Symantec S500 Network Interface Card Options and Installation

Transcription

1 Symantec S500 Network Interface Card Options and Installation Guide Revision: 4/28/2017

2 2

3 Legal Notices Copyright 2017 Symantec Corp. All rights reserved. Symantec, the Symantec Logo, the Checkmark Logo, Blue Coat, and the Blue Coat logo are trademarks or registered trademarks of Symantec Corp. or its affiliates in the U.S. and other countries. Other names may be trademarks of their respective owners. This document is provided for informational purposes only and is not intended as advertising. All warranties relating to the information in this document, either express or implied, are disclaimed to the maximum extent allowed by law. The information in this document is subject to change without notice. THE DOCUMENTATION IS PROVIDED "AS IS" AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID. SYMANTEC CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, PERFORMANCE, OR USE OF THIS DOCUMENTATION. THE INFORMATION CONTAINED IN THIS DOCUMENTATION IS SUBJECT TO CHANGE WITHOUT NOTICE. SYMANTEC CORPORATION PRODUCTS, TECHNICAL SERVICES, AND ANY OTHER TECHNICAL DATA REFERENCED IN THIS DOCUMENT ARE SUBJECT TO U.S. EXPORT CONTROL AND SANCTIONS LAWS, REGULATIONS AND REQUIREMENTS, AND MAY BE SUBJECT TO EXPORT OR IMPORT REGULATIONS IN OTHER COUNTRIES. YOU AGREE TO COMPLY STRICTLY WITH THESE LAWS, REGULATIONS AND REQUIREMENTS, AND ACKNOWLEDGE THAT YOU HAVE THE RESPONSIBILITY TO OBTAIN ANY LICENSES, PERMITS OR OTHER APPROVALS THAT MAY BE REQUIRED IN ORDER TO EXPORT, RE-EXPORT, TRANSFER IN COUNTRY OR IMPORT AFTER DELIVERY TO YOU. Symantec Corporation 350 Ellis Street Mountain View, CA

4 Contents Legal Notices 3 Safety Warnings and Cautions 5 Power and Electrical Warnings 5 CAUTION 5 System Access Warnings 5 CAUTION 5 To avoid personal injury or property damage, the following safety instructions apply whenever accessing the inside of the product: 5 CAUTION 6 CAUTION 6 Cooling and Airflow Warning 6 Electrostatic Discharge (ESD) Warning 6 CAUTION 6 Network Interface Card Options 7 Install an option card into Slot 1 or 2 18 Install an option card into Slot 3 or 4 20 Install an option card into Slot 5 or 6 24 Install an option card into Slot 7 27 Open the S500 Series Center Cover 29 Remove the S500 Series Rear Cover 30 Remove the S500 Series PCIe Expansion Module 31 Install the S500 Series PCIe Expansion Module 32 4

5 Safety Warnings and Cautions Caution: This product is designed to work with power systems having a grounded neutral. To reduce the risk of electric shock, do not plug this product into any other type of power system. Contact a qualified electrician if you are not sure what type of power is supplied to your building. Power and Electrical Warnings CAUTION The power button, indicated by the stand-by power marking, DOES NOT completely turn off the system AC power. 5V standby power is active whenever the system is plugged in. To remove power from system, you must unplug the AC power cord from the wall outlet. If your system uses more than one AC power cord, make sure all AC power cords are unplugged before you open the chassis, or add or remove any non hotplug components. The power supply in this product contains no user-serviceable parts. Do not open the power supply. Hazardous voltage,current, and energy levels are present inside the power supply. Return to manufacturer for servicing. To avoid risk of electric shock, turn off the appliance and disconnect the power cord, telecommunications systems, networks, and modems attached to the appliance before opening it. The power cord set included with the appliance meets the requirements for use in the country of purchase. Use the power cord that shipped with the appliance. If this appliance is to be used in another country, purchase an AC power cord set that is approved for use in that country (18 AWG recommended). The power cord must be rated for the product and for the voltage and current marked on the product's electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the cross-sectional area of the wires must be a minimum of 1.00mmð or 18AWG or 18AWG, and the length of the cords must be between 1.8m (6 feet) and 3.6m (12 feet). System Access Warnings CAUTION To avoid personal injury or property damage, the following safety instructions apply whenever accessing the inside of the product: Turn off all peripheral devices connected to this product. Turn off the system by safety shutting down the appliance. Disconnect the AC power by unplugging all AC power cords from the system or wall outlet. Disconnect all cables and telecommunication lines that are connected to the system. Retain all screws or other fasteners when removing access cover(s). Upon completion of accessing inside the product, refasten access cover with original screws or fasteners. 5

6 Do not access the inside of the power supply. There are no serviceable parts in the power supply. Return to manufacturer for servicing. Power down the server and disconnect all power cords before adding or replacing any non hot-plug component. When replacing a hot-plug power supply, unplug the power cord to the power supply being replaced before removing the power supply from the server. CAUTION If the server has been running, any installed processor(s) and heat sink(s) may be hot. Unless you are adding or removing a hot-plug component, allow the system to cool before opening the covers. To avoid the possibility of coming into contact with hot component(s) during a hot-plug installation, be careful when removing or installing the hot-plug component(s). CAUTION To avoid injury do not contact moving fan blades. If your system is supplied with a guard over the fan, do not operate the system without the fan guard in place. Cooling and Airflow Warning Carefully route cables as directed to minimize airflow blockage and cooling problems. For proper cooling and airflow, operate the system only with the chassis covers installed. Operating the system without the covers in place can damage system parts. To install the covers: 1. Check first to make sure you have not left loose tools or parts inside the system. 2. Check that cables, add-in boards, and other components are properly installed. 3. Attach the covers to the chassis according to the product instructions. Electrostatic Discharge (ESD) Warning CAUTION ESD can damage disk drives, boards, and other parts. We recommend that you perform all procedures at an ESD workstation. If one is not available, provide some ESD protection by wearing an antistatic wrist strap attached to chassis ground- any unpainted metal surface -- on your server when handling parts. Always handle boards carefully. They can be extremely sensitive to ESD. Hold boards only by their edges. After removing a board from its protective wrapper or from the server, place the board component side up on a grounded, static free surface. Use a conductive foam pad if available but not the board wrapper. Do not slide board over any surface 6

7 Network Interface Card Options The following lists the option cards that are available for the S500-based appliances. The low-profile option cards can be installed into any of the PCIe slots, including the on-board PCIe slots and the PCIe expansion module slots. Full-height cards, with a system maximum of 2, can only be installed in the PCIe expansion module, slots 3 and 4. Option cards are shipped with a pre-installed bracket that might not be compatible with your appliance or desired slot usage. You must replace the bracket with the necessary version before installing an option card. Be sure to verify that your product supports the option card before installation. S500 Series-based appliances equipped with a single CPU cannot use slots 5, 6, and 7. Please select the option card that you wish to install: Review the "Safety Warnings and Cautions" on page 5 before servicing your appliance. Do not install any NIC (network interface cards) which are not explicitly supported by the appliance. Installation and use of unauthorized NICs might damage the appliance and will invalidate your warranty! Network Card Supported Appliances Description Expansion Slot Usage Installation NIC-S500-2x10G-PT ProxySG PacketShaper ASG 2-port 10GBASE-T Pass-through (click for details) All expansion slots I'd like to install the option card in: Slot 1 or 2 Slot 7 Slot 3 or 4 (PCIe expansion module) Slot 5 or 6 (PCIe expansion module) NIC-S500-4xGigE-PT- Fiber ProxySG PacketShaper ASG 4-port 1000BASE-SX Pass-through, Fiber, Small form Factor Pluggable (LC) (click for details) Only installable in slots 3 or 4. I'd like to install the option card in: Slot 3 or 4 (PCIe expansion module) NIC-S500-4xGigE-PT ProxySG PacketShaper ASG 4-port 1000BASE-T Passthrough (click for details) All expansion slots I'd like to install the option card in: Slot 1 or 2 Slot 7 Slot 3 or 4 (PCIe expansion module) Slot 5 or 6 (PCIe expansion module) 7

8 Network Card Supported Appliances Description Expansion Slot Usage Installation NIC-S500-2x10G 2-port 10GBASE-T Nonbypass NIC-S500-2x10G-PT- SR-Fbr NIC-S500-2x10G-PT- LR-Fbr NIC-S500-4xGigE-LX- Fiber) ProxySG Malware Analysis ASG ProxySG PacketShaper ASG ProxySG PacketShaper ASG ProxySG PacketShaper ASG (click for details) 2-port 10GBASE-SR Pass-Through,10 Gigabit (SFP+) (click for details) 2-port 10GBASE-LR Pass-Through, 10 Gigabit (SFP+) (click for details) 4-port 1000BASE-LX Single Mode, Passthrough, Fiber, LC Connector All expansion slots I'd like to install the option card in: Slot 1 or 2 Slot 7 Slot 3 or 4 (PCIe expansion module) Slot 5 or 6 (PCIe expansion module) All expansion slots I'd like to install the option card in: Slot 1 or 2 Slot 7 Slot 3 or 4 (PCIe expansion module) Slot 5 or 6 (PCIe expansion module) All expansion slots I'd like to install the option card in: Only installable in slots 3 or 4. Slot 1 or 2 Slot 7 Slot 3 or 4 (PCIe expansion module) Slot 5 or 6 (PCIe expansion module) I'd like to install the option card in: Slot 3 or 4 (PCIe expansion module) 8

9 The 10 Gigabit Ethernet bypass NIC cards [NIC-S500-2x10G_PT / NIC-S400-2x10G_PT] are PCIe x8 network adapters containing two copper 10 Gigabit interfaces. Key Features WDT Interval (Software Programmable): 3,276,800 msec (3,276.8 Sec): Maximum 100 msec ( 0.1 Sec) : Minimum WDT Interval = (2^wdt_interval_ parameter)*(0.1) sec. wdt_interval_parameter: { Valid Range: 0-15} IEEE Standard / Network topology: Copper 10Gigabit Ethernet, 10GBASE-T, IEEE 802.3an Gigabit Ethernet, 1000Base-T 100 Mb Ethernet : 100BASE- TX Data Transfer Rate: 20 Gb/s, 2000Mb/s and 200 Mb/s in full duplex mode per port. Cables and Operating distance: 100Base-Tx Category 5 maximum 50m* 1000Base-T Category 5E maximum 50m* 10GBase-T Category 6A maximum 50m** Technical Specifications Interface Standard: PCI-Express Base Specification Revision 2.1 (5GT/s) Board Size: mm X 68.91mm (6.60 X ) PCI Express Card Type: X8 Lane PCI Express Voltage: +12V ± 8% PCI Connector: Gold Finger - X8 Lane Controller: Intel x540 Holder: Metal Bracket I/O: RJ45 Weight: 170gr (5.997oz) Power Consumption: 18 W, 1.5 A at 12V: Typical all ports operate at 10Gb/s, (Normal Mode) W, 0.87 A at 12V: Typical all ports operate at 1Gb/s, (Normal Mode) W, 0.63 A at 12V: Typical all ports operate at 100Mb/s, (Normal Mode) W, 0.74 A at 12V: Typical Bypass Mode W, 0.74 A at 12V: Typical Disconnect** Mode W, 0.68 A at 12V: Typical No link at all ports LEDs: (2) LED per port Upper (Left) LED: Link /ACT: Turns on link, blinks on activity (green) Lower (Right) LED: Speed / Bypass / Disconnect* Link of 1Gb/s: Turns on link (yellow) Link of 10Gb/s: Turns on link (green) Bypass: Blink (Green) on Bypass Disconnect* : Blink (Yellow) *Theoretical Distance Defined as half a distance as stated by the IEEE standard **Theoretical Distance Defined as half a distance as stated by the IEEE 802.3an standard LEDs location: LEDs are located in the RJ45 connector port. Connector: (2) Shielded RJ-45 9

10 The quad port Gigabit Ethernet bypass NIC cards [NIC-S500-4xGigE-PT-Fiber / NIC-S400-4xGigE-PT-Fiber] are PCIe x4 network adapters containing four fiber Gigabit interfaces, based on a single chip, non-bridged GBE controller. Key Features Fiber Gigabit Ethernet 1000Base-SX:: Independently Fiber Gigabit Ethernet channel/s support Gigabit Ethernet 1000Base-SX. Small Form Factor (SFF) LC Connectors. WDT Interval (Software Programmable): 3,276,800 msec (3,276.8 Sec): Maximum 100 msec ( 0.1 Sec) : Minimum WDT Interval = (2^wdt_interval_parameter)*(0.1) sec. wdt_interval_parameter: { Valid Range: 0-15} IEEE Standard / Network topology: Fiber Gigabit Ethernet, 1000Base-SX (850nM) Full duplex / Simplex: Support both Simplex & Full duplex operation in all operating speeds Auto negotiation: Auto-negotiation between Full duplex and simplex operations and between 10Mb/s 100Mb/s speeds and duplex 1000Mb/s. Data Transfer Rate: 2000Mbit/s in full duplex mode per port Cables and Operating distance: Multimode fiber - 137m maximum at 62.5 um * Technical Specifications Interface Standard: PCI-Express Base Specification Revision 2.1 (5GT/s) Board Size: mm X mm (6.60 X ) PCI Express Card Type: X4 Lane PCI Express Voltage: +3.3V +-9%, +12V +- 8% PCI Connector: Gold Finger - X4 Lane Controller: Intel i350am4 Holder: Metal Bracket I/O: LC Weight: 330g (11.641oz) Power Consumption: 0.40A, 4.8W at 12V: Typical all ports operate at 1000Mb/s. 0.40A, 4.8W at 12V: Typical No link at all ports. 0.38A, 4.56W at 12V: Bypass Mode. 0.38A, 4.56W at 12V: Disconnect Mode. LEDs: (1) LED per port Link/ACT: Blinks on activity (green). Turns on link (green). Bi-color LED per Bypass pair: BYPASS: Turns on Green on Bypass Disconnect : Turns on Yellow on Disconnect Normal: Off LEDs location: LEDs are located on the PCB, visible via holes in the metal bracket holder Connector: (4) LC *Theoretical Distance Defined as half a distance as stated by the IEEE standard 10

11 The quad port Gigabit Ethernet bypass NIC cards [NIC-S500-4xGigE-PT / NIC-S400-4xGigE-PT] are PCIe x4 network adapters containing four copper Gigabit interfaces, based on a single chip, non-bridged GBE controller. Key Features Copper Gigabit Ethernet 1000Base-T: Independently copper Gigabit Ethernet channels support four Gigabit Ethernet (1000Base-T), Fast Ethernet (100Base-Tx) and Ethernet (10Base-T). Triple speed 1000Mbps (1000Base- T), 100 Mbps (100Base-Tx) and 10 Mbps (100Base-T) operation. Nway auto negotiation automatic sensing and switching between 1Gbps full duplex and 100 / 10 Mbps operations Simplex or Full Duplex. RJ-45 female connectors. WDT Interval (Software Programmable): 3,276,800 msec (3,276.8 Sec): Maximum 100 msec ( 0.1 Sec) : Minimum WDT Interval = (2^wdt_interval_ parameter)*(0.1) sec. wdt_interval_parameter: { Valid Range: 0-15} IEEE Standard / Network topology: Gigabit Ethernet, 1000Base-T Fast Ethernet, 100Base-TX Ethernet, 10Base-T Technical Specifications Interface Standard: PCI-Express Base Specification Revision 2.1 (5GT/s) Board Size: mm X 68.91mm (6.60 X ) PCI Express Card Type: X8 Lane PCI Express Voltage: +12V ± 8% PCI Connector: Gold Finger - X8 Lane Controller: Intel i350am4 Holder: Metal Bracket I/O: RJ45 LEDs: (2) LED per port Link / Act Led: Turn on any Link speed, Blinks on Activity (green) Speed/Bypass/Disconnect (Bi-color) Led: 1000Mb/s: Turns on Yellow 100Mb/s: Turns on Green. 10Mb/s: Turns off Disconnect: Blink Yellow Bypass: Blink Green LEDs location: LEDs are integrated on RJ-45 connector Connector: (4) Shielded RJ-45 11

12 Key Features Technical Specifications Full duplex / Simplex: Support both Simplex & Full duplex operation in all operating speeds Auto negotiation: Auto-negotiation between Full duplex and simplex operations and between 10Mb/s 100Mb/s speeds and duplex 1000Mb/s. Data Transfer Rate: 1000 Mb/s, 100 Mb/s and 10 Mb/sec in simplex mode per port. 2000Mb/s 200 and 20 Mb/s in full duplex mode per port. Cables and Operating distance: 10Base-T Category 3, 4, or 5 maximum 50m * 100Base-Tx Category 5 maximum 50m * 1000Base-T Category 5E maximum 50m * *Theoretical Distance Defined as half a distance as stated by the IEEE standard 12

13 The 10 Gigabit Ethernet PCIe non-bypass NIC cards [NIC-S500-2x10G / NIC-S400-2x10G] contain two copper 10 Gigabit interfaces. Key Features IEEE Standard / Network topology: Copper 10Gigabit Ethernet, 10GBASE-T, IEEE 802.3an Gigabit Ethernet, 1000Base-T 100 Mb Ethernet : 100BASE- TX Data Transfer Rate: 20 Gb/s, 2000Mb/s and 200 Mb/s in full duplex mode per port. Cables and Operating distance: 100Base-Tx Category 5 maximum 100m 1000Base-T Category 5E maximum 100m 10GBase-T Category 6A maximum 100m Technical Specifications Interface Standard: PCI-Express Base Specification Revision 2.1 (5GT/s) Board Size: 251.4mm X 68.91mm (6.0 X ) PCI Express Card Type: X8 Lane PCI Express Voltage: +12V ± 8% PCI Connector: Gold Finger - X8 Lane Controller: Intel x540 Holder: Metal Bracket I/O: RJ45 Weight: 130g Power Consumption: W, 1.19 A at 12V: Typical all ports operate at 10Gb/s, (Normal Mode) W, 0.66 A at 12V: Typical all ports operate at 1Gb/s, (Normal Mode) W, 0.42 A at 12V: Typical all ports operate at 100Mb/s, (Normal Mode) W, A at 12V: Typical No link at all ports LEDs: (2) LED per port Speed LED: Link of 1Gb/s: Turns on link (yellow) Link of 10Gb/s: Turns on link (green) Link /ACT LED: Turns on link, blinks on activity (green) LEDs location: LEDs are located in the RJ45 connector port. Connector: (2) Shielded RJ-45 13

14 The dual port fiber 10 Gigabit Ethernet bypass NIC cards [NIC-S500-2x10G_PT_SR_fbr / NIC-S400-2x10G_ PT_SR_fbr] are PCIe x8 network adapters containing two fiber (SR) 10 Gigabit interfaces. Key Features 10 Gigabit Fiber Ethernet port supports 10GBASE-SR (850nM LAN PHY) 10Gigabit Technical Specifications Interface Standard: PCI-Express Base Specification Revision 2.0 (5GT/s) Board Size: mm X 68.91mm (6.60 X ) 850nM Small form Factor Pluggable (SFP+) PCI Express Card Type: X8 Lane PCI Express Voltage: +12V ± 8% WDT Interval (Software Programmable): 3,276,800 msec (3,276.8 Sec): Maximum 100 msec ( 0.1 Sec) : Minimum WDT Interval = (2^wdt_interval_ parameter)*(0.1) sec. wdt_interval_parameter: { Valid Range: 0-15} IEEE Standard / Network topology: Fiber 10 Gigabit Ethernet, 10GBase-SR (850nM) Data Transfer Rate: GBd Cables and Operating distance: PCI Connector: Gold Finger - X8 Lane Controller: Intel 82599ES Holder: Metal Bracket I/O: SR Weight: 200g (7.055Oz) Power Consumption: 6.6 W, 0.55 A at 12V: Typical all ports operate at 10Gb/s, (Normal Mode) W, 0.51 A at 12V: Typical Bypass Mode W, 0.53 A at 12V: Typical No link at all ports Multimode fiber: 62.5um, 160MHz/Km 26m 62.5um, (OM1)200MHz/Km 33m 50um, 400MHz/Km 66m 50um, (OM2)500 MHz/Km 82m 50um, (OM3)2000MHz/Km 300m 14

15 Key Features Optical Output Power: Normal Mode (Bypass Off): Typical: -3.1dBm (TX Switch Normal Fiber LC/LC) Minimum: -7.3 dbm Technical Specifications LEDs: (2) LED per port Link: Turns on Blue on 10G link. ACT: Blinks on activity (green). Bi-color LED per Bypass pair: BYPASS: Turns on Green on Bypass Disconnect : Turns on Yellow on Disconnect Normal: Off Optical Receive Sensitivity: LEDs location: LEDs are located on the PCB, visible via holes in the metal bracket holder Connector: (2) SR Normal Mode (Bypass Off) Insertion Loss: Typical: dbm Maximum: -11 dbm Bypass Mode: Insertion loss (Optical Power attenuation between TX to RX) (LCfiber- switch- LC) Typical: 0.39 db (From RX to TX) Maximum 1.6 db 15

16 The dual port fiber 10 Gigabit Ethernet bypass NIC cards [NIC-S500-2x10G_PT_LR_fbr / NIC-S400-2x10G_ PT_LR_fbr] are PCIe x8 network adapters containing two fiber (LR) 10 Gigabit interfaces. Key Features 10 Gigabit Fiber Ethernet port supports 10GBASE-LR (1310nM LAN PHY) Technical Specifications Interface Standard: PCI-Express Base Specification Revision 2.0 (5GT/s) Board Size: mm X 68.91mm (6.60 X ) WDT Interval (Software Programmable): 3,276,800 msec (3,276.8 Sec): Maximum 100 msec ( 0.1 Sec) : Minimum WDT Interval = (2^wdt_interval_ parameter)*(0.1) sec. wdt_interval_parameter: { Valid Range: 0-15} IEEE Standard / Network topology: Fiber 10Gigabit Ethernet, 10GBASE-LR (1310nM LAN PHY) Data Transfer Rate: GBd Cables and Operating distance: Single- Mode: 10000m at 9um PCI Express Card Type: X8 Lane PCI Express Voltage: +12V ± 8% PCI Connector: Gold Finger - X8 Lane Controller: Intel 82599ES Holder: Metal Bracket I/O: LC Weight: 200g (7.055oz) Power Consumption: 6.6 W, 0.55 A at 12V: Typical all ports operate at 10Gb/s, (Normal Mode) W, 0.51 A at 12V: Typical Bypass Mode W, 0.53 A at 12V: Typical No link at all ports Optical Output Power: Normal Mode (Bypass Off): Minimum: -5.2 dbm Optical Receive Sensitivity: Normal Mode (Bypass Off) Maximum: dbm Insertion Loss: Bypass Mode: Insertion loss (Optical Power attenuation between TX to RX) (LC- fiber- switch- LC) Maximum 0.5 db LEDs: (2) LED per port Link: Turns on Blue on 10G link. ACT: Blinks on activity (green). Bi-color LED per Bypass pair: BYPASS: Turns on Green on Bypass Disconnect : Turns on Yellow on Disconnect Normal: Off LEDs location: LEDs are located on the PCB, visible via holes in the metal bracket holder Connector: (2) LC 16

17 The quad port Gigabit Ethernet bypass NIC cards [NIC-S400-4xGigE-LX-Fiber / NIC-S200-4xGigE-LX-Fiber] are PCIe x4 network adapters containing four fiber Gigabit interfaces, based on a single chip, non-bridged GBE controller. Key Features Fiber Gigabit Ethernet 1000Base-SX:: Independently Fiber Gigabit Ethernet channel/s support Gigabit Ethernet 1000Base-SX. Small Form Factor (SFF) LC Connectors. WDT Interval (Software Programmable): 3,276,800 msec (3,276.8 Sec): Maximum 100 msec ( 0.1 Sec) : Minimum WDT Interval = (2^wdt_interval_parameter)*(0.1) sec. wdt_interval_parameter: { Valid Range: 0-15} IEEE Standard / Network topology: Fiber Gigabit Ethernet, 1000Base-SX (850nM) Full duplex / Simplex: Support both Simplex & Full duplex operation in all operating speeds Auto negotiation: Auto-negotiation between Full duplex and simplex operations and between 10Mb/s 100Mb/s speeds and duplex 1000Mb/s. Data Transfer Rate: 2000Mbit/s in full duplex mode per port Cables and Operating distance: Multimode fiber - 137m maximum at 62.5 um * Technical Specifications Interface Standard: PCI-Express Base Specification Revision 2.1 (5GT/s) Board Size: mm X mm (6.60 X ) PCI Express Card Type: X4 Lane PCI Express Voltage: +3.3V +-9%, +12V +- 8% PCI Connector: Gold Finger - X4 Lane Controller: Intel i350am4 Holder: Metal Bracket I/O: LC Weight: 330g (11.641oz) Power Consumption: 0.40A, 4.8W at 12V: Typical all ports operate at 1000Mb/s. 0.40A, 4.8W at 12V: Typical No link at all ports. 0.38A, 4.56W at 12V: Bypass Mode. 0.38A, 4.56W at 12V: Disconnect Mode. LEDs: (1) LED per port Link/ACT: Blinks on activity (green). Turns on link (green). Bi-color LED per Bypass pair: BYPASS: Turns on Green on Bypass Disconnect : Turns on Yellow on Disconnect Normal: Off LEDs location: LEDs are located on the PCB, visible via holes in the metal bracket holder Connector: (4) LC *Theoretical Distance Defined as half a distance as stated by the IEEE standard 17

18 Install an option card into Slot 1 or 2 The S500 Series expansion slots 1 and 2 supports low-profile cards which can be accessed without the removal of the PCIe expansion module. ALWAYS observe proper electrostatic discharge (ESD) conventions. Attach an ESD protective wrist strap to your wrist and to the chassis. Ensure that the appliance is on an ESD-safe work surface or ground the unit appropriately. Symantec does not assume responsibility or liability for damage resulting from ESD. 1. Unplug the appliance power cords. 2. Open the appliance center cover. 3. Remove the appliance rear cover panel. 4. Unlock the PCIe support latch. 5. Remove the PCIe slot cover by lifting straight up from the appliance. 6. Insert the option card by holding the edges of the card and gently inserting into the slot. It might be necessary to lightly rock the option card into position. Verify that the PCIe card has been fully seated and is aligned with the chassis. 18

19 7. Lock the securing latch. Verify that it is fully closed and that the option card is secured. 8. Reinstall the appliance s center and rear panels. 9. Reconnect the network cabling as necessary for your deployment. 10. Reconnect the power cords. 11. Verify that you have correctly installed the option card. 19

20 Install an option card into Slot 3 or 4 The S500 Series is equipped with a PCIe expansion module that houses four PCIe cards - two full-height and two low-profile cards. Slots 3 and 4 are the only available slots which can accept a full-length card. ALWAYS observe proper electrostatic discharge (ESD) conventions. Attach an ESD protective wrist strap to your wrist and to the chassis. Ensure that the appliance is on an ESD-safe work surface or ground the unit appropriately. Symantec does not assume responsibility or liability for damage resulting from ESD. 1. Unplug the appliance power cords. 2. Open the appliance center cover. 3. Remove the appliance rear cover panel. 4. Remove the PCIe expansion module and flip over the to access the slots. 5. Unlock the blue PCIe support latches. 6. Remove the expansion slot cover by pressing the release button and then pulling out the cover from the side. Set the expansion slot cover aside in a safe location for future use 20

21 7. Insert the option card by holding the edges of the card and gently inserting into the slot. It might be necessary to lightly rock the option card into position. Verify that the PCIe card notch mates with the raised tab on the chassis and secure into place. 21

22 8. Lock the securing latches. Verify that it is fully closed and that the option card is secured. 22

23 9. Reinstall the PCIe expansion module into the chassis. 10. Reinstall the appliance s center and rear panels. 11. Reconnect the network cabling as necessary for your deployment. 12. Reconnect the power cords. 13. Verify that you have correctly installed the option card. 23

24 Install an option card into Slot 5 or 6 The S500 Series is equipped with a PCIe expansion module that houses four PCIe cards - two full-height and two low-profile cards. Slots can only accept low-profile cards. ALWAYS observe proper electrostatic discharge (ESD) conventions. Attach an ESD protective wrist strap to your wrist and to the chassis. Ensure that the appliance is on an ESD-safe work surface or ground the unit appropriately. Symantec does not assume responsibility or liability for damage resulting from ESD. 1. Unplug the appliance power cords. 2. Open the appliance center cover. 3. Remove the appliance rear cover panel. 4. Remove the PCIe expansion module and flip over the to access the slots. 5. Unlock the blue PCIe support latches. 6. Remove the expansion slot cover by pressing the release button and then pulling out the cover from the side. Set the expansion slot cover aside in a safe location for future use 24

25 7. Insert the option card by holding the edges of the card and gently inserting into the slot. It might be necessary to lightly rock the option card into position. Verify that the PCIe card notch mates with the raised tab on the chassis and secure into place. 8. Lock the securing latches. Verify that it is fully closed and that the option card is secured. 25

26 9. Reinstall the PCIe expansion module into the chassis. 10. Reinstall the appliance s center and rear panels. 11. Reconnect the network cabling as necessary for your deployment. 12. Reconnect the power cords. 13. Verify that you have correctly installed the option card. 26

27 Install an option card into Slot 7 The S500 Series is equipped with a PCIe expansion module that houses four PCIe cards - two full-height and two low-profile cards. The S500 Series also come with three low-profile expansion slots directly on the motherboard. These slots can be accessed without the removal of the PCIe expansion module. ALWAYS observe proper electrostatic discharge (ESD) conventions. Attach an ESD protective wrist strap to your wrist and to the chassis. Ensure that the appliance is on an ESD-safe work surface or ground the unit appropriately. Blue Coat does not assume responsibility or liability for damage resulting from ESD. 1. Unplug the appliance power cords. 2. Open the appliance center cover. 3. Remove the appliance rear cover panel. 4. Unlock the PCIe support latch. 5. Remove the PCIe slot cover by lifting straight up from the appliance. 6. Insert the option card by holding the edges of the card and gently inserting into the slot. It might be necessary to lightly rock the option card into position. Verify that the PCIe card has been fully seated and is aligned with the chassis. 7. Lock the securing latch. Verify that it is fully closed and that the option card is secured. 27

28 8. Reinstall the appliance s center and rear panels. 9. Reconnect the network cabling as necessary for your deployment. 10. Reconnect the power cords. 11. Verify that you have correctly installed the option card. 28

29 Open the S500 Series Center Cover The S500 Series center cover protects and houses the system fan units and provides further access to the appliance components. ALWAYS observe proper electrostatic discharge (ESD) conventions. Attach an ESD protective wrist strap to your wrist and to the chassis. Ensure that the appliance is on an ESD-safe work surface or ground the unit appropriately. Blue Coat does not assume responsibility or liability for damage resulting from ESD. 1. Remove or extend the appliance out of the rack to provide ample room for system access. 2. Simultaneously pull the locking tabs on both sides of the chassis towards the front and flip the cover over. Let the cover rest on top of the chassis. 29

30 Remove the S500 Series Rear Cover The S500 Series rear cover protects and provides access to the primary system components, such as the DIMMs, CPUs, option cards, etc. You must remove this panel to access the option cards as well as the SSD image storage devices. You cannot remove the rear cover without first opening the center cover. ALWAYS observe proper electrostatic discharge (ESD) conventions. Attach an ESD protective wrist strap to your wrist and to the chassis. Ensure that the appliance is on an ESD-safe work surface or ground the unit appropriately. Blue Coat does not assume responsibility or liability for damage resulting from ESD. 1. Unlock the rear cover by lifting the latch. 2. Push the rear cover towards the rear of the appliance then lift to remove the cover. Set the rear cover aside at a safe location. 30

31 Remove the S500 Series PCIe Expansion Module The S500 Series is equipped with a PCIe expansion module that houses four PCIe cards - two full-height and two low-profile cards. The S500 Series also comes with three low-profile expansion slots directly on the motherboard. These slots can be accessed without the removal of the PCIe expansion module. ALWAYS observe proper electrostatic discharge (ESD) conventions. Attach an ESD protective wrist strap to your wrist and to the appliance chassis. Ensure that the appliance is on an ESD-safe work surface or ground the unit. Blue Coat does not assume responsibility or liability for damage resulting from ESD. 1. Pull the release latch to unlock the module then lift the handle to unseat the module. 2. Lift the PCIe expansion module by the handle pull straight up and remove from the appliance. 31

32 Install the S500 Series PCIe Expansion Module The S500 Series is equipped with a PCIe expansion module that houses four PCIe cards - two full-height and two low-profile cards. The S500 Series also come with three low-profile expansion slots directly on the motherboard. These slots can be accessed without the removal of the PCIe expansion module. ALWAYS observe proper electrostatic discharge (ESD) conventions. Attach an ESD protective wrist strap to your wrist and to the chassis. Ensure that the appliance is on an ESD-safe work surface or ground the unit appropriately. Blue Coat does not assume responsibility or liability for damage resulting from ESD. 1. Align the PCIe expansion module with the posts on the chassis and press down. The module handle automatically lowers as it is being seated into place. 2. Lock the PCIe module in place by pressing down on the handle the rest of the way while pressing on the four corners of the module. Verify that the module is flat and aligned with the rest of the adjoining chassis structures. 32