LCD-DMD. Installation and Usage Instructions Stern SAM

Size: px

Start display at page:

Download "LCD-DMD. Installation and Usage Instructions Stern SAM"

Rodney Anderson
5 years ago
Views:

1 LCD-DMD Installation and Usage Instructions Stern SAM v0.1 May 2014 Copyright Dr Pinball

2 Important Please check Appendix A for details of machines that are compatible with LCD-DMD. It is important to note that LCD-DMD has not been tested on all of these machines it is the responsibility of the user to make a final decision about the suitability of this system for use on a particular pinball machine. The user installs LCD-DMD entirely at their own risk Dr Pinball cannot accept responsibility for damage or other problems caused by this system or its use. The installation instructions are given purely as a guide. The user must exercise caution when performing the installation.

3 Installation Step 1 - Preparation Switch off the pinball machine and remove the plug from the wall outlet. Remove the backbox translite glass. Remove the speaker panel and place onto the pinball machine use magnets or blutac on the side rails to stop the speaker panel from slipping. You may also need to open the backbox light door to gain access to the cabling inside. Step 2 - Remove the DMD display Figure 1 DMD screen, remove marked cables Figure 1 shows the DMD screen. Remove the ribbon cable and power connector from the screen. These cables are marked in the figure. Note that other variations of screen can be found in Stern machines in all cases remove both the power cable and the ribbon cable. The removed power cable is not needed by LCD-DMD and can be pushed safely out of the way.

Figure 2 remove the 8 bracket screws Also remove any earth cables that are fixed the screen.

4 Remove the 8 screws that hold the DMD screen onto the speaker panel. These screws hold the 2 mounting brackets. The screen and mounting brackets can then be removed from the machine. Figure 2 shows the screw locations only 4 screws are visible in the figure. Figure 2 remove the 8 bracket screws Also remove any earth cables that are fixed the screen.. Looking at the removed screen from the dots side, remove the 4 screws holding the DMD screen to the mounting brackets. The 2 mounting brackets should now be free from the screen the brackets will be used to mount LCD-DMD. This is shown in figures 3 and 4. Figure 3 - Remove the screws marked with red arrow to free bracket marked with blue arrow

Place the LCD-DMD onto the speaker panel and fix using the original DMD brackets and 4 of the original screws, as shown in figure 5 below.

5 Figure 4 - Remove the screws marked with red arrow to release bracket marked with blue arrow If the pinball machine has a transparent colored plastic film attached to the speaker panel, carefully remove it. Step 3 Install LCD-DMD Remove the protective film from the LCD-DMD screen. Place the LCD-DMD onto the speaker panel and fix using the original DMD brackets and 4 of the original screws, as shown in figure 5 below. Figure 5 Install the LCD-DMD Only 4 screws will be used to fix the brackets as the brackets must be attached using only the outside screw holes and the inside bracket holes.

6 Figure 6 Bracket moved out and fixed with only 2 screws Figure 6 above shows how the original bracket is mounted on the outside screw holes. The bracket pushes over the LCD-DMD mounting board and holds the new screen in position. Remember to reattach any earth cables when fixing the screen with the original brackets.

The position of J5 is shown in figure 7.

7 Step 4 Connect Data Cable If your game used a Pinled LED DMD a small circuit board is connected to connector J5 on the SAM CPU board. Take this circuit board out and install the ribbon cable directly in J5 on the SAM CPU Board. The position of J5 is shown in figure 7. Figure 7 Location of connector J5 (blue circle) on the SAM CPU board Connect the other end of the ribbon cable into the LCD-DMD socket this is shown in figure 8 below. Figure 8 Location of the ribbon cable

8 Step 5 Connect Power Cable The power cable plugs are keyed to ensure correct orientation. It is important the key is correctly located when connecting plug to socket. Failure to correctly connect the plug may result in damage to your pinball machine. Power for the LCD-DMD comes from the pinball CPU Board; the location of the board is shown in figure 9, highlighted in red. Figure 9 CPU Board location in red Locate the power connector and remove the existing plug and insert the end of the LCD-DMD power cable.

9 Figure 10 Power connector location in red Use the Power Cable Splice to reconnect the removed cable to the LCD-DMD power cable. Figure 11 shows the power cable including the power cable splice.

Figure 11 Power Cable and Splice Step 6 Check All Connections Before completing the installation please check all connections made for correct insertion and orientation.

10 Figure 11 Power Cable and Splice Step 6 Check All Connections Before completing the installation please check all connections made for correct insertion and orientation. Replace the speaker panel and backbox translite glass ensuring no cables are pinched. Step 7 - Configuration Use the DMD Extender Configuration Utility to configure the system for use with your screen. Please refer to the Configuration Utility manual for instructions on how to use. Start Up At start up you will be presented with a splash screen whilst the DMD Extender performs its initialisation. If a problem occurs during initialisation an error message will be displayed and the splash screen will remain in place. If a warning occurs the warning message will be displayed but the DMD Extender will continue to display the DMD output. Appendix B details all of the error and warning messages that could occur. Configuration To configure the DMD Extender you must use the DMD Extender Configuration Utility

11 DmdExtConfig.exe found on the SD Card. Please refer to the Configuration Utility manual for instructions on how to use. Appendix A This appendix gives details of machines that are compatible with the LCd-DMD. It is important to note that LCD-DMD has not been tested on all of these machines it is the responsibility of the user to make a final decision about the suitability of this system for use on a particular pinball machine. The user installs LCD-DMD entirely at their own risk Dr Pinball can accept no responsibility for damage or other problems caused by this system. If your machine is not listed below please contact us at info@drpinball.co.uk. Stern SAM system World Poker Tour Pirates of the Caribbean Family Guy Spider Man (Stern) Wheel of Fortune Shrek Indiana Jones 4 Batman (Stern) CSI: Crime Scene Investigation 24 NBA Big Buck Hunter Pro Iron Man Avatar The Rolling Stones (Stern) Tron Transformers AC/DC X-Men Avengers Metallica Star Trek

12 Appendix B Error Messages Error Message Comment CONFIG Config file not found The configuration file pinball.txt could not be found in the root directory of the SD Card CONFIG Invalid parameter name The name of a parameter is not a numeric value CONFIG Invalid parameter value The parameter value does not match the expected parameter content CONFIG Unknown parameter name The parameter name is not recognised as a valid parameter CONFIG Param 1002 greater than 384 pixels Screen height cannot exceed 384 pixels CONFIG Param 1001 too large DMD offset is too large the DMD would be displayed off the screen CONFIG Param 2001 too large Colour values range from to FFFFFF CONFIG Param 2002 too large Colour values range from to FFFFFF CONFIG Param 2003 too large Colour values range from to FFFFFF CONFIG Param 2004 too large Colour values range from to FFFFFF CONFIG Param 2005 too large Colour values range from to FFFFFF CONFIG Param 2006 DMD Type invalid DMD Type can be: 1 Bally / Williams 2 Data East / Sega 3 Sega Large 4 Stern SAM 5 Stern White Star CONFIG Param 2007 DMD Effect invalid DMD Effect can be: 1 Normal dots 2 Horizontal CRT effect 3 Vertical CRT effect 4 ZX Speccy CONFIG Param 1002 less than 96 pixels Screen height cannot be less than 96 pixels MMC CMD0 error occurred MMC CMD8 error occurred MMC CMD55 error occurred MMC CMD41 error occurred MMC CMD2 error occurred MMC0006 CMD3 error occurred MMC CMD7 error occurred MMC CMD17 error occurred SECURITY Invalid Key The product keys found in parameters 9001, 9002, 9003 and 9004 are invalid

13 If an error message occurs please contact quoting the full error message and any other values displayed.

DMD Extender. Installation and Usage Instructions Stern White Star

DMD Extender. Installation and Usage Instructions Stern White Star DMD Extender Installation and Usage Instructions Stern White Star V0.6 November 2013 Copyright 2013 - Dr Pinball Important Please check Appendix A for details of machines that are compatible with the DMD