MULTIWAY 2-12 WAY DOOR ENTRY SYSTEM

Size: px

Start display at page:

Download "MULTIWAY 2-12 WAY DOOR ENTRY SYSTEM"

Melissa Hawkins
5 years ago
Views:

1 MULTIWAY 2-2 WAY DOOR ENTRY SYSTEM FTDEVM2-2 Instruction Rev0

2 CONTENTS Part. Product introduction. Panel(s) layout.2 Specification Part 2. Connection 2. Cable requirements 2.2 Cables and distance 2.3 Terminals 2.4 System diagrams 2.5 Connection diagrams for other devices 2.6 Power supply arrangement Part 3. System programming 3. Call button numbers and address 3.2 Indoor phone address setting 3.3 Isolation module Part 4. Operation 4. Operation on door station 4.2 Operation on indoor phone Part 5. Installation 5. Installation of door station 5.2 Installation of Indoor phone/handset 5.3 Installation of isolation module 5.4 Installation of power supply Page ~3 3 4~ ~ ~ ~

Microphone colour camera Speaker name tag call button name

4 button screws Model FTDEVM7 Microphone Emergency button

Speech volume adjustor Image adjustors Model FTDEVM4

3 Part Product Introduction. Panel(s) layout screws frame White/IR LEDs light sensor Microphone colour camera Speaker name tag call button name tag call button No.4 button screws Model FTDEVM7 Microphone Emergency button Standby Monitor button Unlock button Answer button Speaker Speech volume adjustor Image adjustors Model FTDEVM4 Speaker Power indicator Emergency button Monitor button Unlock button Answer button Microphone M - + Image adjustors Speech volume adjustor

Model FTDEAH Speaker Keypad Screw Handset Switch hook Alarm

Microphone Coil cord Isolation module FTDEIM Power terminals RJ45

indicator RJ45 ports to indoor phones Power supply (2V&32V)

4 Model FTDEAH Speaker Keypad Screw Handset Switch hook Alarm indicator Alarm-activated button Emergency button Unlock button Microphone Coil cord Isolation module FTDEIM Power terminals RJ45 ports to next module(optional) Rj45 port to door station Power indicator RJ45 ports to indoor phones Power supply (2V&32V) FTDEPSU2 & FTDEPSU32 Power input terminals Power output terminals Power indicators 2

5 .2 Specification.2. Door station Camera: Viewing angle: Lens: Resolution: Min. Illumination: Video Output: Audio SNR: Audio Distortion: Assistant door panel: System Capacity: Standby Current: Working Current: Power supply: Environment Temperature: /3" CCD 92 F= TV Lines 0.0 Lux V P-P/75Ω 25dB 7% pc(8 buttons) 2 apartments 6mA 450mA DC2V ±0% -40 ~ Indoor phones Display: Resolution: Video input: Audio SNR: Audio distortion: Standby current: Working current: Power supply: Environment temperature: 4.3" & 7" TFT-LCD (colour) TFT-LCD: 660x234 pixel (4.3"); 440x234 pixel (7"); V P-P/75Ω 25dB 7% 60mA 260mA DC32V±0% & DC2V±0% -25 ~ Isolation module Working voltage: Working current: Video input: Video output: Audio output: Environment temperature: DC2V & DC32V 200mA 0.7V P-P~.2V P-P/75Ω V P-P/75 Ω, 4 routes 4 routes -40 ~ Power supplies Power: Voltage input: Voltage output: Current output: Working voltage: 40W(FTDEPSU2; FTDEPSU32) AC00V~240V/50-60Hz 0.5Amax. DC 2V±0%; DC 32V±0%.25A; 3A -40 ~+70 3

0 mm (AWG8) Please follow TIA/EIA-568B Standard for CAT-5(E) cables to avoid interference. 2.

75) <30m 50m 0Ω 0Ω Module to next module FTP-5E(.5) <40m (Please see details in 3.3.) 0Ω Power supply to modules RVV(2X.0) <30m Min.

3 Terminals A, Door station Model FTDEPC4 JP5 JP2 2V- AU 32VIN V- 2V+ SGND ETRXD V+ R- T+ A+ VM- R+ A- T- VM+ ALM G UL G Jp6 6 JP8 5 3 Jp3 2V+

6 Part 2 Connection 2. Cable requirements: A, Cable from door station to modules/ indoor phones B, Cable to door stations/modules CAT-5/E cable RJ45 Port 2 RVV2x.0 mm (AWG8) Please follow TIA/EIA-568B Standard for CAT-5(E) cables to avoid interference. 2.2 Cables and distance Wires Type(size) Distance Wire resistance Door station to module Modules to indoor phones FTP-5E(.5) UTP-5(0.75) <30m 50m 0Ω 0Ω Module to next module FTP-5E(.5) <40m (Please see details in 3.3.) 0Ω Power supply to modules RVV(2X.0) <30m Min. gap: 50cm, between low voltage and high voltage. 2.3 Terminals A, Door station Model FTDEPC4 JP5 JP2 2V- AU 32VIN V- 2V+ SGND ETRXD V+ R- T+ A+ VM- R+ A- T- VM+ ALM G UL G Jp6 6 JP8 5 3 Jp3 2V+ 2V- DATA 2V+ 2V- L+ L- JP POWER UNLOCK COM NC NO 4 Jp4 2 JP2 B, Assistant door panel Model FTDEP4, FTDEP8 SW2 ADDR0 6 EXT KEY SW22 ADDR 7 SW23 2V G DATA SW24 ADDR2 ADDR3 RJ45 port to isolation module. 2Standby. 3Terminals to power supply & e-lock(power type). 4Terminals to e-lock (signal type). 5Terminals to EXIT push button. 6Terminals between door station FTDEPC4 and assistant door panels. 7Jumper couplers for coding assistant door panels. 4

7 2.4 System Diagrams 2.4. Basic component diagram A, For FTDEV-4 and FTDEV5-8 kit Isolation module CAT5 Isolation module Video indoor phone CAT5E 2 RVV2x.0mm PSU 32 3wires 2 RVV2x.0mm PSU 2 Assist door panel Video door station 5

8 B, For FTDEV9-2 kit Isolation module Isolation module CAT5 Isolation module Video indoor phone CAT5E 2 RVV2x.0mm PSU 32 3wires 2 RVV2x.0mm PSU 2 PSU 2 Assist door panel Video door station 6

9 ALM G UL G 2V+ 2V- L+ L- POWER UNLOCK 2V+ 2V- DATA COM NC NO Basic wiring diagram CALL 2VIN G AF ETRXD 32VIN V+ V- ALM To other indoor phones To next module Video indoor phone Isolation module CALL 2VIN G AF ETRXD 32VIN V+ V- ALM OUT-4 OUT-3 OUT-2 OUT- Isolation module SGNG +32V G +2V SOUT POUT INPUT SGNG +32V G +2V SOUT POUT INPUT OUT-4 OUT-3 OUT-2 OUT- To other indoor phones Video indoor phone PSU 32 PSU 2 SW2 ADDR0 2V- AU 32VIN V- JP 5 Jp2 R- T+ A+ VM- 6 EXT KEY 2V G DATA SW22 ADDR 7 SW23 ADDR2 SW24 ADDR3 2V+ SGND ETRXD V+ JP 5 JP6 3 JP3 6 JP8 4 JP 4 R+ A- T- VM+ 2 JP2 All terminals of N, L and have to be connected to the AC power. 7

2V- AU 32VIN V- 2V+ SGND ETRXD V+ 2V- AU 32VIN V- 2V+ SGND ETRXD V+ 2V- AU 32VIN V- 2V+ SGND ETRXD V+ ALM G UL G 5 JP3 2V+ 2V- L+ L- POWER UNLOCK ALM G UL G JP3 2V+ 2V- L+ L- POWER UNLOCK ALM G UL G

5 Connection diagram for other devices 2.5. Wiring diagram of doorbell push button Doorbell button CALL G Video indoor phone 2.5.2 Wiring diagram of EXIT push button ALM G UL G JP5 JP2 JP6 6JP8 3 DOOR JP 4 JP4 2 JP2 EXIT EXIT Momentary normally Open push button Door station FTDEPC4 2.

10 2V- AU 32VIN V- 2V+ SGND ETRXD V+ 2V- AU 32VIN V- 2V+ SGND ETRXD V+ 2V- AU 32VIN V- 2V+ SGND ETRXD V+ ALM G UL G 5 JP3 2V+ 2V- L+ L- POWER UNLOCK ALM G UL G JP3 2V+ 2V- L+ L- POWER UNLOCK ALM G UL G JP3 2V+ 2V- L+ L- POWER UNLOCK 2V + 2V - DATA COM NC NO 2V + 2V - DATA COM NC NO 2V + 2V - DATA COM NC NO R- T+ A+ VM- R+ A- T- VM+ R- T+ A+ VM- R+ A- T- VM+ R- T+ A+ VM- R+ A- T- VM+ 2.5 Connection diagram for other devices 2.5. Wiring diagram of doorbell push button Doorbell button CALL G Video indoor phone Wiring diagram of EXIT push button ALM G UL G JP5 JP2 JP6 6JP8 3 DOOR JP 4 JP4 2 JP2 EXIT EXIT Momentary normally Open push button Door station FTDEPC Wiring diagrams of lock releases and electromagnetic locks JP5 JP2 5 3 JP6 6 JP8 JP 4 JP4 2 JP2 Lock release COM NC NO + - Power supply JP5 JP2 Break 5 3 JP6 6 JP8 glass JP 4 JP4 2 JP2 N/C COM + - Door station FTDEPC4 Touch to release DIODE _ + Electromagnetic lock This device comes with a varistor. A varistor (or diode) must be connected across the lock terminal as the varistor controls the overload produced by the strike coil or maglock. If not used then this may cause inerasable damage. If a maglock is to be used then an extra PSU, break glass, push button to exit may be required. Please arrange according to your need. 8

11 2V- AU 32VIN V- 2V+ SGND ETRXD V+ ALM G UL G JP3 2V+ 2V- L+ L- POWER UNLOCK 2V+ 2V- DATA COM NC NO R- T+ A+ VM- R+ A- T- VM Wiring diagram of power supply JP5 JP2 5 3 JP6 6 JP8 JP 4 JP4 2 JP2 2V- 2V+ PSU 2 Door station FTDEPC4 2.6 Power supply arrangement The power supply's capacities are as the following table. Please arrange the power supply for projects accordingly. Power supply Audio indoor phone Video indoor phone Isolation module FTDEPSU2 20pcs 6pcs 4pcs FTDEPSU32-6pcs 4pcs 9

12 ALM G UL G 2V+ 2V- L+ L- POWER UNLOCK 2V+ 2V- DATA COM NC NO Part 3 System programming 3. Call button numbers and address A, The door station and assistant door panels' call button numbers are ranked as the following figures. No.000 No.0002 No.0003 No.0004 No.0005 No.0006 No.0007 No.0008 No.0009 No.000 No.00 No.002 B, Assistant door panels' address (for 5-2 way only) On the back of the assistant door panel there are 4 jumper couplers. Please ensure jumper setting is set as below. If there is no assistant door panel, please ignore this part and go to next part directly. Address code No. 0 Jumper couplers' arrangement SW SW2 SW3 SW4 Call button No. 0005~ Indoor phone address setting 3.2. Wiring Prepare the cables and wire the necessary devices with the enclosed terminal connectors as the following diagram. (If there is any assistant door panel, please connect it also.) CALL 2VIN G AF ETRXD 32VIN V+ V- ALM To other indoor phones Video indoor phone Isolation module SGNG +32V G +2V SOUT POUT INPUT OUT-4 OUT-3 OUT-2 OUT- PSU 32 JP5 JP2 2V- AU 32VIN V- R- T+ A+ VM- 2V+ SGND ETRXD V+ R+ A- T- VM+ 5 JP6 3 JP3 6 JP8 PSU 2 JP 4 JP4 2 JP2 Power supply Power supply Door station FTDEPC4 PSU 2 0

13 3.2.2 To program the out door station s call buttons the relevant indoor phones Step > Match indoor phone with call buttons Push both and buttons and do not release them, then push a specific call button for 2 seconds as the following figures. If the program is successful, both door station and indoor phone will sound double short beeps. Mark the call button number on a proper position of the indoor phone. 2" + Step 2> Remove the programmed indoor phone, and connect the next indoor phone. Step 3> Repeat step and 2 for the other indoor phones. In case any programmed indoor phone has to match with another call button, please just do as Step but choose the correct call button. 2If any apartments need more indoor phones, please just program these indoor phones to match with the same call button. 3.3 Isolation Module (FTDEIM) The isolation modules have the functions of audio & video signal distribution, amplification and malfunction isolation. Each module supports up to 4 indoor phones. Indoor phones are workable in 50 meters from their modules Jumper couplers There are jumper couplers in the back of the modules (as the following figures). Please arrange them according to different applications. F 2F M 00 F 2F M 00 F M(default) F 00 2F 00 F 2F M 00 For FTDEV-4 kit, jumper couplers of the only module is at the place F 00"; 2 For FTDEV5-8 kit, jumper couplers of the st module is at the place F M, the 2nd module is at the place F 00"; 3 For FTDEV9-2 kit, jumper couplers of the st and 2nd modules is at the place F M, the 3rd module is at the place F 00" Wiring Application : Distance is in 30 meters between two modules. No.:F M No.2:F M No.3:F 00 INPUT Pout INPUT Pout INPUT <30m <30m Application 2: Distance 30 meters between two modules, please make sure it doesn t exceed 40 meters. No.:F M No.2:F M No.3:F 00 INPUT INPUT INPUT Sout Sout 30m-40m 30m-40m

Part 4 Operation 4. Operation on door station Push a call button on door station to c all indoor phones. In case push a wrong call button, the visitors may push the same button again.

14 Part 4 Operation 4. Operation on door station Push a call button on door station to c all indoor phones. In case push a wrong call button, the visitors may push the same button again. Then the calling can be cancelled immediately Operation on indoor phone 4.2. Answer Push the button as the following figures. The communication is allowed in 75 seconds. 2If you need to end the communication, please push button Release doors While at intercom status please push button to release the door as the following figures Video surveillance Please p ush button when need to surveil the door station. During surveillance status, you could push button and talk to door station. During the communication status, you could push button to release the lock. 2 29

15 4.2.4 Family intercom If there are 2 or more indoor phones in your family, you could use an indoor phone to call another by pushing button and then button Change ring tone Push button for more than 2 seconds when the indoor phone is idle, and then push the button again and again until you get a favourite ring tone. There are more than 0 melody ring tones. 2" Adjust image quality Push button to show the image, then push MENU, + and - buttons to get a good quality image. MENU - + For longer time to adjust image quality, you may push button, then push button to be in communication status Adjust speech volume Turn the wheel as the following figure

16 Part 5 Installation Before install the devices please read these notices: Suggested panel height.4m-.8m; 2Do not install the devices with high voltage, high temperature, a strong magnetic field, corrosive, or humid atmospheres. 3Make sure the lens and microphone are protected from dust. 4To reduce silhouetting of camera image, avoid installing panel in areas that receive direct sunlight. 5. Installation of door station Screws Panel Seal Box 2 Frame 3 a. Cut out a rectangular hole as the installation size (04x24x50mm) on a suitable position and then fix the box in it with cement or screws(). b. Take off the screws and then the frame(2). c. Put the rubber seal on the back of door panel(3). d. Put the door panel into the box and fix it with the screws(3) after connection. e. Put the frame on the door panel and fix it with the screws(2). 5.. Dismantle/install name tags 2 Dismantle: Press the right or left edge hard. Install: Insert the name tag. 2 Press the edge. 4

17 5.2 Installation of Indoor phone/handset 5.2. Install video indoor phone All video indoor phones are mounted with brackets on the wall, in the same way as the following steps. There are different size brackets. Please use the matched ones for your indoor phones. Hook expansion plugs 3 2 a. Fix the bracket on the wall with the screws ( or 2). b. Move the indoor phone and put it on the bracket after connect the cable( 3). Indoor phone bracket Install audio handset expansion plugs installation holes l jk screws Figure A Figure B a. Measure the gap between two installation holes. b. Install the expansion plugs and screws in the wall as Figure A ( 2).Please leave the screws raised a proper length from the wall. c. Move the audio handset close to the raised screws. Use the raised screws and installation holes to hand up the audio handset on the wall after connection as Figure B( 3). 5.3 Installation of isolation module 2 Fix the rail. Hang the box on the rail. Pull out the latch, push the box on the rail and then release the latch. 5.4 Installation of power supply The same as 5.3. Fused spur should be used for mains supply to PSU s. 2Products may be demaged if the power is over the range. 3Connect the terminal( )of the power supply to the Groud terminal of the products. 4Do not open the casing. 5Do not install the power supply externally or in dusty environment. 6Eusure power supplies are well ventilated. 7Installation position should be not less than.5mm. 5 3

18 Notes:

Due to our policy of continuous improvement we reserve the right to change specification without prior notice. Errors and omissions excepted.

19 Due to our policy of continuous improvement we reserve the right to change specification without prior notice. Errors and omissions excepted. These instructions have been carefully checked prior to publication. However, no responsibility can be accepted by Challenger Security Products for any misinterpretation of these instructions. Distributed by: CHALLENGER SECURITY PRODUCTS 0 Sandersons Way, Blackpool, FY4 4NB Technical helpline: enquiries.challenger@adivision.co.uk Website: FTDEVM2-2 Instruction Rev0

8. Electric Lock Connection

8. Electric Lock Connection 6. Switches Settings Total 6 bits in the switches can be configured. The switches can be modified either before or after installation. 1 3 5 6 (1) OFF (0) = = Bit1,Bit and Bit 3 are used for door station