Interconnecting networks with switches. Virtual Local Area Networks (VLAN)
|
|
|
- Angela Mills
- 6 years ago
- Views:
Transcription
1 1 Interconnecting networks with switches. Virtual Local Area Networks (VLAN) Experimental Development Exercise 1: Creating VLANs and trunk links using the 802.1Q protocol The aims of this exercise are: 1. Creating a switch-based configuration and testing it; 2. Creating VLANs, naming VLANs, and assigning ports to VLANs; 3. Creating trunk links using the 802.1Q protocol for intra-vlan communications; 4. Testing the functionality of VLANs by testing the connectivity between stations. 1.1 Initial configuration Open Packet Tracer 5.3 and design the following topology: 1.2. Creating VLANs and ports assignation The following set of commands illustrates the configuration for Switch0: Switch>enable Switch#configure terminal Switch(config)#hostname Switch0 Switch0(config)# vlan 2
2 2 Switch0(config-vlan )#name Telecom Switch0(config-vlan )#exit Switch0(config)# vlan 3 Switch0(config-vlan )#name Radiocom Switch0(config-vlan )#CTR^Z Switch0#show vlan brief Switch0#configure terminal Switch0(config)#interface fastethernet 0/4 // selection of the interface (Ethernet port) Switch0(config-if)#switchport mode access //setting the port for the access mode Switch0(config-if)#switchport access vlan 2 //assigning the port to the corresponding VLAN Switch0(config-if)# exit Switch0(config)# interface fa 0/7 Switch0(config-if)#switchport mode access Switch0(config-if)#switchport access vlan 3 Switch0(config-if)#CTRL^Z Switch0#show vlan brief Now, save the configuration: Switch0# write memory *** Configure Switch1 in a similar manner.
3 Creating an 802.1Q trunk For each switch, execute the following operations: enter the configuration mode (using the #configure terminal command) and set to the trunk mode the interface that connects the present switch with the other switch (cross-over link). The following set of commands illustrates the trunk configuration for Switch0: Switch0(configure)#interface fa0/1 Switch0 (config-if) #switchport mode trunk %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,changed state to %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,changed state to up Switch0 (config-if)# CTRL^Z Switch0# show interface trunk *** In a similar manner, configure the corresponding interface from Switch Checking the connectivity Now, you will check the connectivity between stations from the same VLAN using ping. First, set the computers belonging to the same VLAN with the IP addresses from the same network as in the table below. Computer VLAN IP MASK PC0 2 Telecom PC1 2 Telecom PC2 3 Radiocom PC3 3 Radiocom Using ping, check the connectivity between 2 computers belonging to different VLANs, but connected to the same switch. What is the result? Check the connectivity between 2 computers belonging to the same VLAN, but connected to different switches. What is the result? Check the connectivity between 2 computers belonging to different VLANs, but connected to different switches. What is the result?
4 4 Exercise 2: Inter-VLAN routing The aims of this exercise are to create and test an inter-vlan configuration: 1. Starting from the configuration in exercise 1, add new devices (1 router and 1 switch) to allow an inter-vlan communication; 2. Add trunk links between switches; 3. Configure the router interface to encapsulate both VLANs. For this purpose, router subinterfaces are created to set the VLANs encapsulations; 4. Test the functionality of VLANs by testing the connectivity between computers. 2.1 Initial settings Open Packet Tracer 5.3 and design the following topology: 2.2. Configuring the trunk links Switch0(config)#interface fastethernet 0/2 // configure port fa 0/2 as trunk Switch0(config-if)#switchport mode trunk %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2,changed state to %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2,changed state to up Switch1(config)#interface fastethernet 0/2 // configure port fa 0/2 as trunk Switch1(config-if)#switchport mode trunk %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2,changed state to %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2,changed state to up
5 5 Switch>enable Switch#configure terminal Switch(config)#hostname Switch2 Switch2(config)#interface fastethernet 0/2 Switch2(config-if)#switchport mode trunk %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2,changed state to %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/2,changed state to up Switch2(config-if)#interface fastethernet 0/3 Switch2(config-if)#switchport mode trunk %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3,changed state to %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/3,changed state to up Switch2(config)#interface fastethernet 0/1 Switch2(config-if)#switchport mode trunk %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,changed state to %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,changed state to up 2.3. Router configuration Router0>enable Router0#configure terminal Router0(config)#interface fastethernet 0/0 Router0(config-if)#no shut %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,changed state to %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1,changed state to up Router0(config-subif)#interface fastethernet 0/0.2 Router0(config-subif)#encapsulation dot1q 2 // 2 represents the encapsulated VLAN Router0(config-subif)#ip address Router0(config-subif)#interface fastethernet 0/0.3 Router0(config-subif)#encapsulation dot1q 3 Router0(config-subif)#ip address Router0(config-subif)#end Save the router s configuration using the following command: Router0#copy run start Testing the inter-vlan routing The connectivity between the 2 VLANs is tested using ping. In order to check the configuration, you have to set IP addresses for all router sub-interfaces and configure the correct Default Gateway address for each computer. The Default Gateway address must be the IP address of the sub-interface corresponding to the VLAN that the computer is assigned to. The IP addresses of the router s sub-interfaces are given in the table below. Router IP MASK Fa 0/ Fa 0/
6 6 Now, set the computers with the IP addresses as in the table below. Computer VLAN IP MASK Default Gateway PC0 2 Telecom PC1 2 Telecom PC2 3 Radiocom PC3 3 Radiocom Using ping, check the connectivity between 2 computers belonging to different VLANs, but connected to the same switch. What is the result? Check the connectivity between 2 computers belonging to different VLANs, but connected to different switches. What is the result?
Lab 6.4.1: Basic Inter-VLAN Routing
Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 172.17.99.1 S2 VLAN 99 172.17.99.12 255.255.255.0 172.17.99.1
the larger the number of users and devices, the more broadcasts and packets each switch must handle.
VLANs Introduction By default, routers allow broadcasts to occur only within the originating network, while switches forward broadcasts to all segments. Flat network = one broadcast domain. that the largest
Lab Configuring and Testing the Rapid Spanning Tree Prototype
Lab 7.3.3 Configuring and Testing the Rapid Spanning Tree Prototype Device Designation Device Name IP Address Subnet Mask Default Gateway Fa0/0.1 10.0.0.1 255.255.255.0 R1 BR4 Fa0/0.10 10.10.10.254 255.255.255.0
Lab 5: Inter-VLANs Routing
Lab 5: Inter-VLANs Routing Network Topology:- Device Interface IP Address Subnet Mask Gateway/Clock Rate Fa 0/0.10 10.5.0.1 255.255.255.192 ----- R1 Fa 0/0.20 10.6.0.1 255.255.255.192 ----- Fa 0/0.30 10.10.0.1
University of Jordan Faculty of Engineering & Technology Computer Engineering Department Advance Networks Laboratory Exp.4 Inter-VLAN Routing
University of Jordan Faculty of Engineering & Technology Computer Engineering Department Advance Networks Laboratory 0907529 Exp.4 Inter-VLAN Routing Objectives 1. Describe the three primary options for
Lab Configuring Inter-VLAN Routing
Lab 9.3.6 Configuring Inter-VLAN Routing Objective Create a basic switch configuration and verify it. Create multiple VLANs, name them and assign multiple member ports to them. Create a basic configuration
Configuring HSRP. Global Knowledge Training LLC L5-1
L5 Configuring HSRP Global Knowledge Training LLC L5-1 Objectives In this lab you will examine the hot standby router protocol (HSRP). First you will configure PxR2 similar to PxR1, so they are both possible
TELECOMMUNICATION MANAGEMENT AND NETWORKS
QUAID-E-AWAM UNIVERSITY OF ENGINEERING SCIENCE AND TECHNOLOGY, NAWABSHAH TELECOMMUNICATION MANAGEMENT AND NETWORKS LAB # 3 CONFIGURING INTERFACES OF ROUTER AND SWITCH Topology Diagram Addressing Table
Lab Analyzing a Test Plan and Performing a Test
Lab 7.1.6 Analyzing a Test Plan and Performing a Test Objectives Analyze a sample test plan to determine: The subject of the test The methods and tools for testing The potential results Perform the test
International Journal of Scientific & Engineering Research Volume 9, Issue 9, September ISSN
International Journal of Scientific & Engineering Research Volume 9, Issue 9, September-2018 10 The Importance of VLANs and Trunk Links in Network Communication Areas Dlnya Abdulahad Aziz Computer Technical
VLAN Range. Feature Overview
VLAN Range Feature History Release 12.0(7)XE 12.1(5)T 12.2(2)DD 12.2(4)B 12.2(8)T 12.2(13)T Modification The interface range command was introduced. The interface range command was integrated into Cisco
CCNP SWITCH Portable Command Guide Scott Empson Hans Roth Warning and Disclaimer Trademark Acknowledgments
ii CCNP SWITCH Portable Command Guide Scott Empson Hans Roth Copyright 2010 Cisco Systems, Inc. Published by: Cisco Press 800 East 96th Street Indianapolis, IN 46240 USA All rights reserved. No part of
PT Activity 4.4.1: Basic VTP Configuration
Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13 255.255.255.0
KIM DONNERBORG / RTS. Cisco Lab Øvelse Af Kim Donnerborg / RTS. Side 0 af 8
KIM DONNERBORG / RTS Side 0 af 8 INDHOLDSFORTEGNELSE Lab: Basic Router Configuration... 2 Topology Diagram... 2 Addressing Table... 2 Learning Objectives... 2 Scenario... 2 Task 1: Cable the Network....
VLANs. Traditional Campus Networks. Performance Issues. Broadcast Issues. Bridges terminate collision domains
Traditional Campus Networks Broadcast Domain VLANs Collision Domain 1 Collision Domain 2 Bridges terminate collision domains 2003, Cisco Systems, Inc. All rights reserved. 2-1 2003, Cisco Systems, Inc.
VLANs. 2003, Cisco Systems, Inc. All rights reserved. 2-1
VLANs 2003, Cisco Systems, Inc. All rights reserved. 2-1 Traditional Campus Networks Broadcast Domain Collision Domain 1 Collision Domain 2 Bridges terminate collision domains 2003, Cisco Systems, Inc.
VLANs. 2003, Cisco Systems, Inc. All rights reserved. 2-1
VLANs 2003, Cisco Systems, Inc. All rights reserved. 2-1 Traditional Campus Networks Broadcast Domain Collision Domain 1 Collision Domain 2 Bridges terminate collision domains 2003, Cisco Systems, Inc.
The following graphic shows a single switch VLAN configuration.
7.1. VLAN A Virtual LAN (VLAN) can be defined as: Broadcast domains defined by switch port rather than network address. A grouping of devices based on service need, protocol, or other criteria rather than
Ch. 9 VTP (Trunking, VTP, Inter-VLAN Routing) CCNA 3 version 3.0
Ch. 9 VTP (Trunking, VTP, Inter-VLAN Routing) CCNA 3 version 3.0 Overview Explain the origins and functions of VLAN trunking Describe how trunking enables the implementation of VLANs in a large network
Question No : 1 Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)
Volume: 149 Questions Question No : 1 Which three of these statements regarding 802.1Q trunking are correct? (Choose three.) A. 802.1Q native VLAN frames are untagged by default. B. 802.1Q trunking ports
IEEE 802.1Q Configuration
CHAPTER15 This chapter describes: IP Routing over IEEE 802.1Q InterVLAN Routing and 802.1Q Trunking IP Routing over IEEE 802.1Q This section provides procedures for configuring protocols supported with
VLAN Range. Feature Overview
VLAN Range Feature History Release 12.0(7)XE 12.1(5)T 12.2(2)DD Modification The interface range command was introduced. The interface range command was integrated into Cisco IOS Release 12.1(5)T. The
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
Lab Catalyst 2950T and 3550 Series Basic Setup
Lab 1.2.9.1 Catalyst 2950T and 3550 Series Basic Setup Objective Configure a Cisco Catalyst 2950T or 3550 series Ethernet switch for the first time using the command-line interface (CLI) mode. Basic first
Using Packet Tracer to Build a Network
Using Packet Tracer to Build a Network We will be using Packet Tracer today to create the following network. This topology requires one 2811 router two 2960 switches and three workstations. Launch Packet
Lab 6.4.2: Challenge Inter-VLAN Routing
Lab 6.4.2: Challenge Inter-VLAN Routing Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 192.168.99.11 255.255.255.0 192.168.99.1 S2 VLAN
et Su cc es s in Passing Yourertification Exam at first
www.dumpspdf.com in Passing Yourertification Exam at first et Su cc es s Vendor: Cisco Exam Code: 200-101 Exam Name: Interconnecting Cisco Networking Devices Part 2 QUESTION: 1 **Exhibit Missing** A technician
Maintaining Specific VLAN Identification. Comparing ISL and 802.1Q. VLAN Trunking
Maintaining Specific VLAN Identification Specifically developed for multi-vlan interswitch communications Places a unique identifier in each frame Functions at Layer 2 2003, Cisco Systems, Inc. All rights
STUDENT LAB GUIDE CCNA ( )
STUDENT LAB GUIDE CCNA (640-802) Developed By, Router Infotech Career Academy LAB: 09 Static Route Configuration Objective: To configure & implement Static Route successfully on said devices and test its
Configuring Flex Links and the MAC Address-Table Move Update Feature
CHAPTER 19 Configuring Flex Links and the MAC Address-Table Move Update Feature This chapter describes how to configure Flex Links, a pair of interfaces on the Catalyst 3560 switch that provide a mutual
Chapter 3: VLANs. Routing & Switching
Chapter 3: VLANs Routing & Switching VLAN Definitions A VLAN is a logical partition of a Layer 2 network. VLANs logically group hosts, regardless of physical location. Multiple partitions can be created,
LAN Switching and Wireless
LAN Switching and Wireless CCNA Exploration Labs and Study Guide Allan Johnson ii LAN Switching and Wireless, CCNA Exploration Labs and Study Guide LAN Switching and Wireless CCNA Exploration Labs and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
Question 5.1. Every port on a switch is a collision domain. Every port on a router is a collision domain.
Question 5.1 Q 5.1.1 Number of Collision Domains: = 14 Every port on a switch is a collision domain. Every port on a router is a collision domain. Number of Broadcast Domains: = 5 Every port on a router
Table of Contents. Cisco Using One DHCP Server for Voice and Data Networks
Table of Contents Using One DHCP Server for Voice and Data Networks1 Document ID: 19580..1 Introduction.1 Prerequisites1 Requirements1 Components Used..1 Conventions..1 Problem.2 Solution.2 The Network
The following steps should be used when configuring a VLAN on the EdgeXOS platform:
EdgeXOS VLANs VLAN Overview This document provides an overview of what a VLAN is and how it is configured on the EdgeXOS platform. Use the step-by-step guide below to configure a VLAN on the Edge appliance
3/22/2016 ดร. ธน ญช ย ตร ภาค. Floor 4 : การตลาด 20 เคร อง. Floor 3 : งานบ คคล 10 เคร อง. Floor 2 : งานขาย 15 เคร อง. Floor 1 : การเง น 20 เคร อง
ดร. ธน ญช ย ตร ภาค 1 Floor 4 : การตลาด 20 เคร อง Floor 3 : งานบ คคล 10 เคร อง Floor 2 : งานขาย 15 เคร อง Floor 1 : การเง น 20 เคร อง 2 1 Floor 4 : การตลาด 20 เคร อง การเง น 3 เคร อง Floor 3 : งานบ คคล
Configuring VLAN-VPN CHAPTERS
CHAPTERS 1. VLAN-VPN 2. Basic VLAN-VPN Configuration 3. Flexible VLAN-VPN Configuration 4. Configuration Example 5. Appendix: Default Parameters VLAN-VPN This guide applies to: T2600G-28TS v3 or above,
3.2.7 switch#configure terminal switch(config)#spanning-tree mode pvst switch(config)#spanning-tree extend systemid switch(config)#vlan 1 switch(config-vlan)#exit switch(config)#vlan 10 switch(config-vlan)#exit
Lab 7.5.3: Troubleshooting the Wireless WRT300N
Lab 7.5.3: Troubleshooting the Wireless WRT300N Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway Fa0/1.5 5.5.5.10 255.255.255.0 N/A Fa0/1.10 192.168.10.1 255.255.255.0
Lab 1 Implementing VLANs
Lab 1 Implementing VLANs Task 1 Create VLAN 20 and VLAN 30 and assign name Admin and Engineer to each VLAN. Configure ports g0/0 g 0/3 as access-ports and assign VLAN 20 to ports g0/0 and g0/2. Assign
Configuring Access and Trunk Interfaces
Configuring Access and Trunk Interfaces Ethernet interfaces can be configured either as access ports or trunk ports. Trunks carry the traffic of multiple VLANs over a single link and allow you to extend
Configuring Protocol VLAN
CHAPTERS 1. Overview 2. Protocol VLAN Configuration 3. 4. Appendix: Default Parameters Overview This guide applies to: T1500G-10PS v2 or above, T1500G-8T v2 or above, T1500G-10MPS v2 or above, T1500-28PCT
PT Activity 2.5.1: Basic Switch Configuration
Topology NOTE TO USER: This activity is a variation of Lab 2.5.1. Packet Tracer may not support all the tasks specified in the hands-on lab. This activity should not be considered equivalent to completing
Lab 9.1.5b Trunking with 802.1q
Lab 9.1.5b Trunking with 802.1q Objective Create a basic switch configuration and verify it. Create multiple VLANs, name them and assign multiple member ports to them. Create an 802.1q trunk line between
Chapter 5: Inter-VLAN Routing. Routing & Switching
Chapter 5: Inter-VLAN Routing Routing & Switching What is Inter-VLAN routing? Layer 2 switches cannot forward traffic between VLANs without the assistance of a router. Inter-VLAN routing is a process for
Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0)
Interconnecting Cisco Networking Devices Part 2 (ICND2 v3.0) Cisco 200-105 Dumps Available Here at: /cisco-exam/200-105-dumps.html Enrolling now you will get access to 170 questions in a unique set of
Lab Catalyst 2950T and 3550 Series Static VLANS
Lab 2.9.1 Catalyst 2950T and 3550 Series Static VLANS Objective Create and maintain VLANs on a Cisco Catalyst 2950T or 3550 series Ethernet switch using the command-line interface (CLI) mode. Scenario
Configuring Flex Links and the MAC Address-Table Move Update Feature
CHAPTER 23 Configuring Flex Links and the MAC Address-Table Move Update Feature This chapter describes how to configure Flex Links, a pair of interfaces on the Catalyst 3750-X or 3560-X switch that provide
802.1Q Tunneling (Q-in-Q) Configuration Example NetworkLessons.com
1 sur 12 28/03/2018 à 17:28 2 sur 12 28/03/2018 à 17:28 3 sur 12 28/03/2018 à 17:28 4 sur 12 28/03/2018 à 17:28 R1(config)#interface fastethernet 0/0 R1(config-if)#no shutdown R1(config-if)#interface fastethernet
Document Configurations for Standardization across the Camera. Network. Kevin O Neal. DeVry University. NETW206: Introduction to Switching
Document Configurations for Standardization across the Camera Network Kevin O Neal DeVry University NETW206: Introduction to Switching Submitted to: Professor: Hopkins Date: 8-5-2012 To standardize the
3.2.7 switch# switch#configure terminal switch(config)#spanning-tree mode pvst switch(config)#spanning-tree extend systemid switch(config)#vlan 1 switch(config-vlan)#exit switch(config)#vlan 10 switch(config-vlan)#exit
Implementing Inter-VLAN Routing. 2003, Cisco Systems, Inc. All rights reserved. 2-1
Implementing Inter-VLAN Routing 2003, Cisco Systems, Inc. All rights reserved. 2-1 Internetwork Communications C:>ping 172.16.30.100 Can two hosts on different subnets communicate without a router? No
Device Interface IP Address Subnet Mask Default Gateway. Ports Assignment Network
Felix Rohrer Topology Diagram Addressing Table Device Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13
Lab Inter-VLAN Routing with the Internal Route Processor
Lab 5.3.4.1 Inter-VLAN Routing with the Internal Route Processor Objective Scenario The purpose of this lab is to configure Inter-VLAN routing using a switch with an internal route processor. The network
EtherSwitch Service Module (ES) Configuration Example
EtherSwitch Service Module (ES) Configuration Example Document ID: 82288 Contents Introduction Prerequisites Requirements Components Used Related Products Conventions EtherSwitch Modules Concepts Configure
Lab 3-2 Modifying Default Spanning Tree Behavior
Lab 3-2 Modifying Default Spanning Tree Behavior Objective The purpose of this lab is to observe what happens when the default spanning tree behavior is modified. Scenario Four switches have just been
OSPF single area configuration lab on packet tracer
OSPF single area configuration lab on packet tracer This OSPF lab is created in packet tracer and you will learn the OSPF single area configuration from this lab. Configuring the OSPF Routing Process This
Implementing Inter-VLAN Routing
Internetwork Communications C:>ping 72.6.30.00 Implementing Inter-VLN Routing Can two hosts on different subnets communicate without a router? No What would happen if a host tried to ping another host?
CCNA TECHNOLOGIES SERIES
CCNA TECHNOLOGIES SERIES ONLINE TRAINING CLASS CHAPTER 01 BURMESE VERSION Phyo Phyo Hein B. C. Tech (hons) MTCNA, MTCRE, MTCWE, MTCTCE, MTCUME, MTCINE CCNA R&S, CCNP R&S, CCIP, JNCIA-Junos, JNCDA May 15,
26 CHAPTER Virtual Private Networks (VPNs) provide a secure way for customers to share bandwidth over an ISP backbone network. A VPN is a collection of sites sharing a common routing table. A customer
STUDENT LAB GUIDE CCNA ( )
STUDENT LAB GUIDE CCNA (640-802) Developed By, Router Infotech Career Academy LAB: 18 RAPID SPANNING TREE PROTOCOL (RSTP) Objective: To configure & Verify Rapid Spanning Tree Protocol (RSTP) successfully
Lab 5: Basic VLAN Configuration
Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask Default Gateway S1 VLAN 99 172.17.99.11 255.255.255.0 N/A S2 VLAN 99 172.17.99.12 255.255.255.0 N/A S3 VLAN 99 172.17.99.13
Table of Contents. co Configuring InterVLAN Routing and ISL/802.1Q Trunking on a Catalyst 2900XL/3500XL/2950 Switch Using An Extern
outing and ISL/802.1Q Trunking on a Catalyst 2900XL/3500XL/2 co Configuring InterVLAN Routing and ISL/802.1Q Trunking on a Catalyst 2900XL/3500XL/2950 Switch Using An Extern Table of Contents Configuring
Configuring Layer 3 Interfaces
This chapter contains the following sections: Information About Layer 3 Interfaces, page 1 Licensing Requirements for Layer 3 Interfaces, page 4 Guidelines and Limitations for Layer 3 Interfaces, page
Chapter 4 Lab 4-1, Inter-VLAN Routing with an External Router
Chapter 4 Lab 4-1, Inter-VLAN Routing with an External Router Topology Objective Background Configure inter-vlan routing using an external router, also known as a router on a stick. Inter-VLAN routing
Configuring Secure (Router) Mode, Redundancy, Fault Tolerance, and HSRP
CHAPTER 4 Configuring Secure (Router) Mode, Redundancy, Fault Tolerance, and HSRP This chapter describes how to configure the following aspects of content switching that are necessary for the Content Services
Lab VTP Client and Server Configurations
Lab 9.2.5 VTP Client and Server Configurations Objective Create a basic switch configuration and verify it. Create multiple VLANs, name them and assign multiple member ports to them. Configure the VTP
CCNA Basic Questions. Question 1. What is the first 24 bits in a MAC address called? A. NIC B. BIA C. OUI D. VAI. Answer: C.
CCNA Basic Questions http://www.9tut.com/new-ccna-basic-questions Question 1 What is the first 24 bits in a MAC address called? A. NIC B. BIA C. OUI D. VAI Answer: C Question 2 Which of the following statements
LAB 3 Basic Switch Configuration Commands
LAB 3 Basic Switch Configuration Commands This lab explains basic switch configuration commands in detail with examples. Configuration and commands explained in this tutorial are essential commands to
Configuring Flex Links and the MAC Address-Table Move Update Feature
CHAPTER 20 Configuring Flex Links and the MAC Address-Table Move Update Feature This chapter describes how to configure Flex Links, a pair of interfaces on the switch that provide a mutual backup. It also
SEDINTA 2. Configurare VTP propagarea VLANrilor in cadrul retelei interne. VTP = VLAN Trunking Protocol
SEDINTA 2 Configurare VTP propagarea VLANrilor in cadrul retelei interne VTP = VLAN Trunking Protocol - allows for the propagation of VLAN s from a single switch to multiple switches (Server-Client architecture)
Lab Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking
Lab 2.3.7.1 Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking Objective Configure a VLAN trunk between two Cisco Catalyst WS-C2950T-24-EI switches and a Cisco Catalyst WS-C3550-24-EMI switch
Number: Passing Score: 800 Time Limit: 120 min File Version: 1.0. Cisco Certified Network Associate
200-120 Number: 000-000 Passing Score: 800 Time Limit: 120 min File Version: 1.0 http://www.gratisexam.com/ Cisco Certified Network Associate Экзамен A QUESTION 1 What is the first 24 bits in a MAC address
Lab Configuring 802.1Q Trunk-Based Inter-VLAN Routing Topology
Topology 2016 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 7 Addressing Table Device Interface IP Address Subnet Mask Default Gateway R1 G0/1.1 192.168.1.1
CCNA Explorer 1 Chapter 11 Configuring & Testing Your Network
CCNA Explorer 1 Chapter 11 Configuring & Testing Your Network 11.1.1 What is the system software in Cisco devices? The Cisco IOS provides devices with what network services? How is the IOS generally accessed?
RealCiscoLAB.com. Configure inter-vlan routing with HSRP to provide redundant, fault-tolerant routing to the internal network.
RealCiscoLAB.com CCNPv6 SWITCH Hot Standby Router Protocol Topology Objective Background Configure inter-vlan routing with HSRP to provide redundant, fault-tolerant routing to the internal network. Hot
CS IT ports switch basic configuration. Lecture (01) Introduction to 24 ports managed switches By: Dr. Ahmed ElShafee.
Lecture (01) Introduction to 24 ports managed switches By: Dr. Ahmed ElShafee CS IT Agenda 24 ports switch basic configuration Switch remote configuration peer2peer star network clients/server star network
Implement Inter-VLAN Routing. LAN Switching and Wireless Chapter 6 Modified by Tony Chen 11/01/2008
Implement Inter-VLAN Routing LAN Switching and Wireless Chapter 6 Modified by Tony Chen 11/01/2008 ITE I Chapter 6 2006 Cisco Systems, Inc. All rights reserved. Cisco Public 1 Notes: If you see any mistake
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and
This document is exclusive property of Cisco Systems, Inc. Permission is granted to print and copy this document for non-commercial distribution and exclusive use by instructors in the CCNA Exploration:
Describing the STP. Enhancements to STP. Configuring PortFast. Describing PortFast. Configuring. Verifying
Enhancements to STP Describing the STP PortFast Per VLAN Spanning Tree+ (PVST+) Rapid Spanning Tree Protocol (RSTP) Multiple Spanning Tree Protocol (MSTP) MSTP is also known as Multi-Instance Spanning
Configuring a Management IP Address on Catalyst 4500/4000, 5500/5000, 6500/6000, and Catalyst Fixed Configuration Switches
Configuring a Management IP Address on Catalyst 4500/4000, 5500/5000, 6500/6000, and Catalyst Fixed Configuration Switches Document ID: 10594 Interactive: This document offers customized analysis of your
Command Reference for Voice VLAN
APPENDIX A This section provides reference information for the following voice VLAN commands: interface range, page A-1 interface vlan, page A-3 monitor session, page A-4 spanning-tree, page A-6 spanning-tree
Learning and Teaching the Communication Between VLANs with Three Layer Switch
3rd International Conference on Management, Education, Information and Control (MEICI 2015) Learning and Teaching the Communication Between VLANs with Three Layer Switch * Henghua SHI 1, a, Renlong ZHANG
Implementing Inter-VLAN Routing
Internetwork Communications C:>ping 172.16.30.100 Implementing Inter-VLAN Routing Can two hosts on different subnets communicate without a router? No What would happen if a host tried to ping another host?
Antonio Cianfrani. Virtual LAN (VLAN)
Antonio Cianfrani Virtual LAN (VLAN) Ethernet Ethernet standard (IEEE 802.3) for Local Area Network (LAN). CSMA/CD (Carrier Sense Multiple Access/Collision Detection) Carrier Sense: all devices have to
SOHO. A Case Study. Case Study: SOHO
SOHO A Case Study Authors: Mary Hawkins & Patrick Neff - 2006 Page 1 of 21 Core Area These routers connect to the various offices and to the core router to ensure that all offices are able to connect to
switch# switch#configure terminal switch(config)#spanning-tree mode pvst switch(config)#spanning-tree extend system-id switch(config)#vtp mode transparent switch(config)#vlan 4093 Switch(config-vlan)#exit
Lab Configure Extended VLANs, VTP, and DTP
Topology Addressing Table Objectives Part 1: Configure VTP Part 2: Configure DTP Table Heading Interface IP Address Subnet Mask S1 VLAN 99 192.168.99.1 255.255.255.0 S2 VLAN 99 192.168.99.2 255.255.255.0
Lab Classifying Traffic using Class of Service at the Access Layer
Lab 8.9.1 Classifying Traffic using Class of Service at the Access Layer Objective For effective quality of service (QoS) it is important to classify traffic as soon as possible. This allows routing and
Device Interface IP Address Subnet Mask R1 G0/ N/A
CSNB214 Packet Tracer Topology Addressing Table Device Interface IP Address Subnet Mask Default Gateway Objectives R1 G0/0 192.168.20.1 255.255.255.0 N/A S1 VLAN 10 S2 VLAN 10 G0/1 192.168.10.1 255.255.255.0
Lab STP configuration on Catalyst 1900 Command Line Interface
Lab STP configuration on Catalyst 1900 Command Line Interface Estimated Time: 30 mins Objectives: Background: To gain a better understanding of how STP works. To be able to configure and monitor STP on
CHAPTER 1 LAN Design
CHAPTER 1 LAN Design As a business grows, so does its networking requirements. To keep pace with a business s expansion and new emerging technologies, a network must be designed to scale. A network that
Configuring Layer 3 Interfaces
This chapter contains the following sections: Information About Layer 3 Interfaces, page 1 Licensing Requirements for Layer 3 Interfaces, page 4 Guidelines and Limitations for Layer 3 Interfaces, page
Lab Troubleshooting VTP Configuration
Lab 4.4.3 Troubleshooting VTP Configuration Topology Diagram Addressing Table Device (Hostname) Interface IP Address Subnet Mask S1 VLAN 99 172.17.99.11 255.255.255.0 S2 VLAN 99 172.17.99.12 255.255.255.0
Configuring Private VLANs
36 CHAPTER This chapter describes private VLANs (PVLANs) on Catalyst 4500 series switches. It also provides restrictions, procedures, and configuration examples. This chapter includes the following major
Comparison of Routing Protocols RIP, OSPF and EIGRP
Comparison of Routing Protocols RIP, OSPF and EIGRP Kamal Grover 1, Palak Bansal 2, RanjanVenkatachala Shetty 3 1 Department of Computer Science and Engineering, National Institute of Technology Jalandhar
Route between VLANs using a 3560 switch with an internal route processor using Cisco Express Forwarding (CEF).
Lab 3- Part I Inter-VLAN routing with a Multilayer Switch Configuration and Management of Networks - 2014 Topology Objective Route between VLANs using a 3560 switch with an internal route processor using
Lab Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking
Lab 2.9.2 Catalyst 2950T and 3550 Series VTP Domain and VLAN Trunking Objective Configure a VLAN trunk between two Cisco Catalyst WS-C2950T-24-EI switches and a Cisco Catalyst WS-C3550-24-EMI switch in
CCNP Switch Questions/Answers Labs
Acme is small export company that has an existing enterprise network comprised of 5 switches; CORE, DSW1, DSW2, ASW1 and ASW2. The topology diagram indicates their desired pre-vlan spanning tree mapping.