fpl=^a^mqbo pi=^a^mqbo _~ëáå=^a^mqbo oéé~áê=fåëíêìåíáçåë

Size: px

Start display at page:

Download "fpl=^a^mqbo pi=^a^mqbo _~ëáå=^a^mqbo oéé~áê=fåëíêìåíáçåë"

Harold Williams
6 years ago
Views:

1 fpl=^a^mqbo pi=^a^mqbo _~ëáå=^a^mqbo oéé~áê=fåëíêìåíáçåë

2 A Contents ISO ADAPTER 1 Disassembly Assembling the handpiece holder Assembling the adapter, compl Function check Spare parts list...8 SL ADAPTER 1 Special tool Disassembly Assembling the handpiece holder Assembling the adapter, compl Function check Spare parts list Basic ADAPTER 1 Special tool Disassembly Assembling the handpiece holder Assembling the adapter, compl Function check Spare parts list ADAPTER D

3 fpl=^a^mqbo oéé~áê=fåëíêìåíáçåë ISO ADAPTER D

4 Disassembly 1 1 Unscrew screws 12 and carefully lift off handpiece holder Watch out for O-rings 9 and balls Press guide sleeve 1 out of motor sleeve 5. All remaining parts are now exposed. 1 5 ISO ADAPTER D

5 Assembling the handpiece holder 2 1 Spray O-rings 9 with T1 spray and insert them. 2 Also spray O-ring 18 with T1 spray and insert it in the groove provided with a blunt pair of tweezers. 3 Apply a light coat of Vaseline to balls 4 and insert them When fitting lock ring 10, note the position of the stop face. Just push the lock ring up to the stop. The position of the ring slot is unimportant here. 10 ISO ADAPTER D

6 Assembling the adapter, compl. 3 1 Insert fiber rod 2 in guide sleeve 1 and fasten with silicone D (E41). Correspondingly shaped profile bars are provided in the guide sleeve for the lugs of the optical fiber. (B) D B C 2 Complete guide sleeve 1 with spray tubes Align motor sleeve 5. Ring land C has two gaps of varying width. The narrower of these two gaps is assigned to the switching element. Slide the motor sleeve over the completed guide sleeve. 3 4 Insert spring ring Carefully attach the complete handpiece holder. Insert screws 12 with Loctite 932 and tighten them firmly. 1 ISO ADAPTER D

7 Function check 4 1 Couple the adapter to a Sirona SL motor and check the latching function. 2 To check the spray media ducts of the adapter, first connect the spray air duct of the supply hose to 2.0 bar. The flow rate must be between 1.8 and 4.5 Nl/min. Connect the spray water duct to an air pressure of 2.5 bar. The flow rate must be at least 5.0 Nl/min. The spray water flow rate at 2.0 bar must be at least 60 ml/min. 3 Leakage test: Use sleeve F to block the outlets of the spray media and apply a back pressure of 3 bar (air) to both of the spray media ducts. No pressure drop should occur. F ISO ADAPTER D

8 Spare parts list ISO adapter D ISO guide sleeve D Fiber rod ISO, compl D Spray tube D Ball, 2 mm Motor sleeve D O-ring 1.1 x 0.8 mm F Lock ring D Handpiece holder ISO D Screw M 1.6 x 5 DIN O-ring 8.4 x 0.7 mm D Spring ring E D O-ring 8 x 1 mm F0303 ISO ADAPTER D

9 pi=^a^mqbo oéé~áê=fåëíêìåíáçåë SL ADAPTER D

10 Special tool 1 A (31 W ) SL ADAPTER D

11 Disassembly 2 1 Attach adapter to tool A Unscrew screws 12 and carefully lift off handpiece holder 11. Watch out for O-rings 9 and balls A (31 W ) 3 Press guide sleeve 1 out of motor sleeve 5. All remaining parts are thus exposed. 1 5 SL ADAPTER D

12 Assembling the handpiece holder 3 1 Spray O-rings 9 with T1 spray and insert them. 2 Also spray O-ring 18 with T1 spray and insert it in the groove provided with a blunt pair of tweezers. 3 Apply a light coat of Vaseline to balls 4 and insert them When fitting lock ring 10, note the position of the stop face. Just push the lock ring up to the stop. The position of the ring slot is unimportant here. 10 SL ADAPTER D

13 Assembling the adapter, compl. 4 1 Clamp optical fiber 2 onto guide sleeve 1. Correspondingly shaped profile bars are provided in the guide sleeve for the lugs (B) and the groove (C) of the optical fiber. C 2 B D 2 Attach guide sleeve 1 to tool A and complete with spray tubes 3, compression spring 6 and switching element Align motor sleeve 5. Ring land D has two gaps of varying width. The narrower of these two gaps is assigned to the switching element. Slide the motor sleeve over the completed guide sleeve. 4 Insert spring ring Carefully attach the complete handpiece holder. Insert screws 12 with Loctite 932 and tighten them firmly A (31 W ) SL ADAPTER D

14 Function check 5 1 Couple the adapter to a Sirona SL motor and check the latching function. 2 To check the spray media ducts of the adapter, first connect the spray air duct of the supply hose to 2.0 bar. The flow rate must be between 1.8 and 4.5 Nl/min. Connect the spray water duct to an air pressure of 2.5 bar. The flow rate must be at least 5.0 Nl/min. The spray water flow rate at 2.0 bar must be at least 60 ml/min. 3 Leakage test: Use sleeve F to block the outlets of the spray media and apply a back pressure of 3 bar (air) to both of the spray media ducts. No pressure drop should occur. F SL ADAPTER D

15 Spare parts list Adapter SL Guide sleeve D Optical fiber, compl D Spray tube D Ball, 2 mm Motor sleeve D Compression spring D Switching element, short D O-ring 1.1 x 0.8 mm F Lock ring D Handpiece holder, compl D Screw M 1.6 x 5 DIN O-ring 8.4 x 0.7 mm D Spring ring E D O-ring 8 x 1 mm F Circlip D3185 SL ADAPTER D

16 _~ëáå=^a^mqbo oéé~áê=fåëíêìåíáçåë Basic ADAPTER D

17 Special tool 1 A (31 W ) Basic ADAPTER D

18 Disassembly 2 1 Attach adapter to tool A Unscrew screws 12 and carefully lift off handpiece holder 11. Watch out for balls A (31 W ) 3 Press guide sleeve 1 out of motor sleeve 5. All remaining parts are thus exposed. 1 5 Basic ADAPTER D

19 Assembling the handpiece holder 3 1 Spray O-ring 18 with T1 spray and insert it in the groove provided with a blunt pair of tweezers. 2 Apply a light coat of Vaseline to balls 4 and insert them When fitting lock ring 10, note the position of the stop face. Just push the lock ring up to the stop. The position of the ring slot is unimportant here. 10 Basic ADAPTER D

20 Assembling the adapter, compl Attach guide sleeve 1 to tool A. 2 Align motor sleeve 5. Slide motor sleeve over guide sleeve 1. 3 Insert spring ring Carefully attach the complete handpiece holder. Insert screws 12 with Loctite 932 and tighten them firmly A (31 W ) Basic ADAPTER D

21 Function check 5 1 Couple the adapter to a Sirona SL motor and check the latching function. 2 To check the spray media ducts of the adapter, first connect the spray air duct of the supply hose to 2.0 bar. The flow rate must be between 1.8 and 4.5 Nl/min. Connect the spray water duct to an air pressure of 2.5 bar. The flow rate must be at least 5.0 Nl/min. The spray water flow rate at 2.0 bar must be at least 60 ml/min. 3 Leakage test: Use sleeve F to block the outlets of the spray media and apply a back pressure of 3 bar (air) to both of the spray media ducts. No pressure drop should occur. F Basic ADAPTER D

22 1 Spare parts list Adapter, Basic D Guide sleeve, Basic D Ball, 2 mm Motor sleeve D Lock ring D Handpiece holder Basic D Screw M 1.6 x 5 DIN O-ring 8.4 x 0.7 mm D Spring ring E D O-ring 8.0 x 1.0 mm F Circlip D Basic ADAPTER D

23 té=êéëéêîé=íüé=êáöüí=íç=ã~âé=~åó=~äíéê~íáçåë=ïüáåü=ã~ó=äé=êéèìáêéç=çìé=íç=íéåüåáå~ä=áãéêçîéãéåíëk «=páêçå~=aéåí~ä=póëíéãë=dãäe=ommr péê~åüéw=éåöäáëåü= mêáåíéç=áå=déêã~åó a=pnurkmtskmokmqkmo===nmkommr ûkjkêkw NMR=OOO fãéêáã =Éå=^ääÉã~ÖåÉ páêçå~=aéåí~ä=póëíéãë=dãäe få=íüé=rp^w c~äêáâëíê~ëëé=pn páêçå~=aéåí~ä=póëíéãë=ii` SQSOR=_ÉåëÜÉáã QUPR=páêçå~=aêáîÉI=pìáíÉ=NMM déêã~åó `Ü~êäçííÉI=k`=OUOTP ïïïkëáêçå~kåçã rp^ få=`~å~ç~w páêçå~=`~å~ç~ PORM=oáÇÖÉï~ó=aêáîÉ=J=råáí=R jáëëáëë~ìö~i=låí~êáç=iri=rvs `~å~ç~ lêçéê=kçk RU=TV=TUP=a=PNUR

MVKOMNM. kéï=~ë=çñw== `bob`=l=áåi~ä=j`=ui. lééê~íáåö=íüé=j`=ui=îá~=i^k. båöäáëü

MVKOMNM. kéï=~ë=çñw== `bob`=l=áåi~ä=j`=ui. lééê~íáåö=íüé=j`=ui=îá~=i^k. båöäáëü kéï=~ë=çñw== MVKOMNM `bob`=l=áåi~ä=j`=ui lééê~íáåö=íüé=j`=ui=îá~=i^k båöäáëü Contents Sirona Dental Systems GmbH Contents 1 Preparations... 3 2 Windows 7... 4 2.1 Deactivating the WLAN card... 4 2.2 Configuring