Brocade SilkWorm Switches Supports Management Module SM-BRC1000

Transcription

1 Brocade SilkWorm Switches Supports Management Module SM-BRC1000 SPECTRUM Device Management

2 This documentation (the "Documentation") and related computer software program (the "Software") (hereinafter collectively referred to as the "Product") is for the end user's informational purposes only and is subject to change or withdrawal by CA at any time. This Product may not be copied, transferred, reproduced, disclosed, modified or duplicated, in whole or in part, without the prior written consent of CA. This Product is confidential and proprietary information of CA and protected by the copyright laws of the United States and international treaties. Notwithstanding the foregoing, licensed users may print a reasonable number of copies of the Documentation for their own internal use, and may make one copy of the Software as reasonably required for back-up and disaster recovery purposes, provided that all CA copyright notices and legends are affixed to each reproduced copy. Only authorized employees, consultants, or agents of the user who are bound by the provisions of the license for the Software are permitted to have access to such copies. The right to print copies of the Documentation and to make a copy of the Software is limited to the period during which the license for the Product remains in full force and effect. Should the license terminate for any reason, it shall be the user's responsibility to certify in writing to CA that all copies and partial copies of the Product have been returned to CA or destroyed. EXCEPT AS OTHERWISE STATED IN THE APPLICABLE LICENSE AGREEMENT, TO THE EXTENT PERMITTED BY APPLICABLE LAW, CA PROVIDES THIS PRODUCT "AS IS" WITHOUT WARRANTY OF ANY KIND, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT. IN NO EVENT WILL CA BE LIABLE TO THE END USER OR ANY THIRD PARTY FOR ANY LOSS OR DAMAGE, DIRECT OR INDIRECT, FROM THE USE OF THIS PRODUCT, INCLUDING WITHOUT LIMITATION, LOST PROFITS, BUSINESS INTERRUPTION, GOODWILL, OR LOST DATA, EVEN IF CA IS EXPRESSLY ADVISED OF SUCH LOSS OR DAMAGE. The use of this Product and any product referenced in the Documentation is governed by the end user's applicable license agreement. The manufacturer of this Product is CA. This Product is provided with "Restricted Rights." Use, duplication or disclosure by the United States Government is subject to the restrictions set forth in FAR Sections , , and (c)(1) - (2) and DFARS Section (c)(1)(ii), as applicable, or their successors. All trademarks, trade names, service marks, and logos referenced herein belong to their respective companies. Copyright 2006 CA. All rights reserved. Device Management Page 2 Brocade SilkWorm Switches

3 Contents INTRODUCTION 5 Purpose and Scope...5 Required Reading...5 Supported Devices...6 The SPECTRUM Model...6 TASKS 8 FIBRE CHANNEL PORT INTERFACE MANAGEMENT 9 DEVICE VIEW 11 Interface Icons...12 Interface Icon Subviews Menu...13 Secondary Address Panel...14 DEVICE TOPOLOGY VIEW 15 SWITCHING INFORMATION 16 System Information View...16 Environment Information View...19 Fabric Information View...20 Agent Community Information View...21 Fibre Channel Port Information View...21 Name Server Information View...25 FW Thresholds Information View...26 FW Class Area Information View...27 Event Information View End Devices RLS Information View Bloom Performance Alpa Information View Bloom Performance End to End Performance View Bloom Performance Filter Base Information View Trunking Information View Trunk Group Information APPLICATION VIEWS 32 Main Application View Supported Applications Common Applications Device-Specific MIBs PERFORMANCE VIEWS 35 CONFIGURATION VIEWS 36 Device Configuration View MODEL INFORMATION VIEW 38 Device Management Page 3 Brocade SilkWorm Switches

4 Contents Contents TRAPS, EVENTS, AND ALARMS 39 Standard Trap Support...39 Device-Specific Trap Support...39 Proprietary Trap Descriptions...41 INDEX 42 Device Management Page 4 Brocade SilkWorm Switches

5 Introduction This section introduces the SPECTRUM Device Management documentation for the Brocade SilkWorm Switch. This introduction contains the following topics: Purpose and Scope Required Reading Supported Devices (Page 6) The SPECTRUM Model (Page 6) Purpose and Scope Use this document as a guide for managing the Brocade SilkWorm Switch devices described on Page 6 with SPECTRUM management module SM-BRC1000. This document describes the icons, menus, and views that enable you to remotely monitor, configure, and troubleshoot Brocade SilkWorm Switch devices through software models in your SPECTRUM database. For general information about device management using SPECTRUM and explanations of SPECTRUM functionality and navigation techniques, refer to the topics listed under Required Reading. Required Reading To use this documentation effectively, you must be familiar with the information covered by the other SPECTRUM online documents listed below. Getting Started with SPECTRUM for Operators Getting Started with SPECTRUM for Administrators How to Manage Your Network with SPECTRUM SPECTRUM Views SPECTRUM Menus SPECTRUM Icons SPECTRUM Software Release Notice Device Management Page 5 Brocade SilkWorm Switches

6 Introduction Supported Devices SPECTRUM management module SM-BRC1000 currently lets you model the following Brocade SilkWorm Switch. SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Entry-level Fibre Channel Switch SilkWorm port Fibre Channel Switch SilkWorm port Fibre Channel Switch SilkWorm 3200 Entry Fabric Switch SilkWorm 3800 Enterprise Fabric Switch SilkWorm 3900 Enterprise Fabric Switch SilkWorm Director SilkWorm SilkWorm 3250 SilkWorm 3850 SilkWorm AP7420 SilkWorm SilkWorm Spider 2800 HP StorageWorks 2/16-EL HP StorageWorks 2/8 IBM BladeCenter HP Blade Center HP 4100 Dell Blade Center The SPECTRUM Model Supported Devices The model type for the Brocade SilkWorm Switch devices is SilkwormSw. Modeling results in the creation of Device icons that represent the devices and Application icons that represent their supported applications. The Device icons contain double-click zones and provide access to Icon Subviews menus that let you perform device management activities such as those listed in Tasks on Page 8. As Figure 1 shows, the appearance of the Device icons varies slightly depending on the kind of view it appears in. Device Management Page 6 Brocade SilkWorm Switches

7 Introduction The SPECTRUM Model Figure 1: Device Icons Option Accesses the... Model Name XYZ_Mxxx Large Device icon appears in Device Topology, Location, and Device Interface views. Small Device icon appears in Topology and Application views Model Name XYZ_Mxxx Device Topology Device Topology View (Page 15) Application Application Views (Page 32) Configuration Configuration Views (Page 36) Model Information Model Information View (Page 38) Primary Application Menu options that let you select either Gen. Bridge App or MIB-II as the primary application. The device-specific Icon Subviews menu options available from the Device icon are listed below. Option Fault Management Accesses the... Fault Management view, which is described in the How to Manage Your Network with SPECTRUM documentation. Device Device View (Page 11) The rest of this document covering management module SM-BRC1000 is organized as follows: Tasks (Page 8) Fibre Channel Port Interface Management (Page 9) Device View (Page 11) Device Topology View (Page 15) Application Views (Page 32) Performance Views (Page 35) Configuration Views (Page 36) Model Information View (Page 38). Traps, Events, and Alarms (Page 39) Device Management Page 7 Brocade SilkWorm Switches

8 Tasks This section provides a list of device management tasks, with each task providing one or more links to views that let you perform the task. Administrative Information (check) Model Information View (Page 38) Alarm Thresholds (set) Interface Icon Subviews Menu (Page 13) Configuration Information (check) Configuration Views (Page 36) Fibre Channel Port Configuration Fibre Channel Port Interface Management (Page 9) Performance (check) Device View (Page 11) Interface Icons (Page 12) Performance Views (Page 35) Port Status (check/change) Secondary Address Panel (Page 14) Topology (check) Device Topology View (Page 15) IP Address (find/change) Device View (Page 11) Secondary Address Panel (Page 14) Network Type (check) Network Type Label (Page 13) Device Management Page 8 Brocade SilkWorm Switches

9 Fibre Channel Port Interface Management This section describes fibre channel port model status indications and configuration options. Access: (OneClick) From the Explorer, select the SilkWorm switch model and then select the Interfaces tab in the Component Detail panel. Fibre channel port interface models enable you to monitor and manage server and storage device connections supported by the SilkWorm switch in the Storage Area Network. Figure 2 shows an example list of fibre channel port interface models. Each entry includes detailed information about a port. Figure 2: Fibre Channel Port Interfaces Figure 3 shows an example Component Detail view of a fibre channel port interface. It includes port-specific configuration options. Device Management Page 9 Brocade SilkWorm Switches

10 Fibre Channel Port Interface Management Figure 3: Fibre Channel Port Component Detail Device Management Page 10 Brocade SilkWorm Switches

11 Device View This section describes the Device view and subviews available for models of Brocade SilkWorm Switch devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Device > Interface. This view (Figure 4) uses icons and labels to represent the device and its components, such as modules, ports, and applications. The view provides dynamic configuration and performance information for each of the device s serial and network I/O ports, which are represented by Interface icons in the bottom panel of the view. The middle panel of the view displays a Device icon, which lets you monitor the device operation and access other device-specific views. Figure 4: Device View SpectroGRAPH: Router Device: Model Name File View Tools Bookmarks Help Model Name Contact Description Location Model Name XYZ_Mxxx Network Address Primary Application Filter Physical Interface Description Device Icon Gen Bridge App Sys Up Time Manufacturer Device Type Serial Number Interface Options Panel 1 ON Ethernet ei0 0:0:1D:F:FD:B ON ATM CPU ON 4 ATM 7B ATM 8B ON 5 ON SFTWARLPBK lo0 0:0:1D:F:FD:B ON ATM port CPU ON ATM 7B ON ATM 8B ON ATM8023 zn1 0:0:1D:F:FD:B ON AAL5 UAAL5 10 ON ATM 7A ON ATM 7B ON ATM 8B ON ATM 8B2 Interface Icons Model Name of type XYZ_Mxxx of Landscape node: Primary Device Management Page 11 Brocade SilkWorm Switches

12 Device View Interface Icons Figure 5 shows a close-up of an Interface icon from the Device view. Most of the informational labels on the icon also provide double-click access to other views, as explained in the following label descriptions. Figure 5: a Interface Icon b Interface Number Label This label displays the interface (port) number. Interface Icons IF Status Label This label displays the current status of the interface for the primary application selected, e.g., Gen Rtr App or MIB-II App. Table 1 lists the possible label color representations. Note that the color of the label also depends on the interface s current Administrative Status, which you set in the Interface Configuration view. This view can be accessed by double-clicking the Interface Type label. a b c d e f 1 ON Table 1: Interface Status Label Colors ethernet c fxp0 d Operational Administrative Label Color Status Status Text 0:0:1D:F:FD:B6 e f Green up up ON Interface Number Label IF Status Label Interface Type Label Network Type Label Physical Address Label IP Address Label Blue down down OFF Yellow down up OFF Red testing testing TEST Interface Type Label This label identifies the interface type (Ethernet, ATM, etc.). Double-click this label to access the Interface Device view, see the SPECTRUM Views documentation. Device Management Page 12 Brocade SilkWorm Switches

13 Device View Network Type Label This label identifies the type of network to which the interface is connected. Double-click the label to open the Model Information view for the interface. Physical Address Label This label displays the physical (MAC) address of the interface. Double-click this label to open the IF Address Translation Table. IP Address Label This label displays the IP address for the interface. Doubleclick this label to open the Secondary Address Panel (Page 14), which lets you change the address and mask for the interface. Interface Icon Subviews Menu Table 2 lists the device-specific interface Icon Subviews menu options and the views to which they provide access. Detail Table 2: Option IF Configuration Sub-Layer Information Address Translation Table Secondary Address Panel Thresholds Interface Icon Subviews Menu Interface Icon Subviews Menu Accesses the... Interface Detail view, which displays packet, error, and discard breakdown statistics for the interface. Interface Configuration view. (See SPECTRUM Views). Sub-Layer Information view. (See SPECTRUM Views). Interface Address Translation Table, which identifies the physical and network address for the interface. Secondary Address Panel (Page 14). Interface Threshold view, which lets you set the on/off alarm thresholds for load, packet rate, error rate, and % discarded for the interface. Model Information Model Information View (Page 38). Trap Configuration Trap Configuration view (see the How to Manage Your Network with SPECTRUM documentation). Device Management Page 13 Brocade SilkWorm Switches

14 Device View Secondary Address Panel Secondary Address Panel Access: From the Icon Subviews menu for the Interface icon in the Device view, select Secondary Address Panel. This panel provides a table of IP addresses and masks obtained from the Address Translation table within the device s firmware. You can change the current address displayed in the IP Address field by selecting an entry from the table in this panel and clicking the Update button. Device Management Page 14 Brocade SilkWorm Switches

15 Device Topology View This section describes the Device Topology view available for models of the Brocade SilkWorm Switch devices. Access: From the Icon Subviews menu for the Device icon, select DevTop > interface. The Device Topology view (Figure 6) shows the connections between a modeled device and other network entities. The lower panel of the view uses Interface icons to represent the device s serial, network, and I/O ports. These icons provide the same information and menu options as those in the Device View (Page 11). If a device is connected to a particular interface, a Device icon appears on the vertical bar above the Interface icon along with an icon representing the network group that contains the device. Refer to the SPECTRUM Views documentation for details on Device Topology view. Figure 6: Device Topology View SpectroGRAPH: Device Topology: Model Name File View Tools Bookmarks Help Graphic of <manufacturer> Device Model Name XYZ_Mxxx 1 ON 2 ON 3 ON Ethernet ei0 0:0:1D:F:FD:B6 ATM A2 0:0:1D:F:FD:B6 ATM CPU 0:0:1D:F:FD:B Model Name of type Model Type of Landscape node: Primary Device Management Page 15 Brocade SilkWorm Switches

16 Switching Information This section describes the switching information available for the Brocade SilkWorm devices. The following views provide switching information for the Brocade SilkWorm devices: System Information View (Page 16) Environment Information View (Page 19) Fabric Information View (Page 20) Agent Community Information View (Page 21) Fibre Channel Port Information View (Page 21) Name Server Information View (Page 25) FW Thresholds Information View (Page 26) FW Class Area Information View (Page 27) Event Information View (Page 28) End Devices RLS Information View (Page 28) Bloom Performance Alpa Information View (Page 29) Bloom Performance End to End Performance View (Page 29) Bloom Performance Filter Base Information View (Page 30) Trunking Information View (Page 30) Trunk Group Information (Page 31) System Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > System. This view is divided into four separate sections and provides the following information. General Information Firmware Vers. The current version of the firmware. Soft Ser. Num. The serial number of the software. Oper Status The current operational status of the switch. Table 3 displays the possible states. Device Management Page 16 Brocade SilkWorm Switches

17 Switching Information System Information View. Table 3: Possible Operational States Table 4: Admin Status States State Definition Sate Definition Online Offline Testing Faulty The switch is accessible by an external Fibre Channel Port. The switch is not accessible. The switch is in a built-in test mode and is not accessible. The switch is not operational. Telnet Admin Status The desired administrative status of the Telnet shell. By setting it to terminated, the current Telnet shell task is deleted. When this variable is read, it reports the value last set through SNMP. Admin Status The desired administrative status of the switch. A management station may place the switch in a desired state by setting this button accordingly. Table 4 defines the possible states. Online Offline Testing Faulty Reboot Fastboot Track Changes String Displays the track changes string. This is for traps only. Last Updated This switch is accessible by a an external Fiber Channel Port. The switch is not accessible. The switch is in a built-in test mode and is not accessible. The switch is not operational. Set the switch to reboot in one second. Sets the switch to fastboot in one second. Fast causes the switch to boot but skip over the POST. Boot Date The date and time when the system last booted, in displaybale textual format. Boot Prom The date when the boot PROM was last updated, in displayable textual format. Device Management Page 17 Brocade SilkWorm Switches

18 Switching Information FLASH The date when the FLASH was last updated, in displayable textual format. Firmware The date when the firmware was last updated, in displayable textual format. FLASH Information Admin Status The desired state of the FLASH. Table 5 shows the possible values. swcurrent Table 5: State swfwupgrade swcfupload swcfdownload FLASH Admin States Definition The FLASH contains the current firmware image or config file. The firmware in the FLASH is to be upgraded from the host specified. The switch config file is to be uploaded to the host specified. The switch config file is to be downloaded from the host specified. System Information View Oper Status The operational status of FLASH. Table 6 displays the possible states. swcurrent Table 6: State swfwupgraded swcfuploaded swcfdownloaded FLASH Operational States Definition The FLASH contains the current firmware image or config file. Contains the image upgraded from the swflashdlhost.0. The switch configuration file has been uploaded to the host. The switch configuration file has been downloaded from the host. Password The password to be used for FTP transfer of files in the download or upload operation. User The user name on the host to download or upload a relevant file to or from the FLASH. Host The name or IP address (in dot notation) of the host to download or upload a relevant file to the FLASH. Device Management Page 18 Brocade SilkWorm Switches

19 Switching Information File The name of the file to be downloaded or uploaded. Misc Information POST Result The result of the power-on startup (POST) diagnostics. Sensors The number of sensors inside the switch. Beacon Admin Status The desired status of the switch beacon. When the beacon is set to on, the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is set to off, each LED will be in its regular status indicating color and state. Beacon Oper Status The current operational status of the switch beacon. When the beacon is on, the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is off, each LED will be in their its regular status indicating color and state. Environment Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Environment. This view provides the Sensor Table and the following information. Environment Information View Num Sensor The number of sensors inside the switch. Sensor Table Index Identifies the sensor. Type Identifies the sensor type. Status The current status of the sensor. Value The current value (reading) of the sensor. The value, , represents an unknown quantity. It also means that the sensor does not have the capability to measure the actual value. In V2.0, the temperature sensor value will be in Celsius; the fan value will be in RPM (revolution per minute); and the power supply sensor reading will be unknown. Info Additional displayable information on the sensor. In V2.x, it contains the sensor type and number in textual format. Device Management Page 19 Brocade SilkWorm Switches

20 Switching Information Fabric Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Fabric. This view provides the following information. Domain ID The current Fibre Channel domain ID of the switch. To set a new value, the switch (swadmstatus) must be in offline or testing state. Principal Switch Indicates whether the switch is the Principal switch as per FC-SW. Num Neighbors The number of Inter-Switch Links in the (immediate) neighborhood. Neighbor Table Index Identifies the neighbor ISL entry. Local Port This is a port that has an ISL to another switch. Remote Domain The Fibre Channel domain on the other end of the ISL. Remote Port The port index on the other end of the ISL. Baud Rate The baud rate of the ISL. State The current state of the ISL. Cost The current link cost of the ISL. Fabric Information View Remote Name The World_wide_Name of the remote port. Agent Community Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Agent Comm. This view provides the following information. Agent Community Index Identifies the SNMPv1 Community entry. Agent Community String The Community string supported by the agent. If a new value is set successfully, it takes effect immediately. Agent Trap Recipient The trap recipient associated with the Community. If a new value is set successfully, it takes effect immediately. Device Management Page 20 Brocade SilkWorm Switches

21 Switching Information Fibre Channel Port Information View Fibre Channel Port Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > FC Ports. This view provides the Port Table defined below: Port Capacity The maximum number of Fibre Channel ports on this switch. It includes G_Port, F_Port, FL_Port and any other types of Fibre Channel port. Index Identifies the switch port index. Note that the value of a port index is 1 higher than the port number labeled on the front panel. E.g. port index 1 correspond to port number 0. Type Identifies the type of switch port. It may be of type stitch, flannel, loom, bloom, rdbloom or wormhole. Physical State Identifies the physical state of the port. Table 7 show the possible values. nocard nogbic laserfault nolight nosync insync portfault diagfault lockref Table 7: State Possible Physical States Definition No card present in this switch slot. No GBIC module in this port. The module is signaling a laser fault (defective GBIC). The module is not receiving light. The module is receiving light but is out of sync. The module is receiving light and is in sync. The port is marked faulty (defective GBIC, cable or device). The port failed diagnostics (defective G_Port or FL_Port card or motherboard. the port is locking to the reference signal. Oper Status Identifies the operational status of the port. The online state indicates that user frames can be passed. The unknown state indicates that the port module is physically absent (see swfcportphystate). Device Management Page 21 Brocade SilkWorm Switches

22 Switching Information Admin Status The desired state of the port. A management station may place the port in a desired state by setting this object accordingly. The testing state indicates that no user frames can be passed. As the result of either explicit management action or per configuration information accessible by the switch, swfcportadmstatus is then changed to either the online or testing states, or remains in the offline state. Link State The link state of the port. The possible value are: enabled, disabled, and loopback. The port may transmit frames through an internal path to verify the health of the transmitter and receiver path. TX Type The media transmitter type of the port. Table 8 show the possible values. unknown lw sw ld cu Table 8: State Possible TX States Definition Cannot determine the port driver. Long wave laser. Short wave laser. Long wave LED. Copper Electral. Note: Fibre Channel Port Information View Not that here is a new type of GBIC which has a serial ID and will be mapped as unknown for the current firmware revision. TX Words Counts the number of Fibre Channel words that the port has transmitted. RX Words Counts the number of Fibre Channel words that the port has received. TX Frames Counts the number of (Fibre Channel) frames that the port has transmitted. RX Frames Counts the number of (Fibre Channel) frames that the port has received. RX C2 Frames Counts the number of Class 2 frames that the port has received. RX C3 Frames Counts the number of Class 3 frames that the port has received. Device Management Page 22 Brocade SilkWorm Switches

23 Switching Information RX LCs Counts the number of Link Control frames that the port has received. RX Mcasts Counts the number of Multicast frames that the port has received. Too Many RDYs Counts the number of times when RDYs exceeds the frames received. No Tx Credits Counts the number of times when the transmit credit has reached zero. RX Enc In Frs Counts the number of encoding error or disparity error inside frames received. Rx CRCs Counts the number of CRC errors detected for frames received. RX Truncs Counts the number of truncated frames that the port has received. RX Too Longs Counts the number of received frames that are too long. Fibre Channel Port Information View Rx Bad EOFs Counts the number of received frames that have bad EOF delimiter. RX Enc Out Frs Counts the number of encoding error or disparity error outside frames received RX Bad Os Counts the number of invalid Ordered Sets received. C3 Discards Counts the number of Class 3 frames that the port has discarded. Tx Mcasts Counts the number of Multicast frames that has been transmitted. Mcasts Time Outs Counts the number of Multicast frames that has been timed out. Lip Ins Counts the number of Loop Initialization that has been initiated by loop devices attached. Lip Outs Counts the number of Loop Initializations that has been initiated by the port. Device Management Page 23 Brocade SilkWorm Switches

24 Switching Information Lips Last Alpa The Physical Address (AL_PA) of the loop device that initiated the last Loop Initialization. World Wide Name The World_Wide_Name of the Fibre Channel port. The contents of an instance are in the IEEE extended format as specified in FC-PH; the 12-bit port identifier represents the port number within the switch. Port Speed The desired baud rate for the port. It can have the values of 1GB(1), 2GB (2) or Auto-Negotiate (3). Name Server Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Name Server. This view provides the following information. Index The Name Server database entry. Port ID The Fibre Channel port address. Port Type The type of port. N_Port, NL_Port, etc., for this entry. The type is defined in FC-GS-2. Port Name The Fibre Channel World_Wide Name of the port entry. Name Server Information View Port Symbol The contents of a Symbolic Name of the port entry. In FC- GS-2, a Symbolic Name consists of a byte array of 1 through 256 bytes, and the first byte of the array specifies the length of its contents. This variable corresponds to the 'contents of the Symbolic Name, without the first byte. Node Name The Fibre Channel World_Wide Name of the associated node as defined in FC-GS-2. Node Symbol The contents of a Symbolic Name of the node associated with the entry. In FC-GS-2, a Symbolic Name consists of a byte array of 1 through 256 bytes, and the first byte of the array specifies the length of its contents. This variable corresponds to the contents of the Symbolic Name, without the first byte (specifying the length). IPA The Initial Process Associator of the node for the entry as defined in FC-GS-2. IP Address The IP address of the node for the entry as defined in FC-GS- 2. The format of the address is in IPv6. COS The class of services supported by the port. The value is a bit-map defined as follows: 0 is class F, 1 is class 1, and 2 is class 2 etc. Device Management Page 24 Brocade SilkWorm Switches

25 Switching Information FC-4s The FC-4s supported by the port as defined in FC-GS-2. IP Nx_Port IpAddress of the Nx_port for the entry. World Wide Name The World Wide Name (WWN) of the Fx_port for the entry. Hard Address The 24-bit hard address of the node for the entry. FW Thresholds Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > FW Thresholds. This view provides the following information. Index An entry for each threshold in this table. Status Identifies if a threshold is enabled or disabled Name The name of the threshold. Label Label of the threshold. FW Thresholds Information View Current Val A current counter of the threshold. Last Event The last event type of the threshold. Last Event Time The last event value of the threshold. Last State The last event time of the threshold Behavior Type A behavior of which the thresholds generate events. Behavior Int An integer of which the thresholds generate continuous events. Device Management Page 25 Brocade SilkWorm Switches

26 Switching Information FW Class Area Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > FW Class. This view provides the following information. Class Area Index The class type. Write Thresh Vals Applies the value changes. Default Unit A Default unit string name for a threshold area. Default Timebase A Default timebase for the current threshold counter. Default Low A Default low threshold value. Default High A Default high threshold value. Default Buf Size A Default buffer size value. Cust Unit A custom unit string name for a threshold area. Cust Timebase A custom timebase for the current threshold counter. FW Class Area Information View Cust Low A custom low threshold value. Cust High A custom high threshold value. Cust Buf Size A custom buffer size value. Thresh Level A level where all the threshold values are set at. Write Act Vals SwFwis is set to apply act value changes. Default Changed Acts Default action matrix for changed event. Default Exceed Acts Default action matrix for exceeded event. Default Below Acts Default action matrix for below event. Default Above Acts Default action matrix for above event. Default In Between Acts Default action matrix for in-between event. Cust Changed Acts Custom action matrix for changed event. Device Management Page 26 Brocade SilkWorm Switches

27 Switching Information Cust Exceeded Acts Custom action matrix for exceeded event. Cust Below Acts Custom action matrix for below event. Cust Above Acts Custom action matrix for above event. Cust in Between Acts Custom action matrix for in-between event. Valid Acts Matrix of valid acts for an class/area Act Level A level where all the actions are set. Event Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Events. This view provides the following information. Number of Entries The number of entries in the Event Table. Event Index The event entry. Event Time Info The date and time when this event occurred, in textual format. Event Level The severity level of this event entry. Event Information View Event Repeat Count How many times this particular event has occurred. Event Descr The textual description of the event. End Devices RLS Information View Access: From the Icon Subviews menu for the Device icon, select Switching Information > End Devices. This view provides the following information. Port The port number of the end device. Alpa The alpa of the end device. Post ID The Fibre Channel port address. Link Fail Count Link failure count for the end device. Sync Loss Count Sync loss count for the end device. Device Management Page 27 Brocade SilkWorm Switches

28 Switching Information Sig Loss Count Sig loss count for the end device. Proto Error Count Protocol error count for the end device. Invalid Word Count Invalid word count for the end device. Invalid CRC Count Invalid CRC count for the end device. Bloom Performance Alpa Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Bloom Perf Alpa. This view provides the following information. Alpa Port The port index of the switch. Alpa Index The ALPA index. There can be 126 ALPA values. Alpa The ALPA values. These values range between x01 and x'ef(1 to 239). ALPA value x'00' is reserved for FL_Port If Alpa device is invalid, then it will have -1 value. Bloom Performance Alpa Information View Alpa CRC Count Get CRC count for given ALPA and port. This monitoring provides information on the number of CRC errors occurred on the frames destined to each possible ALPA attached to a specific port. Bloom Performance End to End Performance View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Bloom Perf EE. The view provides the following information. EE Port The port number of the switch. EE Ref Key The reference number of the counter. This reference is assigned when a filter is created. EE CRC End to End CRC error for the frames that matched the SID- DID pair. EE FCW Rx End to End count of Fibre Channel words (FCW), received by the port, that matched the SID-DID pair. EE FCW Tx End to End count of Fibre Channel words (FCW), transmitted by the port, that matched the SID-DID pair. Device Management Page 28 Brocade SilkWorm Switches

29 Switching Information Bloom Performance Filter Base Information View EE SID SID info by reference number. SID (Source Identifier) is a 3- byte field in the frame header used to indicate the address identifier of the N-Port from which the frame was sent. EE DID DID info by reference number. DID (Destination Identifier) is a 3-byte field in the frame header used to indicate the address identifier of the N-Port to which the frame was sent. Bloom Performance Filter Base Information View Access: From the Icon Subviews menu Device icon, select Switching Information > Bloom Perf Filter. This view provides the following information. Filter Port The port number of the switch. Filter Ref Key The reference number of the filter. This reference is assigned when a filter is created. In SNMP, Index starts at one instead of 0. Add one to actual ref key. Filter Count Statistics of filter based monitor. Filter based monitoring provides information about a filter hit count such as Read command, SCSI, IP traffic, and SCSI Read/Write Filter Alias The trunking status of the switch - whether the switch supports the trunking feature or not. Trunking Information View Access: From the Icon Subviews menu for the Device icon, select Switch Information > Trunking. Trunk Port Index The switch port index. Note that the value of a port index is 1 higher than the port number labeled on the front panel. Trunk Group Number A logical entity which specifies the Group Number to which the port belongs to. If this value is 0 it means the port is not Trunked. Trunk Master Port number that is the trunk master of the group. The trunk master implicitly defines the group. All ports with the same master are considered to be part of the same group. Port Trunked The current state of trunking for a member port. Device Management Page 29 Brocade SilkWorm Switches

30 Switching Information Trunk Group Information Trunk Group Information Access: From the Icon Subviews menu for the Device icon, select Switch Information > Trunking Group. Trunk Group Number A logical entity which specifies the Group Number to which port the belongs. Trunk Group Master The master port id for the TrunkGroup. Trunk Group Tx The aggregate value of the transmitted words by this TrunkGroup. Trunk Group Rx The aggregate value of the received words by this TrunkGroup. Device Management Page 30 Brocade SilkWorm Switches

31 Application Views This section describes the main Application view and the associated application-specific subviews available for models of Brocade SilkWorm Switch devices in SPECTRUM. Access: From the Icon Subviews menu for the Device icon, select Application. Figure 7: Main Application View Main Application View When a device model is created, SPECTRUM automatically creates models for each of the major and minor applications supported by the device. The main Application view identifies all of these application models, shows their current condition status, and provides access to application-specific subviews. Figure 7 shows this view in the Icon mode. If you prefer the List mode, which displays applications as text labels, select View > Mode > List. For more information on this view, refer to the MIBs and the Application View document. SpectroGRAPH: Application: Model Name File View Tools Bookmarks Model Name Contact Description Location Network Address System Up Time Manufacturer Device Type Serial Number Model Name Model 6E132_25 Type Help Model Name of type <model type> of Landscape node: Primary Device Management Page 31 Brocade SilkWorm Switches

32 Application Views Supported Applications SPECTRUM s applications can be grouped within two general categories as follows: Applications associated with non proprietary. Device-Specifc Applications. Common Applications For the most part, these applications represent the non proprietary MIBs supported by devices. Listed below (beneath the title of the SPECTRUM document that describes them) are some of the common applications currently supported by SPECTRUM. Refer to these documents when your devices support these applications. Note: Routing Applications - Generic Routing - Repeater - AppleTalk - DECnet - OSPF - OSPF2 The documents listed below (in bold font) are available for viewing at: /secure/products/spectrum_doc/ - BGP4 - VRRP - RFC 2932 Bridging Applications - Ethernet Special Database - Spanning Tree - Static - Transparent - PPP Bridging - Source Routing - Translation - QBridge MIB II Applications - SNMP - IP - ICMP - TCP - System2 - UDP Transmission Applications - FDDI - Point to Point - DS1 - DS3 - RS WAN Supported Applications Device Management Page 32 Brocade SilkWorm Switches

33 Application Views - Frame Relay - Token Ring - Ethernet - Fast Ethernet - RFC 1317App - RFC 1285App - RFC 1315App App - SONET Technology Applications - APPN - ATM Client - DHCP - DLSw - PNNI - RFC 1316App - RFC RFC RFC RFC 2925 DOCSIS Applications - DOCSISCblDvApp - DOCSISQOSApp - DOCSISBPI2App - DOCSISBPIApp - DOCSISIFApp Supported Applications Digital Subscriber Line (DSL) Applications - ADSL Device-Specific MIBs SPECTRUM imports the following device-level proprietary MIBs into its database: SW-Mib These MIBs can be used in conjunction with SPECTRUM s optional customization products (referred to as the Level I Tool Kits) to create application models and views that display the condition of selected MIB objects. Note: Aprisma Management Technologies can provide training, technical assistance, and custom engineering support services for creating application models and their associated views. There are no device-specific applications supported for the Brocade SilkWorm Switches at this point. Device Management Page 33 Brocade SilkWorm Switches

34 Performance Views This section introduces the Performance view. For details concerning this view, refer to the SPECTRUM Views documentation. Performance views display performance statistics in terms of a set of transmission attributes, e.g., cell rates, frame rates,% error, etc. A typical view is shown in Figure 8. The instantaneous condition of each transmission attribute is recorded in a graph. The statistical information for each attribute is presented in the adjacent table. Generally, you determine performance at the device level through Performance views accessed from the Device and Application icons. You determine performance at the port/interface level through Performance views accessed from Interface icons. Figure 8: Performance View SpectroGRAPH: Type Routing File View Tools Bookmarks Model Name Contact Description Location Network Address Primary Application System Up Time Manufacturer Device Type Serial Number Value Average Peak Value Log * Frame Rate % Delivered % Forwarded % Transmit % Error % Discarded 0:40:0 0:30:0 0:20:0 0 *Frames per second Graph Properties Scroll to Date-Time Detail type routing of type IP Routing of Landscape node: Primary Device Management Page 34 Brocade SilkWorm Switches

35 Configuration Views This section describes the various Configuration views available for models of the Brocade SilkWorm Switch devices in SPECTRUM. Configuration views let you see and modify current settings for the modeled device and its interfaces, ports, and applications. The following Configuration views are available for models of Brocade SilkWorm Switch devices: Figure 9: Device Configuration View SpectroGRAPH: Model Name File View Tools Bookmarks Help Device Configuration View (Page 36) Device Configuration View Model Name Description Location Contact Manufacturer Sys Up Time Configuration View Net Address Device Type Serial Number Access: From the Icon Subviews menu for the Device icon, select Configuration. A typical Device Configuration view is shown in Figure 9. Generally, this view includes a few fields that display device information as well as an Interface Configuration Table that lists interface parameters, some of which can be changed (see SPECTRUM Views). Some Device Configuration views include one or more buttons that provide access to devicespecific configuration information. These are described below.. Contact Status Number of Interfaces Interface Address Table Sort Find Update Interface Configuration Table Index Description Type Bandwidth Physical Addre IP Address of type Model of Landsape: Primary Device Management Page 35 Brocade SilkWorm Switches

36 Configuration Views Device Configuration View IF Address Translation Refer to the SPECTRUM Views documentation. Device Management Page 36 Brocade SilkWorm Switches

37 Model Information View This section provides a brief overview of the Model Information view. Model Information views display administrative information about devices and their applications and let you set thresholds and alarm severity for the devices. Figure 10 shows a sample Model Information view. The layout of this view is the same for all model types in SPECTRUM but some information will vary depending on the model it defines. Refer to the SPECTRUM Views documentation for a complete description of this view. Model Name Description Location Figure 10: Model Information View SpectroGRAPH: Model Name File View Tools Bookmarks Contact Manufacturer SysUpTime Model Information View Net Address Device Type Serial Number Help MM Name MM Part Number MM Version Number Model Type Model Creation Time Model Created By Model State Security String DCM TimeOut DCM Retry Poll Interval Poll Status Log Ratio Last Successful Poll True General Information Condition Condition Value Contact Status Lost Child Count Value When Yellow Value When Orange Value When Red Communication Information Poll / Log Information Logged Community Name Mgnmt Protocol Polled IP Address of Model Type of Landscape: Primary Device Management Page 37 Brocade SilkWorm Switches

38 Traps, Events, and Alarms This section provides you with an overview of trap, event, and alarm support. This section describes any device-specific events and alarms supported by the Brocade SilkWorm Switches (SM- BRC1000) management module. Standard Trap Support Device-Specific Trap Support Device-Specific Trap Support The supported device-specific traps are listed in Table 10 (Page 40). Standard Trap Support The following standard traps are supported. Table 9: Standard Trap Support Standard Trap Name OID coldstart 0.0 warmstart 1.0 linkdown 2.0 linkup 3.0 authenticationfailure 4.0 egpneighborloss 5.0 Device Management Page 38 Brocade SilkWorm Switches

39 Traps, Events, and Alarms Device-Specific Trap Support Table 10: BROCADE-SW-TRAP-MIB Traps Trap Name OID Variable Bindings Event Generated Alarm Generated Alarm Severity swfault (Page 41) x043b0001 0x043b0001 Red swsensorscn (Page 41) swscportscn (Page 41) sweventtrap (Page 41) x043b0002 0x043b0002 Yellow 0x043b0003 0x043b0003 Yellow 0x043b0004 0x043b0004 Yellow swfabricwatchtrap (Page 41) swtrackchangestrap (Page 41) x043b0005 0x043b0005 Yellow x043b0006 0x043b0006 Yellow Device Management Page 39 Brocade SilkWorm Switches

40 Traps, Events, and Alarms Proprietary Trap Descriptions swfault A swfault(1) is generated whenever the diagnostics detect a fault with the switch. swsensorscn A swsensorscn(2) is generated whenever an environment sensor changes its operational state, for example a fan stops working. The VarBind in the Trap Data Unit shall contain the corresponding instance of the sensor status, sensor index, sensor type, sensor value (reading) and sensor information. Note that the sensor information contains the type of sensor and its number in textual format. swscportscn A swfcportscn(3) is generated whenever an FC_Port changes its operational state. For example, the FC_Port goes from on-line to offline. The VarBind in the Trap Data Unit shall contain the corresponding instance of the FC_Port's operational status and index. sweventtrap This trap is generated when an event with a level at or below sweventtraplevel occurs. swfabricwatchtrap This is the trap to be sent by Fabric Watch to indicate that an event has occurred. Device-Specific Trap Support swtrackchangestrap This is the trap to be sent for tracking login/logout/config changes. Device Management Page 40 Brocade SilkWorm Switches

41 Traps, Events, and Alarms Device-Specific Trap Support Device Management Page 41 Brocade SilkWorm Switches

42 Index A Address Interface IP 13 Physical (MAC) 13 Translation 14 Admin Status 12 Agent Trap Recipient 21 Alarm Generated 40 Alpa 28 Alpa CRC Count 29 Applications 32 B Baud Rate 21 Beacon 19 Behavior Int 26 Behavior Type 26 Boot Prom 18 C Component Detail, fibre channel port 9 Configuration Device 36 COS 25 Cust Timebase 27 D DevTop Views 15 Documentation 5 Domain ID 20 E Event Generated 40 F FC-4s 25 Fibre channel port interface 9 Filter Alias 30 Filter Count 30 Firmware 18 FLASH 18 H Hard Address 26 Hardware 6 I Icons Device 7 Interface 12 Interface Type, Device 12 IP Address 25 IPA 25 L Lips Ins 24 Lips Last Alpa 24 Lips Outs 24 Device Management Page 42 Brocade Silkworm Switches

43 Index Index M Management Tasks 8 Mask 14 Model Information 38 Types of 6 N Neighbor Table 20 Network I/O ports 15 Network Type 13 Node Symbol 25 O OID 40 P Password 19 Performance Statistics 35 Port Capacity 21 Port Number, Device 12 Port Symbol 25 Port Table 21 Port Trunked 31 POST Result 19 Principal Switch 20 R Remote Domain 20 RX C2 23 RX C2 Frames 23 RX C3 23 RX LCs 23 RX Words 23 S Sensor Table 19 Serial ports 15 Statistics Routing Frame Transmission 35 T Telnet Admin Status 17 Threshold Information 13 Track Changes String 17 Trap Name 40 Trap Support 39 Troubleshooting 8 Trunk Group Number 31 Trunk Group Rx 31 Trunk Master 31 Trunk Port 30 TX Frames 23 TX Type 23 TX Words 23 V Valid Acts 28 W World Wide Name 24 Write Thresh Vals 27 Device Management Page 43 Brocade Silkworm Switches