WiFi Wireless Video Door Phone. User Manual

Transcription

1 WiFi Wireless Video Door Phone User Manual

2 Introduction With Hisilicon Hi3518E hardware platform, this WIFI/IP video intercom doorbell uses H.264 image compression. Its picture transmission data is small and power consumption low. This product is easy and safe to operate. It is applicable under both LAN and 3G/4G network. Unlock is safer with its sole ID number as factory unlock password. Restoring factory setting is not necessary if mobile phone is lost; just make missing devices disconnected by changing admin password. All events that happen can be recorded. Moreover, this item has video message function and all important information will not be missed. Outdoor unit's videos can be remotely downloaded by mobile devices; removing TF card and downloading from other terminals are not necessary. Duplex intercom is used. Without manual setting, network rate is timely monitored to achieve fluent and simple intercom. 120 wide view angle camera with real time motion detection function. You can control your door at any place and in any time. Please note: outdoor camera must be fixed well in rain cover before normal user. Magnet in the rain cover has a magnetic sense with outdoor unit. Product Introduction Product Diagram Product Overview APP(idoorphone) Installation APP Main Interface Diagram Connect Doorbell with Android/iOs Devices Connect Doorbell with Power Supply Pairing Operation Network Setting Add Additional Device to a Door Bell APP Main Interface Function Introduction (Take Android Device as an Example) Main Settings Edit Video Surveillance Activity Mobile Network Settings Installation Operation Content Outdoor Unit Wire Connection 11 Connection with Wireless Chime(optional) Package List FAQ 12 13

3 Product Introduction Product Diagram APP(idoorphone) Installation a. For Android users, please log in Google Play, download and install APP (name: idoorphone); or scan QR code on color box and download APP. b. For iphone users, please log in APP Store, search "idoorphone", download and install APP; or scan QR code on color box and download APP. Android APP Main Interface Diagram idoorphone APP Main Interface on Android Devices edit pairing device name refresh function settings device status surveillance interface Product Overview 1.Pairing: Mobile device auto searches and matches outdoor unit; manual ID and password input is not necessary. Operation is easy and quick. 2.Information safe: When a mobile phone is lost, outdoor unit's admin password can be changed by other APP devices. In this way, missing one will be disconnected. Password verification is needed to door release. As a host, outdoor unit judges whether password input by mobile phone is correct or not; and whether unlock password is from connected Android/IOS device. 3.Activities: All activities (including visit info, tamper alarm, motion detection, visitor message and unlock) can be viewed by APP devices. Outdoor unit's videos can be viewed and downloaded. Everything at door can be monitored at any place and in any time. main interface button activity list photo list(pics taken manually) video list(videos recorded manually) version and exit (no push notification if APP exits) 1 2

4 device name device status Indicator light status illustration: Slowly blink from red to blue: no router connection; Fast blink from red to blue: in pairing or connecting router state; Blue light is on: connected to router; Red light is on: calling ios APP Main Interface function settings device ID Red frame area introduction: when device is online, click red frame area into video surveillance interface. When device is offline, click this area to refresh APP. (Please refer to Android APP interface for other function introduction) Push notification introduction of iphone/ipad: 1. When APP is running and device status online, for any visitor call, mobile has push notification. 2. When APP is running and device status online, double click iphone's "Home" key, drag APP, slide it up and stop APP working. Then push notification of doorbell calls will be sent to iphone. If APP is exited in APP's "About" interface, mobile can't receive any push notification Connect Doorbell with Android/iOs Devices 1. Connect Doorbell with Power Supply a. Correctly connect DC power (red wire is positive and black wire negative). Please refer to power connector in Product Diagram. 2. Pairing Operation Steps for Android mobile: a. make doorbell in pairing status: click doorbell's "pairing" key(please refer to its location in Product Digram) and it alerts "paring". Meanwhile, indicator lamp blinks fast from red to blue. b. Make APP into pairing state: ensure Wifi open on mobile and run APP idoorphone, click "Add Device" (see image 1) on APP. APP will auto search doorbell's hot spot; then doorbell hints "paring success". Meanwhile, "WLAN" setting interface(as image 3) auto appears on APP; and a image frame shows on APP. After this, mobile finishes connection with doorbell's LAN. Pairing status will last for 100 seconds; if pairing fails, doorbell tips "pairing failure". ios devices and some Android devices will not auto connect with doorbell's LAN. So manually linking smart phone to doorbell s hot spot is a must.) (see image 2) Steps for ios mobile: a. Make doorbell in pairing status: click doorbell's "pairing" key (please refer to its location in Product Digram) and it alerts "paring". Meanwhile, indicator lamp blinks fast from red to blue. b. Make APP into pairing state: ensure Wifi open on mobile and manually connect mobile to doorbell's LAN(as image 4 shows). Run APP idoorphone and click "Add Device" (see image 1) on APP. Then doorbell hints "paring success". Device will appear on APP interface. (see image 5) 3. Network Setting When device is online on APP, click "Settings"-"WLAN"-"Scan" (after pairing operation, Android APP will auto switch to this setting; as image 3 shows), select a router and enter password. Touch "done" in upper right corner. Then APP will be auto back to main interface. Unit tips password setting correct". And blue indicator light is on. After this, doorbell s Wifi hotspot will be hidden. 4. Add Additional Device to a Door Bell a. If doorbell is not connected to router: make doorbell into pairing status, link extra mobile's Wifi to doorbell's LAN and click "Add Device" on APP interface (please refer to Pairing operation ). b. After doorbell is connected to router: make doorbell into pairing status; connect mobile's Wifi to router, which must be the one that doorbell is linked to; click Add device" on APP (please refer to "Pairing Operation"). b. Fix rain cover well into waterproof case, and wait for about 35 seconds to finished booting. Indicator blinks slow from red to blue after beep music. Doorbell is in standby status. 3 4

5 Note: one doorbell can add 4 smartphones and one mobile supports connection with max 4 outdoor units. Intercom lasts for 2 minutes and is auto end after 2 minutes. Outdoor unit ringing duration is 30 seconds for each call; then if needed, visitor can leave message after beep. APP Main Interface Function Introduction (Take Android Device as an Example) 1. Main Settings Tap "settings" for each basic function setting(as shown image 6). Click "Done" button after each revision. Please note below settings must be done when device is online. a. User Settings: revise device s admin password. The initial password "admin"(see image 7). image1 image2 image3 image6 image7 b. Motion Settings: enable or disable motion detection function and select sensitivity(see image 8). Normally "High" option is recommended. c. Date&Time: synchronize device's time with mobile time. Click "Done" button after revision(view image 9). image4 image5 image8 image9 5 6

6 d. Unlock Settings: unlock password and unlock duration can be revised here. Click "Done" button after change. "Enable Pairing" button can take the role of clicking outdoor unit's "pairing" key. e. TF Card: check capacity of TF card and reformat it. Outdoor unit max supports 32G memory card. f. Device info: check doorbell software version and manually upgrade latest version. In "device info", ios APP has additional "Reset Push". Click this button after each software upgrade to ensure push notification workable. 2. Edit Device can be deleted(image 10), name revised(image 11) and admin password input (see image 12). Note: admin password can only be revised on "User Setting". 4. Activity Click Activity and all activities can be previewed (included call, tamper alarm, motion detection, visitor messages and unlock). Photos/videos can be directly browsed and videos be downloaded(view image 14). back download video view photo image14 settings play video online image10 image11 image12 3. Video Surveillance (see image 13) Notes: a. click video surveillance frame into surveillance mode, with sound button turned off by default. b. Turn on sound before unlock and intercom. sound button unlock image13 hang up take photos manually record videos manually All call, tamper alarm, motion detection, visitor messages and unlock will be recorded in Activity list in photo format. Videos of visitor call, messages and tamper alarm are also saved. ios APP: if "1" appears in APP icon's upper right corner on iphone screen, it means there is new activity. Check event details into Activity list; then "1" on icon will disappear. Mobile Network Settings If phone screen is off and into long-time standby status, APP might stop running. Below mobile settings may help: 1. Settings> Permission Manager> Notification Center> idoorphone. Enable "Allow notifications" and "priority display"(view image 15). 2. Settings> Permission Manager> Protected APPS> idoorphone Enable protected (as image 15). 3.Settings>Networked apps> idoorphone Enable Mobile data and WLAN ( as image 16 shows). 7 Max screen resolution adjust 8

7 Installation 安装操作 Operation Installation Guide Outdoor camera should be installed meter above floor and avoided from direct sunshine. image15 Installation Instruction image16 9 a.punch suitable holes on wall, put screw stopper and fix rain cover on the wall with screw; b.connect power cable (hole diameter 16-30mm) as per wire connecting diagram. Make power cable out from wall hole in case of indoor charge; get cable out of rain cover bottom and connect wire for outdoor charge. c. As above image, put outdoor camera from the top into rain cover, then push camera bottom and confirm its top tightly in shield. Fix unit bottom with matching screws and install screw cap. 10

8 Outdoor Unit Wire Connection Connection with Indoor Chime(optional) Wireless Chime(optional) Front Back Indicator volume Hook melody speaker battery container electronic lock Connection Steps 1.Simultaneously press both volume and melody button of indoor chime. Meanwhile, assemble two 1.5V AAA batteries into container. The red indicator will keep blinking fast. 2. Press doorbell's "call" button(ensure doorbell connection with power) and red indicator lamp will blink one time. Connection of chime and doorbell is finished. Negative Unlock Signal electronic lock Installation Attention 1.Avoid sheltering or covering camera's light sensor; 2.Protect camera from direct sunshine; 3.Ensure correct wiring otherwise device can't work normally. Package List 1 outdoor unit, 1 wireless chime(option), 1 user manual, 1 warranty card, 1 quality certificate, 1 DC charger, 1 power cable, 1 install screws package Positive Unlock Signal 11 12

9 FAQ 常见问题 1. Paring failure a. ios devices and some Android devices do not support Wifi auto switch; manually linking mobile to doorbell s Wifi hotspot is necessary(see image 2). Then do pairing again. b. When additional mobiles need pairing to a same outdoor unit, they must be connected with doorbell's LAN or same WLAN that doorbells is linked to. 2. Device status is offline or disconnection. a. Check whether doorbell is connected with router (see if blue indicator is on) and confirm that wifi/3g/4g signal is available on mobile. b. Ensure network speed about 50k/s under intercom. Poor network will cause disconnection and delay. 3. Doorbell status appears"user name or password incorrect. Admin password is revised and need log in with new admin password. 4. No response or notification from smartphone for visitor calls. a. Android devices: check whether the network is available to both doorbell and smartphone; and whether APP is running. b. IOS devices: check whether the network is available to doorbell and smartphone. 5. Frequent alerts from motion detection. Tap"settings" on APP, select "Alarm setting", then choose "High" sensitivity normally. Other sensitivities are for special environment. 6. No push notification for IOS device. a. Click "settings" button on iphone/ipad, click "notification" button and enable "allow notifications" for idoorphone APP. b. After doorbell's software upgrade, resetting push notification is necessary. Detailed steps as below: tap APP s "setting" button, click "device info" and click "reset push"button. It will take about 10 seconds to finish resetting. 13