for Hardware Installation: IG550 Integrated Gateway

Transcription

1 Quick Start for Hardware Installation: IG550 Integrated Gateway Preparing before you go on-site Getting ready on-site Upgrading J-series router software, if necessary... Verifying the router has the power for the TIMs and PIMs Installing hardware Loading Disk on Key, if available Connecting the LAN and your laptop after using Disk on Key Finish configuring the router after using Disk on Key Installing an IG550 Integrated Gateway using the J-Web Quick Configuration interface Configuring the router using the CLI, if you did not use J-Web Quick Configuration Configuring the TGM Issue January 008

2

3 Preparing before you go on-site. Check Juniper software compatibility with TGM550 Gateway Module firmware. See Download the most recent firmware for the TGM550. See support.avaya.com.. Ensure the customer has an FTP or TFTP server that is accessible to the TGM550. If not, download a TFTP server to your laptop.. Review safety requirements and airflow requirements. See Installing and Configuring the IG550 Integrated Gateway. 5. Get the tools you need: Electrostatic discharge (ESD) grounding strap Flathead and Phillips head screwdrivers Getting ready on-site. Verify you have: The Juniper Services Router (J0, J50, J50 or J650) A 0 AWG grounding cable An AC or AWG DC power cable Cables for the TGM550, Telephony Interface Modules (TIMs), and Physical Interface Modules (PIMs)! CAUTION: CAUTION: You cannot use a AWG grounding cable with the router. The grounding cable must be 0 AWG. A USB modem Two distinct and different console cables: - An RJ-5 flat rollover cable and a DB-9 adapter for console connections to the TGM550 - An ordinary round RJ-5 Ethernet cable and a DB-9 adapter for console connections to the Juniper router Issue January 008

4 Upgrading J-series router software, if necessary Note: Note: The software of the Juniper Services Router must match the firmware version of the TGM550. See the Communication Manager Software/Firmware Compatibility Matrix under Downloads on support.avaya.com.. See the Juniper J0, J50, J50, and J650 Services Router Getting Started Guide, Release 8.. Verifying the router has the power for the TIMs and PIMs Verify that the project manager, sales representative, or sales engineer has ordered the appropriate quantity and types of TIM and PIM modules for the router you are installing. If not, see "TIM and PIM limits based on heat and power used by the IG550" in Overview of the Avaya IG550 Integrated Gateway, Installing hardware. If the customer has a four-post rack and is using a shelf, install the shelf according to manufacturer guidelines. If the customer is using the Quick Start for Hardware Installation: IG550 Integrated Gateway

5 NETWORKS Gateway ASB RST TGM550 Console ETR Trunk Line Analog TIM5 Line 5 6 Line 7 8 E/T TST SIG TIM50 SO EI SM EM SI EO STATUS ALARM HA TX/RX LINK TX/RX LINK TX/RX LINK TX/RX LINK 0/0 0/ 0/ 0/ 0/00/000 NETWORKS BRI TIM5 0 5 CONSOLE AUX USB Gateway ASB RST TGM550 Console ETR Trunk Line Analog TIM5 Line 5 6 Line 7 8 E/T TST SIG TIM50 SO EI SM EM SI EO STATUS ALARM HA RESET CONFIG TX/RX LINK TX/RX LINK TX/RX LINK TX/RX LINK 0/0 0/ 0/ 0/ 0/00/000 6 J50 BRI TIM5 0 5 J50 6 CONSOLE AUX USB brackets supplied with the router, install the brackets on the chassis of the Juniper Services router midway between the front and back. Juniper RESET CONFIG qsmabrkt LAO Install the router on the rack. Juniper qsmarack LAO Be sure the power to the router is off. Issue January 008 5

6 Gateway Analog E/T TIM50 ETR STATUS ALARM HA Trunk Line Line TX/RX LINK TX/RX LINK TX/RX LINK TX/RX LINK 0/0 0/ 0/ 0/ 0/00/000 TIM5 CONSOLE AUX USB 0 5 CAUTION:! CAUTION: The Juniper Services Router must be turned off before inserting or removing the Avaya TGM550, TIM modules, or PIM modules. These modules are not hot-swappable. If you attempt to remove or insert these modules while the router is turned on, the router might reset or malfunction in some other way.. Insert the TGM550 and each TIM, PIM, epim, or upim into the correct slot. If the slots are already administered on the Communication Manager server, the slots you use must match the Communication Manager administration. The TGM550, TIMS, and upims can be inserted into any slots. Other PIMs and epims might have limitations. See "Inserting the TGM550, the TIMs, and the PIMs in the router, if necessary" in Installing and Configuring the Avaya IG550 Integrated Gateway, Align the notches in the connector at the rear of the TGM550, TIM, or PIM with the notches in the slot in the router. Then slide the module in until it lodges firmly in the router. CAUTION:! CAUTION: Carefully slide the module straight into the slot to avoid damaging the connector components. Line Juniper NETWORKS TST TGM550 Console SIG RST ASB TIM5 5 6 Line 7 8 SO EI SM EM SI EO RESET CONFIG BRI 6 J50 6. Cable the TIMs and PIMs. TGM550 CAT5 harness cables with RJ connectors TIM508 A B5A unshielded 5-pair amphenol cable 6 Quick Start for Hardware Installation: IG550 Integrated Gateway hmacrdr LAO 0006

7 TIM50 T/E H600-8 Group T cable with an RJ8C connector TIM5 CAT5 cable with an RJ connector TIM56 A B5A unshielded 5-pair amphenol cable TIM58 A B5A unshielded 5-pair amphenol cable TIM5 CAT5 cable with an RJ5 connector Juniper PIMs, EPIMs, and UPIMs see Juniper J0, J50, J50, and J650 Services Router Getting Started Guide, Release For the TIM508, TIM56, or TIM58, use the screw at the end of the Amphenol connector to attach the connector to the left side of the TIM s Amphenol receptacle. Use a tie wrap to attach the cable to the tie wrap loop to the right of the Amphenol receptacle on the TIM. 8. Connect the grounding cable to earth ground and the chassis grounding point. Specifications include: 0 AWG Minimum 8 Amps amperage Ring-type, vinyl-insulated TV-6R lug or equivalent to accommodate the 0 AWG cable J50 or J650 ground - J0 or J50 ground - qsmagnd LAO Issue January 008 7

8 9. Connect power to the back of the router. AC Power a. Insert the appliance coupler end of a power cord into the appliance inlet on the power supply faceplate. b. For a 650 only, repeat for the second power supply. c. Insert the plug of each cord into an AC power source receptacle. DC Power a. Ensure that the voltage across the DC power source cable leads is 0 V and that there is no chance that the cable leads might become active during installation. b. Verify that a licensed electrician has attached the appropriate power cable lugs to the ends of the negative and positive DC source power cables. These are the lugs that you are attaching to the chassis DC terminals. J50 J650 qsmagnd LAO Quick Start for Hardware Installation: IG550 Integrated Gateway

9 Gateway ASB RST TGM550 Console Analog Line E/T SIG TIM50 ALARM STATUS HA Trunk Line TX/RX LINK TX/RX LINK TX/RX LINK TX/RX LINK 0/0 0/ 0/ 0/ 0/00/000 TIM5 CONSOLE AUX USB 0 5 Loading Disk on Key, if available Note: Note: This Disk on Key procedure assumes that the router currently has the factory default settings without a configuration file. If there is a configuration file, this procedure cannot work. However, if you want to use a USB disk on key and the router already has been configured, you can press on the recessed configuration button for over 5 seconds to delete the configuration file or login to the router console port and issue commands to set the router to the factory default settings.. If available, insert the Disk on Key (USB memory stick) into the USB port on the front of the router. The Disk on Key contains the configuration information. If a Disk on Key is not provided, go to Configuring the router using the CLI, if you did not use J-Web Quick Configuration on page. TST ETR TIM5 Line SO EI SM EM SI EO RESET CONFIG BRI 6 J50 qsmausbk LAO Press the power button (see in the appropriate illustration that follows) to turn on the Juniper Services Router. Issue January 008 9

10 J50/J650 J0 J50. When the Power on LED lights steady green, remove the Disk on Key. The configuration file has been downloaded, loaded, and committed. The root password is also set as part of the configuration. 0 Quick Start for Hardware Installation: IG550 Integrated Gateway

11 ASB RST ETR Analog Line E/T TST SIG TIM50 STATUS ALARM HA Trunk 0/00/000 LINK TX/RX Line Gateway ASB RST TGM550 Console Analog Line E/T SIG TIM50 BRI 0 ALARM STATUS HA 5 6 J50 Trunk Line CONSOLE AUX USB 0 5 Connecting the LAN and your laptop after using Disk on Key. With an RJ-5 Ethernet cable, cable an Ethernet port (Eth 0) of the Juniper Services Router. Juniper NETWORKS TST ETR TIM5 Line SO EI SM EM SI EO RESET CONFIG TX/RX LINK TX/RX LINK TX/RX LINK TX/RX LINK 0/0 0/ 0/ 0/ 0/00/000 BRI TIM5 6 J50 qsmalape LAO Connect your PC or laptop to the console port of the Juniper Services Router. Juniper NETWORKS Gateway TGM550 Console TIM5 5 6 Line 7 8 SO EI SM EM SI EO RESET CONFIG TX/RX LINK TX/RX LINK TX/RX LINK 0/0 0/ 0/ 0/ TIM5 5 CONSOLE AUX USB qsmalapa LAO Issue January 008

12 . Configure your laptop: Turn on the power to the management device. Start your asynchronous terminal emulation application (such as Microsoft Windows Hyperterminal) and select the appropriate COM port to use (for example, COM). Configure the port settings as follows: - Bits per second: Data bits: 8 - Parity: None - Stop bits: - Flow control: None Finish configuring the router after using Disk on Key. Connect the USB modem to one of the USB ports.. Upgrade the JUNOS software on the router, if necessary. See Juniper J-Series Services Router documentation.. Go to Configuring the TGM550 on page 7. Installing an IG550 Integrated Gateway using the J-Web Quick Configuration interface You can use the J-Web Quick Configuration interface to install both a Juniper J-Series Router and an IG500 gateway. For more information see "Installing an IG550 Integrated Gateway with the J-Web Quick Configuration interface" in Installing and Configuring the Avaya IG550 Integrated Gateway, Quick Start for Hardware Installation: IG550 Integrated Gateway

13 ASB RST ETR Analog Line E/T TST SIG TIM50 STATUS ALARM HA Trunk 0/00/000 LINK TX/RX Line Gateway ASB RST TGM550 Console Analog Line E/T SIG TIM50 BRI 0 ALARM STATUS HA 5 6 J50 Trunk Line CONSOLE AUX USB 0 5 Configuring the router using the CLI, if you did not use J-Web Quick Configuration. With an RJ-5 Ethernet cable, cable an Ethernet port of the Juniper Services Router. Juniper NETWORKS TST ETR TIM5 Line SO EI SM EM SI EO RESET CONFIG TX/RX LINK TX/RX LINK TX/RX LINK TX/RX LINK 0/0 0/ 0/ 0/ 0/00/000 BRI TIM5 6 J50 qsmalape LAO Connect your PC or laptop to the console port of the Juniper Services Router. Juniper NETWORKS Gateway TGM550 Console TIM5 5 6 Line 7 8 SO EI SM EM SI EO RESET CONFIG TX/RX LINK TX/RX LINK TX/RX LINK 0/0 0/ 0/ 0/ TIM5 5 CONSOLE AUX USB qsmalapa LAO Issue January 008

14 . Configure your laptop: Turn on the power to the management device. Start your asynchronous terminal emulation application (such as Microsoft Windows Hyperterminal) and select the appropriate COM port to use (for example, COM). Configure the port settings as follows: - Bits per second: Data bits: 8 - Parity: None - Stop bits: - Flow control: None. Log in to the router with the root login and password. If a password has not been established, leave the password field blank. 5. At the root prompt (%), enter cli. 6. At the cli prompt (>), enter configure. 7. At the configure prompt (#), enter the following: If a root password has not already been set, set system root-authentication plain-text-password, and a new password at the prompt, which you must enter twice. set system time-zone <time-zone> where <time-zone> is the name of the name of the time zone, identified by continent and city. Use the? option to see the list of time zones. set system host-name <host-name> where <host-name> is the name of the Juniper Services Router to be accessed on the LAN/WAN. set interfaces ge-0/0/<#> unit 0 family inet address <IP_address>/ where <#> is the Gigabit port number (0,,, or ) you want, <IP_address> is the address of the router, and / is the subnet mask. The subnet mask may vary, depending on the customer s configuration. Quick Start for Hardware Installation: IG550 Integrated Gateway

15 Note: Note: The ge-0/0/0 port number is often reserved for services access. set interfaces vp-<slot_number>/0/0 unit 0 family inet address <internal_ip_address>/ destination <tgm550_ip_address>, where <internal_ip_address> is the address the TGM550 uses to telnet to the router and <tgm550_ip_address> is the IP address for accessing the TGM550. set system name-server <IP_address> where <IP_address> is the address of a DNS server on the LAN/ WAN. Repeat this command for any additional DNS servers the TGM550 might access. set system services ssh root-login allow to allow access to the router with ssh. This command is optional, based on customer requirements. set system services telnet to allow access to the router with telnet. This command is optional, based on customer requirements. set system domain-search <domain_name> where <domain-name> is the name of the Juniper Services Router s network or subnetwork. Repeat this command for any additional domains the TGM550 might access. set system domain-name <domain_name> where <domain-name> is the name of the Juniper Services Router s domain. set system ntp server <IP_address> where <IP_address> is the address of an NTP server for time synchronization. set interface lo0 unit 0 family inet address <IP_address> where <IP_address> is the loopback address of the Juniper Services Router. Issue January 008 5

16 set system login user <user_name> class super-user where <user_name> is the user login to the router from TGM550. This command is completed based on customer requirements. Complete the password prompts. set system login user <user_name> authentication plain-text-password. At the two password prompts, enter the password.! CAUTION: CAUTION: If a root password has not been set, you must set a new password before you commit the configuration. Check with your Project Manager to get the password. 8. At the prompt, type commit. The system may take some time to commit the commands and reset. 9. Configure the MGC list. a. At the configure prompt (#), enter exit. b. At the cli prompt (>), enter set tgm fpc <slot_number> media-gateway-controller [<IP_address> <IP_address> <IP_address> <IP_address>] where <slot_number> is the location of the TGM550, <IP_address> is either the Processor Ethernet IP address of the primary server (S800, S800, or S8500) or an IP address to a C-LAN connected to the primary server (S800, S8500, or S8700-series). The additional IP addresses are the addresses for additional C-LANs or Local Survivable Processors (S800 or S8500). 0. Set the WAN interface. See Juniper J-Series Services Router Getting Started Guide. See J-Series Services Router Basic LAN and WAN Access Configuration Guide.. Set routing options using static routes, OSPF, RIP, BGP, or IS-IS protocols. See J-Series Services Router Basic LAN and WAN Access Configuration Guide.. Connect the USB modem to one of the USB ports.. Configure the USB modem. See Installing and Configuring the IG550 Integrated Gateway, Quick Start for Hardware Installation: IG550 Integrated Gateway

17 . Upgrade the JUNOS software on the router, if necessary. See Juniper J-Series Services Router documentation. 5. Go to Configuring the TGM550 on page 7. Configuring the TGM550. Log in to the TGM550. At the cli prompt (>), type ssh where <login> is root or another login, if previously administered, and <ip_address> is the IP address of the TGM550, and press Enter. The message, Are you sure you want to continue connecting? appears. Enter yes. At the password prompt, type the password and press Enter. Get this password from either your project manager or your services support group. You are now logged-in. - If you are prompted to change the root password, change the password to a password agreed upon with the customer administrator.. Identify the TGM550 serial number. At the TGM550 command line, type show system. Note the serial number of the TGM550.. At the TGM550 command line, type show recovery and check the transition points for the mgc list.. Ping the Communication Manager server. At the TGM550 command line prompt, type ping <ip_address>, where <ip_address> is the ip address of the server. Verify that replies from the server scroll down the screen. 5. Update TGM550 firmware. Issue January 008 7

18 At the TGM550-00<super># prompt, type show boot bank to determine the non-active disk partition (bank). You copy the firmware to the non-active boot bank. At the TGM550-00<super># prompt, type one of the following commands, depending on whether the file resides on an FTP, or TFTP server: - copy [tftp or ftp] SW_image <bank> <filename> <server_ip_address> where <bank> is the bank that is the non-active boot bank, <filename> is the full path name of the firmware image file, which begins and will be similar to the name tgm550_sw_6_6_0.bin, and <server_ip_address> is the IP address of the FTP or TFTP server. For an FTP server, enter the login and password, if prompted. Logout of the tftp or ftp server. At the TGM550 command line, enter show download software status 0 and check the status of the download. At the TGM550 command line, type set boot bank bank-<bank> where <bank> is the same letter you entered in the previous step. Enter copy running-config start-config. Type exit to return to the Juniper Services Router CLI. Enter request chassis fpc restart slot <slot_number> to reset the TGM550 where <slot_number> is the slot of the TGM550. Log in to the TGM550 again. At the TGM550-00<super># prompt, type show mg list_config. Verify the system the list of software. 6. Check the authentication file ID (Avaya personnel only). At the TGM550 command line prompt, type show auth-file info. In the AF ID field, record the 0-digit AF ID, for example, Register the password (authentication) file with the ART tool (Avaya personnel only) or with the appropriate customer care center (business partners only). 8 Quick Start for Hardware Installation: IG550 Integrated Gateway