Nextiva S FD Models

Transcription

1 Nextiva S FD Models Quick Installation Guide All users should read the user manuals for complete details on installation, usage and functionality. Hardware Overview The S5120FD features a 2-Megapixel sensor. Front View Description: 1. Status LED 2. Built-in microphone 3. Lens hood 4. Lens 5. Auto Focus button Terminal Block Description: 1. Ground 2. 12V DC input 3. 24V AC input 4. 24V AC input 5. Ground 6. Dry contact input 7. Relay output 8. 12V DC output Rear View Description: 1. Terminal Block 2. RJ-45 ethernet connector 3. Audio In 4. Audio/Video Out 5. NTSC/PAL switch 6. Microphone internal/external switch 7. Hardware reset button 8. Micro SD/SDHC Card slot 9. Tilt Adjustment Screw Setting the Video Standard The Nextiva S5100 series IP cameras can run in one of two video standards (NTSC or PAL). Perform the following: 1. On the back of the device move the DIP switch to NTSC or PAL. 1

2 Installing the Nextiva S5100FD Models The Nextiva S5100FD has a sophisticated 3-axis mechanism design that offers a flexible and easy hardware installation for either ceiling or wall mount. CAUTION: Verint will not be held liable for damages to persons or property due to the improper installation of the Nextiva S5100 series IP cameras. To install on the ceiling: 1. Remove the dome cover using the supplied screwdriver. 2. Attach the supplied alignment sticker to the wall. 3. Drill three pilot holes through the three circles on the sticker into the wall. 4. Hammer the supplied plastic anchors into the holes. To install on the wall: 1. Remove the dome cover using the supplied screwdriver. 2. Attach the supplied alignment sticker to the wall. 3. Drill three pilot holes through the three circles on the sticker into the wall. 4. Hammer the supplied plastic anchors into the holes. 5. Insert the supplied three screws on each side of the camera base. 6. Secure the camera to the wall with a screwdriver. 5. Insert the supplied three screws on each side of the camera base. 6. Secure the camera to the ceiling with a screwdriver. 2

3 Powering the Nextiva S5100FD Models The Nextiva S5100FD models use 12V DC or 24V AC for power and is also Power-over-Ethernet (PoE)-compliant, allowing transmission of power and data via a single ethernet cable. CAUTION: Never use a PoE connection and a 12V DC or 24V AC connection at the same time. This may damage the device. To use a 802.3af compliant PoE kit: 1. Plug a category 5e cable into the RJ-45 connector on the side of the 2. Plug a category 5e cable into the RJ-45 connector on the side of the 2. Plug the other end of the cable into a POE ethernet switch or to the DATA&PWR port of a POE injector. 3. Plug the power supply cable to the power outlet. To use a 24V AC power supply: 1. Connect the AC power supply cable to pin 3 and 4 on the terminal block. 2. Plug a category 5e cable into the RJ-45 connector on the side of the To use a 12V DC power supply: 1. Connect the DC power supply cable to pin 1 (GND) and 2 on the terminal block. Red 3. Plug the power supply cable to the power outlet. Black 3

4 Adjusting the Field of View and Focus Based on the live image retrieved from the IP camera, you can adjust the following: viewing angle zoom factor and focus range 6. Rotate the lens to adjust the image orientation. You can rotate the lens 350º. CAUTION: When assembling the IP camera, ensure that the wiring does not get pinched when rotating the gimble. To adjust the viewing angle: 1. Connect the 1/8in (3.5mm) jack from the Video to BNC connector to the Audio/Video out connector. 2. Connect the BNC connector to a CCTV test monitor. 3. While viewing the image in the CCTV test monitor, turn the lens module left or right. You can rotate the lens module 350º. 4. Loosen the tilt adjustment screws (see callout 1 in image below) on both sides of the camera and then turn the lens module up or down. You can tilt the lens module 65º. To adjust the focus range: 1. Connect the 1/8in (3.5mm) jack from the Video to BNC connector to the Audio/Video out connector. 2. Connect the BNC connector to a CCTV test monitor. 3. Press the auto focus button. Press the button for less than two seconds to initiate a short cycle auto-focus. This corrects a view that is slightly out of focus. Press the button for more than two seconds to initiate a long-cycle auto-focus. This corrects a view that is completely out of focus. To adjust the zoom factor and focus range from the web page: 1. In a web browser, type the IP address of the Nextiva S5100 in the Address bar, and then press ENTER to view the live video. NOTE: If you are using Microsoft Internet Explorer, the first time you connect to the Nextiva S5100 IP cameras, an information bar is displayed requiring you to install the ActiveX plug-in from Verint Systems Inc. Follow the on-screen instructions to install the required plug-in. 2. While viewing the image on the web page: a. Click Zoom to automatically adjust the zoom. b. Click Focus to automatically adjust the focus. 5. Tighten the tilt adjustment screws. 4

5 Reattaching the Dome Cover Once you have adjusted the lens and the field of view and focus have been set, you can now reattach the lens hood and dome cover. To reattach the dome cover: 1. Reattach the lens hood. 2. Attach the dome cover to the camera. Setting the IP Address Once the IP camera is installed, you need to set the IP address from a computer. By default, all Nextiva S5100 series IP cameras are Dynamic Host Configuration Protocol (DHCP) enabled. If you have a DHCP server, the IP camera automatically obtains a valid IP configuration. If the DHCP configuration fails, the IP camera assigns itself a temporary IP address based on the Automatic Private IP Addressing (APIPA) format. To configure SConfigurator: 1. On a computer, download the latest version of SConfigurator from 2. Extract the executable file (SConfigurator.exe) to the desktop. 3. Double-click SConfigurator.exe to start SConfigurator. 4. In the General tab, click Program Options. 3. Secure the dome screws with a screwdriver. Make sure all parts of the camera are securely installed. 5. Select the IP address of the correct LAN interface from IP Address of the PC list. 6. Select Detect All Units on LAN. 7. Ensure that the Discovery IP Address is ; otherwise, click Broadcast. 8. In the S5100 Authentication section, type the username and password for the Nextiva S5100. NOTE: The default username and password is admin. 9. Click OK. 5

6 To set the IP address of an IP camera in DHCP mode: 1. Open SConfigurator. 2. Select the Units tab, then click Discover. In a DHCP environment, the Address column displays the IP address assigned by a DHCP server. 3. Select the S5100FD model, and click Configure. 4. In the tree view, expand the Network node and click IP. To set the IP address of an IP camera in APIPA mode: 1. Open SConfigurator. 2. Select the Units tab, then click Discover. In APIPA mode, the Address column displays an IP address that begins with and the text is red. 3. Select the S5100FD model, and double-click the device. 4. Click Yes in the Reconfigure unit dialog box asking you if you want to set a new network configuration on the unit. 5. Clear Use DHCP if it is selected. 6. In the IP Address box, type the IP address for the 5. Select Use the following IP address. 6. In the IP Address box, type the IP address for the 7. In the Subnet Mask box, type the subnet address in which the IP address belongs. 8. In the Gateway box, type the IP address of the server that acts as an access point to another network. NOTE: No gateway is required to communicates with other devices on the same subnet. 9. In the Host Name box, type a unique name for the 10. Click OK to close the dialog box. 11. Click Exit to close SConfigurator. 7. In the Subnet Mask box, type the subnet address in which the IP address belongs. 8. In the Gateway box, type the IP address of the server that acts as an access point to another network. NOTE: No gateway is required to communicates with other devices on the same subnet. 9. In the Host Name box, type a unique name for the 10. Click OK to close the dialog box. 11. Click Exit to close SConfigurator. North America: CALA: Documentation vissupport@verint.com To minimize our carbon footprint, we are removing the supporting EMEA: +44 (0) Mobile Support: +49 (0) product documentation CD that was shipped with our Nextiva Intelligent Edge Device products. To obtain the latest version of the customersupport.emea@verint.com mobilesupport@verint.com manuals, please visit: APAC: Hong Kong: Singapore: APAC_VIS_Services@verint.com 2011 Verint Video Intelligence Solutions. All Rights Reserved Worldwide. All other trademarks and product names are the property of their respective owners. Revision: A01