H3C S1016/1024 Ethernet Switch User Manual

Transcription

1 Hangzhou H3C Technologies Co., Ltd. Manual Version: T2-UM

2 Copyright , Hangzhou H3C Technologies Co., Ltd. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd. Trademarks H3C,, Aolynk,, H 3 Care,, TOP G,, IRF, NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V 2 G, V n G, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd. All other trademarks that may be mentioned in this manual are the property of their respective owners. CE This equipment complies with the following European Directives: 89/336/EEC (electromagnetic compatibility), 73/23/EEC (low voltage). Notice The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied. To obtain the latest information, please access:

3 Technical Support

4 About This Manual Organization This document is organized as follows: Chapter Chapter1 Product Overview Content This chapter describes the appearance and features of this product. Chapter2 Installation Switch This chapter describes the precautions and steps to install this product. Conventions The manual uses the following conventions: I. Symbols Note Convention Caution Description Means reader be careful. Improper operation may cause data loss or damage to equipment. Means a complementary description. Environmental Protection

5 This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed.

6 Table of Contents Table of Contents Chapter 1 Product Overview Introduction Product Specifications Hardware Description Product Appearance LEDs Chapter 2 Switch Installation Installation Preparations Security Tips Installation Environment Electromagnetic Environment Installing the Switch Sticking Feet Connecting Power Cord Examining the Installation i

7 Chapter 1 Product Overview Chapter 1 Product Overview 1.1 Introduction is a management-free product at desktop level. It offers wire-speed Layer 2 switching immediately after the product is powered on without any configuration. The S1016 provides 16 autosensing 10/100Base-TX ports and the S1024 provides 24 autosensing 10/100Base-TX ports. 1.2 Product Specifications Table 1-1 Specifications of S1016/1024 Item Physical dimensions (H W D ) Weight Port Description S1016: mm ( in.) S1024: mm ( in.) S1016: 1.5 kg (3.3 lb) S1024: 2 kg (4.4 lb) S1016: 16 autosensing 10/100Base-TX Ethernet ports S1024: 24 autosensing 10/100Base-TX Ethernet ports 1-1

8 Item Chapter 1 Product Overview Description Port attribute Cable Input voltage Power consumption Operating temperature Storage temperature Operating humidity (noncondensing) Storage humidity (noncondensing) System cooling RJ-45 connector Compliant with IEEE and IEEE 802.3u 10/100 Mbps transmission rate Half duplex, full duplex, and auto-negotiation Auto-MDI/MDI-X 10Base-T: Category-3/-4/-5 twisted pair cable with maximum transmission distance 100 m (328.1 ft.) 100Base-TX: Category-5 twisted pair cable with maximum transmission distance 100 m (328.1 ft.) 100 VAC to 240 VAC, 50/60 Hz S1016: 6 W S1024: 9 W 0 C to 40 C (32 F to 104 F) 10 C to +70 C (14 F to 158 F) 20% to 85% 10% to 90% Air cooling 1-2

9 Chapter 1 Product Overview Table 1-2 Features of S1016/1024 Features Wire-speed Layer 2 switching Switching mode MAC address table Description All ports support wire-speed forwarding. All ports are in the same broadcast domain. Store and forward Address auto-learning and auto-aging (with aging time 300 seconds) Maximum MAC address entries: 8K 1.3 Hardware Description Product Appearance I. Front panel The power LED, port LEDs and 16/24 (S1016/1024) 10/100Base-TX Ethernet ports are arranged in order on the front panel of the S1016/1024, as shown in Figure 1-1 and Figure 1-2 respectively. Figure 1-1 Front view of S

10 Chapter 1 Product Overview Figure 1-2 Front view of S1024 II. Rear panel The S1016 has an AC power socket and a grounding pole on its rear panel as shown below: Figure 1-3 Rear view of S1016 The S1024 has an AC power socket and a grounding pole on its rear panel as shown below: Figure 1-4 Rear view of S

11 Chapter 1 Product Overview LEDs Table 1-3 LEDs of the S1016/1024 LED Status Indication Power Speed Link/Act Green OFF Green OFF Green OFF Blinking green The switch is powered on. The switch is powered off. The port works in 100 Mbps mode. The port works in 10 Mbps mode or no Ethernet link is present. An Ethernet link is present. No Ethernet link is present. Packets are being transmitted and/or received at the port. 1-5

12 Chapter 2 Switch Installation Chapter 2 Switch Installation 2.1 Installation Preparations Security Tips To avoid any device impairment or bodily injury caused by improper use, take the precautions listed below: Before cleaning the switch, please unplug the switch connector first. Do not clean the switch with wet cloth or liquid. Do not place the switch near water or in any damp area. Prevent water or moisture from entering the switch chassis. Keep the switch to operate in clean environment. Dust buildup on the chassis may result in static absorption, shortening the life span of the switch and causing communication failure. S1016/1024 use air cooling approach for they just generate a small amount of heat. Keep the switch in good ventilation condition. Do not place one switch on another. The switch can operate normally under proper voltage input. Make sure that the operating voltage is consistent with that labeled on the switch. Do not open the chassis while the switch is in operation. Do not open the chassis if not necessary, even when the switch is not powered on. 2-1

13 Chapter 2 Switch Installation Caution: There is a seal on one mounting screw of the chassis of the S1000 series. It must remain untouched unless the agent is on the spot to maintain your switch. Please contact your local agent and get permission if you wish to open the chassis. Otherwise, you will have to take the consequences of your incorrect operations Installation Environment The S1016/1024 can be installed in the corridor or inside the room. These issues must be taken into account: There is enough space (more than 10 cm) near the air-intake hole and the ventilation hole of the switch for heat dissipation of the switch chassis. The installation site has a perfect cooling system. The workbench where the S1016/1024 is located is solid enough to hold the S1016/1024and its accessories. The workbench is well grounded Electromagnetic Environment The switch in use may be affected by exterior interference in radiation and conduction way. Therefore, you need to be sure to: Use a monophase three-wire power socket with Protection Earth (PE) as the AC power supply unit is a TN system. Thereby, the filter circuit in the equipment can effectively filter interference from the power supply system. 2-2

14 Chapter 2 Switch Installation Keep the switch far away from high-power radio launchers, radar launchers, and equipment with high-frequency and high-current. Use electromagnetic shielding if necessary. For example, you can use shielded port cable. Travel the port cable indoors. Outdoor cabling is prohibited, so as to prevent the signal port from possible damages that may be caused by overvoltage and overcurrent of lightning strike. 2.2 Installing the Switch Note: During installation, you are recommended to wear an ESD-preventive wrist strip, which can be connected to the grounding screw of the cabinet, to eliminate possible static damage to the switch Sticking Feet Step 1: Remove the paper covering the adhesive end of the feet. Step 2: Stick the adhesive end of the feet to the circular recess on the bottom of the chassis Connecting Power Cord Step 1: Check if the required power supply unit is used. Step 2: Insert one end of the power cord to the input socket of the switch and the other end to the socket of the external power supply. 2-3

15 Chapter 2 Switch Installation Step 3: Check the status of the power LED on the switch. ON means the connection is OK Examining the Installation Check if the cables are correctly connected with the S1016/1024. Check if all port cables travel indoors. 2-4