CATALOGUE G03-MINI-ITX-AD-F V4.0

Transcription

1 CATALOGUE G03-MINI-ITX-AD-F V4.0. AD2COM-PB. 2. AD4COMB-PB AD4COM-PB ADRTLANP-LF / ADRTLANG-LF AD3RTLANP-LF / AD3RTLANG-LF ADPCM2-PB / ADPCM-PB ADCF AD2VC-PB. 9. AD7DLV-LF 2 0. AD7LVCOM-PB..6. ADPE4S-PB AD9CRT2LAN-PB AD9CRT4C2L-PB AD9LV4COM-PB AD9HDMI-PB AD8DVI-PB AD3INLANG-PB AD8TV-PB ADMPCIA-PB AD2VD-PB.4

2 AD2COM-PB Mini-ITX Two serial ports Adapter Dimension: 75 x 82 mm Chipset: FINTEK F7805F Features: Two high-speed 6C550 compatible UART with 6-byte FIFOs Fully programmable serial-interface characteristics Baud rate up to 5.2K Connectors: 2 serial ports (COM3 & COM4)

3 AD4COMB-PB Four serial ports Adapter Features: Four high-speed 6C550 compatible UART with 6-byte FIFOs Fully programmable serial-interface characteristics Baud rate up to 5.2K Support RS422/485 function Connectors: 4 serial ports (COM3, COM4, COM5 &COM6) Cable: Two COM port Connector Cable for connect COM_5 & COM_6 Headers and COM port Connectors 2

4 Part I.PIN DEFINITION. COM3&COM4 2.COM5&COM6 Pin P Pin6 Pin Pin6 COM5 COM6 Pin Definition for COM3&COM4&COM5&COM6 Pin No. Pin Definition Pin No. Pin Definition DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RI 5 GND 3

5 3. JP5&JP2 Pin Pin2 Pin Pin2 JP5 JP2 Pin Definition for JP5&JP2 when RS422 Selected Pin No. Pin Definition Pin No. Pin Definition TXDP 2 TXDN 3 RXDP 4 RXDN Pin Definition for JP5&JP2 when RS485 Selected Pin No. Pin Definition Pin No. Pin Definition DATAP 2 DATAN 4

6 Part II Jumper setting to select RS 232/ RS 485/ RS 422 Function JP6&JP4 is used to select RS 232/RS 485/ RS 422 Function for COM5&JP5 JP3&JP is used to select RS 232/RS 485/ RS 422 Function for COM6&JP2-2:RS :RS :RS422 JP6/JP3 Pin JP6 Pin JP3 JP4 JP -2:RS :+2V 5-6:+5V JP/JP4 I.Pin&Pin2 in both JP6& JP4 closed to select RS232 for COM5, Or Pin&Pin2 in both JP3&JP closed to select RS232 for COM6. II.Pin3&Pin4 in JP6/JP3 closed to select RS485 Function for JP5 or JP2, Pin3&Pin4 in JP4 /JPclosed to Enabled +2V for JP5 or JP2 III.Pin5&Pin6 in JP6/JP3 closed to select RS422 Function for JP5 or JP2, Pin5&Pin6 in JP4/JP closed to Enabled +5V for JP5 or JP2 Flow Control: RS485 Control by RTS signal. Programmer should set RTS signal high before sending data. 5

7 AD4COM-PB Mini-ITX Four serial ports Adapter Dimension: 92 x 82 mm Chipset: FINTEK F826DG Features: Four high-speed 6C550 compatible UART with 6-byte FIFOs Fully programmable serial-interface characteristics Baud rate up to 5.2K Connectors: 4 serial ports (COM3, COM4, COM5 &COM6) Cable: Two COM port Connector Cable for connect COM_5 & COM_6 Headers and COM port Connectors 6

8 ADRTLANP-LF / ADRTLANG-LF Mini-ITX LAN port Adapter Dimension: 75 x 82 mm Chipset: RealTek RTL80S Giga-LAN for ADRTLAN-G RealTek RTL800C 0/00-LAN for ADRTLAN-P Features: Integrated 0/00 transceiver for ADRTLAN-P Integrated 0/00/000 transceiver for ADRTLAN-G Supports PVI rev:2.3, 32bit, 33/66MHz Supports Full Duplex flow control (IEEE 802.3x) Fully compliant with IEEE 802.3, IEEEE802.3u, IEEE802.3ab Connectors: one RJ45 LAN connector 7

9 AD3RTLANP-LF / AD3RTLANG-LF Mini-ITX three LAN ports Adapter Dimension: 75 x 82 mm Chipset: RealTek RTL80S Giga-LAN for AD3RTLAN-G RealTek RTL800C 0/00-LAN for AD3RTLAN-P Features: Integrated 0/00 transceiver for AD3RTLAN-P Integrated 0/00/000 transceiver for AD3RTLAN-G Supports PVI rev:2.3, 32bit, 33/66MHz Supports Full Duplex flow control (IEEE 802.3x) Fully compliant with IEEE 802.3, IEEEE802.3u, IEEE802.3ab Connectors: three RJ45 LAN connectors ATTENTION: Only suitable driver installed, these models (ADRTLANG, ADRTLANP, AD3RTLANP, and ADPE4S) can work properly. 8

10 ADPCM2-PB / ADPCM-PB Mini-ITX PCMCIA/ CF Adapter ADPCM ADPCM2 Dimension: 90 x 82 mm Chipset: RICOH R5C486 PCI-CARDBUS BRIDGE Features: - Support one 6-bit (PCMCIA2./ JEIDA4.2) card socket and one CF(Compact Flash) socket - PC 200 Design Guide Compliant - Compliant with PC card Standard Release 8.0 Specification - 5 programmable memory windows and 2 programmable I/O windows - Compliant with i82365sl compatible register set/ ExCA - Power decreased by the improvement of Power Management - Compliant with PVI Local Bus Specification Plug and Play support 9

11 ADCF Mini-ITX Compact Flash Adapter Dimension: 75 x 82 mm - Replacement for 3.5" hard disk drives - Bootable device - Behaves like an IDE disk, no special drivers required - Plugs directly onto a 40 pin IDE connector - Uses a floppy power connector - Jumper configuration: master - Not recommended for high vibration environments - Jumper Setting: JP 2-3 closed: CF power by 5V 4-5 closed: CF power by 3.3V -2 closed reserve (no function) 0

12 AD2VC-PB 2V Mini-ITX Power supply Dimension: 60 x 45 mm -00 Watt DC-DC power supply - ATX standard compliant - 2V operation - 00% silent, small footprint - Plugs directly into the motherboard ATX connector

13 AD7DLV-LF Mini-ITX 24-bit LVDS Panel Interface &DVI Port Adapt (For J7F2W Series) Dimension: 92 x 82 mm Function: - LVDS Panel Controller and DVI Connector - VIA VT636 Chip Supporting LVDS Signal for LVDS Panel -VIA VT632A Supporting DVI digital signal Output 2

14 . Inverter: LVDS Inverter headers Pin and pin2: VCC of inverter Pin3 pin4 and pin6: GND Pin5: Backlight Pin7: Brightness Pin VCC VCC GND GND Backlight GND Brightness 2. LCD (32 Pin): 24-bit LVDS header Pin 2 Pin 24-bit LVDS Header 3

15 32 Pin Definition Pin No. Pin Definition Pin No. Pin Definition TXE3-2 TXE3+ 3 TXEC- 4 TXEC+ 5 TXE2-6 TXE2+ 7 TXE- 8 TXE+ 9 TXE0-0 TXE0+ GND 2 GND 3 GND 4 GND 5 GND 6 GND 7 TXO3+ 8 TXO3-9 TXOC+ 20 TXOC- 2 TXO2+ 22 TXO2-23 TXO+ 24 TXO- 25 TXO0+ 26 TXO0-27 Pannel_VCC 28 Pannel_VCC 29 Pannel_VCC 30 Pannel_VCC 3 GND 32 GND 4. JP: LVDS 5V/3.3V Function setting (3-pin) JP 3 JP 3-2 closed: PVDD= 5V 2-3 closed : PVDD= 3.3V 4

16 5. JP2: Panel backlight power on/off (3-pin) JP2 3 JP2 2-2 closed: backlight off 2-3 closed : backlight on 5

17 AD7LVCOM-PB Mini-ITX 24-bit LVDS Panel Interface & COM Ports Adapt (For J7F2W Series) Dimension: 92 x 82 mm Function: - 24-bit LVDS Panel Controller and Serial Port - VIA VT636 Chip Supporting LVDS Signal for LVDS Panel Chipset: FINTEK F7805F Features: Two high-speed 6C550 compatible UART with 6-byte FIFOs Fully programmable serial-interface characteristics Baud rate up to 5.2K Connectors: 2 serial ports (COM3 & COM4) 6

18 . Inverter: Inverter Control Signal connector Pin#&Pin#2: +2V Pin#3, Pin#4 &Pin#6: GND Pni#5: LCD Back Light ON/OFF Control Pin#7: LCD Panel Brightness Control Pin +2V +2V GND GND Backlight GND Pin 7 Brights Inverter Connector 2. JP: LVDS 5V/3.3V Function setting (3-pin) -2 closed: +5V Panel Signal Voltage 2-3 closed: +3.3V Panel Signal Voltage JP 3 JP 3-2 closed: PVDD= 5V 2-3 closed : PVDD= 3.3V 7

19 3. JP2 (only for PCB ver: 0.2): Panel backlight power on/off (3-pin) -2 closed: OFF 2-3 closed: ON JP2 3 JP2 2-2 closed: backlight off 2-3 closed : backlight on Note: JP2 only for PCB rev: 0.2 please check the character which below the COM4 connector it has V:0.2, if it is V:0. did not have JP2 connector 4. LCD (32 Pin): 24-bit LVDS header 2, 4, 6, 8, Pin, 3, 5, 7, bit LVDS Header 8

20 . 32 Pin Definition Pin No. Pin Definition Pin No. Pin Definition TXE3-2 TXE3+ 3 TXEC- 4 TXEC+ 5 TXE2-6 TXE2+ 7 TXE- 8 TXE+ 9 TXE0-0 TXE0+ GND 2 GND 3 GND 4 GND 5 GND 6 GND 7 TXO3+ 8 TXO3-9 TXOC+ 20 TXOC- 2 TXO2+ 22 TXO2-23 TXO+ 24 TXO- 25 TXO0+ 26 TXO0-27 Pannel_VCC 28 Pannel_VCC 29 Pannel_VCC 30 Pannel_VCC 3 GND 32 GND 9

21 ADPE4S-PB Raid Setting: A. Motherboard: The IPC board with the 20-pin connector. B. Daughter card: ADPE4S, SATA connector, support Raid. Process:. Make the Raid Driver Floppy Disk. The floppy disk, CD, USB flash disk is ok when the operating system is Vista. 20

22 2.Boot-strap, when the following picture appears. 3. Press Ctrl+M key in to BIOS Setup interface. 2

23 4. Setting Raid mode, as follows. 5. Quit after save it when the Windows installation interface appears, as follows 22

24 6. Press F6 before Press F6 if you need to install a third party SCSI or RAID driver appears, then following interface will appear. It is no need pressing F6, just install driver in the Finding HDD interface when the operating system is Vista. 7. Press the key of S, input the floppy disk. 8. Choose the Marvell 6xx SATA Controller 32bit Drive or Marvell 6xx SATA Controller 64bit Driver according the uses driver floppy disk program. 23

25 AD9CRT2L-PB Feature: Support Intel secondly VGA port. Support Two RealTek Giga-LAN port. Ports: Two RJ45 LAN and one VGA port. 24

26 AD9CRT4C2L-PB Feature: Support Intel secondly VGA port. Support Two RealTek Giga-LAN port. Support Three RS-232 serial ports. Support One RS-232/422/485 serial ports. Port: Two RJ45 LAN and one VGA Port. Connectors: 4 serial ports (COM, COM2, COM3 &COM4(TX-RXCOM4)) 25

27 Part I.PIN DEFINITION.COM, COM2, COM3, COM4 COM2 COM COM3 COM4 Pin6 P Pin6 Pin6 Pin Pin6 Pin Pin Pin COM COM2 COM3 26 COM4 Pin Definition for COM&COM2&COM3&COM4 Pin No. Pin Definition Pin No. Pin Definition DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RI 5 GND

28 2. TX-RXCOM4: RS-422 or RS485 TX-RXCOM4 TXDN RXDN TX-RXCOM4 Pin 2 TXDP RXDP RS422/485 Header 3. JCOMP4: RS232 Power Function Select JCOMP4-2 closed: RS closed : +2V 5-6 closed : +5V 27

29 4. JCOM4: RS232, RS485, RS422 Function select JCOM4-2 closed: RS closed : RS closed : RS JCOMP3: RS232 Power Function Select JCOMP3-2 closed: RS closed : +2V 5-6 closed : +5V 28

30 AD9LV4COM-PB Feature: Support Intel secondly LVDS port. Support Three RS-232 serial ports. Support One RS-232/422/485 serial ports. 29

31 . LVDS Headers: LVDS LVDS LVDS Header Pin Pin 2 Pin Number Pin Define Pin Number Pin Define Pin LVDSB_DATA3- Pin 2 LVDSB_DATA3+ Pin 3 LVDSB_CLK- Pin 4 LVDSB_CLK+ Pin 5 LVDSB_DATA2- Pin 6 LVDSB_DATA2+ Pin 7 LVDSB_DATA- Pin 8 LVDSB_DATA+ Pin 9 LVDSB_DATA0- Pin 0 LVDSB_DATA0+ Pin DDC DATA Pin 2 DDC CLOCK Pin 3 Ground Pin 4 Ground Pin 5 Ground Pin 6 Ground Pin 7 LVDSA_DATA3+ Pin 8 LVDSA_DATA3-30

32 Pin 9 LVDSA_CLK+ Pin 20 LVDSA_CLK- Pin 2 LVDSA_DATA2+ Pin 22 LVDSA_DATA2- Pin 23 LVDSA_DATA+ Pin 24 LVDSA_DATA- Pin 25 LVDSA_DATA0+ Pin 26 LVDSA_DATA0- Pin 27 PVDD Pin 28 PVDD Pin 29 PVDD Pin 30 PVDD Pin 3 Ground Pin 32 Ground 2. Pin definition for COM, COM2, COM3, COM4 COM&COM2 3

33 Pin6 P Pin Pin6 Pin COM4 COM3 Pin No. Pin Definition Pin No. Pin Definition DCD 6 DSR 2 RXD 7 RTS 3 TXD 8 CTS 4 DTR 9 RI 5 GND 2. JP: LVDS 5V/3.3V Function setting (3-pin) -2 closed: Panel PVDD +5V Voltage 2-3 closed: Panel PVDD +3.3V Voltage JP JP closed: PVDD= 5V 2-3 closed : PVDD= 3.3V 32

34 2. JP2: Inverter VCC 2V/5V Function setting (3-pin) JP2 JP closed: INVERTER 2V 2-3 closed : INVERTER 5V 3. JCOMP3: RS232 Power Function Select JCOMP3-2 closed: RS closed : +2V 5-6 closed : +5V 33

35 4. JCOMP4: RS232 Power Function Select JCOMP4-2 closed: RS closed : +2V 5-6 closed : +5V 5. JCOM4: RS232, RS485, RS422 Function select JCOM4-2 closed: RS closed : closed :

36 6. TX-RXCOM4: RS422/485 Header TXDN RXDN TX-RXCOM4 Pin 2 TXDP RXDP RX-TXCOM4 RS422/485 Header 7. Inverter: Pin-headers of LVDS Inverter Pin and pin2: VCC of inverter Pin3 pin4 and pin6: GND Pin5: Backlight Pin7: Brightness Pin VCC VCC GND GND Backlight GND Brightnes 35

37 AD9DHDMI-PB Feature: Support Intel DVI or HDMI port. Port: One DVI Port One HDMI Port 36

38 AD8DVI-PB DVI-D Features: Support VIA VX800 series only. Connector: *DVI-D port. 37

39 AD3INLANG-PB Giga LAN Connectors Feature Integrated for 0/00/000 Mb/s full-and half-duplex operation. Wake on LAN * 3 support. Low-latency transmit and receive queues. Connector: Giga LAN Port x 3 38

40 AD8TV-PB RCA Video-out Connector S-Video Connector HDTV Connector VGA Connector Features: Support VIA VX800 IC series only. Connector: *VGA port; *HDTV connector; *S-Video connector; *RCA Video connector. 39

41 ADMPCIA-PB Mini-PCI Slot Slot: * mini-pci slot. 40

42 AD2VD-PB(20W DC/DC power module) 4

43 Function: 2Vdc input to ATX standard power supply. Input characteristics Range: 2 Vdc +- 5%. Current Max: 0A (max). Output characteristics Regulation Ripple Ripple & Noise Voltage load range min max max (mv) max (mv) Min Max +2V 0.5A 4A -5% +5% V 0.A A -5% +5% 50 5V 0.A 8A -5% +5% V A 0A -5% +5% VSB A 2A -5% +5% V NA NA NA NA NA NA Environment Operation temp. : 0-40 C. Operation Relative Humidity: 20% - 90%. Storage temp. : C. Storage Relative Humidity: 5% - 95%. Vibration: 0.38mm; 5-55Hz. Demission: 4X0 cm. 42