Supplemental guide on Camera Fabrication
|
|
- Garey Allen
- 5 years ago
- Views:
Transcription
1 Supplemental guide on Camera Fabrication This document describes the steps for fabricating your camera and lighting system. 1 Materials needed Gather all your materials. You will need the small lexan sheet (covered in white plastic), a plastic cup, your camera and cables, a film canister, bus wire (the white solid core wire), 4 LEDs, and a 33 Ohm resistor if you are using a camera needing a 9V supply (not pictured). Figure 1 Materials for Camera 2 Sketch your circuit The black and white camera requires 9V at 100mA. The LEDs require 3V at 25mA. The battery supplies 12V. Figure 2 displays a circuit which drops the voltage to the camera to 9V and puts 4 LEDs in series over 12V.
2 Figure 2 Circuit diagram (with 9V black and white camera) 3 Fabricate the lens To waterproof the camera you need a barrier lens between the water and the camera. This prohibits water from entering the camera and also provides an air gap between the outer and inner lens so the refraction of light through the water does not distort the image. If you want to include your LEDs in your camera assembly (recommended for ease of sealing) drill the appropriate number of holes for each LED in the lens plate with a 7/32 drill, as shown in Figure 3. Cut the lexan into a disc so it fits into a plastic cup. Epoxy will be poured into the cup to seal the system later on. You should make cutouts in the lexan that will facilitate pouring epoxy into the cup. Make the lens sit as far as possible into the cup to conserve the volume of epoxy required, but remember you have to fit cables, LED wires, and your video connector should you choose to keep it attached. Keep the white plastic on the lexan during this process to prevent scratching of the lens.
3 Figure 3 Lens and LED mounting plate inside cup 4 Glue the camera onto the lens Test your camera in a TV and see if it is focused for both far and near viewing. If it needs focus, you can screw the face of the camera in or out. Remove the plastic coating from the back side of the lexan lens. Put two VERY SMALL DROPS OF SUPERGLUE on the outside edge of the camera face and glue it to the center of the lexan lens. You want to use very little super glue, as it spreads out on the camera face. Plug your camera in again and MAKE SURE IT IS STILL FOCUSED. Run a small bead of super glue around the edge of the camera face and around the threads of the camera to seal it and lock it into a focused position. This superglue will prevent epoxy from getting into the lens. Cut a ring off the open end of a film canister about ¼ high. Remove the remaining white plastic from the other side of the lens and glue on the rounded edge of the film canister ring, centered on the camera. This ring will prohibit epoxy from getting on the lens when the assembly is cast. Your final assembly should look like Figure 4.
4 Figure 4 Camera and film canister ring glued to lens 5 Glue the LEDs to the lens Put an LED in each LED hole and put a small bead of super glue around the backside edge of the LED, as shown in Figure 5. Be careful to not smudge super glue on the face of the LED, as it will make the light blurry. Remember also to orient your LEDs such that you can connect the positive terminal (long leg) to the negative terminal of the next LED.
5 Figure 5 LEDs glued into lens 6 Solder connections of all the wires Solder together your LEDs, positive terminal of one to the negative of the other. Remember to leave the first positive and the last negative terminal unconnected. Solder two pieces of bus wire to the remaining LED terminals so they can reach the power connector. Cut off the power connector on both the camera and the long cable video/power cable. Remember WHEN YOU CUT OFF THE CONNECTORS, LEAVE AS MUCH WIRE AS POSSIBLE SO IT CAN BE STRIPPED AND SOLDERED. Put the resistor in series with the camera circuit and hook the LEDs up in parallel with the power coming in, as shown in the circuit diagram in Figure 1. You can choose to also cut off the video connector if you want to save room in the cup. When everything is all set you can wrap it in electrical to make a tight package. When everything is packaged verify it works by hooking it up to the 12V battery and the video connector on a TV. The wiring and packaging are shown in Figure 6.
6 Figure 6 wiring and packaging of camera and LED circuits (not shown with resistor) 7 Glue the lens into the cup Glue the lens into the cup by putting a small bead of superglue around the edge where the lens meets the cup. Make sure the lens is LEVEL, as you don t want it to be cockeyed. Leave the wires coming out of the face of the camera lens, as shown in Figure 7. Figure 7 Camera lens glued into cup
7 8 Put screws into the cup When you mount your camera to your robot, you will need to screw it to PVC. You can cast screw threads right into the epoxy by putting screws into the cup in which you will mold the camera, as shown in Figure 8. Put screws wherever you think you many want to mount it, such as on the sides and the back. KEEP YOUR SCREWS AWAY FROM THE WIRES. You don t want water to leak around the screw threads and touch the wires. Figure 8 Screws in cup to cast in screw threads 9 Cast the camera in epoxy Before you cast the camera, hook it up to power and video one last time. It is better to find out now it doesn t work, as it can t be repaired once cast in epoxy. Mix the 2-part urethane epoxy and pour it in through on of the holes in the lens. Fill the up all the way up past the base of the LEDs. Be very careful to not cover the LEDs too far. If you have a lot of room in your cup, you can conserve epoxy by taking up the volume with foam.
8 Figure 9 Camera cast in urethane epoxy (with camera and LEDs turned on)
BuffaloLabs WiFi Lantern Assembly guide version 1
BuffaloLabs WiFi Lantern Assembly guide version 1 Needed equipment: Solder iron Solder wire Cutter Wire stripper (optional) Hot glue gun Overview of the components (not including USB cable and box panels)
More informationMC-1 OPERATION MANUAL MINI CAMERA JW FISHERS MFG INC 1953 COUNTY ST. E. TAUNTON, MA USA
MC-1 MINI CAMERA OPERATION MANUAL JW FISHERS MFG INC 1953 COUNTY ST. E. TAUNTON, MA 02718 USA (508) 822-7330; (800) 822-4744; FAX (508) 880-8949 Email: info@jwfishers.com WEB: www.jwfishers.com SPECIFICATIONS
More informationParts List: Part # Tools List: Instructions:
Parts List: Part # 1 pair of Dayton Audio B652s 300-652 1 Dayton Audio DTA-2 amplifier 300-385 1 MP3 module 320-350 1 7805 +5 VDC voltage regulator 7805 1 12 VDC 2A power supply 129-077 1 2.1 mm panel
More informationSingle cable kit for the FCB1010
Single cable kit for the FCB1010 1. What is it? With this kit, you can turn your FCB1010 into a phantom powered floorboard, which can do 2-way MIDI communication over one single cable. After installing
More informationipad Mini Wi-Fi Front Facing Camera Replacement
ipad Mini Wi-Fi Front Facing Camera Replacement Replace the Front Facing Camera in your ipad Mini Wi-Fi. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 42 INTRODUCTION
More informationButton Code Kit. Assembly Instructions and User Guide. Single Button Code Entry System
Button Code Kit Single Button Code Entry System Assembly Instructions and User Guide Rev 1.0 December 2009 www.alan-parekh.com Copyright 2009 Alan Electronic Projects Inc. 1. Introduction... 4 1.1 Concept
More informationQ2 XBee Handheld Controller Assembly Guide
Q2 XBee Handheld Controller Assembly Guide Copyright Quantum Robotics Inc. Q2 Controller V1.0 1 Parts List: The kit comes with 14 individual bags. 1. Case Top and Bottom 2. Case Screw Package containing:
More informationConstructing a Newtonian Achromatic Refracting Telescope Dr. Larry Browning, SDSU Physics Department
Constructing a Newtonian Achromatic Refracting Telescope Dr. Larry Browning, SDSU Physics Department These are plans to construct a Newtonian achromatic refractor telescope with a 70-mm aperture and an
More informationCanon EOS Rebel T2i Top Cover Replacement
Canon EOS Rebel T2i Top Cover Replacement Replacing the top piece of a Canon T2i (550D). In my case, I had a broken hot-shoe, but as most controls on this camera are built into the same part, this repair
More informationCINTENNA ANTENNA REPAIR GUIDE
The Cintenna is a great tool when looking to transmit WIRELESS DMX data over obstacles or hard to reach places. Wireless DMX can have its issues when not having a good line of sight between the transmitter
More informationGospeed.Racer Hub Assembly for the Asus EEEpc
Gospeed.Racer Hub Assembly for the Asus EEEpc Before you begin: Please understand that these harnesses are all tested one at a time before I ship them. By installing this harness, you agree to assume any
More informationElecraft W1 SWR/Wattmeter Enclosure by W8FGU
Elecraft W1 SWR/Wattmeter Enclosure by W8FGU The W1 enclosure is made of Lexan, a polycarbonate, which is very strong. It also has a UV blocking coating on one side and was assembled carefully with this
More informationSpalding AllSky Camera Assembly Instructions
Spalding AllSky Camera Assembly Instructions www.goskysentinel.com SkySentinel, LLC (SSL) 958 Shaw Circle Melbourne, FL 32940 (321) 405-2477 admin@goskysentinel.com Version: 2.0 Table of Contents List
More informationHow to hardwire the Sony DSC-W35 Digital Camera
How to hardwire the Sony DSC-W35 Digital Camera Copyright, PixController http://www.pixcontroller.com, all rights reserved. Rev. A 3/20/07 This document covers in detail how to modify the Sony DSC-W35
More informationInstalling Sentor. Hardware Installation
Remote base site monitoring and control Installing Sentor Hardware Installation Copyright 2000 Sentor Monitoring Systems Pty Ltd Contents: 1 Introduction... 1 2 Sentor GUI... 2 3 ST3000 Controller... 3
More informationOnwards and Upwards, Your near space guide Overview of the NearSys Two Sensor Temperature Array Figure 1. A complete Two Sensor Temperature Array
The NearSys Two Sensor Temperature Array is a kit that permits a BalloonSat to measure two separate temperatures. When plugged into a flight computer like the BalloonSat Mini, the flight computer provides
More informationFigure 1. A complete Temperature Sensor
The NearSys Temperature Sensor is a kit that permits a BalloonSat to measure the temperature of the air, interior, or object the sensor itself is placed in contact with. When plugged into a flight computer
More informationWii Nunchuk Transceiver. Wiring Diagrams
Wii Nunchuk Transceiver Wiring Diagrams Wii Nunchuk Controller Wiring SCL SCL SDA +3v3 +3v3 Det SDA To Nunchuk Controller Top View Bottom View Bottom View 2.4GHz Wireless Transceiver CMD RXD TXD VCC 220Ω
More informationMCH WIRE HARNESS WITH QUICK DISCONNECT REPLACEMENT Initial Release 1/31/2013
1. Table of Contents 1. Table of Contents Page 1 2. Remove Failed MCH-103.2 Page 1 3. Install MCH-103.2 to MCH-102NW Page 2 4. Install NC3FX-HD to MCH-103.2 Page 3 5. Install MCH-103.2 Battery Terminal
More informationAdventure Time Coffee Cup Lamp with MakeCode
Adventure Time Coffee Cup Lamp with MakeCode Created by Ruiz Brothers Last updated on 2019-01-08 03:18:49 AM UTC Guide Contents Guide Contents Overview Prerequisite Guides Circuit Playground Express 3
More informationDP2 DOOR PHONE. For Technical Assistance Please Phone: (07)
DP2 DOOR PHONE For Technical Assistance Please Phone: (07) 5596 5128 TABLE OF CONTENTS Description Page 3 Door Phone Dimensions Page 4 Door Phone Range Page 5 Door Phone Performance Page 6 Operation Summary
More informationThe Radio Control Temperature Logger (RCTL) Manual For hardware version 1.0 Manual version 1.0b
The Radio Control Temperature Logger (RCTL) Manual For hardware version 1.0 Manual version 1.0b All materials owned by Dan Gebhardt Introduction This device records the temperature of a model engine during
More information7" Touch Screen Display
7" Touch Screen Display Installation Guide Contents Minimum Requirements...1 Select a Location...1 Initial Setup...2 Unboxing...2 Installation...3 Prepare the Panel...3 Install the Mounting Plate...3 Mount
More informationCONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS
CONSOLE CONNECTOR KIT 9501 INSTALLATION INSTRUCTIONS FOR USE WITH: HAMMOND Organ Models L-100, M-100 Series, M-l, M-2, M-3 LESLIE Speaker Models 760, 770, 825 KIT CONTENT Console Connector Assembly 043075
More informationAssembly of the TACOS WAT-910BD Housing v2
1) Circuit Diagram 2) Assembly of PCB a)tools Required. Only simple hand tools are necessary to complete the assembly of the PCB. - Soldering Iron and solder - Needle nose pliers - Wire clippers/trimmers
More informationIt is very important that you read the entire presentation before you start, common mistakes are highlighted at the end. By Jim McDonnell 6/15
It is very important that you read the entire presentation before you start, common mistakes are highlighted at the end. By Jim McDonnell 6/15 1 More Art than Science Over the years MATE has developed
More informationGo-Baby-Go Senior Capstone Project
Go-Baby-Go Senior Capstone Project Assembly Manual Team 22C Alwaleed Alhamra Asrar Alkhabbaz Fawaz Almutairi Sultan Almutairi Eric Trieu Project Sponsor: W.L. Gore & Associates Faculty Advisor: Dr. David
More informationPSM-2 POWER SUPPLY MODULE INSTRUCTIONS
PSM2-09.doc 1 Rev: 8-28-01 PSM-2 POWER SUPPLY MODULE INSTRUCTIONS PSM Model 2 equipped with Field Programmable Output Voltages MODEL PRODUCT OFFERING / VARIATIONS: PSM-2 Metal case housed surface mountable
More informationNov. 07, 2013 p. 5 - changed the B axis unit value to from Changed by Randy per Frank s request.
Correction notes Nov. 07, 2013 p. 5 - changed the B axis unit value to 45.1389 from 40.0000. Changed by Randy per Frank s request. Jan. 22, 2018 p. 5 - changed the B axis unit value and corresponding picture
More informationSolder the Harlequin, Revision F, March Solder the Harlequin - please read carefully (also the addendum!) before starting
Solder the Harlequin, Revision F, March 2014 Page 1 of 8 Solder the Harlequin - please read carefully (also the addendum!) before starting You should check the kit for completeness (see addendum). If you
More informationBuilding the VMW Time Circuitry Meter by Vincent M. Weaver 6 May 2014
Building the VMW Time Circuitry Meter http://www.deater.net/weave/vmwprod/hardware/time_circuit/ by Vincent M. Weaver 6 May 2014 1 Introduction This is a work in progress. I will update it as I complete
More informationHOW TO CHANGE O-S250 mirror motor on PENTAX MZ50
HOW TO CHANGE OS250 mirror motor on PENTAX MZ50 You will need 4 basic but necessary tools : little screwdriver Philips 000 a soldering iron (20W max) + unsolder pump : be cautious with flexible boards,
More informationMailbox Notification Service. Created by Adam Kohring
Mailbox Notification Service Created by Adam Kohring Last updated on 2015-06-24 10:20:07 PM EDT Guide Contents Guide Contents Overview Parts List Adafruit Products Additional Products Print the Circuit
More informationGadget Freak Case #238: Controller Adjusts Garage Lights Build Instructions
Gadget Freak Case #238: Controller Adjusts Garage Lights Build Instructions The schematic diagram shows the main garage-light switch (SW1) that turns on both fluorescent lamps, Lamp 1 and Lamp 2. Only
More information2M IR Mini Dome Quick Installation Guide
1 2M IR Mini Dome Quick Installation Guide Please follow the installation steps below to set up 2M IR Mini Dome IP Camera. Check the package contents against the list below. See P.1 Physical overview.
More informationSeeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox
Seeburg JCU-DEC Kit Convert Your Seeburg DEC Wallbox Into a Jukebox MP3 Compact Flash Player Coin Operated or Free Play Integrated Power Amplifier Line-Out to External Amplifier Programmable Autoplay IR
More informationOnwards and Upwards, Your near space guide. Figure 1. CheapBot Line Follower
The CheapBot Line Follower is a plug-in single-board sensor for almost any programmable robot brain. With it, a robot can detect the presence of a black or white zone beneath its two sensors. In its simplest
More informationEQ573 Assembly guide. EQ573 Assembly guide Main board 1. Diodes. 2. Resistors (1) 3. Test pins. 4. Ceramic capacitors.
EQ573 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationDP4 DOOR PHONE. For Technical Assistance Please Phone: (07)
DP4 DOOR PHONE For Technical Assistance Please Phone: (07) 5596 5128 TABLE OF CONTENTS Description Page 3 Door Phone Dimensions Page 4 Description Continued Page 5 Door Phone Range Page 6 Door Phone Performance
More informationHeathkit HR-1680 PC Card Extender. Heathkit HR-1680 PC Assembly Extender Assembly
Heathkit HR-1680 PC Assembly Extender Assembly Version Date Author Comment 1.0 August 15, 2009 RM Groh Original draft Table of Contents Introduction...1 Heathkit s Approach...2 Parts Required...3 Assembly
More informationWritten By: Kaitlyn Fisher
Motorola Moto Z Play Battery Replacement How to replace a failing Motorola Moto Z Play battery. Written By: Kaitlyn Fisher ifixit CC BY-NC-SA www.ifixit.com Page 1 of 24 INTRODUCTION If the battery on
More informationUpgrading the Mark5 motherboard to the SE7520BD2 Server Board
Upgrading the Mark5 motherboard to the SE7520BD2 Server Board Joint Institute for VLBI in Europe Martin Leeuwinga (leeuwinga@jive.nl) February 2008 1. Introduction This document describes how to upgrade
More information[Note: Power adapter is not included in the kits. Users need to prepare a 9 12 V ( >300mA capacity ) DC power supply]
062 LCD Oscilloscope Assembly Notes Applicable Models: 06203KP, 06204KP DN062-18v02 Important Notes 1. Some components shown in the schematic and PCB layout are for options or adjustments. They do not
More informationPlasma Panel Replacement Guide DU-42PX12X
Plasma Panel Replacement Guide DU-42PX12X Panel Replacement: At this point, the panel has been determined to be defective and replacement is necessary. Upon receiving the replacement panel, it must be
More informationConnecting LEDs to the ADB I/O
Application Note AN-2 By Magnus Pettersson September 26 1996 Connecting LEDs to the I/O Introduction The following notes are for those of you who are a bit inexperienced with hardware components. This
More informationBLUETOOTH AMPLIFIER KIT
PRODUCT INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS CREATE YOUR OWN WIRELESS SPEAKER WITH THIS BLUETOOTH AMPLIFIER KIT Version 1.2 Index of Sheets
More informationManual Version March 2007
Manual Version 1.1 - March 2007 Page 1 Table of Contents Section1: 6922 Line Board Build... 3 6922 Line Board Version Notes... 5 6922 Line Board Build - HARD-WIRED VERSION... 5 Final Connections and Checks
More informationFitting An Emulator into the Yamaha AR Organ
Fitting An Emulator into the Yamaha AR Organ As performed by Les White and Frank Kemplay May 2011 On the upper rear panel remove the top line of 3 screws to allow removal of the top board assemblywhich
More informationHTC RE Companion Handheld camera
HTC RE Companion Handheld camera disassemby HTC RE Companion camera disassembly starting point. This will get the camera open with minimal damage, and give you some options to repair. Written By: Mike
More informationrevolution How does the ibutton work? Full kit including PCB, PICAXE-08M chip and ibutton key. Spare ibutton Key
AXE109S LOG020 Full kit including PCB, PICAXE-08M chip and ibutton key. Spare ibutton Key The ibutton is an electronic chip armoured in a 16mm stainless steel can. Because of this unique, durable package,
More informationAssembling of the CD-Player CD-Two MKII Part 1: PCB s and interconnections
Assembling of the CD-Player CD-Two MKII Part 1: PCB s and interconnections 1. Please check if you have all parts: Overview of mechanical parts: bottom panel with drilling s Outer bottom panel made of Acrylic
More informationHow to build an Olympus D-360L Trail Camera using the PixController Universal "Digital Trail Camera Kit" w/ RS-232-U PIC Chip
Copyright, PixController, Inc. http://www.pixcontroller.com, all rights reserved. How to build an Olympus D-360L Trail Camera using the PixController Universal "Digital Trail Camera Kit" w/ RS-232-U PIC
More informationSharpSky Focuser Construction. SharpSky Focuser. Construction Document V st December 2012 Dave Trewren 1
SharpSky Focuser Construction Document V0.12 1st December 2012 Dave Trewren 1 Contents 1 General... 3 1.1 Change Record... 3 1.2 References... 3 2 Introduction... 5 3 SharpSky driver installation... 5
More informationRS-FS-N01 Wind speed transmitter user's Guide (485type)
RS-FS-N01 Wind speed transmitter user's Guide (485type) Issue: V1.0 1 2 Context 1. Introduction... 4 2. Installation instructions...5 3. Configure the software installation and use... 6 4. Communication
More informationComplete Installation manual
VapoChill TM CPU Cooling System - LightSpeed [AC] TM asetek Inc. Complete Installation manual Date Version Comments 01-04-2004 1.0 1 Installing the VapoChill LightSpeed [AC] TM Preparing the case Step
More informationSchematic Diagram: R2,R3,R4,R7 are ¼ Watt; R5,R6 are 220 Ohm ½ Watt (or two 470 Ohm ¼ Watt in parallel)
Nano DDS VFO Rev_2 Assembly Manual Farrukh Zia, K2ZIA, 2016_0130 Featured in ARRL QST March 2016 Issue Nano DDS VFO is a modification of the original VFO design in Arduino Projects for Amateur Radio by
More informationHome Automation, Inc. Model 32A00-1. OmniTouch Touchscreen
Home Automation, Inc. Model 32A00-1 OmniTouch Touchscreen Installation Manual Document Number 32I00-1 Rev A July, 2003 FCC NOTICE This device complies with FCC Rules Part 15. Operation is subject to the
More informationWritten By: Sam Lionheart
ipad Mini 2 Wi-Fi GPS Antenna Replacement Remove the GPS antenna in an ipad Mini 2 Wi-Fi. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 36 INTRODUCTION Use this guide to replace
More informationFE8171V. 3MP 360 Panoramic View Vandal-proof
FE8171V 3MP 360 Panoramic View Vandal-proof Warning Before Installation English Power off the Network Camera as soon as smoke or unusual odors are detected. Refer to your user's manual for the operating
More informationOutdoor PTZ. Mounting on the Ceiling Using Pendant Mount. Installation Guide. For Models: I93, I94, I95, I96, KCM /12/03
Outdoor PTZ Mounting on the Ceiling Using Pendant Mount For Models: I93, I94, I95, I96, KCM-8211 2013/12/03 Table of Contents Mounting Solutions... 3 Straight Tube Installation Procedures... 4 Step 1:
More informationWritten By: Andrew Optimus Goldberg
ipad Air LTE SIM Board Replacement Replace the SIM board (a.k.a. SIM card bay) on an ipad Air LTE. Written By: Andrew Optimus Goldberg ifixit CC BY-NC-SA www.ifixit.com Page 1 of 32 INTRODUCTION Use this
More informationK2 RIT-SPLIT LED Indicator Mod dated 18 October 2003 Circuit Design by: Wayne Burdick, N6KR Implementation by: Tom Hammond, NØSS
K2 RIT-SPLIT LED Indicator Mod dated 18 October 2003 Circuit Design by: Wayne Burdick, N6KR Implementation by: Tom Hammond, NØSS Show & Tell Pictorial Supplement to the K2 RIT-SPLIT LED Mod Documentation
More informationReflowing Xbox 360 Motherboard
Reflowing Xbox 360 Motherboard Reflow the solder on your Xbox 360's motherboard. Written By: Andrew Bookholt ifixit CC BY-NC-SA www.ifixit.com Page 1 of 31 INTRODUCTION Use this guide to reflow the solder
More informationRainbowduino Word Clock. By Russ Hughes
Rainbowduino Word Clock By Russ Hughes (russ@owt.com) OVERVIEW This word clock is based on the NeoMatrix 8x8 Word Clock by Andy Doro from https://learn.adafruit.com/neomatrix-8x8-word-clock. Not having
More informationROTOPOD PERISCOPE LIGHTING KIT
ROTOPOD PERISCOPE LIGHTING KIT (for ULTIMATE Periscopes) 14-MAR-2013_rev 2.0 I designed the Periscope Lighting Kit to be as flexible as possible. Every LED is individually controllable. I have provided
More informationVPC-64/ VPX-64 VIDEO POLE CAMERA OPERATION MANUAL
VPC-64/ VPX-64 VIDEO POLE CAMERA OPERATION MANUAL RESEARCH ELECTRONICS INTERNATIONAL 455 Security Drive Algood, TN 38506 U.S.A. +1 931-537-6032 http://www.reiusa.net/ COPYRIGHT RESEARCH ELECTRONICS INTERNATIONAL
More informationInstallation/assembly manual for DCC/Power shield
Installation/assembly manual for DCC/Power shield The DCC circuit consists of the following components: R1/R6 R2/R3 R4/R5 D1 C2 2 kω resistor ½ Watt (colour code Red/Black/Black/Brown/Brown) 10 kω resistor
More informationView Wall Interface. Dynamic Glass INSTALLATION GUIDE. Description. System Requirements. Installation Overview
Description The solution is a compact, wall-mounted interface used for monitoring and changing the tint levels of View Dynamic Glass. The product leverages 802.11-based Wi-Fi technology for connectivity
More informationDP2. Door Phone. For Technical Assistance call the Manufacturers direct ph AM - 5PM West Coast Pacific Time
DP2 Door Phone For Technical Assistance call the Manufacturers direct ph 0800 530 8645 9AM - 5PM West Coast Pacific Time NATCOMM USA LLC Supplier Code : NC TABLE OF CONTENTS Description Page 3 Door Phone
More informationInsert the male, 90 angled, 2x10 connectors into the corresponding 2x10 sockets and put them in place, flat under the PCB. Solder.
MC624 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge about
More informationContents Copyright 2013 By Small Bear Electronics LLC
The last piece of pre-assembly before you put everything together is creating the connector for the stomp switch and soldering those components together. Find the six-position Molex connector and the terminated
More informationAlesis MMT8 16x Memory Expansion Modification (all grey model MMT8 s)
Alesis MMT8 16x Memory Expansion Modification (all grey model MMT8 s) by Graham Meredith, 2006 Revised 13 th January 2009 gmeredith1@yahoo.com.au This modification expands the memory of the Alesis MMT8
More informationPO Box 409 Hanover, MD TEL (410)
ME-50 Expansion Amplifier 1 ME-50 Expansion Amplifier Introduction: The ME-50 is a 2 channel audio amplifier capable of delivering up to 25W RMS per channel. It s compact, waterproof design allows for
More informationWritten By: Sam Lionheart
ipad Air Wi-Fi LCD Replacement Use this guide to replace the LCD screen in your ipad Air. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Replace a damaged or nonfunctioning
More informationTerminals, Lugs, and Fasteners
Terminals, Lugs, and Fasteners East Penn cast terminals are manufactured with 100% recycled lead. Lead is recognized as the premium choice in battery cable terminals because of its maximum current carrying
More informationimac Intel 27" EMC 2639 Hard Drive
imac Intel 27" EMC 2639 Hard Drive Replacement Replace the Hard Drive in your imac Intel 27" EMC 2639. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 26 INTRODUCTION Replacing the
More informationCONEC Industrial Ethernet Circular Sealed RJ45 Connector System consists of a RJ45 Plug Kit, a Receptacle Kit and a Protective Cover Assembly.
Revised Sept-28-2009 Sealed Industrial Ethernet Circular IP67 Cat. 5e RJ45 Connector System Instructions CONEC Industrial Ethernet Circular Sealed RJ45 Connector System consists of a RJ45 Plug Kit, a Kit
More informationWide angle lens mods for Hubsan x4 h1207c
Wide angle lens mods for Hubsan x4 h1207c with HD camera I wanted a wide angle lens for this quad, so got a D-lens (120degree) lens module for 808 Keychain Camera off ebay for about 7. I followed a video
More informationYou need the following components to assemble the Black n Wood Nixie Clock circuit board:
You need the following components to assemble the Black n Wood Nixie Clock circuit board: Quantity Designator Description 1 Battery Battery, CR1220 1 Battery Battery holder 3 Button 1, Button 2, Button
More informationA-100G6 - Basic frame assembly diagram
doepfer System A - 100 Rack system A-100 G A-100G6 - Basic frame assembly diagram Parts: 1 Rail with lip, and with tapped hole strip inserted (with M3 threads). 2 Rail with lip, with three M3 hexagon nuts
More informationPLEASE NOTE: These instructions are intended to be used by a person with average mechanical and electrical skills.
ClassicLEDs is please to present their latest line in Corvette LEDs. This covers the 1975 thru 1979 Corvette. This systems does not include the Corvette... PLEASE NOTE: These instructions are intended
More informationHan PCB termination. Han-Fast Lock PCB adapter for Han DD PCB adapter for Han DDD module
Han termination Contents Page Han-Fast Lock... 20.11 adapter for Han DD... 20.13 adapter for Han DDD module... 20.16 adapter for Han 40 A Axial module... 20.18 adapter for Han E... 20.20 adapter for Han
More informationModel: ACA400 & ACA500 Reverse Camera Installation Manual
Model: ACA400 & ACA500 Reverse Camera Installation Manual ACA400 ACA500 FEATURES: High Resolution: 1/4 CMOS Color Camera Compact Zinc Alloy Die Cast Body Waterproof Housing 150 Degree Wide View Angle Minimum
More informationAssembly Guide. LEDs. With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit.
Assembly Guide With these assembly instructions, you can easily build your own SWT16. All required components are included in this kit. You need the following tools: soldering iron, wire cutter and solder.
More informationArduino Panel Meter Clock. By Russ Hughes
Arduino Panel Meter Clock By Russ Hughes (russ@owt.com) OVERVIEW My father has been a lifelong Ham Radio Operator with a fondness for almost anything with a panel meter. After seeing the Trinket Powered
More informationWritten By: Sam Lionheart
ipad Mini 2 Wi-Fi LCD Replacement Replace the LCD in an ipad Mini 2 Wi-Fi. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com Page 1 of 30 INTRODUCTION Use this guide to open your ipad Mini 2
More informationExperimental Procedure
1 of 14 9/10/2018, 11:38 AM https://www.sciencebuddies.org/science-fair-projects/project-ideas/robotics_p028/robotics/obstacle-avoiding-robot (http://www.sciencebuddies.org/science-fair-projects /project-ideas/robotics_p028/robotics/obstacle-avoiding-robot)
More informationMacBook Core 2 Duo Clutch Cover
MacBook Core 2 Duo Clutch Cover Replacement Replace the clutch cover on your MacBook Core 2 Duo. Written By: Ben Eisenman ifixit CC BY-NC-SA www.ifixit.com Page 1 of 29 INTRODUCTION Replace the curved
More informationIntegrated Battery Control System LBCS Step-by-Step Setup Guide
Integrated Battery Control System LBCS Step-by-Step Setup Guide 1. Components of the System 2. Components of the System 3. LBCS Overview 4. Battery Connections 5. Sense Board Installation 6. Sense Board
More informationMACRO MODCHIP FOR XBOX360 CG2 INSTALLATION INSTRUCTIONS
MACRO MODCHIP FOR XBOX360 CG2 INSTALLATION INSTRUCTIONS List of tools and materials needed: Modchip, flexible LED add-on board, 6 tac switches Microsoft wireless CG2 controller Soldering iron and thin
More information3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions
3 pyro output datalogger altimeter with an ATmega 328 microcontroller Kit assembly instructions Version date Author Comments 1.0 29/05/2013 Boris du Reau Initial version Rocket Type Micro-max Model Mid
More informationMust read this before installation Important instructions about your CISS system Instruction Manual for Canon MP500 MP530 MP800 MP830 MX850 Ip4200,ip4300,ip4500,ip6000,ip6600D,ip6700D and more 1. If your
More informationInstallation instructions DC Protection and Delay unit, Version 1.2 The package should contain: A piece of normal gauge yellow wire for the AC connect
Installation instructions DC Protection and Delay unit, Version 1.2 How does the unit work? Delay: Basically a capacitor is charged via a resistor, when the voltage of the capacitor reach a certain level,
More informationATTENTION: OBSERVE PRECAUTIONS FOR HANDLING ESD-SENSITIVE DEVICES
Hard Drive Removal IMPORTANT NOTE: If you are replacing a PATA hard drive with a SATA hard drive, please see PATA to SATA Hard Drive Conversion. Hard Drive Identification: To determine whether your hard
More informationZC-OH5 TAMPER-RESISTANT INDOOR/OUTDOOR HOUSING INSTRUCTION MANUAL FOR USE WITH GANZ ZC-D5000 SERIES MINIDOME CAMERAS
ZC-OH5 TAMPER-RESISTANT INDOOR/OUTDOOR HOUSING INSTRUCTION MANUAL FOR USE WITH GANZ ZC-D5000 SERIES MINIDOME CAMERAS Please carefully read and observe all instructions and warnings contained in this manual
More informationSony SLT Alpha-65V Flash Capacitor
Sony SLT Alpha-65V Flash Capacitor Replacement How to replace the flash capacitor located on the left side of the camera. Written By: Dima Kyle ifixit CC BY-NC-SA www.ifixit.com Page 1 of 11 INTRODUCTION
More informationCP5176 Assembly guide. Soldering. CP5176 Assembly guide Main PCB PCB split. Document revision 2.1 Last modification : 12/11/17
CP5176 Assembly guide Safety warning The kits are main powered and use potentially lethal voltages. Under no circumstance should someone undertake the realisation of a kit unless he has full knowledge
More informationDigital I/O Module. Impro (DIO) Digital I/O Module INSTALLATION MANUAL
COMPONENT CODES: HMI700-1-0-NN-XX HMI701-1-0-NN-XX Digital I/O Module Impro (DIO) Digital I/O Module Specifications INSTALLATION MANUAL The DIO is a Cluster Expansion Module that works in conjunction with
More informationipad Mini 2 Wi-Fi Front Panel Assembly Replacement
ipad Mini 2 Wi-Fi Front Panel Assembly Replacement Fix a broken ipad Mini 2 screen. Replace the front glass and digitizer on an ipad Mini 2 Wi-Fi. Written By: Sam Lionheart ifixit CC BY-NC-SA www.ifixit.com
More informationMake Kits and Casemods
Make Kits and Casemods This weekend, you ll learn how to make a Minty Boost usb charger and a Daisy mp3 player. After you put these together you can put them into customized cases. I made my charger fit
More information