INSTALLATION & OPERATING MANUAL
|
|
- Chad Evans
- 6 years ago
- Views:
Transcription
1 INSTALLATION & OPERATING MANUAL IC 90 CHECK CONTENTS Package should contain.. Meter. Fixing Brackets (). Installation and Instruction Manual. The IC 90 meter is the latest kwh meter in the 900 series from Autometers Systems Ltd. It has been designed to be installed in switch board panels where space is a premium. Simple to install, small dimensions and ver y easy to programme makes it an ideal choice. THE INDICATOR LIGHTS There are two lights on the front of the meter which will illuminate at preset times subject to how you have programmed the meter. The top light is for engineering purposes and allows the meter to be checked for accuracy. The lower of the two lights will illuminate to indicate the output relay contacts closing. THE DISPLAY The meter has been designed to give limited but sufficient information for you to fit the meter and be confident it has been set up correctly. A new feature is the engineering display in which you can select test mode, this will show two decimal places on the display. Above you will see two pictures one showing the current ratio setting (000 ) which you have selected and the lower picture showing you the kwh display. Also on the lower picture are the numbers,,. These will only appear if a reverse phase is detected in one or all of the C Ts. PULSE OUTPUT The meter is fitted with an optically isolated volt free pulse output with contacts normally open. The meter has been designed to allow the installer to programme the output relay to either kwh/imp or 0 kwh/imp. The closure time of the contacts is 00 ms which makes the IC 90 meter suitable for nearly all management systems.
2 LOCATION The IC 90 meters should be mounted in a dr y, dirt free environment away from heat sources and ver y high electric fields. Temperatures should not exceed 70 C or fall below -0 C. INSTALLATION The meter should be mounted so that the front panel is vertical. A typical panel would be a switchgear cabinet door. The meter requires a depth behind the panel of 89 mm (including wiring). A single square aperture 9 mm wide, 9 mm high should be prepared. Enter the meter into the aperture and secure with the four fixing brackets provided. See diagram. PROGRAMMING THE METER To programme the meter you must first turn to the back of the meter and locate the binary switches. See diagram. Diagram (inset) shows the binar y switches which are situated on the back of the meter. These switches allow you to set the various parameters on the IC 90 meter. a. Switching the numbers - to the on position enables the meter to be programmed to various current ratio settings. See diagram. c. Switch 7 is for changing the pulse output relay value to either kwh/imp or 0 kwh/imp. The switch in the off position switches the pulse relay to kwh/imp. The switch in the on position switches the meter relay output to 0k Wh/imp. (For current ratio values of 000/ amp and above set this switch to on position). d. Switch 8 is for switching on the strobe light for accuracy testing. This switch must be in the off position when testing is complete. CURRENT TRANSFORMER SELECTIONS S ee diagram for the various ratios which can be selected by the binary switches. POWER ON When you have progammed and installed the meter you will be ready to put power on. When power is first put on the meter the display will go through a small routine. First it will illluminate all characters on the display ( seconds) then it will oscillate between the current ratio you have set and the kwh register. It will default to the kwh register after 60 seconds. b. Switch 6 allows the engineer to change the display to show two decimal places. Switch in the on position changes the display to show two decimal places. This switch must be in the off position when test is complete (no decimal places).
3 CONNECTION DIAGRAM Direction of Current S S L P S S L L P S S Neutral P Mains Load 0ma, 0 vac quickblow (f ) Position of the Binar y Switches. kwh Pulse Output DIAGRAM ELECTRICAL CONNECTIONS. sq mm wire is recommended for all electrical connections, subject to the distance between the meter and the current transformers. Phasing and polarity of the AC current and voltage connections and their relationship is critical to the correct operation of the unit.
4 MAINTENANCE The IC 90 meters do not require any regular maintenance. CURRENT TRANSFORMER SETTINGS The label below indicates the individual dill switch settings for the current transformer ratio: IMPORTANT The attention of the specifier, purchaser, installer and / or user is drawn to special measures and limitations or use which must be obser ved when these products are taken into ser vice to maintain compliance with the CE directives. / 0/ 60/ 00/ / 0/ 00/ 0/ 00/ 00/ 00/ 600/ 800/ 000/ 00/ 0/ 00/ 600/ 000/ 00/ 00/ DILL SWITCH POSITIONS FOR THE CURRENT RATIO SETTINGS ON MOVE DILL SWITCH "6" TO THE ON POSITION TO SHOW OFF TWO DECIMAL PLACES 000/ 00/ 000/ 000/ DIMENSIONS Four plastic fixing clips must be pushed against the metal face of the meter housing. DIAGRAM Please note. An aper ture of 9mm x 9mm must be cut into the metal face of meter housing for the meter to be mounted. Metal Face of Meter Housing 96 mm 90 mm 7 mm 89 mm 90 mm DIAGRAM
5 PERFORMANCE AND DATA Technical Parameters Meter standard BS EN 606 Accuracy Active.0 Reference Voltage x 0/00 volt Basic Current amp Maximum Current 6 amp Frequency 0/60 Hz Pulse Constant 000 imp/kwh Range of voltage 00v 0v Operating temperature - 0ºC + 0ºC Storage temperature - 0ºC + 70ºC Power consumption W volt DEFINITIONS Measurement Category CATIII Measurement categor y III is for measurements per formed in the building installation. Note examples are measurements on distribution boards, circuit breakers, wiring, including cables, bus-bars, junction boxes socket-outlets in the fixed installation, and equipment for industrial us and some other equipment, for example, stationar y motors with permanent connection to the fixed installation. Table symbol, IEC Defined as: Insulation comprising both basic insulation and supplementary insulation. Double Insulation Symbol! Caution, risk of electric shock MAINTENANCE AND SERVICE Field Service Considerations In the unlikely event that a unit should fail, it will generally be ser viced by exchanging the unit for a replacement unit. The initial installation should be done in a way which makes this as convenient as possible.. It is good practice that a current transformer shorting block is fitted, this enables the meter to be disconnected without open circuiting the current transformers. The shorting block should be wired so that the protective relays are not affected.. All wiring should be routed to allow easy removal of the connection to the terminals. Disconnect From Supply A suitable isolator for both voltage and current terminals shall be included in the wiring installation, close to the meter with easy access and marked as the meters disconnect device. If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. Current measuring terminals are not intended to be connected to voltages to earth above 0Vac.
6 DEDICATED CUSTOMER SERVICE Customer care is the cornerstone of the company s success. A positive ser vice policy is obser ved throughout every specialist area of operation. The personal involvement of all the directors at ever y level, a highly trained and motivated staff, fully computerised systems and in depth stockholding combine to provide a level of ser vice which has earned the appreciation of customers across the spectrum of the UK and overseas markets. Computerised distribution systems are geared to a consistent hour despatch of products, with 0 minute despatch being possible in response to urgent demand for small orders. PRODUCT RANGE Metering and monitoring equipment ranges from single phase and Polyphase kwh electromechanical meters to a sophisticated range of fully programmable information centres. Also available are Electronic Meters, Panel Mounted Meters, Maximum Demand Meters, DIN Rail Meters and Current Transformers. CE Approval. The IC 90 has been fully examined and tested in accordance with the standards listed and meets the specified requirements defined in BS EN 66:997 inc A, A, A - Electrical equipment for measurement, control and laboratory use - EMC requirements.. BS EN 66:997 inc. A, A & A Conducted Emissions. BS EN 66:997 inc. A, A & A Radiated Electricity Field Emissions. BS EN :99 inc. A & A Electromagnetic Compatibility. BS EN :00 inc. A & A Electromagnetic Compatibility. BS EN :99 inc. A & A Electromagnetic Compatibility Safety Standards: BS EN 600-:00 Important. The attention of the specifier, purchaser, installer or user is drawn to special measures and limitations to use which must be observed when these products are taken into service to maintain compliance with the CE directives. Details of these special measures and limitations of use are available from HMSO. REF: IEC 000--(BS9/0788DC) IEC (BS 9/6DC) IEC (BS 9/0789DC). WARNING DO NOT MEGGAR TEST Autometers Systems Limited, B Albany Road, Chorlton-cum-Hardy, Manchester. M 0AW Tel: + (0) Fax: + (0) sales@autometers.co.uk Product development is continuous and Autometers Systems Ltd reser ves the right to make alterations and manufacture without notice. Products as delivered may therefore differ from the descriptions and illustrations in this publication. Publication: 07.IC90.D.0
MultiCube Single Phase Multi-Function Electricity Meter. Installation and Operation
MultiCube Single Phase Multi-Function Electricity Meter Installation and Operation PREFACE MultiCube Single Phase Meter Operating Guide Revision 5.01 August 2002 This manual represents your meter as manufactured
More informationSPM91 DIN Rail Single Phase Energy Meter Installation & Operation Manual V1.0
SPM91 DIN Rail Single Phase Energy Meter Installation & Operation Manual V1.0 ZHUHAI PILOT TECHNOLOGY CO., LTD. I Danger and warning! This device can be installed only by professionals. The manufacturer
More informationMetering Devices IQ 300
Effective: May 2001 Page 1 New Information Contents Description Page General Description......... 2 Specifications.............. 3 Field Wiring Connections.... 4 Page 2 Effective: May 2001 Applications
More informationSDM120 SERIES. SDM120 series User Manual. Single phase two wire DIN rail energy meter (One module)
SDM120 SERIES Single phase two wire DIN rail energy meter (One module) User manual ------------ 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic errors 1.6 Dimension
More informationCOUNTIS ATv2/ATiv2 GB
COUNTIS ATv/ATiv GB Operating instructions Industrial Switching & Protection Systems SOCOMEC - Ref. : D ENGLISH GB Contents PRELIMINARY OPERATIONS GENERAL INFORMATION PRESENTATION INSTALLATION CONFIGURATION
More informationDigital Frequency Divider INSTRUCTION MANUAL CONTENTS. 1. Working Principle Installation Setting Up Technical Data 4.
Digital Frequency Divider INSTRUCTION MANUAL CONTENTS 1. Working Principle 2 2. Installation 2 3. Setting Up 3 4. Technical Data 4 Code: 189/1a 1 WORKING PRINCIPLE The DFD has been designed to generate
More informationMini Digital Multimeter
User's Guide Mini Digital Multimeter Model MN15 99 Washington Street Melrose, MA 02176 Phone 781-665-1400 Toll Free 1-800-517-8431 Visit us at www.testequipmentdepot.com Back to the Extech MN15/MN16 Series
More informationMETERSUK. SmartLink D Y N A M i T E. 3 MOD CT Series. User Manual KEY FEATURES INDEX 3. TECHNICAL DESCRIPTION.
LTD METERSUK sales@meters.co.uk 01524 555 929 3 MOD CT Series Smart Energy Meter KEY FEATURES Three phase metering Three Phase metering, 7 din modules Accuracy class 1 according to IEC62053-21 LCD display,
More informationDM-918 OPERATIONS MANUAL AUTORANGING MULTIMETER
DM-918 OPERATIONS MANUAL AUTORANGING MULTIMETER SAFETY INFORMATION The following safety information must be observed to ensure maximum personal safety during the operation of this meter: This meter is
More informationAVC 2 AUTOMATIC VOLUME CONTROL USERS MANUAL
AVC 2 AUTOMATIC VOLUME CONTROL USERS MANUAL GENERAL DETAIL The AVC2 will control a stereo channel to a preset maximum output level allowing the maximum sound level of a system to be controlled. The AVC2
More informationAvanti HP Series Centrifuges Preinstallation
J3HP-TB-001AC May 2009 Avanti HP Series Centrifuges Preinstallation INTRODUCTION Purchase of an Avanti HP series high performance centrifuge includes installation and Basic Instrument Training for two
More informationSee instructions to download and install the latest version of LinkBoxLON and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationMiG2 CONTROLLERS. 2 & 4 Stage General Purpose Controllers, with Air-conditioning Facilities
MiG2 CONTROLLERS 2 & 4 Stage General Purpose Controllers, with Air-conditioning Facilities The MiG2 controllers incorporate: 2 Inputs (Configurable as Resistive, 0 10V, 0 20mA or 4 20mA) 2 or 4 Relay Outputs
More informationRhino Buffer Module PSM24-BFM600S. Operating Instructions
Rhino Buffer Module PSM24-BFM600S Operating Instructions RHINO BUFFER MODULE PSM24-BFM600S Description The PSM24-BFM600S Buffer Module will hold the output voltage of a 24 VDC power supply after brownouts
More information93 SERIES. Timed socket for 34 series 93.68/93.69
93 93 Slim timed sockets for 34 series, 6.2 mm wide Timer adjustment via top mounted rotary knob accessible after assembly Control signal terminal DIP-switch for selection of 4 time scales and 8 functions
More informationAdvantages of a Full Featured 700 Series Relay
SECTION 1 Advantages of a Full Featured 700 Series Relay Since the launch of the 700 series relays in 2000, this product line has continuously evolved both functionally and visually. The 700 series product
More informationMTP INSTRUCTION MANUAL
DT-118B MTP INSTRUCTION MANUAL Pocket Autoranging Digital Multimeter 3 in 1 Model MTP-1025 Auto Ran ging DMM Hz% A OFF V AU TO PO WER OFF MTP Instruments Table of Contents Introduction Page 1 Features
More informationOperating instructions. Switching amplifier DN0210 DN / / 2015
Operating instructions Switching amplifier DN0210 DN0220 UK 80011079 / 00 01 / 2015 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5
More informationSee instructions to download and install the latest version of LinkBoxEIB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationLXEM145 SERIES Lanx Australis single Phase KWh Meter 45Amp. User manual
LXEM145 SERIES Lanx Australis single Phase KWh Meter 45Amp Single phase two wire DIN rail energy meter (One module) 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic
More informationOB735 Smart Energy Meter
User Manual Revision 3.002 English OB735 Smart Energy Meter Benefits and Main Features Three phase metering Standard DIN rail Format (DIN43880) CI.1 Accuracy (EN50470) Energy consumption LED Isolated pulse
More informationEXPANSION PERIPHERAL CVM-R10 C. (Code ) INSTRUCTION MANUAL ( M / 00 A ) (c) CIRCUTOR S.A.
EXPANSION PERIPHERAL CVM-R10 C (Code 7 70 217 ) INSTRUCTION MANUAL ( M 981 170 / 00 A ) (c) CIRCUTOR S.A. ------ CVM-R10 C Peripheral --------------- Pag. 1 CVM-R10C EXPANSION PERIPHERAL 1.- DESCRIPTION
More informationTable of Contents. Safety. Attention. Warnings
Solstart Miniature Soft Starter 8-58A, 220-600V Instruction Manual Ver. 21.2. 2002 Table of Contents Page Subject 3 Starter Selection 4 Installation Notes 5 Wiring 6 Starter Settings & Start-up Procedure
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Uni-I/O Modules Installation Guide UID-0808R, UID-0808T, UID-1600,UID-0016R, UID-0016T Uni-I/O is a family of Input/Output modules that are compatible with the UniStream control platform. This guide provides
More informationekorrps MULTIFUNCTIONAL PROTECTION UNIT CONFIGURATION AND GENERAL CHARACTERISTICS LIB
MO-067-EN Operation Manual MULTIFUNCTIONAL PROTECTION UNIT CONFIGURATION AND GENERAL CHARACTERISTICS LIB Transformer Substations Secondary Distribution Switchgear Primary Distribution Switchgear Protection
More information407B 1/16 DIN Multi-Mode Timer
< Marsh Bellofram Group of Companies < Automatic Timing & Controls < Timer < 407B Series Downloadable Files: 407B Series 407B 1/16 DIN Multi-Mode Timer Selectable On-Delay/Off-Delay/Interval Timing Modes
More informationOPERATING INSTRUCTION
OPERATING INSTRUCTION AUTORANGING MULTIMETER MAX Ω F C 10A MAX every 15 min. COM V SAFETY INFORMATION The following safety information must be observed to insure maximum personal safety during the operation
More informationSafegard V4 Panel. Installation Datasheet. Safegard V4 Panel Installation Instructions and Datasheet release 1.7 August 2016
Safegard V4 Panel Installation Datasheet ELECTROSTATIC SENSITIVE DEVICE This product forms part of a life safety system. Failure to correctly store, handle, install and maintain the product will directly
More informationEM3/../ODIN Three Phase Electricity Meters
Data Sheet EM3/../ODIN Three Phase Electricity Meters EM3/../ODIN Three Phase Electricity Meters Trend code Supplier's code EM3/230/D/ODIN OD4165 EM3/230/CT/ODIN OD4110 ACC/EM3/ODIN/PANELKIT 09 811 84
More informationSee instructions to download and install the latest version of LinkBoxMB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Uni-I/O Wide Modules Installation Guide UID-W1616R, UID-W1616T Uni-I/O Wide is a family of Input/Output modules that are compatible with the UniStream control platform. Wide Modules are 1.5 times as wide
More informationVEO. V2PF480Y/277VSY01 Art.Nr.: V2PF480Y/277VSY01P Art.Nr.: TECHNICAL DATA
Monitoring of phase sequence and phase loss Monitoring of asymmetry Supply voltage 208-480 V AC Supply circuit = measuring circuit 1 change-over contact Width 22,5 mm Control elements Asymmetry Status
More informationQXA2000 QXA2001. Condensation Monitor QXA2001 QXA2000 AQX2000
1 542 1542P03 1542P01 1542P02 QXA2001 QXA2000 AQX2000 Condensation Monitor QXA2000 QXA2001 The QXA2000 condensation monitor is used to avoid damage due to condensation on chilled ceilings and in HVAC plant.
More informationIndustrial 5-Port Fast Ethernet Switches. with SFP Slot and optional 4 PoE PSE Ports. Basic Model: KSD-541. PoE Model: KSD-541-HP. Installation Guide
Industrial 5-Port Fast Ethernet Switches with SFP Slot and optional 4 PoE PSE Ports Basic Model: KSD-541 PoE Model: KSD-541-HP Installation Guide DOC.141201-1- (C) 2014 KTI Networks Inc. All rights reserved.
More informationSee instructions to download and install the latest version of LinkBoxEIB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationPanelView Plus/VersaView CE Terminals and Display Modules
Installation Instructions PanelView Plus/VersaView CE Terminals and Display Modules (Catalog Numbers 2711P-xxxxxx, 6182H-xxxxxx) English Inside: Overview...2 For More Information...2 Modular Components...3
More informationAutoranging True RMS Multimeter User Manual
Autoranging True RMS Multimeter User Manual Please read this manual before switching the unit on. Important safety information inside. Contents Page 1. Safety Information... 4 2. Safety Symbols... 5 3.
More informationRTU500 series Data Sheet Power Supply CP-E 24/2.5
Data Sheet Power Supply CP-E 24/2.5 Power Supply CP-E 24/2.5 Application The primary switch mode power supply offers two voltage input ranges. This enables the supply with AC or DC. Furthermore it is equipped
More informationSee instructions to download and install the latest version of LinkBoxMB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationVEO. V2ZR V AC/DC Art.Nr.: V2ZR10P V AC/DC Art.Nr.: TECHNICAL DATA
Off-Delay 10 time ranges Supply voltage 24-240V AC/DC 1 change-over contact Width 22,5 mm Control elements Fine adjustment Setting of time range Status indication LED U/t: Supply voltage LED R: Relay status
More informationGS400. Electronic Auto-Ranging DIN Panel Mounted Positioner
GS400 Electronic Auto-Ranging DIN Panel Mounted Positioner Features * AC (115/230V) and DC (24V) versions available. * Accepts either current or voltage command signal and either current, voltage, or three
More informationSmart Energy Meter. Benefits and Main Features. User Manual Revision English OB (100)A
User Manual Revision 2.001 English Smart Energy Meter OB737 0.5-10(100)A Benefits and Main Features Three phase metering Standard DIN rail Format (DIN43880) EN50470-3 Class B. IEC62053-21 Import & Export
More informationSwitching module for AC V and up to three load stages, with manual switching
8 149 PTM13-M3 DESIGO I/O modules Switching module for AC 24 250 V and up to three load stages, with manual switching PTM13-M3 Signal converter for connection to P-bus, with three interlocked on/off control
More information170 ADM to 60 VDC Module Base / 170 ADO Pt. Relay Out Module Base. Version 1.0
170 ADM 850 10 10 to 60 VDC Module Base / 170 ADO 830 30 6 Pt. Relay Out Module Base Version 1.0 31005197 00 Safety Information NOTICE Read these instructions carefully, and look at the equipment to become
More informationMessaging module CP-C MM
2CDC 271 087 F0t04 Features Pluggable onto CP C range primary switch mode power supplies REMOTE OFF input to switch off the power supply unit remotely Monitoring of the input voltage of the power supply
More informationCU USB-Extender-Rx (USB and DVI Extender) Version: 0.3 Date:
CU8860-0000 USB-Extender-Rx (USB and DVI Extender) Version: 0.3 Date: 2006-02-20 Table of Contents Table of Contents 1 Foreword 1 1.1 Notes on the documentation 1 1.1.1 Liability Conditions 1 1.1.2 Conditions
More informationPRO-1250D CT MID DIN rail three phase four wire energy meter.
PRO-1250D CT MID DIN rail three phase four wire energy meter. 1.1 Safety instructions 1.2 Foreword 1.3 MID certificate 1.4 Performance criteria 1.5 Specifications 1.6 Basic errors 1.7 Description 1.8 Dimensions
More informationAI561 Analog Input Module
Ordering Data DATA SHEET AI561 Analog Input Module 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1TNE 968 902 R1101 AI561, analog input module, 4 AI, U/I 1TNE 968 901 R3101 1TNE 968
More informationSee instructions to download and install the latest version of LinkBoxEIB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationVFI RTG PDU 6-10K. Installation and user manual. Service and support: Call your local service representative
VFI RTG PDU 6-10K Installation and user manual Service and support: Call your local service representative SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. This manual contains important instructions that
More informationMini Digital Multimeter
User Manual Mini Digital Multimeter Model MN15A Additional User Manual Translations available at www.extech.com Introduction Congratulations on your purchase of the Extech MN15A MultiMeter. The MN15A offers
More informationINSTALLATIONSANVISNING INSTALLATION MANUAL INSTALLATIONS ANLEITUNG MANUEL D INSTALLATION RD-48 LV/HV. RS-422/485 Repeater Répéteur RS-422/485
LV/HV INSTALLATISANVISNING INSTALLATI MANUAL INSTALLATIS ANLEITUNG MANUEL D INSTALLATI Westermo Teleindustri AB 2004 REV. C Galvanic Isolation Transient Protection Balanced Transmission CE Approved RS-422/485
More informationPRO-75 SERIES. User manual
PRO-75 SERIES DIN rail single phase two wire energy meter 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic errors 1.6 Description 1.7 Dimensions 1.8 Installation
More informationUser's Guide. Phase Sequence and Motor Rotation Tester Model
User's Guide Phase Sequence and Motor Rotation Tester Model 480403 Introduction Congratulations on your purchase of the Extech Model 408403 Motor and Phase Rotation Indicator. This handheld instrument
More informationDATA SHEET. Advanced Energy Meter, AEM 380 & AEM 305
DATA SHEET Advanced Energy Meter, AEM 380 & AEM 305 Easy installation MID-approved 5 optional communication interfaces Phase error detection Low power consumption Two tariffs Two-pulse output DEIF A/S
More informationUser's Guide. Digital Multimeter. Model MN42
User's Guide Digital Multimeter Model MN42 Introduction Congratulations on your purchase of the Extech MN42 MultiMeter. The MN42 offers AC/DC Voltage, DC Current, and Resistance testing. Proper use and
More informationSolid-state Timer. Ordering Information. Miniature Timer with Multiple Time Ranges and Multiple Operating Modes H3YN- - Accessories (Order Separately)
Solid-state Timer Miniature Timer with Multiple Time Ranges and Multiple Operating Modes Minimizes stock. Pin configuration compatible with MY Power Relay. Standard multiple operating modes and multiple
More informationTU531, TU532 Terminal Unit
Ordering Data DATA SHEET TU531, TU532 Terminal Unit 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 217 200 R0001 1SAP 217 000 R0001 1SAP 417 000 R0001 TU531, terminal unit, 230 VAC,
More informationETD-BL-1T-230(-PT) Multifunctional time relay with various functions and adjustable times. Data sheet. 1 Description
(-PT) Multifunctional time relay with various functions and adjustable times Data sheet 106395_en_02 PHOENIX CONTACT 20-06-08 1 Description Requirements pertaining to safety and system availability increase
More informationIndustrial Serial RS-232 to Fiber Converter. KSC-200 Series. Installation Guide
Industrial Serial RS-232 to Fiber Converter KSC-200 Series Installation Guide DOC.100803-KSC-200-1- (C) 2006 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any
More informationINSTALLATION DKM-409 NETWORK ANALYSER WITH HARMONIC MEASUREMENT AND SCOPEMETER. Before installation:
DKM-409 NETWORK ANALYSER WITH HARMONIC MEASUREMENT AND SCOPEMETER The DKM-409 is a precision instrument designed for displaying various AC parameters in 3-phase distribution panels. Thanks to its isolated
More information5.1. Motor Protection and Monitoring. Contents. Product Overview. Monitoring Relays. D64R Series Digital Ground Fault Relays...
.1 Ground Fault Relays and Monitors Contents Description Current.................. Phase................... Voltage.................. Ground Fault Relays and Monitors D64R Series Digital Ground Fault Relays....
More informationIndustrial 5-Port Fast Ethernet Switches with SFP Slot and optional 4 PoE PSE Ports. Basic Model: KSD-541 PoE Model: KSD-541-P. Installation Guide
Industrial 5-Port Fast Ethernet Switches with SFP Slot and optional 4 PoE PSE Ports Basic Model: KSD-541 PoE Model: KSD-541-P Installation Guide DOC.080104-1- (C) 2008 KTI Networks Inc. All rights reserved.
More informationBS 181 SINGLE CHANNEL POWER SUPPLY USER MANUAL
BS 181 SINGLE CHANNEL POWER SUPPLY USER MANUAL August 2016 This product is designed and manufactured by: ASL Intercom B.V. Zonnebaan 42 3542 EG Utrecht The Netherlands Phone: +31 (0)30 2411901 Fax: +31
More informationOperating instructions. Speed monitor D / / 2014
Operating instructions Speed monitor D200 80005257 / 00 05 / 2014 Contents 1 Preliminary note...4 1.1 Symbols used...4 1.2 Warning signs used...4 2 Safety instructions...5 2.1 General...5 2.2 Target group...5
More informationPRODUCT. Battery Charger
PRODUCT Battery Charger Model : BC 9080 Battery Charger The ICD Battery Charger is designed to supply required DC Voltage and Current to the connected load and recharge the Battery on boost charging over
More informationRedundancy unit CP-A RU
2CDC 271 010 F0t06 Features Decoupling of CP power supply units with 2 inputs, each up to 20 A per input / channel Output up to 40 A True redundancy by 100 % decoupling of two parallel connected power
More informationVEO. V2UF230V10 Art.Nr.: TECHNICAL DATA
Continous voltage monitoring Mains fluctuation detection Detects voltage drop / short interruptions of at least 10ms Prevents undefined states in switching and control systems Generates reset pulse after
More informationPart No. Description Product Life Cycle Phase *) unit, 24 VDC, spring terminals. unit, 24 VDC, spring terminals, XC version
Ordering Data DATA SHEET TU520 Terminal Unit 1 Ordering Data Part No. Description Product Life Cycle Phase *) 1SAP 214 400 R0001 1SAP 414 400 R0001 TU520-ETH, PROFINET I/O terminal unit, 24 VDC, spring
More informationISIO 200. Binary Input/Output (I/O) terminal with IEC interface
ISIO 200 Binary Input/Output (I/O) terminal with IEC 61850 interface Compact and easy ISIO 200 Put your Binary I/Os where you need them ISIO 200 is a simple and versatile binary I/O terminal with IEC 61850
More informationOperating instructions. Standstill monitor A / / 2011
Operating instructions Standstill monitor A300 UK 1 2 3 4 5 6 7 8 7390337 / 01 02 / 2011 1 2 3 4 5 6 7 8 switchpoint min max pulse/min power Made in Germany ifm electronic gmbh D 45127 Essen func. I II
More informationADC7520 SERIES. 1600W Battery Chargers and Power Supplies
ADC7520 SERIES 1600W Battery Chargers and Power Supplies Wide output adjustment range 0 72VDC Analog control by external 0-5VDC voltage Temp.comp charging, sense as on option Power fail relay alarm Master-Slave
More informationElectronic timer CT-VWD Impulse-ON with 1 c/o contact Data sheet
Electronic timer CT-WD 2CDC 251 003 F0003 CT-WD 6 5 1 2 3 4 1 7 selectable time ranges, from 0.05 s to 100 h, for the adjustment of the pulse time 2 Potentiometer with direct reading scale for the fine
More informationArtistic Licence. Rail-Switch II. User Guide. Rail-Switch II User Guide. Version 5-5
Artistic Licence Rail-Switch II User Guide Version 5-5 Please read these instructions before using the product. This product has been designed & manufactured for professional use only. It should only be
More informationSLIMCON-6 24V DC POWERED ISOLATING SIGNAL CONVERTER
SLIMCON-6 24V DC POWERED ISOLATING SIGNAL CONVERTER Whilst every effort has been taken to ensure the accuracy of this document, we accept no responsibility for damage, injury, loss or expense resulting
More informationInstallation Instructions
Installation Instructions (Cat. No. 1794-PS1) 1 2 3 4 5 7 6 Component Identification 1 Supply module 1794-PS1 2 Indicator 3 120/230V ac ground 4 120/230V ac common L2/N connections 5 120/230V ac power
More informationUSP-070-B08 USP-104-B10, USP-104-M10 USP-156-B10
UniStream HMI Panel Installation Guide USP-070-B10, USP-070-B08 USP-104-B10, USP-104-M10 USP-156-B10 Unitronics UniStream platform comprises control devices that provide robust, flexible solutions for
More informationDRT-301 A/D. User manual. Three phase four wire DIN rail energy meter. (Seven modules) 1.1 Safety instruction. 1.2 Foreword. 1.3 Performance criteria
DRT-301 A/D Three phase four wire DIN rail energy meter (Seven modules) 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic errors 1.6 Structure Diagram 1.7 Dimensions
More informationMultifunction Transducer MT440
Multifunction Transducer MT440 Voltage and current auto range measurements up to 600V, 12.5A Universal wide auxiliary power supply range 24 300 Vdc, 40 276 Vac Power accuracy class 0.5 (EN 60 688), Up
More informationProduct and Applications Description. Example of Operation. Installation Instructions WARNING. Note. Application Programs
Product and Applications Description Example of Operation dimmer UP 525/11 load circuit AC 230 V L1 N The dimmer UP 525/11 is a dimming actuator for mounting in box mounts (a.o. 60 mm Ø, 60 mm depth).
More informationINSTALLATION MANUAL. LC 200 Electronic Overload Guard. Software versione PW0501 R 0.3
INSTALLATION MANUAL LC 200 Electronic Overload Guard Software versione PW0501 R 0.3 CONTENTS MAIN FEATURES LC 200 TECHNICAL FEATURES Page 2 SYMBOLS Page 3 WARNINGS Page 3 IDENTIFICATION DATA PLATE Page
More information7511 / / / 711 / / 731 / Preset 27
22 Timers Timers Electronic 23 7511 / 3410 23 6320 / 720-6300 24 ElectRo-MeCH 25 710 / 711 / 720 25 722 / 731 / 732 26 Preset 27 7932 27 Electronic 23 7511 Series 8 digit self powered LCD electronic timer
More informationDuris E5 PowerFlex LED Strips 25mm LED Pitch
Duris E5 PowerFlex LED Strips 25mm LED Pitch ILX-E525-xx08-6000-SD2xx Product Overview The PowerFlex range are densely populated, high bright, flexible LED strips using the Osram Duris E5 LED at its heart.
More informationEX-RC1 Remote I/O Adapter
EX-RC1 Remote I/O Adapter The EX-RC1 interfaces between Unitronics Vision OPLCs and remote I/O Expansion Modules distributed throughout your system. The adapter is connected to a PLC via CANbus. Each adapter
More informationSwitched Mode Power Supply Operating manual PAP800
Features: Switched mode power supply Wide output 0 144Vdc Analog control by an external 0 5Vdc Power failure alarm output Master-slave connection Powerfinn PAP series is a high power, lightweight, advanced
More informationWhen any of the following symbols appear, read the associated information carefully. Symbol Meaning Description
Uni-I/O Wide Modules Installation Guide UIS-WCB1 Uni-I/O Wide is a family of Input/Output modules that are compatible with the UniStream control platform. Wide Modules are 1.5 times as wide as Uni-I/O
More informationSTUDIO 1800 OPERATING INSTRUCTIONS MANUFACTURED IN THE UK
STUDIO 1800 OPERATING INSTRUCTIONS MANUFACTURED IN THE UK The Studio 1800 is a combined Programmer and Temperature Controller which has been specifically designed for use with pottery kilns. Control of
More informationProduct and Applications Description. Application Programs. Note. instabus EIB Technical Product Information. June 2005
Product and Applications Description Application Programs The application programs of the dimmer UP 525/01 consist of two elements: the actuating and the sensor program element. The tasks actuating program
More informationSafety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationMultifunctional time delay relay MFT U31S, MFT U41SE
8 Functions, 8 time ranges Multivoltage: 24 Vac / dc 110... 240 Vac 2 output contacts MFT U31S Functions E Delay on E Delay on - version with control contact as opening contact A Delay off without auxiliary
More informationSee instructions to download and install the latest version of LinkBoxMB and the user's manual at
Safety Instructions WARNING Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and also may damage seriously the IntesisBox and/or any
More informationDIN Series MINIATURE CIRCUIT BREAKERS, RESIDUAL CURRENT CIRCUIT BREAKERS. Introducing the DIN Series High-quality, high-performance circuit breakers
DIN Series MINIATURE CIRCUIT BREAKERS, RESIDUAL CURRENT CIRCUIT BREAKERS Introducing the DIN Series High-quality, high-performance circuit breakers Features (1) All models fully comply with IEC regulations
More information78 Series Electromechanical Relay Selection Guide
78 Series Electromechanical Relay Selection Guide Specification 781 Series 782 Series 783 Series 784 Series Coil Voltages Configuration SPDT DPDT 3PDT 4PDT Contact Rating 15A 15A 15A 15A Base Socket 5
More informationTraceTek Leak Detection Master Module Installation Instructions TOOLS REQUIRED STORAGE
TTDM-128 TraceTek Leak Detection Master Module Installation Instructions TRACETEK APPROVALS AND CERTIFICATIONS TYPE NM General Signaling Equipment 76LJ GENERAL INFORMATION Please read these instructions
More informationPV Rapid Shutdown device
PV Rapid Shutdown device Installation and Operation Manual Solis-RSD-1G(1:1) Solis-RSD-1G(2:2) Manufacturer: Ginlong (Ningbo) Technologies Co.,Ltd., Ningbo, Zhejiang, P.R.China US Office: 565 Metro Pl.
More informationImpulse switching module
8 156 PTM14250A-P DESIGO I/O modules Impulse switching module PTM14250A-P for AC 24250 V, single-stage, with manual switches, double module Signal converter for connection to P-bus and for delivering impulse
More informationS-14 S-14. Compact Digital Multimeter. Compact Digital Multimeter
S-14 Compact Digital Multimeter S-14 Compact Digital Multimeter SAFETY INFORMATION The following safety information must be observed to insure maximum personal safety during the operation at this meter
More informationDKM-405 NETWORK ANALYSER WITH TOTAL HARMONIC DISTORTION DISPLAY
datakom@datakom.com.tr http://www.datakom.com.tr Tel: +9-216 466 84 6 Fax: +9-216 364 65 65 DKM-45 NETWORK ANALYSER WITH TOTAL HARMONIC DISTORTION DISPLAY INTRODUCTION The DKM-45 is a low cost precision
More informationCU port USB 2.0 hub. Version: 1.1 Date:
CU8004-0000 4 port USB 2.0 hub Version: 1.1 Date: 2006-08-11 Table of Contents Table of Contents 1 Foreword 1 1.1 Notes on the documentation 1 1.1.1 Liability Conditions 1 1.1.2 Conditions of delivery
More informationLED Driver Linear / area fixed output
Driver LC W /3/3/7/mA fixc lp SNC ESSENCE series Product description Fixed output built-in LED Driver Constant current LED Driver Output current, 3, 3, 7 or 1, ma Max. output power W For luminaires of
More information