT CONNECTOR AND SIGNAL SPECIFICATION DC and Signal Connector: FCI PowerBlade # LF P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 x1 x2 x3 x4 x5 x6 AC_OK/H PW_OK/L +OUT +OUT D VOUT VOUT VOUT VRTN VRTN VRTN VRTN VRTN VRTN VOUT VOUT VOUT SPARE SMB/ Alert I_SHARE I 2 C ADR0 I 2 C ADR1 I 2 C ADR2 PS_KILL +OUT +OUT C PS_ Present B mate-last pins Pin Assignment Signal Name Description High Level Low Level I Max P1, P2, P3, P10, P11, P12 VOUT Main output voltage P4, P5, P6, P7, P8, P9 VRTN Main output voltage, return A1 Sense + VOUT remote sense, positive node input, connected to the +ve load point A2 Sense - VOUT remote sense, negative node input, connected to the -ve load point C5, C6, D5, D6 Standby voltage output C3, C4, D3, D4 Standby voltage, return, tied internally to Output B1 I_Share Active load sharing bus 0 8V -4 ma / +5 ma D1 AC_OK/H Input AC Voltage OK signal output (open drain with internal pull up of 10kΩ to Vsb) D2 PW_OK/L Power OK signal output (open drain with internal pull up of 10kΩ to Vsb) >2.5V <0.8V >2.5V <0.8V C2 SMB/Alert SMB/Alert signal output (open collector) B5 PS_Kill Floating pin will turn off P/S (shorter pin, last-make and first-break contact >2.1V (open) for hot plugging). This signal overrides PS-On in disabling the Main Output <0.8V (active, PS:On) B6 PS_Present Internally tied to Vsb return 0 V A6 PS_On/L Internal 5.11KΩ pull-up to Vsb, (accepts open collector/drain drive). This signal to be pulled low to turn-on main output of power supply A3 I 2 C Data I 2 C serial data bus; internal 4.64kΩ pull-up to 3.3V A4 I 2 C Clock I 2 C serial clock bus; internal 4.64kΩ pull-up to 3.3V B2 I 2 C Adr0 Address input 0, internal 10kΩ pull-up to Vsb B3 I 2 C Adr1 Address input 1, internal 10kΩ pull-up to Vsb B4 I 2 C Adr2 Address input 2, internal 10kΩ pull-up to Vsb SENSE + SENSE - I 2 C DATA I 2 C CLOCK SPARE PS_ON/L A -32mA -32mA N/A D1U5CS-H HA4C.A01 Page 3 of 5
4 DC OUTPUT RIGHT ANGLE CONNECTOR IN POWER SUPPLY (viewed from end of power supply) dfdj DC OUTPUT VERTICAL CONNECTOR MATE ON BACKPLANE (backplane view) D1U5CS-H HA4C.A01 Page 4 of 5
5 MECHANICAL DIMENSIONS Airflow Back to Front AC Input Connector: The AC input connector is standard IEC320 C20 (20A). Dimensions: 5.1 x 14.4 x 1.61 [129.5mm x 367mm x 41mm] D1U5CS MATING CONNECTORS 12V D1U5CS mating connector Press Fit Solder 1 Straight Right Angle Straight Right Angle MPS TBD TBD TBD FCI LF TBD TBD 1 Solder connector recommended for board thickness of <0.090 OPTIONAL ACCESSORIES Description 12V D1U5CS Connector Card Part Number D1U5CS-12-CONC APPLICATION NOTES Description 12V D1U5CS Connector Card D1U5CS-H HxxC Communication Protocol D1U EEPROM Specification Application Note ACAN-41 ACAN-40 ACAN-37 Murata Power Solutions, Inc. 11 Cabot Boulevard, Mansfield, MA U.S.A. ISO 9001 and REGISTERED This product is subject to the following operating requirements and the Life and Safety Critical Application Sales Policy: Refer to: Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice Murata Power Solutions, Inc. D1U5CS-H HA4C.A01 Page 5 of 5
D1U4CS-W HxxC Series AC/DC Front End Power Supply
PRODUCT OVERVIEW The D1U4CS-W-2200-12-HxxC is a 2200 Watt, power-factor-corrected (PFC) front-end power supply for hot-swapping redundant systems. The main output is 12V and standby output of 5V. Packaged
More informationD1U-W Hx Series
www.murata-ps.com PRODUCT OVERVIEW The D1U-W-1600 is a 1600 Watt, power-factor-corrected (PFC) front-end power supply for hot-swapping redundant systems. The main output is 48V and standby output of either
More informationD1U-W Hx Series
www.murata-ps.com D1U-W-2000-48-Hx Series PRODUCT OVERVIEW The D1U-W-2000 is a 2000 Watt, power-factor-corrected (PFC) front-end power supply for hot-swapping redundant systems. The main output is 48V
More informationC1U-W Tx Series
www.murata-ps.com PRODUCT OVERVIEW The C1U-W-1200 is a 1200 Watt universal AC input, power-factor-corrected (PFC) front-end power supply for general applications. The main output is 12V with a standby
More informationC1U-W Tx Series AC/DC Front End Power Supply
www.murata-ps.com PRODUCT OVERVIEW The C1U-W-1200 is a 1200 Watt universal AC input, power-factor-corrected (PFC) front-end power supply for general applications. The main output is 48V with a standby
More informationD1U3CS-W HxxC Series
www.murata-ps.com D1U3CS-W-1200-12-HxxC Series PRODUCT OVERVIEW The D1U3CS-W-1200-12-HxxC series are 80 PLUS Gold efficiency 1200 watt, power factor corrected front end supplies with a 12V main output
More informationD1U3CS-D HxxC Series 81mm 1U Front End DC-DC Power Supply Converter
www.murata-ps.com PRODUCT OVERVIEW The D1U3CS-D-850-12-HxxC series are highly effi cient 850 watt, DC input front end supplies with a 12V main output and a 3.3V (20W) standby. They have active current
More informationD1U2-D HA4C 54mm 1U Front End DC-DC Power Supply Converter
www.murata-ps.com D1U2-D-400-12-HA4C PRODUCT OVERVIEW The D1U2-D-400-12-HA4C is a 400 watt, DC input, isolated front end power supply with a 12V main output and a 5V (15W) standby. It features active current
More informationD1U54-HD HA4C 54mm 1U Front End HVDC Power Supply Converter
PRODUCT OVERVIEW The D1U54-HD-1200-12-HA4C is a high efficiency 1200 watt, HVDC input front end supply with a 12V main output and a 5V (3A) standby. It has active current sharing and up to 8 supplies may
More informationMVAD040 Series 40W 2" x 4" AC-DC Power Supply Converter
www.murata-ps.com MVAD040 Series DESCRIPTION The MVAD040 series switching power supplies utilize advanced component and circuit technologies to deliver high effi ciency. Designed for Medical, Telecom,
More informationSFP450-12BG AC-DC Front-End Data Sheet 12V Output, 450 Watts
Features RoHS compliant for all six substances Wide input voltage range (90-264 VAC) with PFC High power density, 9 Watts/cubic inch 1U or 2U height configurations Active current share with ORing FET I
More informationD1U54-D HxxPC Series 54mm 1U Front End DC-DC Power Converter PRODUCT OVERVIEW FEATURES
www.murata-ps.com FEATURES 1200W output power (no derating across the full DC input voltage range) 1.57"(1U) x 12.65" x 2.15" 92% effi ciency 12VDC Main output 3.3VSB or 5VSB output (20W) >28W/in 3 power
More informationThe ATF YE meets UL/CSA and all international safety requirements. CE mark is pending. Min Typ Max
ATF-1200-12-YE 12V Output, 1200 Watts AC Front End FEATURES Wide input voltage range (90-264VAC) with active power factor correction 1.64 max. height Active current share with ORing FET 5VDC @ 2A Auxiliary
More informationThe SFP BG meets international safety requirements and is CE marked to the Low Voltage Directive (LVD). Datacom Distributed Power Systems
Ideal server form factor optimizes, space, efficiency, and load variations High efficiency maximized between 30-80% load conditions Unconditionally stable under any load condition Wide input voltage range
More informationThe APR YE meets UL/CSA and all international safety requirements. It is SELV. Min Typ Max 90
APR-12-12-YE 12V Output, 12 Watts AC Front End FEATURES Wide input voltage range (9-264VAC) with active power factor correction Active current share Full protection; overvoltage, overcurrent and overtemperature
More informationD1U54P-W HxxTC Series
FEATURES +1500W continuous output power IEC60320-C16 connector for maximized low line operation 94% efficiency at 50% Load 12V main output 3.3V; 5V and 12V standby output Options 1U height: 2.15" x 12.65"
More information48V 2KW 1U AC-DC Power Supply PS Electrical Specification for: Telkoor Model:
Electrical Specification for: Telkoor Model: 48V 2KW 1U AC-DC Power Supply PS-2048 SCALE RELEASE DATE 26/06/11 SHEET 1 OF 11 REVISION HISTORY Rev Level Rev Date Change Made Reason for Change Effective
More informationD1U54-D HBxC Series 54mm 1U Front End DC-DC Power Supply Converter
PRODUCT OVERVIEW The D1U54-D-650-12-HBxC products are very high efficiency DC input 650 watt front end supplies provided with a 12V main and a 12V Standby output. An active (analogue) current share characteristic
More informationD1U54-D HxxC Series
PRODUCT OVERVIEW D1U54-D-1200-12-HxxC series are highly efficient 1500 watt, DC input front end power modules with a 12V main output and a choice of 3.3V, 5V or 12VDC (30W max) standby rail. The power
More informationSeries AMEL20-AZ 20 Watt AC-DC / DC-DC Converter
FEATURES: Click on Series name for product info on aimtec.com Models Single output Model Input Voltage (/Hz) Input Voltage (VDC) Max wattage (W) Voltage (V) Current max (A) Maximum capacitive load (µf)
More informationSafety Standards. Model Number: Unit Weight:
MEA-250A24C Highlights & Features Meet Efficiency Level VI Safety Approvals to IEC 60601-1 3.1 Ed. & IEC 60950-1 Compliant with IEC 60601-1-2 3 th and 4 th Ed. Requirements IP22 ingress protection rating
More informationAEA400S-4 Power Supply Product Specification. An APM Electronics USA, Inc. 400W Power Supply Specification For Standard PS2 Mini Redundant PSU
AEA400S-4 Power Supply An 400W Power Supply Specification For Standard Mini Redundant PSU SPECIFICATION Model Name: AEA400S-4 Rev: Description Author / Editor Date 1.0 Initial Engineering Specification
More informationConstant Voltage Mode
FEATURES: AC Input 1~277VAC Built-in Active PFC Function Protection: SCP / OVP / OTP Flicker Free High Operating Ambient Temp.: -3 ~+6 Surge protection: L-N 4KV, L-FG/N-FG 8KV Safety: UL 875 / PSE EMI:
More information300 WATT, PFC, OPEN FRAME POWER SUPPLIES TABLE 1. OUTPUT RATINGS AND SPECIFICATIONS, RMW 300W SERIES
INSTRUCTION MANUAL KEPCO An ISO 9001 Company. 300 WATT, PFC, OPEN FRAME POWER SUPPLIES RMW 300W SERIES I INTRODUCTION SCOPE OF MANUAL. This instruction manual covers the installation and operation of the
More informationElectrical Specifications VAC/390 VDC, Universal (Derate from 100% at 100V AC to 77% at 80V AC)
180 Watt Industrial Features 4 x 2 x 0.75 Inches Form factor 180 Watts with Forced Air Cooling Efficiencies upto 92% -40 to 70 degree operating temperature* 12V / 0.5A Fan Output, Thermal Shut-Down feature
More informationCLP0224 SERIES 200 Watt Open Frame Power Supply Measures: 4.00 x 2.00 x 1.40
CLP0224 Open Frame Power Supply Applications Industrial equipment Telecommunications equipment Features Compact size 50.8 mm x 101.6 mm x 35.6 mm (2 in x 4 in x 1.4 in) with density of 18 W/in 3 Universal
More information48V 1.5KW 1U AC-DC Power Supply Electrical Specification for: Telkoor Model: 0/ 7 SHEET 1 OF 1
Electrical Specification for: 48V 1.5KW 1U AC-DC Power Supply Telkoor Model: 900-1548-0000 0/ 7 SHEET 1 OF 1 REVISION HISTORY Rev Level A B Rev Date Change Made Reason for Change Effective Approved 22/06
More informationVER05 Series. xxx Series. 5 Watt. AC-DC Power Supplies. Models & Ratings. Input. Output
5 Watt xxx Series Energy Efficiency Level VI Barrel Jack & USB Versions Interchangeable Mains Connectors Included Universal Input Output Voltages from 5.0 V to 12.0 V Class II Construction Low Cost B R
More informationCAN enabled The retifier can be monitored and controlled through analogue signals. It is also equipped with a CAN signal bus.
D CAR0948TN -48V/850W rectifier Product Features High power density: 19.2W / inch delta; 1160W/L Constant output power Fits in 19 high, ETSI compliant Wide input range (90VAC 280VAC) Outdoor operating
More information12-15VDC (12V±5%) 24-28VDC (24V±5%)
Features Description Universal AC input (85-264VAC) Long 7 year warranty Protections: SCP, OVP, OCP, OTP 1% full load burn-in test DC OK indicator LED with relay contacts cooling by free air convection,
More informationSeries AMEL5-MAZ 5 Watt AC-DC / DC-DC Converter
Click on Series name for product info on aimtec.com FEATURES: I/O Isolation 4000 Operating Temp: -40 C to +80 C or -25 C to +80 C Input: 90-264, 47-440Hz, or 130-370VDC Over load, Over, Short Circuit Protection
More informationefo Series Wide range AC/DC Single Output 1000W Rugged Power Supply Electrical Specification for: Telkoor Part Number:
Electrical Specification for: efo1000-124 Series Wide range AC/DC Single Output 1000W Rugged Power Supply Telkoor Part Number: 900-1124-1000 GENERAL SCALE RELEASE DATE 05/08/2012 SHEET 1 OF 6 Rev Level
More informationSPECIFICATION. Model: PS3038. Redundant Power Supply With Active PFC 700W + 700W
SPECIFICATION Model: PS3038 Redundant Power Supply With Active PFC 700W + 700W Toll Free: 1-888-865-6888 Tel: 510-226-8368 Fax: 510-226-8968 Email: sales@rackmountmart.com TABLE OF CONTENTS 1. General.......
More informationElectrical Specifications. Input Input range: Vac Hz, single phase AC. 92% typical at high line 50% load. FCC Subpart J EN55022 Class A
POWER Data Sheet Total Output Power: 460 Watts +12 Vdc Stand-by Output Wide Range Input Voltage: 90-264 Vac DS460S 460 Watts Special Features Active power factor correction EN61000-3-2 harmonic compliance
More informationElectrical Specifications. Input Current 115 VAC: 1 A max. 230 VAC: 0.5 A max.
MLP75 Medical Features 3 x 2 x 1 Inches Form factor 75 Watts Convection Approval to EN60601 3 rd Edition Efficiencies upto 93% -40 to 70 degree operating temperature Dual fusing Thermal Shut-Down feature
More informationUniversal Power Supplies
, Features Universal input: 90 264 VAC or 120 30 VDC Active power factor correction (>0.95) High efficiency up to 93% Load share function for up to 3 units in parallel Adjustable output voltage EMI/EMC
More informationD1U Communications D1U Communications Protocol Application Note
www.murata-ps.com D1U Communications Communication Protocol Support The D1U family of power supplies currently supports 3.3V-bus and 5V-bus standardmode (100kHz) I 2 C Serial Communication as outlined
More informationLFWLP225 SERIES 225 Watt Open Frame Power Supply Measures: 4.00 x 2.00 x 1.00
Features 4 x 2 x 1 Inches Form factor 225 Watts with Forced Air Cooling Efficiencies upto 94% -40 to 70 degree operating temperature* 12V / 0.5A Fan Output, Thermal Shut-Down feature 3.37m Hours, Telcordia
More informationElectrical Specifications. Input Input range: (1200 W) (1000 W) Hz, single phase AC. > 91% typical at high line 50% load
POWER Data Sheet Distributed Power Bulk Front-End Total Power: 1200 Watts +3.3 Vdc Stand-by Wide Range Input Voltage: 90-264 Vac DS1200 1200 Watts Distributed Power System Special Features Active power
More informationConsult with factory for availability INPUT CHARACTERISTICS. Consult with factory for details and availability OUTPUT CHARACTERISTICS
250W 3" x 5" Convection Cooled AC-DC Power DESCRIPTION The PQC250 series switching power supplies utilize advanced component and circuit technologies to deliver high efficiency and low power dissipation
More informationLFWLP350 SERIES 350 Watt Open Frame Power Supply Measures: 5.00 x 3.00 x 1.00
Features 5 x 3 x 1 Inches Form factor 350 Watts with Forced Air Cooling & 200 Watts Convection Cooling Efficiencies upto 94% -40 to 70 degree operating temperature* 12V / 0.5A Fan Output, Thermal Shut-Down
More informationElectrical Specifications VAC/390 VDC, Universal (Derate from 100% at 100V AC to 95% at 85V AC)
225 Watt Industrial Features 4 x 2 x 1 Inches Form factor 225 Watts with Forced Air Cooling Efficiencies upto 94% -40 to 70 degree operating temperature* 12V / 0.5A Fan Output, Thermal Shut-Down feature
More information12-15VDC (12V±5%) 24-28VDC (24V±5%)
Features DIN Rail Description Universal AC input (85-264VAC) Long 7 year warranty Protections: SCP, OVP, OCP, OTP 1% full load burn-in test DC OK indicator LED with relay contacts cooling by free air convection,
More informationElectrical Specifications VAC/390 VDC, Universal (Derate from 100% at 100V AC to 77% at 80V AC)
180 Watt Medical Features 4 x 2 x 0.75 Inches Form factor 180 Watts with Forced Air Cooling Approval to EN60601 3rd Edition Efficiencies upto 92% -40 to 70 degree operating temperature* Dual fusing 12V
More informationRT4B-110V/12A RECTIFIER
The RT4B-110V/12A is a switched mode rectifier (SMR) module designed to provide up to 12A of output current into a 110V nominal system. It can be used with or without a cooling fan. With a fan it runs
More informationLFMWLP225 SERIES 225 Watt Open Frame Power Supply Measures: 4.00 x 2.00 x 1.00
Features 4 x 2 x 1 Inches Form factor 225 Watts with Forced Air Cooling Approval to EN60601 3 rd Edition Efficiencies upto 94% -40 to 70 degree operating temperature* Dual fusing 12V / 0.5A Fan Output,
More informationChrome DIN Rail Power Supply 12V 9.96W 1 Phase (Class II & NEC Class 2) / DRC-12V10W1A
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
More informationSeries AMEL20-MAZ 20 Watt AC-DC / DC-DC Converter
Click on Series name for product info on aimtec.com FEATURES: I/O Isolation 4000 Energy Star compliant Operating Temp: -40 o C to +70 o C Ultra-small package Over load, Over, Short Circuit Protection Up
More informationGSP750 Series. 750 Watts. AC-DC Power Supplies. Models & Ratings. Input
C-DC Power Supplies 750 Watts 900 W Peak Power Rating for 100 ms Universal 80-264 VC Input IT & Medical Safety pprovals 1.0 W Standby Power -40 C to +70 C Operation Remote On/Off 5 V/3 Standby Output 3
More informationOutput Voltage* (nom.)(adjustable)
Industrial Power Supplies TBLC Series, 6 90 W Low profile case, module depth only 55 mm Suitable for mounting in domestic installation panels Very high efficiency and low standby power -> compliance to
More informationRT4F-110V/25A RECTIFIER
The RT4F-110V/25A is a hot-pluggable switched mode rectifier (SMR) module designed to provide up to 25A of output current into a 110V nominal system. Examples of such systems are 60 cells lead acid (136V
More informationRT12-240V/2.4kW Rectifier Specification
The RT12-240V/2.4kW is a switched mode rectifier (SMR) module that delivers up to 2.4kW of output power (and up to 11A output current) into a 240V nominal DC system. The RT12 suits AC supply voltages between
More informationIndustrial Power Supplies
, Rugged metal case for harsh industrial environments Industrial operating temperature range: 25 C to +70 C Overload and and overtemperature protection Power boost up to 120 % Power-Good signal Shock and
More informationGE Data Sheet 2.0. CLP0448 Open Frame Power Supply Vac input; 48/54Vdc output; 450W Output Power. Features. Applications.
2.0 Applications Industrial equipment Telecommunications equipment Description Features Compact size 76.2 mm x 127 mm x 35 mm (3 in x 5 in x 1.38 in) with density of 21.4 W/in 3 Universal AC Input Range
More informationChrome DIN Rail Power Supply 24V 10W 1 Phase (Class II & NEC Class 2) / DRC-24V10W1A
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
More information(877) CPCI-6U Series. Input Voltage Range AC Input. Input Voltage Range 48VDC Input. Input Voltage Range 24/28VDC Input
(877) 634-0982 www.digipwr.com 350 650 Watt Compact PCI Power Supply Product Specification Universal AC Input with PFC, 48VDC or 24/28VDC Input Key Product Features Up to 650W 6U Cabinet Environmentally
More informationH-series (Rectifier Module)
H-series (Rectifier Module) Overview: The rectifier modules provide unprecedented power density and power levels in a true plug and play format. With a wide range of available voltages, power ratings,
More informationPOWERBOX Medline 150 EBM04 Series W Single Output AC/DC Medical Switch Mode Adaptor, Desktop Style
Features Fulfills IEC60601-1-2:2014 (EMC 4th edition) Low safety ground leakage current Wide input range 90 to 264 VAC Optional output connectors 100% burn-in Overvoltage protection Overcurrent protection
More informationChrome DIN Rail Power Supply 5V 7.5W 1 Phase (Class II & NEC Class 2) / DRC-5V10W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
More informationVEL05 Series. xxx Series. 5 Watt. AC-DC Power Supplies. Models & Ratings. Input
5 Watt xxx Series Energy Efficiency Level VI Barrel Jack & USB Versions Fixed Mains Connectors Universal Input Output Voltages from 5.0 V to 12.0 V Class II Construction Low Cost B R A N D The VEL05 series
More informationElectrical Specifications VAC/390 VDC, Universal (Derate from 100% at 100V AC to 90% at 90V AC)
WLP350 Industrial Features 5 x 3 x 1 Inches Form factor 350 Watts with Forced Air Cooling & 200 Watts Convection Cooling Efficiencies upto 94% -40 to 70 degree operating temperature* 12V / 0.5A Fan Output,
More informationThe shelf can be mounted to a 19inch or 21inch rack system using adaptor mounting brackets and is compatible with the Open Compute rack design.
SPSPFE3-0XG power-shelf solutions provide rectification, system management, and power distribution, while maintaining high reliability and offering flexibility for future expansion. The power shelf can
More informationCINT W Single Output Industrial Series
Features 2 x 4 x 1.3 Package For 1U Applications 175W w/air, 12W convection cooled Universal Input 9264 VAC Average Efficiency meets Level V Requirements Approved to CSA/EN/IEC/UL695, 2nd Edition 12V fan
More informationIS-900R2UPD8G. Redundant Power Supply. Active PFC 900W + 900W. 80+ Gold Efficiency SPECIFICATION. Revision: 1.0
IS-900R2UPD8G IS-900R2UPD8G Redundant Power Supply Active PFC 900W + 900W 80+ Gold Efficiency SPECIFICATION Revision: 1.0 727,. Phillips Drive City of Industry. CA 91748. USA http:// www.xeal.com TEL:
More informationRT4F-120V/20A-WAC RECTIFIER
The RT4F-120V/20A-WAC is a switched mode rectifier/charger module designed to provide up to 20A of output current into a 120V nominal system. This charger has been designed for use in conjunction with
More informationSSD9233-R1U 280 WATT SERVER POWER SUPPLY FAULT-TOLERANT POWER SYSTEM x 4.17 x x 106 x 41.5mm
DESCRIPTION SSD9233-R1U FAULT-TOLERANT POWER SYSTEM 10.47 x 4.17 x 1.63 266 x 106 x 41.5mm UNIPOWER s SSD9233-R1U is a 280 Watt faulttolerant power system manufactured to support high-end server and communication
More informationPART NUMBER STRUCTURE. P-DUKE Technology Co., Ltd Page 1
Medical Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger PV Railway PART NUMBER STRUCTURE M A F 150 U S 12 B - Application Package Dimension Output Input Output Output Protection
More information275 Watt Medical Ultra low profile
127 x 76 x 19 mm Form factor 275 Watts with Forced Air Cooling Approval to EN60601 3rd Edition Efficiencies upto 92% -40 to 70 degree operating temperature* Dual fusing Electrical Specifications 12V /
More informationVEL05 Series. xxx Series. 5 Watt. AC-DC Power Supplies. Models & Ratings. Input
5 Watt xxx Series Energy Efficiency Level VI Barrel Jack & USB Versions Fixed Mains Connectors Universal Input Output Voltages from 5.0 V to 12.0 V Class II Construction Low Cost BRAND The VEL05 series
More informationSafety Standards. Model Number:
080AAS12 A Highlights & Features Safety Approvals to IEC 60601-1 3.1rd ed. & IEC 60950-1 Compliant with IEC 60601-1-2 4th Ed. Requirements Low touch current (
More informationEnclosed Power Supplies
, 15 150 Watt Features Very compact metal cased power supplies High operating temperature up to 70 C Low no load power consumption
More informationCSPS-6K (Shelf Type) POWER you need POWER SHELF
CSPS-6K (Shelf Type) REV: 081418 SHELF PRODUCT FEATURES: Hot pluggable n+1 Redundancy Controlled, measured and reported by TCP/IP Modular design for accommodating high power applications 19 Inch Rack Mount
More information(877) CPCI-3U Series. Input Voltage Range AC Input. Input Voltage Range 48VDC Input. Input Voltage Range 24/28VDC Input
(877) 634-0982 www.digipwr.com 200 300 Watt Compact PCI Power Supply Product Specification Universal AC Input with PFC, 48VDC or 24/28VDC Input Key Product Features Up to 3U Cabinet Environmentally Rugged
More informationRT9-48V/1.4kW Rectifier Specification
The RT9-48V/1.4kW is a switched mode rectifier (SMR) module that delivers up to 1.4kW of output power (and up to 30A output current) into a 48V nominal DC system. The RT9 suits AC supply voltages between
More information5 x 8.5 x 1.61 Inch Form Factor. Convection Cooling Rated. Approved to EN Dual Fusing. Current Sharing. Open Frame. Peak Power Capability
The MCC600 Series of open-frame medical power supplies, with its wide universal 85-264 VAC input range, is available at 600 W of output power and a variety of single output voltages. The MCC series is
More informationWatts. xppower.com. General. Input. Environmental. EMC & Safety. Output. IT & Medical Approvals. Energy Efficiency Level V, CEC2008 & EISA 2007
AC-DC 85-50 Watts AHM Series IT & Medical Approvals xppower.com Energy Efficiency Level V, CEC008 & EISA 007
More informationOutput Voltage in Constant Voltage Mode. Model Number
Supplies LDB75 Supply Constant Voltage /Current LDB Series FEATURES Universal Input: 90-305VAC Constant Voltage/Current High Efficiency 91% Class II IP67 rated Class 2 device (UL1310) Power Factor: Typical
More informationAC-DC POWER SUPPLIES UNIVERSAL INPUT, 65 WATT MEDICAL APPLICATIONS MUI65 SERIES
AC-DC POWER SUPPLIES UNIVERSAL INPUT, 65 WATT MEDICAL APPLICATIONS 2MOPP Medical FEATURES Universal Input Range Operating Temperature Range: -25º to 80ºC (with derating) Compact Package: 2.00 3.00 1.16
More informationSeries AMES40-MAZ 40 Watt AC-DC / DC-DC Converter
FEATURES: Click on Series name for product info on aimtec.com Models Single output Model (VAC/Hz) (VDC) Output Voltage (V) Output Current max (A) Efficiency (%) AMES40-3.3SMAZ 90-264/47-440 130-370 3.3
More informationCAR0548TN. Product Features. Benefits. -48V/ 500W rectifier
-48/ 500W rectifier Product Features Constant output power Universal input No derating at low mains Extended temperature range Active load sharing Hot swap- fault tolerant Worldwide certification Benefits
More informationRT4F-48V/50A-WAC RECTIFIER
The RT4F-48V/50A-WAC is a switched mode rectifier (SMR) module designed to provide up to 58A of output current into a 48V nominal system, over a wide range of AC input voltage. This rectifier has been
More informationChrome Class II DIN Rail Power Supply 24V 10W 1 Phase (NEC Class 2 & Household) / DRC-24V10W1HZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Household appliance approvals IEC/EN 60335-1 4kV Electrical Fast Transient / Burst Universal AC input voltage
More informationCPS Industrial Power Supply
CPS Industrial Power Supply Power Supply Specification Model Number: FSAK C Series Industrial quality, 1U high, multiple output power supply AC Input: full range, active PFC. DC Output: 6 configurable,
More informationORDERING INFORMATION SEE PAGE 6
400W High Density Medical/Industrial Grade Open Frame Power Supplies Medical Safety Approval 60601-1 3rd Edition 2 MOPP Class 2 for home use medical applications (BSM400) Single output with 5V Auxiliary
More informationChrome DIN Rail Power Supply 24V 30W 1 Phase (Class II & NEC Class 2) / DRC-24V30W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power up to 55 C Power will not de-rate for the entire input voltage range
More informationPART NUMBER STRUCTURE. P-DUKE Technology Co., Ltd Page 1
Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV Railway PART NUMBER STRUCTURE T A H 450 U S 12 - F2 Application Package Dimension Output Input Output Output Protection
More informationChrome DIN Rail Power Supply 12V 72W 1 Phase (Class II) / DRC-12V100W1AZ
Highlights & Features Protection Class II, Double Isolation (No Earth connection is required) Universal AC input voltage and full power from -25 C to +55 C operation Power will not de-rate for the entire
More informationSeries AME25-JZ 25 Watt AC-DC / DC-DC Converter
FEATURES: Click on Series name for product info on aimtec.com Series AME-JZ I/O Isolation 000VAC Low Ripple and Noise Operating Temp: -0 C to +70 C Over Voltage Protection Over current Protection Up to
More informationElectrical Specification for: efo Wide range AC/DC Single 12V Output 400W Power Supply Telkoor Part Number: CUSTOMER SIZE CAGE CO
Electrical Specification for: efo400-112 Wide range AC/DC Single 12V Output 400W Power Supply Telkoor Part Number: 900-4136-0000 GENERAL SCALE RELEASE DATE PRELIMINARY SHEET 1 OF 5 REVISION HISTORY Rev
More informationApplication Package Dimension Output Input Output Output Protection Option Code Code Power Voltage Quantity Voltage Type (W) (VAC) (VDC)
Automation Datacom IPC Industry Measurement Telecom Automobile Boat Charger Medical PV Railway PART NUMBER STRUCTURE T A H 450 U S 12 - F2 Application Package Dimension Output Input Output Output Protection
More informationIndustrial Power Supplies
50-600 Watt Features Switch mode power supplies for DIN-rail mounting 6 power ranges with 2, 3, 6, 12, 20 and 24 A output current (24 VDC models) Selectable 115/ 230 VAC input Very low ripple and noise
More informationThese power supplies are ideal for telecom, datacom, industrial equipment and other applications.
The ABC60 Series of AC-DC open-frame power supplies, with its wide universal 90-264 VAC input range and high power density, is available at 60 W of output power and a variety of single and multiple output
More informationSafety Standards. Model Number:
150AAS12 F/B Highlights & Features Meet DOE Level VI and ErP Lot 7 Safety Approvals to IEC 60601-1 3.1rd ed. & IEC 60950-1 Compliant with IEC 60601-1-2 4th Ed. Requirements Low touch current (
More informationRT7-48V/6kW Specification
The RT7-48V/6kW is a 3 phase, active power factor corrected, switched mode rectifier (SMR) module designed to provide up to 6kW of output power (100A nominal) into a 48V nominal system. This rectifier
More informationPMT. Safety Standards. Model Number:
PMT Highlights & Features AC input range selectable by switch Full aluminium casing for light weight and corrosion resistant handling Built-in automatic fan speed control circuit MTBF > 700,000 hrs. as
More informationPMT. Model Number: Model Number Input Voltage Range Output Voltage Output Current PMT-5V350W1A (Selectable by Switch)
PMT Highlights & Features AC input range selectable by switch Full Aluminium casing for light weight and corrosion resistant handling Built-in automatic fan speed control circuit Wide operating temperature
More information400AUS24 B MDS AUS. MDS Medical AC-DC Open Frame 24Volt, 400Watt / MDS-400AUS24 B. General Description. Model Information. Model Numbering ```
400AUS24 B Highlights & Features Safety Approvals to IEC 60601-1 3.1rd ed. & IEC 60950-1 Compliant with IEC 60601-1-2 4th Ed. Requirements Low touch current (
More informationCLP0212 Open Frame Power Supply Vac input; 12Vdc output; 200W Output Power
Applications Telecommunications equipment Embedded Computing Storage Systems Industrial equipment Features Compact size 50.8 mm x 101.6 mm x 36.1 mm (2 in x 4 in x 1.4 in) with density of 18W/in 3 Universal
More informationChrome DIN Rail Power Supply 12V 25W 1 Phase (Class II & NEC Class 2) / DRC-12V30W1A
Highlights & Features Class II, Double Isolation (No Earth connection is required) Universal AC input voltage range and full power up to 55 C Power will not de-rate for the entire input voltage range Efficiency
More informationMPM-U653-DCF-B M/N: MPM-U653-DCF-B. 650W Medical AC / DC SPECIFICATION FOR SWITCHING POWER SUPPLY. Revision History
SPECIFICATION FOR SWITCHING POWER SUPPLY M/N: Revision History Version Date Change Items Rev. 1.0 July.21. 2017 Established. Page 1 Models & Ratings FEATURES 650W medical power supply with force air cooling.
More information