PLC-R 21HC. PLC INTERFACE With SPDT Relay, High-Current Version. INTERFACE Data Sheet _03_en. Description

Transcription

1 PLC-R 2HC PLC INERFCE With SPD Relay, High-Current Version INERFCE Data Sheet 022_03_en PHOENIX CONC - 02/08 Description number of applications such as electrical heating systems require higher continuous load currents than miniature relays can carry and switch. Long Electrical Service Life he above-average service life of the contacts is particularly noticeable in the mid-load range when compared with less powerful relays. On average, the interval between servicing can be doubled or tripled, thus reducing costs. Rugged SPD Relay for Higher Loads he abbreviation "HC" in the designation stands for "High Current" applications with up to continuous current. he block contains a 6 power relay with PD contact application, so that additional reserves are used if overdimensioning occurs, e.g., in the event of temporary overload. he relay is secured against vibration by a captive retaining bracket and can be replaced if it becomes worn without having to remove the wiring. he relay is sealed with RII protection to protect the relay mechanics against external influences such as dust. Vibration-Resistant Plug-In ridge System Reduces the mount of Wiring Required nother feature of the PLC series is the FS 500 plug-in bridge system, which can be cut to any length. It can be plugged into the control and/or contact side "with a click" and snapped into place to ensure vibration-resistant connection. p to 35 PLCs can be clearly connected "to the block" within seconds, without any errors. dditional user-friendly wiring is provided by the contact connections arranged in pairs, if more than one conductor has to be connected per contact. dditional PLC dvantages Marking labels from the standard modular terminal block range Many other electromechanical relays and electronic solid-state relays are available in the PLC series Quick connection with protection against polarity reversal of eight PLCs to the control system via PLC-V8 adapter and system cable High-quality, vibration-resistant Phoenix Contact connection method Make sure you always use the latest documentation. It can be downloaded at conversion table is available on the Internet at his data sheet is valid for all products listed on the following page.

2 PLC-R 2HC Ordering Data Description ype Order No. Pcs./Pck. PLC INERFCE With Screw Connection PLC INERFCE with SPD relay, high-current version, comprising PLC-SC-... basic terminal block and plug-in miniature relay (see INERFCE catalog), for assembly on 3. PLC INERFCE With Spring-Cage Connection PLC INERFCE with SPD relay, high-current version, comprising PLC-SC-... basic terminal block and plug-in miniature relay (see INERFCE catalog), for assembly on 3. 2 V DC PLC-RSC- 2DC/2HC 24 V DC PLC-RSC- 24DC/2HC 24 V C/DC PLC-RSC- 24C/2HC 48 V DC PLC-RSC- 48DC/2HC 60 V DC PLC-RSC- 60DC/2HC V C/ V DC PLC-RSC-C/2HC 230 V C/2 V DC PLC-RSC-230C/2HC 2 V DC PLC-RSP- 2DC/2HC 24 V DC PLC-RSP- 24DC/2HC 24 V C/DC PLC-RSP- 24C/2HC 48 V DC PLC-RSP- 48DC/2HC 60 V DC PLC-RSP- 60DC/2HC V C/ V DC PLC-RSP-C/2HC 230 V C/2 V DC PLC-RSP-230C/2HC he PLC-P K insulating plate must be installed for voltages greater than 250 V (L, L2, L3) between the same terminal points on adjacent modules (see "ccessories"). FS 8-PLC... or FS is then used for potential bridging. ccessories Description ype Order No. Pcs./Pck. Insulating plate PLC-P K he PLC-P K insulating plate should be used in the following cases: always fit at the start and end of a PLC terminal strip for voltages greater than 250 V (L, L2, L3) between the same terminal points on adjacent modules (FS 8-PLC... or FS can be used for potential bridging) and for safe isolation between adjacent modules. For additional accessories such as power terminal blocks and plug-in bridges, please refer to the INERFCE catalog or echnical Data Input Data...2DC DC C DC DC......C C... Nominal input voltage N 2 V DC 24 V DC 24 V C/DC 48 V DC 60 V DC V C/ V DC Permissible range (with reference to N ) See "Operating Voltage Ranges" on page 4 ypical input current at N 33 m 8 m 7.5 m m m 4.5 m/ 4.2 m ypical response time at N 8 ms 7 ms ypical release time at N ms Input circuit DC C/DC Yellow LED, protection against polarity reversal, free-wheeling diode Yellow LED, bridge rectifier 230 V C/ 2 V DC 4.5 m/ 4.3 m he PLC-P K insulating plate must be installed for voltages greater than 250 V (L, L2, L3) between the same terminal points on adjacent modules (see "ccessories"). FS 8-PLC... or FS is then used for potential bridging. 022_03_en PHOENIX CONC 2

3 PLC-R 2HC Output Data Contact type Single contact, SPD Contact material gni Maximum switching voltage 250 V C/DC Minimum switching voltage 2 V C/DC Limiting continuous current (6 ) 2 Maximum inrush current 30 (300 ms) Minimum switching current 0 m Maximum shutdown power Ohmic load t = 0 ms 24 V DC 240 W (44 W) 2 48 V DC 58 W 60 V DC 48 W V DC 50 W 2 V DC 80 W 250 V C 2500 V (500 V) 2 Minimum switching power.2 W he PLC-P K insulating plate must be installed for voltages greater than 250 V (L, L2, L3) between the same terminal points on adjacent modules (see "ccessories"). FS 8-PLC... or FS is then used for potential bridging. 2 he values in brackets are for connections 2. If connections 2 are bridged, the values in brackets apply. General Data Impulse voltage withstand level mbient temperature range Operation Storage/transport -25 C C (230 V type -25 C C) -25 C C (230 V type -40 C C) Nominal operating mode 0% operating factor Inflammability class according to L 94 (housing) V0 Mechanical service life 3 x 7 cycles ir and creepage distances between the circuits IEC 60664, IEC 60664, DIN VDE 0, DIN EN 5078/VDE 06-60, IEC 60255/DIN VDE 0435 Pollution degree 3 Surge voltage category III Mounting position ny Mounting Can be aligned without spacing Conductor cross-section Screw connection, solid and stranded Spring-cage connection, solid and stranded 0.4 mm mm 2 (26-4 WG) 0.2 mm mm 2 (26-4 WG) Stripping length 8 mm Dimensions (W x H x D) 4 mm x 94 mm x 80 mm Housing material 6 kv Polybutylene terephthalate P non-reinforced, green he PLC-P K insulating plate must be installed for safe isolation between adjacent modules (see "ccessories"). FS 8-PLC... or FS is then used for potential bridging. ests/pprovals CE L GL c u F 022_03_en PHOENIX CONC 3

4 PLC-R 2HC lock Diagram N 2 ) 4 2 ) he input circuit depends on the type N= 24V DC / 24V C Figure lock diagram Operating Voltage Ranges N Figure 4 Operating voltage range for 24 V C/DC N= 2V DC N N= 48V DC Figure 2 Operating voltage range for 2 V DC N Figure 5 Operating voltage range for 48 V DC N= 24V DC Figure 3 Operating voltage range for 24 V DC 022_03_en PHOENIX CONC 4

5 PLC-R 2HC N N N= 2V DC N= 60V DC N= 230V C N= 2V DC N= 230V C Figure 6 Operating voltage range for 60 V DC Figure 8 Operating voltage range for 230 V C/DC N Figure 7 N= V C N= V DC N= V DC N= V DC Operating voltage range for V C/DC General Conditions Direct alignment in the block, all devices 0% operating factor, horizontal or vertical mounting. Curve Maximum permissible continuous voltage max with limiting continuous current on the contact side Curve Minimum permissible operate voltage op following pre-excitation 022_03_en PHOENIX CONC GmbH & Co. KG lomberg Germany 5 Phone: Fax: