Controller 3000, dependent on reader technology and site configuration. All I/O functionality is provided on the Controller 3000.

Transcription

1 The features described in this data sheet are being progressively added to the CardaxFT Controller during 2002/2003. Please contact Cardax f further infmation. Cardax FT Controller 3000 Cardax FT Controller 3000 The Cardax FT Controller 3000 is a cost effective, intelligent field controller, with integrated I/O functionality, f Cardax FT systems. Linking with the Cardax FT Command Centre f Series 3 Series 5, the Cardax FT Controller 3000 integrates I/O functionality and do control. Cardax FT Controller 3000 The Cardax FT Controller 3000 is a key integrated component f Cardax FT security systems. It is an intelligent controller incpating a 32 bit Intel microprocess. It makes all the access control decisions in the system. The structure of Cardax FT systems is very flexible. F example, a single alarm relay can be switched in response to several alarm conditions detected by a number of Controllers. Conversely, an input may be used to control a number of outputs, on different Controllers, such as lighting and air conditioning. With built in connectivity, the Cardax FT Controller 3000 provides a cost-effective approach to engineering a Cardax FT Series 3 Series 5 system. Up to 4 8 dos can be controlled with the Controller 3000, dependent on reader technology and site configuration. All I/O functionality is provided on the Controller Integrating Cardax Readers The Cardax FT Controller 3000 is capable of suppting up to 8 dos with Cardax readers, depending on the required site configuration. Refer to the Configuration Table f me details. The Controller 3000 suppts the following Cardax do readers: Cardax Prox (125, TIRIS, Mifare) Cardax Prox Plus (125, TIRIS, Mifare) Cardax Prox LR (TIRIS) Cardax Swipe (Magstripe) Cardax Swipe Plus (Magstripe) Integrating Third Party Readers The Cardax FT Controller 3000 is capable of suppting 4 dos with Wiegand fmat readers. Refer to the Configuration Table f me details. Moniting and Controlling Inputs and Outputs The Controller 3000 contains inputs and outputs, which can be used f do moniting and control, f general I/O functions. The Controller 3000 monits and repts the state of the balanced inputs, and makes decisions to switch output relays, if required. Inputs The Controller 3000 has 16 4-state balanced inputs. The four states monited (using two 4k7 Ohm resists) are: Open Closed Sht Circuit (Tamper) Open Circuit (Tamper) The inputs on the Controller 3000 can be used to monit: Access controlled dos Intruder detection (Passive Infra-Red detects PIRs)

2 Uncontrolled dos Equipment alarms Any other devices that provide a clean contact. Outputs The Controller 3000 contains 8 relay outputs, primarily f use as do control relays. Relays not required f this function may be used as: Alarm outputs, e.g. to activate sirens Logic activated outputs, e.g. to switch on air conditioning Time activated outputs, e.g. to switch on lighting. Distributed Intelligence and Data Stage The Cardax FT Controller 3000 stes security parameters and a resident cardholder database to enable it to carry out access control and security functions. The resident cardholder database stes access data f cardholders who will access the areas associated with that Controller It enables the Controller 3000 to make access control decisions instantaneously. Access control infmation f cardholders who are not included in the resident cardholder database is requested from the Cardax FT Command Centre when required, and then sted in the Controller 3000 database. The distributed intelligence suppted by the Controller 3000 enables it to operate independently from the Cardax FT Command Centre. This means access control f resident cardholders and other security functions will continue if communications fail between the Command Centre and the Controller The impact on cardholders will thus be minimised. All events and alarms are date and time stamped befe being sent to the Cardax FT Command Centre Server. Each Controller 3000 is capable of buffering events should communications with the Command Centre fail. The Controller 3000 will transfer the buffered events to the Command Centre automatically when communications are re-established. The number of cardholder recds is set at 30,000 and the size of the event buffer at 5,000 events. Communications The communications between the Cardax FT Controller 3000 and the Cardax FT Command Centre use TCP/IP, a wld standard netwk and Internet transmission protocol, over an Ethernet netwk. The Controller 3000 provides a standard 10BaseT connection point. Remote Cardax FT Controller 3000s can be connected to the system via a TCP/IP Wide Area Netwk (WAN). Dial-Up Dial-up enables the Controller 3000 to be located remotely enabling the Controller 3000 to transmit infmation: At scheduled times When their event buffers are becoming full In response to certain events. Likewise, the Cardax FT Command Centre can be programmed to dial a Controller 3000 at scheduled times, when an operat initiates a request. Dial-up can also occur via an ISP, improving netwk security and reducing communication costs. Configuration Table CARDAX Readers (8 total) Input Moniting (16 total) Do Control Relays (8 total) Entry Exit Do Do Request Spare Do Spare Closed Locked to Exit Inputs Outputs 4 do control n/a do control (Request to Exit) * 8 do control (free handle exit) WIEGAND Readers (4 total) Input Moniting (16 total) Do Control Relays (8 total) Entry Exit Do Do Request Spare Do Spare Closed Locked to Exit Inputs Outputs 4 do control * 4 do control (free handle exit) * Note: If request to exit is not monited, then fced do moniting must also be disabled.

3 Key Features of the Cardax FT Controller 3000 Front Optical Tamper Detect (Cabinet open) RS485 Pt Run LED Power In Auxiliary RS232 Pt 10 BaseT Ethernet Pt Run/Diagnostic Indicats Power Supply Indicat (visible through cabinet do) Power Out Relay Output Connects Balanced Inputs Reader Connections Software Upgrades The Cardax FT Controller 3000 can be enhanced in the future via software upgrades. These software upgrades can be implemented over the netwk through Cardax FT Command Centre. Looking to the future, this will enable new features and functionality to be quickly and easily installed. The following are examples of situations where future software upgrades to the Controller 3000 would be downloaded over the netwk: Enhanced functionality Specialised logic control functions (PLC) Expansion board interface board suppt. Data Security All data over the netwk between the Cardax FT Controller 3000 and the Cardax FT Command Centre Server is encrypted to 40-bit, using Secure Sockets Layer (SSL) technology. The standard is similar to technology used to secure Internet banking transactions. High-level (168-bit) encryption is an optional licensed feature. Intruder Alarms The Controller 3000 provides sophisticated intruder alarm management, making separate intruder alarm systems superfluous. Entry and exit delays can be configured to give the cardholder time to enter leave the premises. Full event details, including the cardholder s name, are recded f set/unset operations at Cardax FT Command Centre. Setting and unsetting of alarms can also be implemented accding to a time schedule. A relay output may be used to indicate the set/unset status of a particular alarm zone. Lift Control The Cardax FT Controller 3000 provides lift access control using the I/O functionality provided. Card readers can be installed in lift cars to provide restricted access to flos. When a Cardax Prox Plus reader is installed, the cardholder can be prompted to enter their PIN befe access is granted. Flos may be unlocked (i.e. the lift flo select button enabled) on a time schedule. The Controller s flexible design enables it to be configured f lift control. Typically each lift car requires one card reader and one relay output f each flo select button. If destination repting is required then one input is needed f each flo select button in each lift car. The Controller 3000 has been designed to suppt a high level interface f lift control. In this case, the number of lift cars and lift shafts is limited only by the length of the wiring to the card readers and not the input/output capacity. High-level lift control will be developed as required (please contact Cardax f me infmation). Power Supply The Cardax FT Controller 3000 runs on 13.6V DC ±15% allowing a standard battery backed 12V power supply to be used. The system monits the power supply f power low, power high, and power fail. It is recommended that installers attach a backup power supply to the Controller 3000 so it can continue to operate f at least 24 hours in the event of a mains supply failure.

4 Cardax FT Cabinet (with Cardax FT Controller 3000) The backup power supply can be monited by using inputs on an alternative Controller Clock The Cardax FT Controller 3000 contains its own super-capacit backed realtime clock. The clock is synchronised with the Command Centre at least once per hour. Managing Different Time Zones and Daylight Saving When the system is being configured, each Cardax FT Controller 3000 is assigned an international time zone, relative to Co-dinated Universal Time (UTC). This includes daylight savings settings. The system recds the local time an event was registered at the Controller 3000 and the time it was logged at the Command Centre Server. Cardax FT Cabinet The Cardax FT Cabinet is a secure enclosure f the Cardax FT Controller It provides cost-effective housing and includes many features designed to make installation and servicing easier. The design of the Cardax FT Cabinet enables several Cabinets to be installed side by side, neatly fitting together. Each Cabinet has a lockable lid that can be installed, on site, to hinge from either side. When the Printed Circuit Board (PCB) is installed in the Cardax FT Cabinet, optical tamper protection is provided. The front optical tamper detect will sense when the Cabinet do is opened. The rear optical tamper detect will sense if the Cabinet is being removed from the wall. Manufactured from a strong ABS alloy, the Cardax FT Cabinet has a UL94 flame rating of V0. The Cardax FT Cabinet can house one Cardax FT Controller The Controller 3000 must be mounted in a Cardax FT Cabinet following the directions in the installation instructions to comply with international emission standards such as C-Tick, FCC and CE. Connectivity Diagram Ethernet connection from Cardax FT Command Centre 16 Inputs Cardax FT Controller Relay Outputs Power 13.6V DC ± 15% 8 Cardax Readers 4 Wiegand Readers

5 November 2002 TECHNICAL SPECIFICATIONS Cardax FT Controller 3000 Power Supply Voltage 13.6 V DC ± 15% Current (without relays operated) 290 ma Current (all relays operated) 610 ma The above currents exclude external devices such as readers and alarm sounders Number of Pts RJ45 Ethernet connection (10BaseT) 1 RS485 (f future developments) 1 RS232 1 Communications Cable Specifications Reader pts f Cardax readers 8 Reader pts f Wiegand fmat readers 4 Cardax FT Series 3 Command Centre Cardax FT Series 5 Command Centre Cardax readers Wiegand readers To Cardax FT Series 3 Command Centre Cardax FT Series 5 Command Centre Cardax readers Wiegand readers 10 Megabit /Ethernet TCP/IP Cardax propriety up to 360 bit Ethernet 10BaseT 4 wire 6 wire Max Cable Lengths: Cardax readers 200m Wiegand readers See manufacturers specifications Inputs/Outputs Inputs (4-state balanced) 16 Relay outputs 8 Relay Specifications Resistive load 3 Amps at 24V DC/AC Inductive Load 1 Amp at 24V DC/AC Maximum Number of controlled dos per Cardax FT Controller Data Stage per Cardax FT Controller 3000 Max. number of Access Zones 16 Max. number of Alarm Zones 256 Capacity of unprocessed alarms buffer 5,000 Max. number of Access Groups 2,000 Max. number of Time Schedules 1,000 Number of cardholders 30,000 Number of events 5,000 Access Criteria Changes Access control zones 100 per schedule Lift level changes 100 schedule Alarm zone changes 100 schedule Housing Cardax FT Cabinet Height Width Depth 280 mm 280 mm 94 mm Weight (nmal) PCB and Cabinet 1862 grams Environmental Data Temperature range -10 to +55 C Humidity 95% non-condensing Fire Resistance Flame rating of Cabinet UL94 / V0 Compliance Standards The Cardax FT Controller 3000 complies with C-Tick, CE and FCC approvals. Compliance with other international standards will be proven during 2002/2003. Please contact Cardax f the latest list of approvals. All Cardax FT products must be installed in accdance with the Installation Notes to comply with international standards.

6 Whilst every efft has been made to ensure accuracy, neither Cardax (International) Limited n any employee of the company, shall be liable on any ground whatsoever to any party in respect of decisions actions they may make as a result of using this infmation. In accdance with the Cardax policy of continuing development, design and specifications are subject to change without notice. Developed and manufactured by Cardax (International) Limited, an ISO 9001:2000 certified supplier. Cardax is a registered trademark of Cardax (International) Limited. Cardax (International) Limited is a subsidiary of Gallagher Group Limited. Copyright Cardax (International) Limited All rights reserved. Patents pending. Cardax (International) Ltd Kahikatea Drive Private Bag 3026 Hamilton New Zealand Telephone Fax cdxsales@cardax.com Cardax Offices are located in: Australia China New Zealand South Africa Thailand United Kingdom 6J /02