250 mm 1 m. Name Sensing distance Model Quantity Remarks 250 mm E39-R6 1 Supplied with the product. Reflectors 1 m [250 mm] * E39-R

Transcription

1 Transparent Bottle Sensor ES-CR62/67 CSM_ES-CR62_67_DS_E Ideal for Detecting Transparent Glass and Plastic Containers Reliably detects narrow 5-mm gaps between bottles (When using the E9-R6). Significantly higher S/N ratio makes detection more reliable for various transparent containers. Be sure to read Safety Precautions on page 5. Ordering Information Sensors (Refer to Dimensions on page 6.) Sensing method Appearance Connection method Sensing distance E9-R6 E9-R Model Red light Retro-reflective Pre-wired (2M) Standard M2 Connector 25 mm m [25 mm] * ES-CR62 2M ES-CR67 * Values in parentheses indicate the minimum required distance between the Sensor and. Accessories (Order Separately) s (Refer to Dimensions on E9-L/F9-L/E9-S/E9-R.) Name Sensing distance Model Quantity Remarks 25 mm E9-R6 Supplied with the product. s m [25 mm] * E9-R --- * Values in parentheses indicate the minimum required distance between the Sensor and. Mounting Brackets (Refer to Dimensions on E9-L/F9-L/E9-S/E9-R.) Appearance Model Quantity Remarks E9-L Supplied with the product. E9-L Note: Refer to Mounting Brackets on E9-L/F9-L/E9-S/E9-R for details.

2 ES-CR62/67 Sensor I/O Connectors (M2) (Refer to Dimensions on S2) Cable Appearance Cable type Model 2 m S2F-D2-DC-A Straight 5 m S2F-D2-GC-A Standard cable -wire 2 m S2F-D22-DC-A L-shape 5 m S2F-D22-GC-A Note: For details on Sensor I/O Connectors and cables such as vibration-proof robot cables, refer to Introduction to Sensor I/O Connectors. Ratings and Specifications Sensor type Retro-reflective Models (M.S.R. function) Item Model ES-CR62 ES-CR67 Sensing distance 25 mm (When using the E9-R6), m (25 mm)* (When using the E9-R) Standard sensing object -mm dia. 5 mm glass tube (thickness:.8 mm) Directional angle 2 to 6 source (wavelength) Red LED (65 nm) Power supply voltage to VDC, ripple (p-p): % max. Current consumption ma max. Control output power supply voltage: VDC max., current: ma max. (Residual voltage: NPN output.2 V max., PNP output 2 V max.), Open collector model (NPN/PNP selectable), - / Dark- selectable Protection circuits Response time Sensitivity adjustment Ambient illuminance (Receiver side) Ambient temperature range Ambient humidity range Insulation resistance Dielectric strength Vibration resistance Shock resistance Degree of protection short-circuit protection, Reverse polarity protection, Mutual interference prevention or reset: ms max. 2-turn endless adjuster (with ) Incandescent lamp: 5, lx max., Sunlight:, lx max. Operating: 25 C to 55 C, Storage: C to 7 C (with no icing or condensation) Operating: 5% to 85%, Storage: 5% to 95% (with no condensation) MΩ min. at 5 VDC, VAC at 5/6 Hz for minute Destruction: to 2, Hz,.5-mm double amplitude or m/s 2 for.5 hrs each in,, and Z directions Destruction: m/s 2 times each in,, and Z directions IEC 529 IP67 (in-house standards: oil-resistant) NEMA 6P (restricted to indoor use) *2 *. Values in parentheses indicate the minimum required distance between the Sensor and. *2. NEMA (National Electrical Manufacturers Association) Standard IEC 529 IP67 NEMA 6P (restricted to indoor use) *2 Connection method Pre-wired (standard length: 2 m) Standard connector Weight (packed state) Approx. 5 g Approx. 8 g Material Accessories Case Lens Display operation panel Mounting Brackets Zinc die-cast Methacrylic resin Polyethyl sulfon Stainless steel (SUS) Clamps (with screws), Adjustment driver, Instruction manual, Reflective Plate 2

3 Set distance (mm) Set distance (mm) Engineering Data (Typical) ES-CR62/67 Parallel Operating Range ES-CR62/67 + E9-R6 (Supplied ) (Vertical Direction) (Horizontal Direction) E9-R6 Set distance (mm) E9-R Set distance (mm) Set distance (mm) 8 ES-CR62/67 + E9-R (Vertical Direction) (Horizontal Direction) E9-R Set distance (mm) E9-R Set distance (m) Set distance (m)

4 I/O Circuit Diagrams ES-CR62/67 NPN Model mode Timing charts selector circuit ES-CR62 ES-CR67 - Dark- (Between brown and (Between brown and L side (LIGHT ) D side (DARK ) Stability (green) Photoelectric Sensor main circuit PNP output NPN and PNP output selector NPN output Connector Pin Arrangement 2 Note: Pin 2 is not used. * Brown to VDC Black Blue * Set the selector switch to the NPN side. current Control output V PNP Model mode Timing charts selector circuit ES-CR62 ES-CR67 - Dark- (Between blue and (Between blue and L side (LIGHT ) D side (DARK ) Stability (green) Photoelectric Sensor Main Circuit PNP output NPN and PNP output selector NPN output Connector Pin Arrangement 2 Note: Pin 2 is not used. * Brown to VDC Black Blue * Set the selector switch to the PNP side. Control output current V Plug (Sensor I/O Connector) 2 Terminal No. 2 S2F-D2-DC-A Brown Blue Black Classification Wire color Connector pin No. Application Brown Power supply (+V) DC Blue Power supply ( V) Black Note: Pin 2 is not used. Refer to Introduction to Sensor I/O connectors for details. Nomenclature Stability (green) selector * S PNP NPN D L SENS L Min Max Sensitivity adjuster selector * * Use the output selector to select the type of output, NPN or PNP.

5 Safety Precautions ES-CR62/67 Refer to Warranty and Limitations of Liability. This product is not designed or rated for ensuring safety of persons either directly or indirectly. Do not use it for such purposes. Do not use the product in atmospheres or environments that exceed product ratings. Designing Fuzzy Mutual Interference Prevention Function If reflective Photoelectric Sensors are installed side by side, each reflective Photoelectric Sensor may be influenced by the light emitted from the other Photoelectric Sensors. The fuzzy mutual interference prevention function of the ES- CR62/67 enables the ES-CR62/67 to monitor any light interference for a certain period before the ES-CR62/67 starts emitting light so that the ES-CR62/67 can retrieve the intensity and frequency of the light interference as data. Using this data, the ES-CR62/67 estimates with fuzzy inference the risk of the malfunctioning of the ES-CR62/67 and controls the timing of the ES-CR62/67 s light emission. When the risk is low: The ES-CR62/67 waits until there is no light interference and emits light. interference Emission pattern WARNING Precautions for Correct Use When the risk is high: The ES-CR62/67 emits light between each light interference moment. interference Emission pattern Bottles In some cases, factors such as the shape of a bottle prevent stable detection. Please confirm that detection takes place correctly before use. Mounting Mounting the Sensor When mounting the ES-CR62/67, do not hit the ES-CR62/67 with a hammer, or the ES-CR62/67 will loose watertightness. Use M screws to mount the ES-CR62/67. The tightening torque of each screw must be.8 N m maximum. (When using the mounting bracket) To set the sensor on the mechanical axis, use the optical axis locking holes. When it is not possible to mount on the mechanical shift, move the photoelectric switch vertically or horizontally so that it is located in the center of the area illuminated by the incident light lamp. Verify that the stability lamp is on. (Direct mounting) Install the photoelectric sensor as shown in the following diagram. M Tighten M screw M hole M hole Two,.5-dia. through holes Tighten M screw 2-M M hole M hole Adjusting adjustment Adjust the optical axis of the clamp to the direction of sensing object approach. The optical axis of the photoelectric sensor is the same as the mounting axis of the clamp, enabling easy adjustment. About the optical axis locking hole By fitting screws into the optical axis locking holes, the mounting bracket is set onto the mounting shaft of the mounting bracket. M Wiring Cable The ES-CR62/67 uses an oil-resistive cable to ensure oil resistivity. Avoid repeated bending of the cable. Do not allow the cable to be bent to a radius of less than 25 mm. Avoiding Malfunctions When using a photoelectric sensor with an inverter or sub-motor, be sure to connect FG (frame ground terminal) and G (ground terminal). If not connected, errors may result. Four, M optical axis lock holes Mounting axis 5

6 Dimensions Sensors Retro-reflective Models Pre-wired ES-CR62 ES-CR62/67 (Unit: mm) Tolerance class IT6 applies to dimensions in this datasheet unless otherwise specified. With Mounting Bracket Attached Lens (..5) -dia. vinyl-insulated round cable with conductors (Conductor cross section:.2 mm 2 ; Insulator diameter:.2 mm), Standard length: 2 m Receiver, Emitter Mounting Holes Two, M 25. Stability (green) Stainless steel (SUS) (A)* M 5 Two, M 2 * Mounting Bracket can be attached to side A. 2.2 ().5 Standard Connector ES-CR67 With Mounting Bracket Attached Lens (..5) M Receiver, Emitter Mounting Holes Two, M 25. Stability (green) Stainless steel (SUS) (A)* M 5 Two, M 2 * Mounting Bracket can be attached to side A. 2.2 ().5 Accessories (Order Separately) s Refer to Dimensions on E9-L/F9-L/E9-S/E9-R. Mounting Brackets Refer to DImensions on E9-L/F9-L/E9-S/E9-R. Sensor I/O Connectors Refer to Introduction to Sensor I/O connectors for details. 6

7 Read and Understand This Catalog Please read and understand this catalog before purchasing the products. Please consult your OMR representative if you have any questions or comments. Warranty and Limitations of Liability WARRANT OMR's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMR. OMR MAKES NO WARRANT OR REPRESENTATI, EPRESS OR IMPLIED, REGARDING N-INFRINGEMENT, MERCHANTABILIT, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. AN BUER OR USER ACKNOWLEDGES THAT THE BUER OR USER ALE HAS DETERMINED THAT THE PRODUCTS WILL SUITABL MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMR DISCLAIMS ALL OTHER WARRANTIES, EPRESS OR IMPLIED. LIMITATIS OF LIABILIT OMR SHALL NOT BE RESPSIBLE FOR SPECIAL, INDIRECT, OR CSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS IN AN WA CNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED CTRACT, WARRANT, NEGLIGENCE, OR STRICT LIABILIT. In no event shall the responsibility of OMR for any act exceed the individual price of the product on which liability is asserted. IN NO EVENT SHALL OMR BE RESPSIBLE FOR WARRANT, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS OMR'S ANALSIS CFIRMS THAT THE PRODUCTS WERE PROPERL HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CTAMINATI, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATI OR REPAIR. Application Considerations SUITABILIT FOR USE OMR shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's application or use of the products. At the customer's request, OMR will provide applicable third party certification documents identifying ratings and limitations of use that apply to the products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product, machine, system, or other application or use. The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible uses of the products, nor is it intended to imply that the uses listed may be suitable for the products: Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. Systems, machines, and equipment that could present a risk to life or property. Please know and observe all prohibitions of use applicable to the products. NEVER USE THE PRODUCTS FOR AN APPLICATI INVOLVING SERIOUS RISK TO LIFE OR PROPERT WITHOUT ENSURING THAT THE SSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMR PRODUCTS ARE PROPERL RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SSTEM. PROGRAMMABLE PRODUCTS OMR shall not be responsible for the user's programming of a programmable product, or any consequence thereof. Disclaimers CHANGE IN SPECIFICATIS Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or establish key specifications for your application on your request. Please consult with your OMR representative at any time to confirm actual specifications of purchased products. DIMENSIS AND WEIGHTS Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown. PERFORMANCE DATA Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of OMR s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMR Warranty and Limitations of Liability. ERRORS AND OMISSIS The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical, or proofreading errors, or omissions. OMR Corporation Industrial Automation Company 8. In the interest of product improvement, specifications are subject to change without notice. (c)copyright OMR Corporation 8 All Right Reserved.