FS016 V1.0 January Wireless AP/Router Quick Installation Guide

Transcription

1 FS06 V.0 January 07 Wireless /Router Quick Installation Guide

2 Installation Diagram Solution Solution Internet Internet AC CORE GATEWAY CORE SWITCH POE POWER SUPPLY POE SWITCH POE SWITCH Note: Solution (Single Device Setting): Get into the web setting page independently. Solution (Multiple Devices Setting): Do centralized management and local portal by AC core gateway. (POE power supply and other devices are not standard, please refer to the packing list. ) Installation. Ceiling-mounted Installation Ceiling ①Remove the chassis of the, and fix it on the ceiling by screws. ②Connect the LAN port of the device by cable. (If there are multiple devices, please connect the WAN port of the device by cable for centralized management.) Ceiling ③Fix chassis on the appropriately.

3 . Wall-mounted Installation wall wall ①Remove the chassis of the, and fix it on the ceiling by screws. ②Connect the LAN port ③Fix chassis on the of the device by cable. (If appropriately. there are multiple devices, please connect the WAN port of the device by cable for centralized management.) Note: This quick installation guide is taken the circled ceiling for an example. Some of square ceiling have screws and please push one side to install. Single Device Configuration. Connection Diagram POE Power Supply (Not Standard) Higher Level Note: Set the LAN port of the device to the computer.. Set the computer to obtain the automatically, and connect the LAN port of the device to the device management interface.

4 . Open the computer browser, and input to get into the device login page. The device is defaulted as Router Mode. When you login at the first time, you need to set a password. The device language has Chinese and to be chosen, and you can set up the language by the top right corner icon. Language Settings 简体中文 Please enter password login. When you get into the setting page, there are three working modes in the : PPPOE, Static IP and Dynamic IP. SWITCH LAN LAN MODEM Router

5 .5 Click mode and set up IP Address and Subnet Mask. The and should be within same network segment as upper network and can t be conflict with from upper network router. After setting, you can visit the device from the that you have set just now by connecting internet with WAN port of the device. Notes: ① In mode, the from the other devices connected to the will be allocated by the upper network router. ② According to the defaulted setting, there is no need to change. If you want to manage the device, just manually set in the computer. WiFi.G Users Mode: You can set up wireless SSID, password and channel in advanced. After setting, other mobile devices can connect the device SSID to surf the internet. WiFi.G SSID Users.G wireless Enter or 8- Characters Advanced setting Bandwidth 0MHz Country China Channel auto

6 WiFi.G Users.G SSID Mode: Please ensure that WDS in the upper network is enabled. device can set up intranet segment, and then select the wireless SSID signal you need to bridge and input wireless password. The password is the same as your upper network router. Wireless WiFi.G Refresh Scan Results NO. BSSID SSID Channel 0:A5:EF:8:E6: unknown 0:A5:EF:8:DE:6 unknown 0:A5:EF:85:8: unknown 00:E0:C:8:96:D 5 0:A5:EF:8:E6: unknown 6 0:A5:EF:8:DE:6 unknown 7 0:A5:EF:80:97:6 E5N_80976 Operation

7 Wireless WiFi.G Scan Bind.GHz SSID scan Enter or 8- Characters ① Select DHCP and the device will automatically receive IP address segment from the upper network. Wireless WiFi.G Static DHCP Gateway DNS ② Select Static and you need to manually input and ensure that the segment should be the same as the upper network. ( can not be conflict with the upper network device.) Wireless WiFi.G Static DHCP e.g: xxx.xxx.xxx.xxx e.g: xxx.xxx.xxx.xxx Gateway DNS e.g: e.g: ③ Set up SSID and password for this device and click to.

8 Wireless WiFi.G.G Wireless SSID Wireless WiFi.G STA SSID.G SSID Router Mode: There are three ways to surf the internet which are PPPOE, Static and DHCP. SWITCH LAN LAN MODEM Router ① PPPOE: It needs to fill in the account number and password, which are provided by ISP.

9 WiFi.G PPPoE DHCP Static User Max Length 6 characters Max Length 6 characters 9 MTU Max Length 6 characters Service name WiFi.G WiFi.G.G Wireless SSID advanced setting Bandwidth 0MHz Country China Channel auto WiFi.G Router.G SSID

10 ② Static: It needs to fill in, Subnet Mask, Gateway and DNS, which are provided by ISP. WiFi.G PPPoE DHCP Static e.g: xxx.xxx.xxx.xxx e.g: xxx.xxx.xxx.xxx Gateway DNS e.g: e.g: WiFi.G WiFi.G.G Wireless SSID advanced setting Bandwidth 0MHz Country China Channel auto WiFi.G Router.G SSID

11 ③ DHCP: It needs to be allocated IP by the upper network device then you can surf the internet. WiFi.G PPPoE DHCP Static Gateway DNS WiFi.G WiFi.G.G Wireless SSID advanced setting Bandwidth 0MHz Country China Channel auto Router.G SSID WiFi.G

12 Copyright Statement No part of this manual shall be copied, reproduced, transcribed or translated in any form or by any means without the prior written consent of. Product specifications and information mentioned in this manual are for reference. Any updated information shall not be announced. Copyright All Rights Reserved. All statements and information are not constitute any form of guarantee. FS trademark and FS logo belong to.