HXV SERIES HIGH VOLTAGE SWITCHING SYSTEMS

Transcription

1 BULLETIN HXV (v) HXV SERIES HIGH VOLTAGE SWITHING SYSTEMS The HXV Series are computer controlled switching systems designed for High Voltage applications. Standard systems handle signals up to volts, while custom systems switching up to kv are possible. Typically applications include Hi-pot and high voltage IR testing. HXV/ Mainframe with keypad manual control FEATURES: Standard relays hot switch up to volts or amps, carry volts and amps. ustomized systems switch up to kv. Front panel LEDs show switch status and aid in debugging. omputer ontrol via Ethernet LAN, combined IEEE/RS Serial or TTL. Remote Status feedback to controlling computer. Manual ontrol option for use without computer control. HASSIS: The HXV Units are 9" rack mounted chassis, and are available as either mainframes or expansion chassis that are pre-wired to accept any of the HXV Series high voltage switch modules. All chassis have front panel LEDs showing open and closed switch points. Signal I/O connectors protrude through the rear panel. HXV/ Mainframe or -E Expansion hassis -- relay drives allow four HXV/x or HXV/x modules to be installed, or two HXV/K modules. The chassis height is.". HXV/9 Mainframe or -E Expansion hassis -- furnishes 9 relay drivers, controlling up to HXV/x or HXV/x modules, or six HXV/K Switch Modules in a " high chassis. HXV/ Mainframe or -E Expansion hassis -- Up to relay drives. ontrols up to HXV/x or HXV/x modules, or eight HXV/K modules in a." high chassis. Expansion hassis - Up to expansion chassis are run from a single Mesa ontroller, allowing systems with up to 9 switch points to be built. HXV chassis can be mixed with other ytec products to provide a complete turn-key switching solution. SWITH MODULES: HXV/x Modules -- Individual modules can be wired together to build larger xn multiplexer configurations. Interconnects are located either externally or inside the chassis using screw terminal connectors built into the switch modules. HXV/x Modules -- Are used to build xn matrices. Useful for HiPot testing and Insulation Resistance testing where Hi and Low must be switched between any two of many measuring points. HXV/K Modules --- Furnish SPST discrete relays which can be externally interconnected to form various configurations. HXV-

2 I I HXV HASSIS The HXV hassis are 9" rack mounting units with built-in power supplies that are pre-wired to hold the HXV Series switch modules. Switch modules are mounted so that their I/O connectors protrude through the rear panel. Every chassis front panel has discrete LEDs showing the status of all switch points and also holds the optional manual control. HXV/ MAINFRAME OR -E EXPANSION HASSIS This chassis controls switch points. A number of different switching configurations are possible. Add the required switch module(s) and a control module to complete the system. Dimensions: Weight: A Power : 9" rack mount ( mm) " deep ( mm)." ( RU) high (9 mm) lbs (9 Kg) max watts max. / selectable. O HXV/ with pushbutton manual control option SWITH SELET (HXV/x) RS- IEEE- RS- LINK A/ IN UTP / / / / SWITH SELET (HXV/x) HXV/ MAINFRAME This chassis controls switch points in a variety of different possible configurations. L Display/Driver Modules drive the associated switch modules and have built-in LEDs showing switch status. The LEDs are visible thru the front panel. Add switch modules, Ls, a control module and the optional manual control to complete the system. Standard chassis measure." deep and." high. Purchasing a larger than required mainframe, only partially filled, allows for cost-effective future expansion. Dimensions: 9" rack mount ( mm) Weight: lbs ( Kg) max " deep ( mm) A Power : watts max. / selectable." ( U) high (mm) TYPIAL x MODULE TYPIAL K- MODULE TYPIAL x MODULE 9 (HXV/x) / (HXV/x) / / / RS- RS- K-Module Addressing O LINK IEEE- UTP A/-IN ALL HASSIS Material: Mounting Hardware: Protection: Gray Anodized extruded or sheet aluminum with a polycarbonate front panel overlay. Rack Mount handles are standard. Flush mount flanges available at no added cost. Selectable A input fused at: amps VA, amp VA. FOR TEHNIAL ASSISTANE, PLEASE ONTAT YTE AT -- OR VISIT OUR WEBSITE AT cytec-ate.com HXV-

3 HXV/9 MAINFRAME This chassis controls up to 9 switch points. A typical application would be HXV/x Switch Modules, but many configurations are possible using different switch modules. One L Display/Driver Modules is needed to drive each switch modules. The Ls also have built-in LEDs that show switch status. Add switch modules, the required Ls, a control module and the optional keypad manual control to complete the system. Standard chassis measure." deep and " high. Purchasing a HXV/9 chassis only partially filled with switch modules allows cost-effective future expansion. Dimensions: 9" rack mount ( mm) Weight: lbs ( Kg) max " deep ( mm) A Power : watts max. / selectable " (U) high ( mm) HXV/9 Mainframe with with IEEE/RS, Ethernet and manual M- Keypad ontrols HXV EXPANSION HASSIS HXV/, /9 and / are also built as expansion chassis that are used with a MESA ontrol hassis as shown in the MESA Bulletin. Multiple expansion chassis allow large or complex systems having one point of control to be configured, resulting in cost savings. Expansion chassis do not have control modules installed. Add switch modules and L Display/Driver Modules for the HXV/ and HXV/9 as needed to complete the system. ONNETORS Three standard connectors are offered: ) Binding Post / Banana Jack -- Simple, multiple connection methods using stripped wire or Banana plugs. ) Shrouded Banana Jacks -- Easy, inexpensive connections with higher level of safety than standard BP connectors. ) oaxial SHV -- used for applications requiring shielded external wiring for safety codes. SHVs are similar to BNs but can NOT be plugged into BNs. More expensive and more difficult to wire but required in some installations for safety reasons. Binding Post (Banana Jack) Shrouded Banana Jack Shrouded Banana Jack LED INDIATORS / STATUS FEEDBAK All HXV Mainframe and Expansion hassis have LED displays that show the on/off state of every relay. The LED indicators are visible on the front panel and are labeled to match the programmatic address of the relays. The LEDs provide an invaluable aid for program debugging and troubleshooting. They allow the user to easily verify switch point status by simply looking at the system's front panel. HXV/ chassis have switch status LEDs built into the front panel. The LEDs are included in the chassis price. HXV/ 9 and / Mainframes chassis require one L Display Module to drive each switch module. L LEDs are visible thru cutouts in the front panel. These display modules must be purchased separately, in addition to the switch modules. HXV USTOM SYSTEMS YTE orp. takes pride in building custom systems that meet non-standard or special customer specifications. Please call --- or sales@cytec-ate.com to contact an Application Engineer and discuss details. HXV/x-BP Switch Module FOR TEHNIAL ASSISTANE, PLEASE ONTAT YTE AT -- OR VISIT OUR WEBSITE AT cytec-ate.com HXV-

4 HXV SERIES SWITH MODULES The HXV Series switch modules are built with special high voltage reed relays that hot switch up to volts and cold switch carry volts. Applications include HiPot testing, insulation breakdown testing and other extreme voltage requirements. Standard I/O signal connectors are either -BP (Binding Posts), -SBJ (Shrouded Banana Jack) or -SHV coaxial. The modules can be wired together internally to furnish larger configurations while eliminating external connections. For example, chassis can be supplied prewired as x to x multiplexers, or as x to x matrices. HXV/x This switch module has eight Form A (Normally Open) relays arranged in an x configuration as shown in Fig.. A screw terminal connector is built into the module so that the OM connections of several modules may be wired together inside the chassis to form larger multiplexers. HXV/x This switch module is built with eight Form A (SPST) relays arranged in a x matrix configuration as shown in Fig.. Built-in screw terminal connectors allow the two OM connections to be wired together with other switch modules inside the chassis to form larger matrices such as x, x, etc. OM Fig. HXV/x Switch Module HXV/-K This module is built with eight individual Form A Normally Openrelays. Each relay is wired out to one input and one output connector. See Fig.. The module takes up a double slot in the chassis. Fig. HXV/x Switch Module RELAY SPEIFIATIONS ontact Rating Switch Voltage Switch urrent arry urrent Breakdown Voltage Operating Time Life Expectancy Power consumption RF Specs: Bandpass Isolation SOFTWARE WARRANTY Watts Volts. Amps. Amps Volts RMS. msec million operations mechanical VD =. Watts D to MHz (individual modules) Free drivers and/or sample programs are available for the most commonly available application programming languages. YTE orp. warrants that all products are free from defects in material or workmanship for a period of five years. USTOM SYSTEMS ARE AVAILABLE. DON'T SEE WHAT YOU NEED? PLEASE ALL FOR MORE OPTIONS. ONTROL MODULES Fig. HXV/K Switch Module IF- LAN / GPIB / RS ontrol ytec s newest control module has the three most popular control interface protocols built into one module and is backwards compatible with all previous ytec control modules. LAN - /BaseT Ethernet with an RJ onnector. GPIB - IEEE. compliant control module. RS - Standard D9 serial port which can be used from computer com ports or USB to OM port cables USB - A USB to RS onvertor is provided to allow simple control through USB Ports. MANUAL ONTROL OPTION Manual ontrols are available for all mainframe chassis. HXV/ Mainframes chassis can be purchased with an optional channel pushbutton manual control PB/. HXV/9 and HXV/ mainframes can be built with optional keypad manual controls M-. FOR TEHNIAL ASSISTANE, PLEASE ONTAT YTE AT -- OR VISIT OUR WEBSITE AT cytec-ate.com HXV-

5 Programmable switching systems for automated test, data acquisition and communications KV HIGH VOLTAGE X MULTIPLEXER ytec Model HXV/x-KV FEATURES:, V Form relays. 9" rack mount x " deep x." tall ( RU ). x, Normally Open or Normally losed configuration. Single wire common, multiwire x connectors. / Ethernet LAN, GPIB and RS remote control. Full LED display & remote status feedback. Manual ontrol for use without computer control. Simple command set and addressing. Programming examples available in all popular languages. Five Year Warranty! Field proven for years. HXV/x-KV Front Panel Other Features: Safety Interlock relay automatically disables relays. ommon disconnect relay allows common grounding or charge dumps. Relays may be wired as Form A, Form B or Form. High reliability Gigavac Relays. Ground lugs next to all connectors. Front panel manual control lockout from remote. Opto Isolated drives. See schematic on page of bulletin. x with LAN and RS Rear Panel SWITH SPEIFIATIONS Max Switched Voltage, V Peak Max arry urrent A continuous Operating Time ms Life Expectancy Million cycles cold switched, cycles at max power Dimensions 9" rack mount Width, " Depth,." Height Weight lbs Model HXV/x-KV $,. omplete days ARO. Smaller and larger systems are available. Many other relay and connector types available. ustom systems with little to no NRE. all or for quotes or technical help. LabView, LabWindows and IVI drivers available.* LabView and LabWindows are trademarks of National Instruments. View more of ytec's HXV Series offerings. ontact ytec at --- or sales@cytec-ate.com

6 D B A.... G F E ytec x High Voltage Mux with harge Dump relay on the common. KV Relays Gigavac P/N G-W-F N Position to Output connectors onnector TE 9- for gage wire, position. ommon J ommon connector GES HB PTFE Panel Mount Receptacle P/N 9 J J J 9 DEEP ETH & LEAR ANODIZE TOL. +/-." U.O.S. DATE: --9.ai AD FILE: DRAWN BY: NNT SIZE: TITLE: OMMENTS: System Schematic DRAWING NUMBER: --9 Rev A G F E D B A