Warning Before Installation

Size: px

Start display at page:

Download "Warning Before Installation"

Oscar Riley
6 years ago
Views:

2 English Warning Before Installation Power off the Network Camera as soon as smoke or unusual odors are detected. Keep the Network Camera away from water. If the Network Camera becomes wet, power off immediately. Contact your distributor in the event of occurrence. Contact your distributor in the event of occurrence. Do not place the Network Camera around heat sources, such as a television or oven. Refer to your user's manual for the operating temperature. Keep the Network Camera away from direct sunlight. Do not place the Network Camera in high humidity environments. EN - 1

3 Do not place the Network Camera on unsteady surfaces. Do not touch the Network Camera during a lightning storm. Do not disassemble the Network Camera. Do not drop the Network Camera. Do not insert sharp or tiny objects into the Network Camera. EN - 2

4 English 1 Package Contents IP8162/62P Power Adapter Camera Stand CS-mount Lens Quick Installation Guide Software CD Warranty Card L-type Hex Key Wrench EN - 3

5 2 Physical Description Front Panel Light Sensor Lens Built-in Microphone Back Panel Status LED Audio Out BNC Video Out Microphone In External/Internal MIC Switch Ethernet 10/100 RJ45 Socket Recessed Reset Button Lens SD/SDHC Card Slot NTSC/PAL Switch Power Cord Socket General I/O Terminal Block Focus Assist Button DC-iris Control Cable Socket (IP8162) P-iris Control Cable Socket (IP8162P) Focus Controller Zoom Controller EN - 4

6 POWER COLLISION LINK RECEIVE PARTITION English 3 Mounting the Lens to the Camera 1. Mount the lens by turning it clockwise onto the camera mount until it stops. If necessary, turn the lens counterclockwise slowly until it gets the best attitude. 2. Connect the DC-iris control cable to the socket. (IP8162) Connect the P-iris control cable to the socket. (IP8162P) 1 2 For further setup, please refer to the lens instruction manual inside the lens package. 4 Network Deployment General Connection (without PoE) 1. If you have external devices such as sensors and alarms, connect them to the general I/O terminal block. 2. Connect the camera to a switch via Ethernet cable. 3. Connect the power cable from the Network Camera to a power outlet : Power +12V 2: Digital output 3: Digital input 4: Ground 5: AC 24V 6: AC 24V 7: RS485+ 8: RS485- Ethernet Switch EN - 5

7 POWER COLLISION LINK RECEIVE PARTITION POWER COLLISION LINK RECEIVE PARTITION Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. PoE Switch When using a non-poe switch Use a PoE power injector (optional) to connect between the Network Camera and a non-poe switch. PoE Power Injector (optional) Non-PoE Switch EN - 6

English 5 Assigning an IP Address 1. Install "Installation Wizard 2" from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment.

The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After searching, the main installer window will pop up.

Network Camera Model No: IP8162P RoHS MAC:0002D1730202 00-02-D1-73-02-02 192.168.5.151 IP8162 This device complies with part 15 of the FCC rules.

8 English 5 Assigning an IP Address 1. Install "Installation Wizard 2" from the Software Utility directory on the software CD. 2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the "Next" button to continue the program. IW2 Installation Wizard 2 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. 4. After searching, the main installer window will pop up. Click on the MAC that matches the one labeled on the bottom of your device to connect to the Network Camera via Internet Explorer. Network Camera Model No: IP8162P RoHS MAC:0002D D IP8162 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Pat. 6,930,709 Made in Taiwan 0002D EN - 7

6 Ready to Use 1. Access the Network Camera from the LAN. 2. Retrieve live video through a web browser or recording software. 3. Unscrew the zoom controller to adjust the zoom factor.

9 6 Ready to Use 1. Access the Network Camera from the LAN. 2. Retrieve live video through a web browser or recording software. 3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten the zoom controller. 4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten the focus controller. N T 3 4 W For further setup, please refer to the user s manual on the software CD. EN - 8

10 English 7 Fine-tune the CS-Mount 1. Detach the CS-mount lens from the camera body. 2. Turn the right side of the camera body up. 3. Use the supplied L-type hex key wrench to loosen the lens mounting screw; the CS-mount ring becomes rotatable. 4. Use a coin to turn the CS-mount ring; fine-tune the distance between the sensor and the lens. 5. When finished, tighten the lens mounting screw to fix the CS-mount ring. 6. Attach the CS-mount lens back to the camera body. Lens mounting screw CS-mounting ring EN - 9

11 0.5 NOTE When choosing the lens for your IP8162/62P, please notice the specifications as below. 1. Flange back length (distance A-B) must be longer than 12.5mm. If the flange back length is too short, the bottom of screw mount may hit the ICR, or result in out of focus when adjusting the focus controller. 2. The screw mount (distance A-C) must be shorter than 4.5mm; in case that the bottom of screw mount may hit the ICR. 3. The distance between the edge of lens (A) and front panel (D) must NOT be longer than 0.5mm; or, it may hit the front panel when adjusting the focus controller, or result in out of focus. 1 A ICR B 2 3 A C A (lens edge) D (front panel) EN - 10

Quick Installation Guide. English Français Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska

Quick Installation Guide. English Français Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska Quick Installation Guide English Français Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska English Warning Before Installation Power off the Network Camera as soon as smoke or unusual