PCD7.LRxx BACnet Room Controller

Transcription

1 WM 0 C+ L WM C- V0 AO AO 0 AO UI UI UI UI C+ I WM 0 C+ L C- SERVICE 0 WM C- V0 AO AO 0 AO UI UI UI UI C+ I Saia PCD.C 0 WM 0 C+ L C- SERVICE 0 WM C- V0 AO AO 0 AO UI UI UI UI C+ C- SERVICE 0 I WM 0 C+ L C- SERVICE 0 WM C- V0 AO AO 0 AO UI UI UI UI C+ I PRODUCT DATA SHEET PP-00 EG0 PCD.LRxx BACnet Room Controller GEERAL The PCD.LRXX BACET Room Controllers family provide flexible, configurable, demand-led control that delivers tangible benefits to reduce energy spends and drives new levels of functionality and efficiency in today s buildings. The BACnet MS/TP-based room controllers includes a configurable application supporting fan coil unit, chilled and hot ceiling as well as radiator heating applications. It is even possible to handle a mix of these applications in one controller. Line voltage or VAC power supply and the flexible use of relays and triacs ( VAC or 0 VAC), VAC power supply for field devices, Sylk wall modules, and smart engineering and commissioning tools reduce the total installed cost. Fig.. PCD.LRxx (without optional covers) FEATURES Designed to control terminal units such as - and -pipe fan coil units, chilled and hot ceilings, hydronic heating, and a mix of these applications. Support for - stage fans, variable fan speed drives (VSDs), thermal, floating, proportional actuators, and -way valve actuators (see section Commissioning, pg. ). Auto Mac-addressing. Fast commissioning using plug-and-play solutions, pre-defined applications and state-of-the-art commissioning via the ROOMUP mobile application eliminating the need for two people when commissioning. Reduced number of sensors because sensors are shared across different applications. BACnet BTL -Listed as Advanced Application Controllers (B-AAC) rev.. Two housing dimensions and several different I/O versions to match your individual needs. Universal mounting options, including terminal covers and color-coded terminals. The 0 VAC models feature VAC aux. output voltage, allowing direct connection and powering of field devices Two-wire polarity-insensitive bus interface to connect to Honeywell Sylk wall modules. SYSTEM OVERVIEW BACnet IP Saia PCD PCD Saia PCD Saia PCD Saia PCD PCD.L-ROOMUP BACnet Wi-Fi ADAPTER PCD.LRL PCD.LRL PCD.LRL PCD.LRL Fig.. PCD.LRL Example Table. Overview of models Article number Housing Power supply Analogue outputs AOs Universal inputs UIs Relays Triacs (/0 VAC) Total no. of I/O VAC output for field devices and Triac outputs Comment PCD.LRL Large 0 VAC max 00 ma fixed terminals, except BACnet PCD.LRS Small 0 VAC max 00 ma MS/TP, Sylk and VAC power supply terminals which are PCD.LRS Small VAC max 00 ma removable

2 L C+ C- WM WM L WM V0 WM V0 V0 AO AO AO T0 AO T0 UI RC UI UI UI C+ I C+ C- I C- SERVICE SERVICE PCD.LRxx BACnet Room Controller PRODUCT DATA SHEET PP-00 EG0 DIMESIOS AD MOUTIG Housings The controller is available in two housing sizes, both conforming to IP0: PCD.LRL (large housing): W L H = mm and PCD.LRSx (small housing): W L H = mm See also Fig. and Fig.. IRM-RLC (BULK PACK, pcs.) PCD.LRx PCD.LRx... REMOVABLE TERMIALS Fig.. Large housing, with terminal protection covers, dimensions (in mm). 0 AO AO 0 AO AO UI LED UI 0 UI UI UI UI UI UI UI 0 UI 0. IRM-RSC (BULK PACK, pcs.) Fig.. PCD.LRL dimensions (in mm). PCD.LRSx PCD.LRSx. REMOVABLE TERMIALS.. 0 C+ C- 0 0 Fig.. Small housing, with terminal protection covers, dimensions (in mm). Fig.. PCD.LRSx dimensions (in mm) The unit is suitable for mounting on a standard rail, on walls, as well as in wiring cabinets or fuse boxes. Terminal Protection Covers for IP0 In the case of controllers mounted outside of a cabinet, before applying power to the device, Terminal Protection Covers (-pc. bulk packs, order no.: IRM-RLC for large housings and IRM-RSC for small housings) must be mounted so as to provide IP0. TERMIAL ASSIGMET General For a complete list of all terminals and a description of their functions, see Table and Table. Communication Interfaces All models of the controller features the following communication interfaces: A Sylk Bus interface for connection to TR0, TR0-CO, TR and TR-CO Wall Modules; A interface; An RJ- connector for connection of the BACnet WiFi Adapter.

3 PRODUCT DATA SHEET PP-00 EG0 PCD.LRxx BACnet Room Controller Table. PCD.LRSx Room Controller: Overview of terminals and functions term. printing function RS RS, L, 0-V power supply X ---,, V0 Removable -V power supply input --- X,, V0 Aux. output voltage ( VAC) for all triacs X --- Aux. term. for triac neutral wiring (internally connected with terminal ) X X Triac input voltage ( VAC / 0 VAC) for all triacs; triac-switched X X Triac-switched output X X Aux. term. for triac neutral wiring (internally connected with terminal ) X X Triac-switched output X X,, Output of Relay, Input for Relay type type,, Aux. terminals for relay neutral wiring X X,, Input for Relay, Output of Relay type type, I, Input for Relay, Output of Relay type type,, Input for Relay, Output of Relay type type 0, WM, WM Removable interface for Sylk Bus X X,,,, C+, C-, ot used Analog Output type type VAC power for field devices X X Ground for AOs X X AO Analog Output type type 0 AO Analog Output type type VAC power for field devices X X Ground for AOs X X AO Analog Output type type UI Universal Input X X Ground for UIs X X UI Universal Input X X UI Universal Input X X Ground for UIs X X UI Universal Input X X 0,, C+, C-, Removable interface and corresponding X X Relay output types: See Table. Universal input types: See Table. Analog output types: See Table Table. Relay output types and characteristics type (standard) type (high in-rush current) corresponding ROs of RSxx,, corresponding ROs of RLxx,, contact.o..o. min. load VAC, 0 ma VAC, 0 ma switching voltage range VAC VAC max. continuous load at 0 VAC (cos φ = ) A A max. continuous load at 0 VAC (cos φ = 0.) A A in-rush current (0 ms) A usage fan motor light switching and fan motor OTE: The max. sum load of all relay currents at the same time is A.

4 PCD.LRxx BACnet Room Controller PRODUCT DATA SHEET PP-00 EG0 Table. Analog output types and characteristics type type type output voltage 0 V output current 0 ma 0 ma 0 ma min. accuracy max. ripple accuracy at zero point ±0 mv ±0 mv 0 00 mv Table. Universal input types and characteristics pull-up voltage: V TCkΩ TC0kΩ dry contact (closed: res. < kω; open: res. > 0 kω; max. 0. Hz; pull-up voltage: V) fast binary (=counter) input (max. 0 Hz; pulse O = min. ms; pulse OFF = min. ms; closed: voltage < V; open: voltage > V; pull-up voltage: V) SetPoint and FanSpdSW (from PCD.Lx, Q.RCU-A-Txxx and T0x) UI, UI, UI, UI, UI, UI X X X X X X

5 PRODUCT DATA SHEET PP-00 EG0 PCD.LRxx BACnet Room Controller Table. PCD.RLxx Room Controllers: Overview of terminals and functions (by model) term. printing function RL, L, 0-V power supply X,, V0 Removable -V power supply input ---,, V0 Aux. output voltage ( VAC) for all triacs X Aux. terminal for triac neutral wiring (internally connected with terminals + ) X Triac input voltage ( VAC / 0 VAC) for all triacs; triac-switched X Triac-switched output X Aux. terminal for triac neutral wiring (internally connected with terminals + ) X Triac-switched output X T0 Triac-switched output X Aux. terminal for triac neutral wiring (internally connected with terminals + ) X T0 Triac-switched output X RC Triac-switched output ---,, Output of Relay, Input for Relay type Aux. terminal for relay neutral wiring X Aux. terminal for relay neutral wiring X 0,, Input for Relay, Output of Relay type, I, Input for Relay, Output of Relay type,, Input for Relay, Output of Relay type,,, C+, C-,, RS- Modbus interface, corr., + aux. power ( VAC ±0%, 0/0 Hz) 0, WM, WM Removable interface for Sylk Bus X Analog Output type Ground for AOs X AO Analog Output type VAC power for field devices X AO Analog Output --- Ground for AOs --- AO Analog Output --- VAC power for field devices AO Analog Output --- Ground for AOs --- AO Analog Output --- VAC power for field devices --- VAC power for field devices X LED Output to LED of PCD.L, Q.RCU-A-TSOx and T0C,E,F X Ground for UIs X UI Universal Input type UI Universal Input type Ground for UIs X 0 UI Universal Input type UI Universal Input type Ground for UIs X UI Universal Input type UI Universal Input type Ground for UIs X UI Universal Input --- UI Universal Input --- Ground for UIs --- UI Universal Input UI Universal Input --- Ground for UIs ---,, C+, C-, Removable interface and corresponding X ---

6 PCD.LRxx BACnet Room Controller PRODUCT DATA SHEET PP-00 EG0 TR Wall module PROP. COOL PROP. HEAT Variable speed 0- VDC V ROOMUP App on Smartphone BACnet WiFi Adapter Window contact Occupancy contact RJ PLUG 0 WM WM 0 0 AO AO AO UI UI UI UI C+ C- RJ ITERFACE,,, V0 I F* THERM. COOL ELECTR. REHEATER *OPTIOAL FUSE (TO PROTECT THE COTROLLER S ITEAL TRASFORMER, WHICH HAS OLY A O-RESETTABLE FUSE). L 0 VAC Fig.. PCD.LRS example wiring *OPTIOAL FUSE (TO PROTECT THE COTROLLER S ITEAL TRASFORMER, WHICH HAS OLY A O-RESETTABLE FUSE). Q.RCU-A-TSOF WALL MODULE COM TEMP SETP FA LED ROOMUP App on smartphone BACnet WiFi adapter WIDOW COTACT DEW POIT RJ PLUG 0 WM WM AO AO AO 0 AO AO 0 0 UI UI IU IU IU C+ C- LED UI UI IU IU IU RJ ITERFACE,,, L V0 T0 T0 0 I VAC OUTPUT THERM. FLOATIG ELECTR. TI RI HEAT COOL REHEATER FI -SPEED FA L 0 VAC F* L L LIE VOLTAGE Fig.. PCD.LRL example wiring

7 PRODUCT DATA SHEET PP-00 EG0 PCD.LRxx BACnet Room Controller ELECTRICAL DATA RL and RS (0 VAC) Power via terminals + : 0 VAC +% / %, 0/0 Hz. Max. power consumption (when unloaded): W. Max. power consumption (when loaded): W. The controller is unloaded when it has no external load. Thus, the only load on the controller is the inherent load ( W) of the electronics, themselves. The heat dissipation then amounts to W. The controller is loaded when besides the inherent load an additional sum load of max. 00 ma is applied to the VAC output terminals. The max. unloaded output voltage at terminals and is VAC (typically. VAC). RS ( VAC) Power via terminals +: VAC ±0%, 0/0 Hz. Max. current consumption (when unloaded): 00 ma. Max. current consumption (when loaded): 00 ma. The controller is unloaded when it has no external load. The heat dissipation then amounts to W. The controller is loaded when besides the inherent load (00 ma) an additional sum load of max. 00 ma is applied to the VAC output terminals. COMMISSIOIG Configurable Application All models are delivered with the configurable application already included in the controller. The configurable application has the advantage that it is proven and quickly commissioned using the ROOMUP commissioning tool available in the Google Playstore (URL: running on an Android Smart device with Android Version > V.. To activate the downloaded RoomUp app, it need to be ordered a RoomUp Licence-Key with ordering number PCD.L-ROOMUP. OTE: Before configuring, if as yet no WLA is present, the commissioning engineer will require a BACnet WiFi Adapter (order no.: BACA-A) to establish wireless communication between his Android Smart device and the controller. Example Application Types The configurable application supports the following application types: The FCU application type supports -, -, and -stage or variable-speed fan. It also supports water cooling, water heating (-pipe or -pipe), electric re-heating, and dx-cooling (incl. fan interlock). It supports PID and, optionally, cascade control as well as min. temperature limitation. This application type may be used in combination with other types (see following). The chilled/heated ceiling application type uses PID with dewpoint protection (-pipe or -pipe). It also supports -way valve on AO. The radiator heating application type uses PID and, optionally, min. temperature limitation. The underfloor heating application type uses PID and, optionally, max. temperature limitation. The intake air application type uses PID and, optionally, min. temperature limitation and air quality control. Those inputs/outputs not needed by the configurable application are available for use as free I/Os (like the I/Os of an I/O module) by the plant controller see also PCD.LRxx Room Controller Installation & Commissioning Instructions (PP-0). The use of different application types is limited by the number of I/Os supported by the given model.

8 PCD.LRxx BACnet Room Controller PRODUCT DATA SHEET PP-00 EG0 Supported Actuators The application supports a variety of actuators. Table. Supported actuators Supported actuators / Application Analog 0() V Floating PWM Stage Stage, Stage + -way valve 0 V FCU Cooling FCU Heating FCU DX-Cooling FCU E-Heating Ceiling Cooling Ceiling Heating Ceiling Switch over -way Cooling Ceiling Switch over -way Heating Ceiling Switch over -way O / OFF Radiator Heating Underfloor Heating Intake Air FreeAO FreeBO Supported Sensors A variety of sensors (e.g., room temperature sensors, supply temperature sensors, condensation switch, window sensors, occupancy sensors, and card readers, etc.) may be used to optimize control quality. Supported Operating Modes The application supports a variety of different operating modes (e.g., occupied, standby, unoccupied, building protection, fan automatic/manual). Master/Slave Functionality During configuration, the commissioning engineer can identify (e.g., using the ROOMUP configuration tool) which of the controllers located on a given bus are so-called Masters, and which are so-called Slaves. The commissioning engineer is not allowed to assign more than a single Master to each Slave; this is the only action which the commissioning engineer is required to perform. The Slave controller will inform its Master that it has been assigned to be its Slave. The given application in the Master controller defines how this group (consisting of the Master controller and its Slave controllers) reacts to sensor inputs. Examples: Activation of a window contact (indicating an opened window) will cause the application to stop heating/cooling. Each Master and each Slave needs to have its own ceiling cold water temperature sensor and its own condensation contact. Receipt of a condensation signal will stop cooling. Occupancy will be detected if one of the occupancy sensors detects occupancy. A key card will be detected if one of the key card sensors detects a key card. Occupancy override from one of the connected wall modules will trigger an occupancy override. The last setpoint change (temperature setpoint or fan speed setpoint) on one of the wall modules (TR0x / TRx) will define the setpoint (OTE: All TRx wall modules will show the actual settings used by the controllers). For such sensor values as temperature, CO, and humidity, the average value is used (thus improving system robustness against failures of a single sensor and having a better average value of the room.) The Master shares schedule, heat/cool mode, actuator positions, etc. with its Slave(s). Automatic MAC Addressing In contrast to many other MS/TP controllers, PCD.LRxx BACET Room Controllers features automatic MAC addressing. There is thus no need to manually set the MAC address.

9 PRODUCT DATA SHEET PP-00 EG0 PCD.LRxx BACnet Room Controller OPERATOR ITERFACES LEDs RJ- Connector for BACnet WiFi Adapter The controller features the following LEDs: T R T R! = DETECT = = = VAC = = = C+ = C- SMART- PHOE BACnet WiFi ADAPTER Fig.. Controller LEDs RJ PLUG Table. Description of LED behaviors symbol color function, description T yellow ot used R yellow ot used T yellow LED indicating transmission of communication signals via the interface R yellow LED indicating reception of communication signals via the interface. yellow Status LED indicating firmware problems, hardware problems, etc. green red Power LED indicating firmware problems, hardware problems, etc. ot used PCD.RLx (PCD.RSx) (0) C+ ITEAL COECTIOS () C- () RJ COECTOR,,, Fig.. RJ- interface and BACnet WiFi Adapter Service Button The controller s Service Button is used to trigger dedicated events. COMMUICATIO ITERFACES Interface The controller features an RS- interface (RLx: terminals,, and ; RSx: terminals 0,, and ) suitable for communication. The terminal block containing it is black. The cable length affects the baud rate. See Table. Table. Baud rate vs. max. cable length baud rate.,.,.,., and. kbps 00 m. kbps 00 m max. cable length (L) For information on wire gauge, max. permissible cable length, possible shielding and grounding requirements, and the max. number of devices which can be connected to a bus, refer to standard EIA-. CAUTIO It is permitted to connect only the BACnet WiFi Adapter to this RJ- connector. Do not connect IP! A BACnet WiFi Adapter can be connected to the controller s RJ- connector in order to establish wireless communication with an Android Smart device so that the application engineer can configure the controller (using the ROOMUP configuration tool). OTE: When the BACnet WiFi Adapter is connected to the controller s RJ- connection, it is powered by the controller. It is then prohibited to simultaneously power the BACnet WiFi Adapter via a wall adapter. When, on the other hand, the BACnet WiFi Adapter is instead connected to the controller s interface, it is prohibited to simultaneously use an RJ- plug; instead, the BACnet WiFi Adapter must then be powered by a wall adapter (standard -V USB wall adapter with micro USB connector). Wall Modules The TR0, TR0-CO, TR, TR-CO and PCD.Lx, Q.RCU-A-Txxx and T0x Wall Modules can be used in con-junction with the controller to perform room temperature sensing, setpoint adjustment, fan speed manual override, and occupancy override.

10 PCD.LRxx BACnet Room Controller PRODUCT DATA SHEET PP-00 EG0 I/O TERMIALS Relay Outputs CAUTIO Mixing of different voltages (e.g., V and 0 V) within the relay block is not allowed. The terminal blocks containing the controller s relay outputs are orange. Relay output types: See table OTE: If inductive components are to be connected to the relays and if these relays switch more often than once every two minutes, these components must be prevented from causing harmful interference to radio or television reception (conformance with E 0). Triac Outputs OTE: Recommended fuse (F):. A time-lag fuse (IEC). User must consider the correct voltage and max. breaking capacity / interrupting rate (line voltage urgently requires high breaking capacity / interrupting rate). The terminal blocks containing the controller s triac outputs are orange. These triac outputs can be configured (using, e.g., the ROOMUP configuration tool) for a variety of different functions, e.g., for connection to either a floating drive or to a thermal actuator. Once the triac outputs have been configured, the corresponding devices can then be connected to them directly. OTE: The VC actuator is intended for use at relay outputs, only and must not be used at the controller s triac outputs. Triac Current Limitations In the case of the 0-VAC versions of the controller, when the triacs are to be supplied with -VAC power from the controller s internal transformer, then the following applies: 00 ma max., i.e., a max. of one thermal actuator for heating and one thermal actuator for cooling can be operated (provided that heating and cooling are not operated at the same time). CAUTIO The max. permissible power output of all VAC terminals combined is 00 ma! If the triacs, alone, are loaded with 00 ma, then it is not permitted to connect a load at any other VAC output terminal. In all other cases, when the triacs are to be supplied with power ( VAC or 0 VAC) from an external source, then the following applies: 00 ma (peak) and 00 ma (max.), i.e., two to three thermal actuators can be operated in parallel (depending upon the current consumption of the given actuator). Universal Inputs The terminal blocks containing the controller s universal outputs are blue. Universal input types: See Table. The universal inputs are protected against voltages of max. VAC and 0 VDC (due to, e.g., miswiring). Bias Resistors Each universal input is equipped with one bias resistor. Analog Outputs The terminal blocks containing the controller s analog outputs are green. Analog output types: See Table. The analog outputs of the RLxx controllers (large housing) are protected against voltages of max. VAC and 0 VDC (due to, e.g., miswiring). OTE: Connecting VAC to any analog output of the RSxx controller (small housing) will damage the hardware.

11 PRODUCT DATA SHEET PP-00 EG0 PCD.LRxx BACnet Room Controller TROUBLESHOOTIG The controller features the following LEDs: T R T R! ACCESSORIES Terminal Protection Cover Required for wall mounting. Bulk pack, set of ten covers. For LARGE controllers, order no.: IRM-RLC For SMALL controller, order no.: IRM-RSC Fig.. Controller LEDs Table. Description of LED behaviors symbol color function, description T yellow ot used R yellow ot used T yellow LED indicating transmission of communication signals via the BACnet MS/ TP interface R yellow LED indicating reception of communication signals via the interface. yellow Status LED indicating firmware problems, hardware problems, etc. (see Table ) green red Power LED indicating firmware problems, hardware problems, etc. (see Table ) Watchdog (RLU, only) has locked controller (see Table ) APPROVALS, CERTIFICATIOS, AD STADARDS Approvals and Certifications UL 00-, Standard for Automatic Electric Controls for Household and Similar Use, Part : General Requirements; CA/CSA-E00-:0, Standard for Automatic Electrical Controls for Household and Similar Use, Part : General Requirements; Complementary listing for UL, CSA C. o. 0; BTL-listed, BACnet AAC profile; SASO-approved; CE-approved; FCC part B-compliant. Table. Status LED and power LED behaviors # Mode Power LED (green) Status LED (yellow) Power failure Stays OFF Stays OFF ormal operation O/OFF (0. Hz) Stays OFF o firmware O/OFF (0. Hz) O/OFF ( Hz) o valid MAC O/OFF (0. Hz) O/OFF (0. Hz) Auto-MAC O/OFF ( Hz) O/OFF (0. Hz) o application O/OFF (0. Hz) O/OFF (0. Hz) Short-circuiting O/OFF (0. Hz) Stays O Broken sensor O/OFF (0. Hz) Stays O Watchdog locked Turns O and stays Stays OFF

12 PCD.LRxx BACnet Room Controller PRODUCT DATA SHEET PP-00 EG0 Classification according to E 00- E 00 sub part E 00-- Environmental conditions For use in home (residential, commercial, and light-industrial) environments Construction Independently mounted electronic control unit with fixed wiring; panel-mounted on DI rail Action:type.C Rated impulse voltage V circuits 00 V Pollution degree Protection against shock Software classa 0 V circuits: 00 V Class 0 (without terminal cover) Class II (with terminal cover) Classification according to E 0 (Degree of protection provided by enclosures) IP0. In the case of controllers mounted outside of a cabinet, before applying power to the device, Terminal Protection Covers (-pc. bulk packs, order no.: IRM-RLC for large housings and IRM-RSC for small housings) must be mounted so as to provide IP0. Ambient Environmental Limits % r.h., non-condensing Operating temperature (floor/ceiling mounting): 0 0 C Operating temperature (wall/rail mounting): 0 0 C Storage temperature: 0 0 C Trademark Information BACnetTM is a trademark of ASHRAE Inc. PCD.LRL PCD.LRL + IRM-RLC PCD.LRS PCD.LRS + IRM-RSC PCD.LRS Fig.. PCD.LRxx without optional covers PCD.LRS + IRM-RSC Fig.. PCD.LRxx with optional covers (covers come in sets of ) Saia-Burgess Controls AG Bahnhofstrasse 0 Murten Switzerland T F info.ch@saia-pcd.com PP-00 EG0 0-0 U.S. Registered Trademark Copyright 0 Honeywell Inc. All Rights Reserved E0B-0GE-R0