SR-S\ SR-D\ SL-PM Quick Instruction of WiFi Connection

Transcription

1 SR-S\ SR-D\ SL-PM Quick Instruction of WiFi Connection

2 Table of Contents SR-S Quick Instruction of WiFi Connection SR-D Quick Instruction of WiFi Connection SL-PM Quick Instruction of WiFi Connection SolarRiver-S SolarRiver-D 1 SolarLake-PM

3 SR-S Quick Instruction of WiFi Connection The Procedure of WiFi Setting Step 1: Write down the WiFi SSID of inverter. When the inverter is running, press the function button until the WiFi SN is displaying on the screen. Step 2: Configure and set parameter of WiFi module. Configuration Available Router Refresh Router 1 1. Choose the WiFi SSID: samilpower_10829a 2. Input the default password samil Input the website: 4. Choose router Router 2 Router 3 Router 4 Prepare a laptop with WiFi. Open the wireless network connection. 2

4 BUFFALO-5D8958 Input Router password and click OK. Back KEY Unmask KEY OK Configuration Available Router Refresh Router 1 Router 2 Router 3 Router 4 3 Wait 15 seconds and then repeat 1 to 3. if connection is established, you can see a tick on the right rooter.

5 You can also change the module password. Choose you can see the following screen. Options Network Setting Device Parameter Setting Firmware Upgrade Options Choose Device Parameter Setting and change your password Back Device Name Device Parameter Setting SAMILPOWER 10829A Password samil123 OK 4

6 Options Router Name In Network Setting, you can connect to router manually. Setting Channel AUTO Security AUTO Key Unmask KEY Reset and factory setting: Screen 1 Hold pressing the function key at screen 1 for 15 seconds. When you see the screen 2, the WiFi setting will be reset to factory setting. Screen 2 5

7 SR-D Quick Instruction of WiFi Connection The Procedure of WiFi Setting Ethernet :22:23 Auto-IP/DHCP Step 1: Ethernet connection established before opening SolarPower Browser. Refer to settings when using router:main Menu->Settings->Network->Ethernet. In "Ethernet" interface move the cursor to "Manual-IP", press "OK" twice(one press to confirm). Then it will enter "Manual-IP" interface. Manual-IP Ethernet Current mode: :22:23 Auto-IP/DHCP Manual-IP Manual-IP Current mode: Press OK to confirm Confirm? 6 Manual-IP

8 Manual-IP Press "right" or "left" key to move the cursor to select the figure which need to be modified. Press "up" or "down" key to modify figure(ip Address Subnet Mask , others are 0). Press OK after modifying. LCD will display the setting parameter and press OK again, now setting is over. LCD interface will reboot and then enter to home interface automatically : 26 : 05 IP: SubnetMask: Gateway: DNS: Parameter set for PC: Set IP address as , Set Subnet mask as Open SolarPower Browser: Left/Right : Move Selection Up/Down : Increase/Decrease value Press OK to confirm 7

9 Step 2: Write down the information of router. Double-click name of inverter then enter detail information interface. Set the SSID of router which WIFI is going to be connected to and input the Router password. Then save these information. Network :27:23 Step 3: Reboot the LCD interface automatically and disconnect wire connection. Step 4: Check WIFI information: Ethernet Enter the interface: Main Menu -> Settings -> Network, move the cursor to "WIFI" and press "OK". WIFI Press OK to confirm 8

10 Wifi : 28 : 10 If WIFI has not been set, shown as following figure : 28 : 50 If WIFI has been set, shown as following figure. Link Name: Press ESC to Back Wifi Link Name: BAFFAL0-5D8959 Press ESC to Back 9

11 SL-PM Quick Instruction of WiFi Connection The Procedure of WiFi Setting Step 1: Write down the WiFi SSID of inverter. Ethernet WIFI Message :22: :12:55 Auto-IP/DHCP Reset module Manual-IP Default module SSID:mode: Current AP_IP: SAMILPOWER_10829A Manual-IP Press ESC to return Press OK to confirm 10 You can see the SSID by: Main Menu -> Settings -> Network -> WiFi Message

12 Configuration Available Router Step 2: Configure and set parameter of WiFi module. Refresh Router 1 Prepare a laptop with WiFi. Open the wireless network connection. 1. Choose the WiFi SSID: samilpower_10829a 2. Input the default password samil Input the website: 4. Choose router Router 2 Router 3 Router 4 BUFFALO-5D8958 Input Router password and click OK. Back KEY Unmask KEY OK 11

13 Configuration Available Router Refresh Wait 15 seconds and then repeat 1 to 3. if connection is established, you can see a tick on the right rooter. Router 1 Router 2 Router 3 Router 4 You can also change the module password. Choose you can see the following screen. Options Network Setting Device Parameter Setting Firmware Upgrade 12

14 Options Choose Device Parameter Setting and change your password Back Device Parameter Setting Device Name SAMILPOWER 10829A Password samil123 OK Options Router Name In Network Setting, you can connect to router manually. Setting Channel AUTO Security AUTO Key Unmask KEY 13

15 WIFI Message :12:55 Reset module Default module SSID: AP_IP: SAMILPOWER_10829A Press ESC to return 14 Factory setting: Choose Default module on the screen, the WiFi setting will be reset to factory setting.

16