Network Master Series

Transcription

1 Configuration Guide Network Master Series MT1000A Network Master Pro MU100010A 10G Multirate Module

2 1. MT1000A Network Master Pro Hardware Options (Required) The MT1000A Network Master Pro is composed of the MT1000A Controller Mainframe and MU100010A Test Interface Module supporting all transport test interfaces except the optical transceiver options. MT1000A Controller Mainframe MT1000A Test Interface Module MT1000A MU100010A The following accessories are supplied with the MT1000A. Power line cord Stylus AC Adapter Utilities ROM (including operation manual) Li-ion Battery MT1000A/MU100010A Quick Reference Guide Softbag Carrying Strap Handle Box for Optical Transceiver (ESD Box) 2. Protocol Options (Requires One at Minimum) The software protocol options enable the transport technology supporting each data rate. At least one of the following options is required. The MU100010A-001 option supports Ethernet, OTN, SDH/SONET and PDH/DSn up to 2.7 Gbps. No additional hardware is required to support any option. MT1000A Supported Transport Technologies Ethernet IPv4/IPv6, Y.1564, RFC 2544, BER, Multistreaming, OAM, SyncE, MPLS, MPLS-TP, Stacked VLAN, PBB-TE, Ping/Traceroute, Cable Test OTN *2 Error/Alarm, Error Performance/Delay/APS Test, FEC Test, O.182 Test, OH Edit/Capture, TCM Monitoring/Generation, Tributary Scan SDH/SONET PDH/DSn Test, Bi-directional Monitoring/Mapping, Error/Alarm, Error Performance/Delay/APS Test, Header Monitoring/Generation, Pointer Event Generation, Tributary Scan Fibre Channel Signal Generation/Monitoring, Latency, BER, Line Alarm/Error Monitor CPRI/OBSAI CPRI/OBSAI L1: Level/Bit rate/deviation measurement, Alarm/Error detection, Unframed BER CPRI L2: Link status monitoring, Alarm/Error detection, Framed BER, RTD measurement Pass-through monitoring Dual channel *1 1.5 Mbps to 2.7 Gbps MU100010A-001 (Add MU100010A-020 TCP Throughput) MU100010A-001 (Add MU100010A-062 ODU Flex *4 ) Single channel *1 10 Gbps MU100010A-011 (Add MU100010A-020 TCP Throughput) MU100010A-051 (Add MU100010A-061 ODU Multiplexing *3 ) (Add MU100010A-062 ODU Flex *4 ) Dual channel *1 10 Gbps MU100010A-012 (Add MU100010A-020 TCP Throughput) MU100010A-052 (Add MU100010A-061 ODU Multiplexing *3 ) (Add MU100010A-062 ODU Flex *4 ) MU100010A-001 MU100010A-081 MU100010A-082 MU100010A-002 1G FC, 2G FC, 4G FC MU100010A-071 CPRI from Mbps to Mbps OBSAI from 768 Mbps to 3072 Mbps MU100010A-091 8G FC, 10G FC MU100010A-072 CPRI from Mbps to Mbps OBSAI at 6144 Mbps MU100010A-092 8G FC, 10G FC MU100010A-073 CPRI from Mbps to Mbps OBSAI at 6144 Mbps *1: The channel is not limited by the position of the physical port. The user can freely select the port to be assigned from two physical ports using software. For Dual Channel, the two different physical ports can operate simultaneously in one unit. *2: When using the OTN function, the channel can be used as a client signal mapped to OTN. For example, the MU100010A-051/052 (for Physical port) and the MU100010A-081/082 (for client signal) are required when mapping STM-64/OC-192 to OTU2 (Figure 1). *3: ODU Multiplex connections are supported by the ODU Multiplexing option, offering users flexible network configuration. This option (green line in Figure 1) supports both single and dual channels. *4: The ODU Flex option supports client signals of any speed with a Mapping function based on the ODU Flex Standard used for transmission over OTN networks. This option (purple line in Figure 1) supports both single and dual channels. (at rates above 4G requires dual channel option) Physical Port Client Signal ODTU2.ts GMP ODU/ OPU Flex CPRI Opt. 7/6 CPRI Opt. 5/4 FC-400 FC-800 GFP-F Ethernet OTU2 OTU1 ODU/ OPU2 ODTU12 (PT=20) ODTU12 (PT=21) ODU /OPU1 ODTU01 (PT=20) GMP STM-64/ OC-192 STM-16/ OC-48 FC-200 CPRI Opt. 3 OTU2e/1e OTU2f/1f ODU/OPU 2e/1e ODU/OPU 2f/1f 2 Configuration Guide l MT1000A ODTU 2.1 GMP ODU/OPU0 GMP GFP-T GigE MU100010A-051/052 OTN 10G Single/Dual Channel STM-4/STM-1 GMP /OC-12/OC-3 MU100010A-011/012 Ethernet 10G Single/Dual Channel FC-100 MU100010A-081/082 STM-64 OC-192 Single/Dual Channel MU100010A-091/092 FC 8G 10G Single/Dual Channel CPRI Opt. 2/1 MU100010A-001 Up to 2.7G Dual Channel 10 GigE MU100010A-002 FC 1G 2G 4G Dual Channel MU100010A-061 ODU Multiplexing MU100010A-062 ODU Flex FC-1200 MU100010A-071 CPRI/OBSAI Up to 5G Dual channel MU100010A-072/073 CPRI/OBSAI 6G to 10G Single/Dual channel Figure 1. OTN mapping options

3 3. Example Configurations This is the base configuration for users requiring all interfaces up to 2.7 Gbps and 10 GigE single channel. Note: This configuration supports single-channel 10 GigE operation on either physical port while testing separately at up to 2.7 Gbps on the other port simultaneously. Required Configuration Model/Order No. Name Remarks MT1000A Network Master Pro Mainframe MU100010A 10G Multirate Module 10G Module MU100010A-001 Up to 2.7G Dual Channel 2.7 Gbps Interface Max. (OTU1, ~1 GigE, ~STM-16/OC-48) MU100010A-011 Ethernet 10G Single Channel 10G Ethernet Interface This configuration is for testing from the OTU2 Physical interface to GigE client signals using dual stage multiplexing. Required Configuration Model/Order No. Name Remarks MT1000A Network Master Pro Mainframe MU100010A 10G Multirate Module 10G Module MU100010A-001 Up to 2.7G Dual Channel 1 GigE Payload Client MU100010A-051 OTN 10G Single Channel 10 Gbps OTN Interface MU100010A-061 ODU Multiplexing Dual Stage Multiplexing (OTU2 ODU1 ODU0 1 GigE) This configuration is for testing from the OTU2e/1e Physical interface to 10 GigE client signals simultaneously on two ports. Required Configuration Model/Order No. Name Remarks MT1000A Network Master Pro Mainframe MU100010A 10G Multirate Module 10G Module MU100010A-012 Ethernet 10G Dual Channel 10 GigE Payload Client (Dual Channel) MU100010A-052 OTN 10G Dual Channel 10 Gbps OTN Interface (Dual Channel) This is the maximum configuration for testing all interfaces (includes WLAN and extended warranty). Using this configuration, any two OTN/10 GigE/CPRI/OBSAI/SDH/FC (1G to 10G) channels can be combined at two Physical ports for simultaneous operation. Required Configuration Model/Order No. Name Remarks MT1000A Network Master Pro Mainframe MU100010A 10G Multirate Module 10G Module MU100010A-001 Up to 2.7G Dual Channel 2.7 Gbps Interface Max. (OTU1, ~1 GigE, ~STM-16/OC-48) MU100010A-012 Ethernet 10G Dual Channel 2 10 Gbps Ethernet Interfaces (simultaneous) MU100010A-020 TCP Throughput RFC 6349 testing MU100010A-052 OTN 10G Dual Channel 2 10 Gbps OTN Interfaces (simultaneous) MU100010A-061 ODU Multiplexing Multiplexing between OTN mappings (OTU2 ODU1, or OTU2 ODU1 OTU0) MU100010A-062 ODU Flex Flex Mapping (OTU2 ODUflex) MU100010A-082 STM-64 OC-192 Dual Channel 2 10 Gbps SDH/SONET Interface (simultaneous) MU100010A-071 CPRI/OBSAI Up to 5G Dual Channel 2 CPRI/OBSAI Interfaces (Up to 5G) (simultaneous) MU100010A-073 CPRI/OBSAI 6G to 10G Dual Channel 2 CPRI/OBSAI Interfaces (6G to 10G) (simultaneous) MU100010A-002 FC 1G 2G 4G Dual Channel 2 FC Interfaces (1G to 4G) (simultaneous) MU100010A-092 FC 8G 10G Dual Channel 2 FC Interfaces (8G to 10G) (simultaneous) MT1000A-003 Connectivity for WLAN/Bluetooth Supports remote control over WLAN and file copying over WLAN/Bluetooth This option supports WLAN/Bluetooth. (Available for certified countries and regions including USA, Canada, Japan and all EU countries. Refer to the Anritsu website for the latest information.) MT1000A-ES210 MU100010A-ES210 2 Years Extended Warranty Service 2 Years Extended Warranty Service The Bluetooth mark and logo are registered trademarks of Bluetooth SIG, Inc. Mainframe Warranty Service Extension (1 year (standard) + 1 year = 2 years warranty service) 10G Multirate Module Warranty Service Extension (1 year (standard) + 1 year = 2 years warranty service) Configuration Guide l MT1000A 3

4 4. Other Options (Not Mandatory) The following options can be configured as required. MT1000A-003 WLAN/Bluetooth Support This option supports WLAN/Bluetooth. (Available for certified countries and regions including USA, Canada, Japan and all EU countries. Refer to the Anritsu website for the latest information.) G0325A GPS Option This option is to measure Ethernet Y.1564 End-to-End unidirectional latency and to Synchronize Ethernet transmitters to GPS signal. G0306A Video Inspection Probe To judge quality and find problems on optical fiber and module endface J1667A GPIB-USB Converter Converter for USB interface of MT1000A, connects to GPIB interface of other instruments or a controller PC. Extended Warranty Options The standard repair service warranty is 1 year. These options extend the warranty for both the Mainframe and Test Interface Module. MT1000A-ES210: 2 Years Extended Warranty Service (Standard + 1 year) MU100010A-ES210: 2 Years Extended Warranty Service (Standard + 1 year) MT1000A-ES310: 3 Years Extended Warranty Service (Standard + 2 year) MU100010A-ES310: 3 Years Extended Warranty Service (Standard + 2 year) MT1000A-ES510: 5 Years Extended Warranty Service (Standard + 4 year) MU100010A-ES510: 5 Years Extended Warranty Service (Standard + 4 year) 5. Accessory Parts - Optical Transceivers (for Optical Transmission) Install an optical transceiver supporting the relevant standard into the /+ slot when testing optical interfaces using the MT1000A. The application parts, /+ lineup, and corresponding standards are listed below. Model/ Order No. Name Form Factor 52 Meg STM Meg Ethernet 156 Meg STM Meg CPRI 622 Meg STM Meg OBSAI 1 Gig FC 1.23 Gig CPRI 1.25 Gig Ethernet 1.54 Gig OBSAI 2 Gig FC 2.46 Gig CPRI Gig STM Gig OTU Gig CPRI OBSAI 4 Gig FC 4.92 Gig CPRI 6.14 Gig CPRI OBSAI 8 Gig FC 9.83 Gig CPRI 9.95 Gig STM Gig CPRI 10.3 Gig Ethernet 10.5 Gig FC 10.7 Gig OTU Gig OTU1e Gig OTU2e Gig OTU1f 11.3 Gig OTU2f G0332A 100M FX 1310 nm MM 1310 nm, MM, 2 km G0329A 10G LR 1310 nm nm, SM, 10 km G0315A 10G LR/LW 1310 nm nm, SM, 10 km G0316A 10G ER/EW 1550 nm 40 km nm, SM, 40 km G0318A 10G ZR/ZW 1550 nm 80 km nm, SM, 80 km G0319A Up to 2.7G 1310 nm 15 km 1310 nm, SM, 15 km G0320A Up to 2.7G 1310 nm 40 km 1310 nm, SM, 40 km G0321A Up to 2.7G 1550 nm 80 km 1550 nm, SM, 80 km G0328A 1G/2G/4G FC 850 nm 850 nm, MM, 0.5 km G0322A 1G/2G/4G FC 1310 nm 1310 nm, SM, 10 km G0323A 1G/2G/4G FC 1550 nm 1550 nm, SM, 40 km G0356A 8G FC/10G SR 850 nm nm, MM, 0.3 km 4 Configuration Guide l MT1000A

5 6. Other Accessory Options (Not Mandatory) Model/Order No. Name Model/Order No. Name B0691A Hard Case Optical Attenuator G0324A J1569A Battery Charger Car 12 Vdc Adapter J1583A Optical Attenuator 10 db LC/PC to LC/PC Electrical Cables W3682AE MT1000A/MU100010A Operation Manual (Printed Hard Copy) J1584A RJ45 Cable 3 m Z1821A J1571A J1575A J1579A J1581A Utilities in USB Stick Optical Cables These are single-core optical cables. (There are no paired cables.) Optical Cable SM LC/PC to SC/PC 3 m Optical Cable SM LC/PC to FC/PC 3 m Optical Cable SM LC/PC to LC/PC 3 m Optical Cable MM LC/PC to LC/PC 3 m J1585A J1586A J1588A J1589A J1591A J1597A J1598A RJ48 to Crocodile Clips Cable 3 m RJ48 to Crocodile Clips Cable 20 db ATT 3 m BNC Cable 2.5 m BNC to 1.6/5.6 Cable 2.5 m RJ48 to Two 3-pin Banana Plug Cable 2.5 m RJ48 Balanced PDH Cable Crossed 3 m Bantam Cable 3 m 7. Retrofit Options When retrofitting options to a previously purcahsed MT1000A, options are marked with a model number -3 **. (For example, the retrofit option equivalent to the MU100010A-001 Up to 2.7G Dual Channel option is the MU100010A-301 Up to 2.7G Dual Channel Retrofit option.) When retrofitting an option always specify one of the following media as well as the relevant option. All purchased -3 ** options will be copied as a batch on the corresponding media. Z1849A: DVD-ROM for Retrofit Options Z1850A: USB Stick for Retrofit Options Retrofit options are offered with an installer linked to the MT1000A or MU100010A serial number. Accordingly, when purchasing a retrofit option, notify Anritsu about the serial number of the hardware in which the retrofit will be installed. (For example, when retrofitting the MT1000A-303 WLAN/Bluetooth Connection Option, provide Anritsu with the MT1000A serial number; when retrofitting the MU100010A-301 Up to 2.7G Dual Channel Retrofit Option, provide Anritsu with the MU100010A serial number.) *: The dual channel option must be purchased when upgrading from a single channel option to a dual channel option. (For example, when upgrading a MU100010A unit in which the MU100010A-011 Ethernet 10G Single Channel Option is installed to dual channel, the MU100010A-312 Ethernet 10G Dual Channel Retrofit Option must be purchased.) Consult Anritsu about the price in this case. Configuration Guide l MT1000A 5

6 8. Recommended Item Number Sequence in Purchase Orders The MT1000A can be configured in many ways. Sometimes, different configurations are included in one purchase order sheet. To ensure the right configurations, it is recommended to add the MT1000A as the first line of each configuration on the sheet. Configuration example 1 Five and two instruments with different configurations: Model/Order No. Name Qty. MT1000A *1 Network Master Pro 5 MU100010A 10G Multirate Module 5 MU100010A-001 Up to 2.7G Dual Channel 5 MU100010A-051 OTN 10G Single Channel 5 MU100010A-061 ODU Multiplexing 5 G0315A 10G LR/LW 1310 nm + 5 *2 G0319A Up to 2.7G 1310 nm 15 km 10 MT1000A *1 Network Master Pro 2 MU100010A 10G Multirate Module 2 MU100010A-051 OTN 10G Single Channel 2 G0315A 10G LR/LW 1310 nm + 2 *2 Configuration example 2 Four, three and five instruments with different configurations: Model/Order No. Name Qty. MT1000A *1 Network Master Pro 4 MU100010A 10G Multirate Module 4 MU100010A-012 Ethernet 10G Dual Channel 4 G0315A 10G LR/LW 1310 nm + 8 *2 MT1000A *1 Network Master Pro 3 MU100010A 10G Multirate Module 3 MU100010A-012 Ethernet 10G Dual Channel 3 MU A-073 CPRI/OBSAI 6G to 10G Dual Channel 3 G0329A 10G LR 1310 nm + 6 MT1000A *1 Network Master Pro 5 MU100010A 10G Multirate Module 5 MU100010A-012 Ethernet 10G Dual Channel 5 MU100010A-051 OTN 10G Single Channel 5 G0315A 10G LR/LW 1310 nm + 10 *2 *1: MT1000A is located at the first line of each configuration in the purchase order. *2: If accessories shall not be distributed equally between the instruments, it is recommended to split the configuration to each mainframe. 6 Configuration Guide l MT1000A

7 Note: Configuration Guide l MT1000A 7

8 Catalog No. MT1000A_ConfigGuide-E-A-1-(6.00) Printed in Japan 28/SEP/2015 ddcm/cdt