SPECIAL SPECIFICATION 6192 Hardened Ethernet Switch

Size: px

Start display at page:

Download "SPECIAL SPECIFICATION 6192 Hardened Ethernet Switch"

Lindsey Nichols
5 years ago
Views:

1 2004 Specifications CSJ SPECIAL SPECIFICATION 6192 Hardened Ethernet Switch 1. Description. This Item governs the furnishing and installation of Hardened Ethernet Switch (HES) at designated locations as shown on the plans, as detailed in accordance with these specifications, and as directed by the Engineer. 2. Materials. A. General Requirements. Provide all HES of the same manufacturer. Provide all new equipment in strict accordance with the details shown on the plans and in the specifications. Provide a high-performance and hardened Ethernet switch supporting standard OSI Layer 2 and 3 functionality. Provide a HES that supports direct connectivity to existing networks configured in ring and mesh fault tolerant topologies enabling applications to operate reliably, and with low latency. Include all equipment licenses, where required, for any software or hardware in the system. B. Adherence to Standards. Comply with the following standards for all HES furnished, assembled, fabricated, or installed under this item: 1. IEEE 802.1d: Spanning Tree Protocol 2. IEEE 802.1p: Class of Services 3. IEEE 802.1q: VLAN Tagging 4. IEEE 802.1w: Rapid Spanning Tree Protocol 5. IEEE 802.3: 10BASE-T 6. IEEE 802.3d: MAC Bridges 7. IEEE 802.3u: 100BASE-TX, 100BASE-FX. 8. IEEE 802.3x: Flow Control 9. RFC768: UDP 10. RFC783: TFTP 11. RFC791: IP

2 3. Equipment. 12. RFC792:ICMP 13. RFC793: TCP 14. RFC826: ARP 15. RFC854: Telnet 16. RFC894: IP over Ethernet: 17. RFC1112: IGMP v1 18. RFC1493: Bridge MIB 19. RFC1519: CIDR 20. RFC1541: DHCP (client) 21. RFC1907: SNMP v2 MIB 22. RFC2012: TCP MIB 23. RFC2013: UDP MIB 24. RFC2030: SNTP 25. RFC2068: HTTP 26. RFC2236: IGMP v2 27. RFC2578: SNMP v2 SMI 28. RFC2579: SNMP v2 TC 29. RFC2819: RMON MIB 30. RFC2863: IF MIB 31. UL, cul, FCC and CE. A. Functional Requirements. 1. Physical Design Requirements. Supply all HES with a physical design that conforms to the following requirements: a. Type A: Provide a minimum of two built-in 100 MB full-duplex switched single-mode fiber ports as indicated on the plans. Type B: Provide a minimum of three built-in 100 MB full-duplex switched single-mode fiber ports as indicated on the plans

3 b. Type A: Provide a minimum of two switched 10/100 MB copper (RJ 45) ports. Type B: Provide a minimum of six switched 10/100 MB copper (RJ 45) ports. c. Be configurable in point-to-point, daisy-chain, ring and mesh topologies for connectivity into new and existing fiber optic and copper based Ethernet networks. d. Type A: Provide a minimum of four EIA-232 DB9. e. Designed with an operating system that allows individual ports to be configured for port mirroring, speed, duplex, auto-negotiation, and flow control. Design the operating system to provide for broadcast storm frame filtering with user defined thresholds. f. Designed with an operating system allows for the collection of statistics on a per port basis and provides for full support of RMON statistics, history, alarms, and event groups. g. Designed with an operating system that provides port security to prevent unknown devices from gaining access to the network. In case of unauthorized attempts to access the network shutdown the port for a period of time along with SNMP trap and generate an alarm. h. Have high-strength 18-gauge galvanized steel enclosure to seal out insects, dirt, smoke, and other contaminants. i. Clearly identify all modules and assemblies with name, model number, serial number, or any other pertinent information required to facilitate equipment maintenance. 2. Electrical and Mechanical Requirements. Provide the following functionality and features: a. Ports Performance. (1) Provide Single-mode Fiber ports that operate at 100 Mbps with a Tx power of -2.5 dbm and a Rx sensitivity of -37 dbm yielding a typical link loss budget of (2) Provide RJ-45 ports that auto-negotiate operation at 10 Mbps and 100Mbps. b. Packet-Processing. (1) Filtering and forwarding rate from 100 Mbps ports: 148,800 pps max. (2) Filtering and forwarding rate from 10 Mbps ports: 14,880 pps max. (3) Processing type: store and forward

4 (4) Auto-learning: 8192 MAC address. (5) Frame buffer memory: 160 packet buffers, 1536 bytes each. (6) Switching Latency: < 5 microsecond (100Mbps). (7) Priority queues: 2. (8) VLANs: 1000 (9) IGMP multicast groups: 256. (10) Switching bandwidth: 1.6Gbps (11) Ring sizes: Up to 80 switches (12) Fault recovery time: < 5ms per switch 3. Network Connectors. a. Type A: Two RJ-45 connector, full/half duplex and 10/100 Mbps ports, independently auto-negotiating. Type B: Six RJ-45 connector, full/half duplex and 10/100 Mbps ports, independently auto-negotiating. b. Type A: Two dual SC connector, single-mode fiber, 100Mbps Type B: Three dual SC connector, single-mode fiber, 100Mbps full duplex ports. 4. Serial Connectors. Type A four DB9, EIA 232 connectors. 5. Mean Time Between Failure. > 10 years. 6. LED Indicators. One LED for power, three LEDs per port for link, Tx, and Rx activity. 7. Power Supply. a. AC power connector: Terminal block at rear of power supply chassis. b. Input Voltage: 85 to 264 VAC (auto-ranging). c. Input Frequency: 47 to 63 Hz (auto-ranging). d. Power Consumption: 20 watts (max). e. CSA/UL safety approved to +85 C. f. Fast Transient Protection: Compliant with IEEE C Mechanical

5 a. Enclosure: Rugged 18-gauge high-strength galvanized steel case with metal mounting plate included. Suitable for stand-alone, shelf, pedestal or wall mounting. Permanently and clearly identify the enclosure with name, model number, serial number, and any other pertinent information required to facilitate equipment maintenance. b. Dimensions: 3 in. H x 8 in. W x 10 in. D max. c. Weight: 5 lb. B. Power Requirements. Meet all of its specified requirements when the input power is 115 VAC ± 10%, 60 ± 3 Hz, for any Hardened Ethernet Switch furnished, assembled, fabricated, or installed under this Item. Do not allow the equipment operations to be affected by the transient voltages, surges and sags normally experienced on commercial power lines. It is the Contractor's responsibility to check the local power service to determine if any special design is needed for the equipment. Include the extra cost, if required, in the bid of this Item. C. Wiring. Meet all requirements of the National Electric Code for all wiring external to the HES switch. Cut all wires to proper length before assembly. Do not double back any wire take up slack. Neatly lace wires into cable with nylon lacing or plastic straps. Secure cables with clamps. Provide service loops at all connections. D. Transient Suppression. Provide diodes or other protective devices across the coils of all DC relays, solenoids and holding coils for transient suppression. E. Power Service Protection. Provide readily accessible, manually resettable or replaceable circuit protection devices (such as circuit breakers or fuses) for equipment and power source protection. Provide circuit breakers or fuses that are sized such that no wire, component, connector, PC board or assembly is subjected to sustained current in excess of their respective design limits upon the failure of any single circuit element of wiring. F. Fail Safe Provision. Design the equipment such that the failures of the equipment shall not cause the failure of any other unit of equipment. G. Connectors and Harnesses. Make external connections by means of connectors. Provide keyed connectors to preclude improper hookups. Color code and/or appropriately mark all wires to and from the connectors. Provide connecting harnesses of appropriate length and terminated with matching connectors for interconnection with the HES switches. Uniquely color code patch fibers with mixed connectors for easy identification. Plate all pins and mating connectors with not less than 20 microns of gold. Cover all connectors utilizing solder type connections with a piece of heat shrink tubing securely shrunk to insure that it protects the connection

6 H. Environmental Requirements. Meet all specified requirements during uncontrolled environmental operations characterized by an operating temperature range of -40ºC (- 40ºF) to +85ºC (185ºF) and a humidity range of 10% to 95% (non-condensing). I. Battery Backup System. Supply a battery backup system to provide a minimum of 2 hours of run time in the absence of power. For Ethernet switches installed in an air conditioned facility, provide a 0.5KVA Uninterruptible Power Supply in accordance with Special Specification, Uninterruptible Power Supply. For Ethernet switches installed in a non-environmentally controlled facility, provide a 0.5KVA field hardened battery backup system in accordance with Special Specification, Hardened Battery Backup System for Field Cabinets. 4. Contractor / Subcontractor Experience Requirements. Minimum requirements for the Contractor or designated subcontractors involved in the installation and testing of the Ethernet equipment are: A. Three years experience in the installation of Ethernet equipment. B. Two installed systems where Ethernet switches are installed and the system has been in continuously satisfactory operation for at least 2 years. Submit as proof, photographs or other supporting documents, and the names, addresses and telephone numbers of the operating personnel who can be contacted regarding the communication system. Necessary documentation of subcontractor qualifications must be provided by the Contractor prior to contract award. 5. Technical Assistance. Ensure that a manufacturer's technical representative is available on site to assist the Contractor's technical personnel at each installation site and with Ethernet equipment installation and communication system configuration. Do not execute the initial powering up of the ethernet equipment without the permission of the manufacturer's representative. 6. Construction. A. General. Utilize the latest available techniques with a minimum number of parts, subassemblies, circuits, cards, and modules to maximize standardization and commonality in the equipment design. Design the equipment for ease of maintenance, with all component parts being readily accessible for inspection and maintenance. Provide test points for checking essential voltages and waveforms. B. Electronic Components. Ensure that all electronic components comply with Special Specification, Electronic Components. C. Mechanical Components. Ensure that all external screws, nuts and locking washers are stainless steel. Do not use any self-tapping screws unless specifically approved by the Engineer

7 Make all parts out of corrosion resistant material, such as plastic, stainless steel, anodized aluminum or brass. Protect all materials used in construction from fungus growth and moisture deterioration. Separate dissimilar metals by an inert dielectric material. 7. Documentation Requirements. Provide Documentation in accordance with Special Specification, Testing, Training, Documentation, Final Acceptance and Warranty, Article Testing. Test each unit be in accordance with Special Specification, Testing, Training, Documentation, Final Acceptance and Warranty, Article Training. Provide training in accordance with Special Specification Item, Testing, Training, Documentation, Final Acceptance and Warranty, Article Warranty. Provide a written warranty in accordance with Special Specification, Testing, Training, Documentation, Final Acceptance and Warranty, Article Documentation. Provide documentation in accordance with Special Specification Testing, Training, Documentation, Final Acceptance and Warranty. 12. Final Acceptance. Final acceptance is provided in accordance with the Special Specification, Testing, Training, Documentation, Final Acceptance and Warranty. 13. Measurement. This Item will be measured as each unit furnished, installed, made fully functional and tested in accordance with these special specifications or as directed by the Engineer. 14. Payment. The work performed and materials furnished in accordance with this Item and measured as provided under Measurement will be paid for at the unit bid price for Hardened Ethernet Switch, of the type specified. This price includes all equipment described under this Item with all cables and connectors; all documentation and testing and also includes the cost of furnishing all labor, materials, software, warranty, training, equipment and incidentals

SPECIAL SPECIFICATION 8167 Ethernet Switch

2004 Specifications CSJ 0912-72-111 SPECIAL SPECIFICATION 8167 Ethernet Switch 1. Description. Furnish, install, integrate, and test Ethernet Switches (ES) and Hardened Ethernet Switches (HES) at designated