LCC1653/01, LRI1653/01 ActiLume DALI System

Transcription

1 1/8 Product description The Philips ActiLume lighting control system consists of a small, lightweight sensor and controller, designed for easy integration into luminaires. ActiLume is a true Plug and Play solution for open plan (up to 11 luminaires) or cell offices (e.g. 4 luminaires). It is used in a master/slave luminaire concept, easy to use and easy to install. Application brochures are available to help specify and apply the system in an optimal way. Features and benefits ActiLume DALI 15.8 Sensor LRI1653/01dimensions in mm Philips ActiLume is a DALI based lighting control system designed for maximum comfort and energy savings up to 75% (in fully automatic mode and when used in combination with Philips HF-Regulator Touch and DALI ballasts). ActiLume is a Plug & Play system; no specific lighting control training is needed. Moreover, the system is supported with simple, dedicated application and installation sheets. The ActiLume system consists out of three state-of-art miniature sensors combined with a controller containing a series of pre-programmed modes. The two most applied modes, cell and open plan offices, can be selected via a single push on the service button. The light sensor is sensitive for visible radiation (matching the human eye) providing automatic savings with daylight depending regulation, without any visible discomfort for the user. The movement detector is very sensitive to human movements and contains a 15 minutes delay to provide optimal functionality whilst maximizing energy saving during absence. Personal control solutions can be created by connecting a mains rated spring-back switch to the controller or by using an infrared remote control unit. In addition ActiLume offers the possibility to select so called comfort modes in line with the EN indoor lighting norm. These modes can be recalled by using a simple mode selection tool IRT9090/00. If needed further customization can easily be established by changing the factory settings with the mode selection tool IRT9090/00. The ActiLume controller contains two DALI outputs. These outputs are pre-programmed (factory setting) as a window and corridor row with a fixed light offset. The system can be extended with 1 or 2 additional movement detectors, LRM8118/00 and/or LRM8119/00 to maximize movement coverage. This respectively reduces the number of ballasts per controller to 10 or 9. Factory light level setting is at 600 lux at a reflection factor of Controller LCC1653/01, LCC1656/00 dimensions in mm

2 2/8 Applications The ActiLume system is designed for all office applications, from open plan to cell offices, lobbies or toilets, and from corridor to small meeting rooms. It offers dedicated modes, e.g. for schools, light-lines and direct/indirect lighting concepts. It even contains a specific comfort mode combining maximum energy savings and additional comfort based on a practical EN solution (mode 4, 5 or 9). Plug & Play control regimes Mode 1: Switching light off when the area is not occupied, saving maximum energy in a cell office situation. Mode 2: Maintaining a (lower) light level when the area is not occupied, avoiding dark areas in an open plan office. Next to the modes the following functions can be changed independently: - Power up behavior - Default light level - Background level Philips quality This ensures quality with respect to: System supplier As manufacturer of lamps, electronic control gear and lighting control equipment, Philips ensures that, from the earliest development stage, optimum performance is maintained. International standards Philips lighting control equipment complies with all relevant international rules and regulations. Technical data for installation Mains operation Rated mains voltage V Tolerances for performance -8% - +6% ( V) With tolerances for safety +/- 10% ( V) Mains frequency 50/60 Hz Input power (system) W Number of ballasts Number of extension sensors LRM8118/00 and/or LRM8119/ Technical data for design and mounting in fixtures Operating conditions Ambient temperature 0 ºC to 55 ºC Sensor and controller Rel. humidity 20% to 85%, no condensation T case Controller 75 ºC Sensor 55 ºC Storage conditions Temperature -25 ºC to +85 ºC Rel. humidity 10% to 95% (Non condensing) Sensor LRI1653/01 Connection RJ-10 4-Pole fixed to LRI1653/01, 100cm cable Compliances and approvals RFI 9kHz to 30MHz EN RFI 30MHz to 1000MHz EN A Immunity EN Safety EN EN Quality standard ISO 9001 Environmental standard ISO Approval marks ENEC CE marking RJ-10 (4P4C) Housing (casing) Material Polycarbonate UL94V-0 Glow wire test 850 C /5s Safety basic insulation 1500V When placed at a height of 3m the following values are valid: Infrared receiver Signal range r = 2.5 Light sensor Ambient light monitoring Monitoring 25 to 350 lux at sensor Monitoring area r = 2.5

3 3/8 Movement detector Detection area at 2.5m height: Large movement detection area Small movement detection area Passive Infra Red (PIR) 4x4m (sensitive for small movements) 6x5m (sensitive for large movements) Maximum height PIR: 3.5 m X-angle PIR: 82 Y-angle PIR: 100 Service button The service button can be used to: a. To select the user mode 1 and 2. The user mode can be toggled between mode 1 and 2 by means of a short push on the service button (<1 second). After button release the lamp will flash to indicate the selected user mode: 1 flash = User mode 1 (Cell office application) 2 flashes = User mode 2 (Open plan office application) More modes can be recalled by using the IRT9090/00. 6 m 4 m 4 m 5 m b. Adjust the factory set reference light level. Pressing the service button (>3 seconds) until the lamp gives a light flash (wink) will start the automatic calibration procedure. The light output of the luminaires connected to the window side (DALI 1) is set to 80%. The light output of the luminaires connected to the corridor side (DALI 2) is set to 100%. After 30 seconds the ActiLume controller is saving the actual light level as new reference light level (indicated by a second flash). This 30 seconds time delay is required to have sufficient time to step aside or remove a stepladder. Mounting The sensor has latching rills on the back so it can easily be mounted. It can also be mounted onto a lamp by means of a clip LCA8002/00 or LCA8003/00. There is an additional clip, LCA8005/00, for mounting the sensor in the luminaire housing. 60 mm R0-0.5 mm (4x) 1. Required Luminaires opening dimension: 60 x 22 (mm) 2. Thickness fitness of Luminaires fixture: 0.5~2.5 (mm) 22 mm Controller unit LCC1653/01 DALI Output In user mode 1 and user mode 2 the system is programmed as one channel. When enough daylight enters the room, the amount of artificial light will be automatically reduced and the DALI 2 output (corridor row) is programmed with a light offset of 30%. In other modes (which can be recalled with the IRT9090/00) ActiLume can use two channels depending the applications functionality. Mains switch By connecting a mains rated springback switch to connect Ls (Line-switched), dimming and switching on/off will be possible according the Touch and Dim functionality (Maximum 1 switch per controller). Switch to be connected to the controller! Remote control It is also possible to use remote control IRT8010/00, IRT8030/00 or IRT8050/00. The IRT8010/00 needs to be pointed to the sensor. The IRT8030/00 and IRT8050/00 have a X-Y-Z beam direction, making it suitable for wall mounting and table top use. Glow wire test 850 ºC / 5 s Safety, basic insulation 1500 V Material Polycarbonate UL94 V-0 Mounting The controller housing contains snap-in pins for quick fixation. The diameter of the fixation holes should be maximum 4.5 mm. The snap-in pins are designed for a metal thickness of maximum 0.8 mm. The distance between the fixation holes is 78 mm.

4 4/8 Connector type Connection wiring is greatly simplified through use of WAGO 251 universal connector. Suitable for both automatic wiring (IDC and ADS) and manual wiring. Wire cross-section IDC connection 0.5 mm 0.75 mm 2 including stranded wiring ADS manual connection 0.5 mm mm 2 Strip length mm IDC connection ADS/Manual connection Release: rotate and pull Remark: release all wires one by one WAGO 251 universal connector. DALI distribution block Corridor = DALI 2 (Offset channel) DALI distribution block Window = DALI 1 (Master channel) Corridor DA DA Window DA DA T&D Ls Ns N Ls DALI 1 Ns N DALI 2 L Sensor DA / N DA / Ls ~ ~ DALI Ballast 230VAC GND L ActiLume Sensor Master Luminaire Mains distribution block Mains input connector PCB terminal block WAGO, series Wiring

5 5/8 ActiLume Modes Besides the two Plug and Play modes for cell office and open plan office, it is possible to recall 8 other application modes as mentioned below. This makes the ActiLume system very flexible for all different kinds of applications. With the use of the extended IR programming tool IRT9090/00 all 10 different modes can be selected.. Once selected, the mode can be stored and copied via a point and shoot method. Even when the luminaires are switched off for a longer period, stored parameters are kept. For more detailed information, please be referred to the Philips ActiLume OEM Application guide Mode 1 - Cell office 15 min. Mode 2 - Open plan office 15 min. 120 min. Mode 3 - School, classroom Manual on 15 min. Mode 4 - Open plan office 15 min. 120 min. Comfort mode EN Mode 5 - Cell office Comfort mode EN min. Mode 6 - Corridor 15 min. 60 min. Mode 7 - Toilets 15 min. 15 min. Mode 8 - Meeting rooms 15 min. Manual on No DLR Mode 10 - Open plan office 15 min. Mode 9 - Open plan office Always light 15 min. Comfort mode, always light Only task light DLR Modes

6 6/8 LCC1653/01 Controller The controller from the ActiLume system. The ActiLume system is a plug & play, DALI-based control system which fulfills the basic needs in offices with maximum energy saving options by daylight harvesting and presence detection. LCC1656/00 Controller Same as the LCC1653/01, but designed for free floor standing luminaires. When the mains is connected the light switches on (Powerstage On). LRI1653/01 Sensor The multi sensor from the ActiLume system. IRT9090/00 Extended IR programming tool Commissioning tool for OccuSwitch DALI (OccuPlus), OccuSwitch, Saber sensors and luminaires with ActiLume. Easy to use and inexpensive tool to adjust the functionality, perform an installation test and/or calibrate light levels. The functionality is depending on the product it is used with. Batteries are included. LRM8119/00 ActiLume movement extension sensor, luminaire based Compact luminaire based movement detector to be used to expand the detection area for ActiLume and OccuSwitch DALI (OccuPlus) solutions. The sensor is connected to the DALI line from the controller (luminaire) and does not require external power. Mounting height is between 2.5 and 3.5 m. LRM8118/00 Extension sensor Compact movement detector to be used to expand the detection area for ActiLume and OccuSwitch DALI (OccuPlus) solutions. The sensor is connected to the DALI line from the controller (luminaire) and does not require external power. The sensor is suitable for both recessed and surface mounting (in combination with the LRH8100/00). Mounting height is between 2.5 and 3.5 m. LRH8100/00 Surface mount adaptor Surface mounting box for the LRM8118 extension sensor. Comes with cut-out holes for most common cable trunking systems. LCA8000/00 Cover ActiLume multi sensor Cover for the ActiLume multi sensor to obtain the same outer dimensions as the ActiLume MicroLuxSense and the ActiLume 1-10V sensor. LCA8001/00 Ring for ActiLume sensors Ring around the cover of the ActiLume multisensor + cover, ActiLume luminaire based extension sensor + cover, ActiLume 1-10V sensor or ActiLume MicroLuxSense to fit in the micro-optics of a luminaire. LCA8002/00 ActiLume sensor clip for TL5 Clip to be used for ActiLume multisensor, ActiLume Luminaire based extension sensor, ActiLume 1-10V sensor and the ActiLume MicroLuxSense. With this clip the sensor can be directly clicked on the TL5 lamp. LCA8003/00 ActiLume sensor clip for TL-D Clip to be used for ActiLume multisensor, ActiLume Luminaire based extension sensor, ActiLume 1-10V sensor and the ActiLume MicroLuxSense. With this clip the sensor can be directly clicked on the TL-D lamp. LCA8004/00 Cover ActiLume extension sensor Cover for the ActiLume luminaire based extension sensor to obtain the same outer dimensions as the ActiLume MicroLuxSense and the ActiLume 1-10V sensor. LCA8005/00 ActiLume mounting clip for use in luminaire. Clip to be used for ActiLume multisensor, ActiLume Luminaire based extension sensor, ActiLume 1-10V sensor and the ActiLume MicroLuxSense. With this clip the sensor can be mounted in the luminaire housing.

7 7/8 IRT8010/00 Hand-held two-key transmitter Hand-held two-key transmitter, for infrared control of various lighting control systems. ActiLume can also dim the lights (by pressing a button > 0.5 sec). The unit is supplied with batteries. A wall holder is separately available. This transmitter is not designed to be operated from the wall holder. For use in all Lighting Controls systems with IR interface excl. Dynalite. LRH8010/00 Wall holder Wall holder for the IRT8010/00 hand-held two-key transmitter. IRT8050/00 Two-key infrared remote control Two-key infrared remote control transmitter for wall mounting and table-top use. The unit can be used in combination with ActiLume. The actual function of the two large keys can be selected with a dip switch in the battery compartment. A dip switch is also used to select the group address. Batteries are included. IRT8030/00 Four-preset hand-held transmitter Four-preset hand-held transmitter, suitable for infrared control of the ActiLume system specifically when using Mode 8 (Meeting room). It has 4 keys for presets and one key for all off. Keys for individual control and preset programming are located under a hinged cover at the bottom of the transmitter. The group address selector switch is contained in the battery compartment. The unit is supplied complete with wall holder and batteries. UID8510 IR User Interface The UID8510 IR user interface panel provides intuitive on/off and dimming functionality. It connects via infrared to the ActiLume system. Batteries are included.

8 8/8 Packing data Type Box dimensions Qty/ Material Weight (Kg) (mm) Box net gross LCC1653/ x 190 x Cardboard LCC1656/ x 190 x Cardboard LRI1653/ x 169 x Cardboard LRM8118/00 80 x 72 x 40 1 Cardboard LRH8100/00 80 x 80 x 40 1 Plastic bag LRM8119/ x 175 x Cardboard IRT9090/ x 46 x 27 1 Cardboard LCA8000/ x 93 x Cardboard LCA8001/ x 93 x Cardboard LCA8002/ x 93 x Cardboard LCA8003/ x 93 x Cardboard LCA8004/ x 93 x Cardboard LCA8005/ x 97 x Cardboard Ordering Data Type MOQ Ordering number EAN code level 1 EAN code level 3 EOC LCC1653/ LCC1656/ LRI1653/ LRM8118/ LRH8100/ LRM8119/ IRT9090/ LCA8000/ LCA8001/ LCA8002/ LCA8003/ LCA8004/ LCA8005/ /2013 Data subject to change