Huawei Agile Distributed Wi-Fi Solution Datasheet

Transcription

1 Huawei Agile Distributed Wi-Fi Solution Datasheet

2

3 Wi-Fi Solution Datasheet 01 Product Overview... // As ICT construction is taking place in various industries, such as the education, business, and enterprise, Wi-Fi technology has also found a wide application. Traditional settled AP or indoor distributed AP face the problems of poor signals or insufficient performance when providing coverage for dormitories, hotels, or offices. To resolve these problems, Huawei reforms the architecture of the traditional network and launches the innovative agile distributed Wi-Fi solution which can provide Gbit/s high bandwidth for each room and comprehensive coverage without coverage holes. The agile distributed Wi-Fi solution is composed of the central AP (AD9430DN-24 or AD9430DN-12) and remote unit (R240D or R230D). The central AP can be deployed in the equipment room, weak-current well, or on the corridor. The remote units (RUs) are placed in rooms, and signals are transmitted over wired cables, without wall penetration loss, delivering high-quality wireless access services. AD9430DN-24 AD9430DN-12 R240D R230D Feature Overview... // The AD9430DN-24 central AP can be connected to 24 RUs directly and a maximum of 48 RUs through a switch. The AD9430DN-12 central AP can be connected to 12 RUs directly and a maximum of 24 RUs through a switch. The RUs (R240D and R230D) support ac wave 1, 2x2 MIMO, and two spatial streams. They can provide services simultaneously on both 2.4 GHz and frequency bands and support a highest rate of 300 Mbit/s at 2.4 GHz, 867 Mbit/s at, and Gbit/s for the device. The R240D and R230D have built-in antennas and support PoE power supply in compliance with IEEE 802.3af/at, simplifying deployment and cable routing. The R240D and R230D support ceiling mounting, wall mounting, and wall plate mounting. An R240D provides one GE interface and four 100M interfaces for Ethernet connections or wired terminal connections, and one phone interface for phone connections.

4 Wi-Fi Solution Datasheet 02 Typical Networking... // Typical networking of the central AP and RUs Room Room Room Room Corridor Central AP The downlink GE interfaces of the central AP Room Room Room Room Extra-low voltage room (ELV) support PoE power supply and can be directly connected to RUs. This solution is applicable to scenarios with a high density of rooms, such as dormitories, hotels, and offices. Feature Descriptions... // Easy to Manage The RUs do not occupy AC licenses. The AC only needs to manage central APs, so nearly 10,000 rooms require merely about 200 APs. Flexible Deployment Modes Ensure Full Signal Coverage Without Coverage Holes A central AP connects to indoor RUs through network cables without wall penetration loss and feeder loss, implementing highquality signal coverage. The RUs can be flexibly mounted to a wall plate, wall, or ceiling Long-Distance Coverage Unlike the traditional distributed AP which allows for a maximum feeder length of 15 m, the central AP uses network cables to replace feeder cables and supports up to 100 m distance from the RUs. The network coverage range is therefore expanded by several times. Zero Roaming Achieves Smooth Service Switchover Central APs have powerful computing capacity to create a private roaming domain for each user. In this way, user roaming will not trigger reassociation and reauthentication, ensuring zero roaming of users and no packet loss. Link Disconnection Survival When the link between the central AP and AC disconnects, the central AP and RUs can maintain the current working states, preventing service interuptions of users and ensuring high-reliability transmission.

5 Wi-Fi Solution Datasheet 03 Hierarchical Processing Technology, High Wireless Forwarding Capability Huawei agile distributed Wi-Fi solution uses innovative hierarchical processing technology. The central AP manages RUs in a centralized manner and concurrently forwards service traffic, while the RUs only process radio signals. The hierarchical design makes the network structure clearer and reduces the processing burden on the central AP and RUs, improving efficiency and optimizing the overall wireless forwarding performance. Basic Specifications... // Hardware Specifications (Central AP) Item AD9430DN-24 AD9430DN-12 Technical Power Dimensions (H x W x D) 43.6 mm x 442 mm x 312 mm 53 mm x 220 mm x 220 mm Weight 4.4 kg 0.8 kg Power input 100 V AC to 24 V AC 48 V DC or POE Power output 24-port standard PoE output: 380 W (maximum output power) 12-port PoE output: 62.5 W (maximum PoE output power) Operating temperature 0 o C to +45 o C 10 o C to +50 o C Storage temperature 40 o C to +70 o C 40 o C to +70 o C Environmental Operating humidity 5% to 95% (non-condensing) 5% to 95% (non-condensing) Altitude 60 m to m 60 m to m Atmospheric pressure 70 kpa to 106 kpa 70 kpa to 106 kpa

6 Wi-Fi Solution Datasheet 04 Item AD9430DN-24 AD9430DN-12 Forwarding capability 4 Gbit/s 1.2 Gbit/s Interface type 4 x uplink GE combo interfaces 24 x downlink GE electrical interfaces (PoE out) 1 x Console interface (RJ45) 12 x 10/100/1000BASE-T (PoE out) 2 x 10/100/1000BASE-T (one UPoEin port) 1 x Console interface (RJ45) Power module indicator (PWR): indicates Performance LED indicator the power-on status of the device. System running status indicator (SYS): indicates the running status of the device. Service network port indicator: indicates the data transmission status and PoE status of a network port. USB indicator: indicates the data transmission status of the USB flash drive. System indicator: indicates the running status of the device. Service network port indicator: indicates the data transmission status and PoE status of a network port. USB indicator: indicates the data transmission status of the USB flash drive. Maximum number of users Maximum number of associated users: 4096 Maximum number of associated users: 2048 Number of managed RUs Directly connected RUs: 24 RUs connected through a switch: 48 Directly connected RUs: 12 (R230Ds) or 6 (R240Ds) Hybrid access of the R230D and R240D is not supported. RUs connected through a switch: 24 Maximum number of VAPs for each radio

7 Wi-Fi Solution Datasheet 05 Hardware (RU) Item R240D R230D Dimensions (H x W x D) 41.5 mm x 140 mm x 86 mm 26 mm x 120 mm x 86 mm 4 x 10M/100M self-adaptive interface (RJ45) Technical Interfaces 1 x 10M/100M/1000M self-adaptive interface (RJ45) 2 x Telephone interface (RJ11, pass-through) 1 x 10M/100M self-adaptive interface (FE) Mounting mode Wall mounting, ceiling mounting, wall plate mounting Wall mounting, ceiling mounting, wall plate mounting Power Power input PoE power supply in compliance with IEEE 802.3af/at Adapter power supply: 12 V ± 10%, 16 V MAX, 2.1 mm DC JACK PoE power supply in compliance with IEEE 802.3af/at Environmental Operating temperature Storage temperature Operating humidity 0 o C to +40 o C 0 o C to +45 o C 40 o C to +70 o C 40 o C to +70 o C 5% to 95% (non-condensing) 5% to 95% (non-condensing) Altitude 60 m to m 60 m to m Atmospheric pressure 70 kpa to 106 kpa 70 kpa to 106 kpa Standards compliance b/g/n/a/ac b/g/n/a/ac MIMO 2 x 2 2 x 2 Bandwidth Gbit/s Gbit/s Antenna type Built-in antennas (Horizontal beamwidth 360 o ) Built-in antennas (Horizontal beamwidth 360 o ) Radio Antenna gain Maximum number of users 2.4G: 2 dbi 5G: 3 dbi 2.4G: 3 dbi 5G: 4 dbi Maximum transmit power 20 dbm NOTE: The actual transmit power depends on local laws and regulations. 20 dbm NOTE: The actual transmit power depends on local laws and regulations. Power increment 1 dbm 1 dbm

8 Wi-Fi Solution Datasheet 06 Item R240D R230D 2.4 GHz b (CCK): Mb/s; Mb/s 2.4 GHz b (CCK): Mb/s; Mb/s 2.4 GHz g (non-ht20): 95 6 Mb/s; Mb/s 2.4 GHz g (non-ht20): 95 6 Mb/s; Mb/s 2.4 GHz n (HT20): 95 MCS0; 77 MCS7 2.4 GHz n (HT20): 95 MCS0; 77 MCS7 2.4 GHz n (HT40): 93 MCS0; 74 MCS7 2.4 GHz n (HT40): 93 MCS0; -74 MCS7 Radio Receiver sensitivity a (non-ht20): 94 6 Mb/s; Mb/s n (HT20): 94 MCS0; 76 MCS a (non-ht20): 94 6 Mb/s; Mb/s n (HT20): 94 MCS0; 76 MCS n (HT40): 91 MCS0; 73 MCS n (HT40): 91 MCS0; 73 MCS ac (VTH20): 95 MCS0NSS1; 71 MCS8NSS ac (VTH20): 95 MCS0NSS1; 71 MCS8NSS ac (VTH40): 91 MCS0NSS1; 66 MCS9NSS ac (VTH40): 91 MCS0NSS1; 66 MCS9NSS ac (VTH80): 88 MCS0NSS1; 63 MCS9NSS ac (VTH80): 88 MCS0NSS1; 63 MCS9NSS1

9 Wi-Fi Solution Datasheet 07 Software Item WLAN features Network features Description Compliance with IEEE a/b/g/n/ac Maximum rate: Gbit/s Maximum Ratio Combining (MRC) Cyclic Delay Diversity (CDD)/Cyclic Shift Diversity (CSD) Maximum Likelihood Detection (MLD) Data unit aggregation, including A-MPDU (Tx/Rx) and A-MSDU (Rx only) Dynamic Frequency Selection (DFS) Short Guard Interval (GI) in 20 MHz, 40 MHz, and 80 MHz modes Priority mapping and packet scheduling based on a Wi-Fi Multimedia (WMM) profile to implement priority-based data processing and forwarding Automatic and manual rate adjustment (the rate is adjusted automatically by default) WLAN channel management and channel rate adjustment Automatic channel scanning and interference avoidance Service Set Identifier (SSID) hiding, support for SSIDs in Chinese Signal Sustain Technology (SST) Unscheduled Automatic Power Save Delivery (U-APSD) Control and Provisioning of Wireless Access Points (CAPWAP) in Fit AP mode Automatic access Hotspot k and v smart roaming Fast roaming ( 50 ms) Compliance with IEEE 802.3u Auto-negotiation of the rate and duplex mode; automatic switchover between the Media Dependent Interface (MDI) and Media Dependent Interface Crossover (MDI-X) SSID-based VLAN assignment 4,094 VLAN IDs (1 to 4,094) and a maximum of 16 virtual APs (VAPs) for each radio AP control channel in tagged and untagged mixed mode DHCP client, obtaining IP addresses through DHCP Tunnel forwarding and direct forwarding STA isolation in the same VLAN Multicast Domain Name Service (mdns) gateway protocol: supports AirPlay and AirPrint service sharing between users of different VLANs Access control lists (ACLs) Link Layer Discovery Protocol (LLDP) Service holding upon CAPWAP link disconnection Unified authentication on the AC Soft Generic Routing Encapsulation (GRE) IPv6 Portal IPv6 Source Address Validation Improvements (SAVI) IPv4/IPv6 ACL Network Address Translation (NAT)

10 Wi-Fi Solution Datasheet 08 Item QoS features Security features Maintenance features BYOD Locating Service Spectrum analysis Description Priority mapping and packet scheduling based on a WMM profile to implement priority-based data processing and forwarding WMM parameter management for each radio WMM power saving Priority mapping for upstream packets and flow-based mapping for downstream packets Queue mapping and scheduling User-based bandwidth limiting Adaptive bandwidth management (the system dynamically adjusts bandwidth based on the number of users and radio environment to improve user experience) Support for Microsoft Lync APIs and high voice call quality through Lync API identification and scheduling Open system authentication WEP authentication/encryption WPA/WPA2-PSK authentication and encryption WPA/WPA x authentication and encryption WPA-WPA2 authentication WAPI authentication and encryption WIDS including rogue AP and STA detection, attack detection, STA/AP blacklist and whitelist 802.1x authentication, MAC address authentication, and Portal authentication w Protected Management Frames (PMFs) Unified management and maintenance on the AC Plug-and-Play (PnP): automatic ally going online and loading configurations Batch upgrade Local AP management through the serial port or using Telnet Real-time configuration monitoring and fast fault location using the NMS System status alarm STelnet using SSH v2 SFTP using SSH v2 Identifies the device type according to the Organizationally Unique Identifier (OUI) in the MAC address. Identifies the device type according to the User Agent (UA) information in an HTTP packet Identifies the device type according to DHCP options. The RADIUS server delivers packet forwarding, security, and QoS policies according to the device type carried in the RADIUS authentication and accounting packets. Locates tags manufactured by AeroScout or Ekahau. Locates Wi-Fi terminals. Identifies interference sources such as baby monitors, Bluetooth devices, digital cordless phones (at 2.4 GHz frequency band only), wireless audio transmitters (at both the 2.4 GHz and frequency bands), wireless game controllers, and microwave ovens. Works with Huawei esight to locate and perform spectrum analysis on interference sources.

11 Wi-Fi Solution Datasheet 09 Standards compliance Item Description Safety standards Radio standards EMC standards IEEE standards UL IEC EN GB 4943 ETSI EN ETSI EN RSS-210 AS/NZS 4268 EN EN ETSI EN ICES-003 YD/T ITU k.21 GB 9254 GB EN EN CISPR 22 CISPR 24 IEC IEC IEEE a/b/g IEEE n IEEE ac IEEE h IEEE d IEEE e IEEE k IEEE u IEEE v IEEE w

12 Wi-Fi Solution Datasheet 10 Item Security standards Environmental standards EMF RoHS Reach WEEE Description i, Wi-Fi Protected Access 2 (WPA2), WPA 802.1z Advanced Encryption Standards (AES), Temporal Key Integrity Protocol (TKIP), and Extensible Authentication Protocol (EAP) type(s): EAP-Transport Layer Security (TLS) EAP-Tunneled TLS (TTLS) or Microsoft Challenge Handshake Authentication Protocol Version 2 (MSCHAPv2) Protected EAP (PEAP) v0 or EAP-MSCHAPv2 EAP-Flexible Authentication via Secure Tunneling (FAST) PEAP v1 or EAP-Generic Token Card (GTC) EAP-Subscriber Identity Module (SIM) ETSI ETSI ETSI ETSI ETSI ETSI CENELEC EN CENELEC EN RSS-102 Directive 2002/95/EC & 2011/65/EU Regulation 1907/2006/EC Directive 2002/96/EC & 2012/19/EU Ordering Information Component Part Description Configuration Description Remarks Central AP AD9430DN-24 Assembling Components,AD9430DN- 24,AD9430DN-24,AD9430DN-24 Mainframe(4 GE Combo Port,24 GE Port),Additional AC Power Wire 1. The AD9430DN-24 cannot be managed by the native AC until 2016Q1. 2. The C13 AC power cable is mandatory and needs to be selected according to standards of the destination country. The power cable is 3 m long by default and needs to be configured separately. 3. The standard configuration includes 2pcs IEC mounting ears. The standard configuration does not include network cables.

13 Wi-Fi Solution Datasheet 11 Component Part Description Configuration Description Remarks Remote Unit R240D Broadband Network Terminal,R240D,5*RJ45, 2*RJ11,11ac, 2*2 Double Frequency 1. This item does not include any power adapter and PoE power supply is recommended. 2. The standard configuration includes two mounting screws. The network and phone cables are optional and independently purchased by customers. The quantity is determined according to network requirements. 3. The AC6605, AC6005, and ACU2 are recommended for use with the AP, and the native AC is expected to be used with the AP in 2016Q1. The standard configuration does not include network cables. R230D Broadband Network Terminal,R230D,1*RJ45, 11ac, 2*2 Double Frequency 1. This item does not include any power adapter and PoE power supply is recommended. 2. The AC6605, AC6005, and ACU2 are recommended for use with the AP, and the native AC is expected to be used with the AP in 2016Q1. The standard configuration does not include network cables. Power Adapter 220 V to 12 V power adapter AC/DC Adapter--5degC-45degC-90V-270V- 12V/2A-Europe Standard-DC inlet European standard Sold only on markets outside China. 220 V to 12 V power adapter AC/DC Adapter--5degC-45degC-90V-270V- 12V/2A-UK Standard-DC inlet UK standard Sold only on markets outside China. 220 V to 12 V power adapter AC/DC Adapter--5degC-45degC-90V-270V- 12V/2A-Australia Standard-DC inlet Australian standard Sold only on markets outside China. 220 V to 12 V power adapter Adapter--5degC-45degC-90V-270V- 12V/2A-Brazil Standard-DC inlet Brazilian standard Sold only on markets outside China. 220 V to 12 V power adapter Adapter,- 5degC,45degC,90V,270V,12V/2A,US Standard/DC inlet US standard Sold only on markets outside China.

14 Wi-Fi Solution Datasheet 12 Professional Service and Support Huawei WLAN planning tools deliver expert network design and optimization services using the most professional simulation platform in the industry. Backed by fifteen years of continuous investment in wireless technologies, extensive network planning and optimization experience, and rich expert resources, Huawei helps customers: Design, deploy, and operate a high-performance network that is reliable and secure. Maximize return on investment and reduce operating expenses. More Information For more information, please visit or contact your local Huawei office. Enterprise Services Product Overview Marketing Documentation

15

16 Copyright Huawei Technologies Co., Ltd All rights reserved. No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd. Trademark Notice, HUAWEI, and are trademarks or registered trademarks of Huawei Technologies Co., Ltd. Other trademarks, product, service and company names mentioned are the property of their respective owners. General Disclaimer The information in this document may contain predictive statements including, without limitation, statements regarding the future financial and operating results, future product portfolio, new technology, etc. There are a number of factors that could cause actual results and developments to differ materially from those expressed or implied in the predictive statements. Therefore, such information is provided for reference purpose only and constitutes neither an offer nor an acceptance. Huawei may change the information at any time without notice.