COUNTIS ATv2/ATiv2 GB
|
|
- Caroline Beasley
- 5 years ago
- Views:
Transcription
1 COUNTIS ATv/ATiv GB Operating instructions Industrial Switching & Protection Systems
2 SOCOMEC - Ref. : D
3 ENGLISH GB Contents PRELIMINARY OPERATIONS GENERAL INFORMATION PRESENTATION INSTALLATION CONFIGURATION TECHNICAL CHARACTERISTICS SOCOMEC - Ref. : D
4 PRELIMINARY OPERATIONS For personnel and product safety please read the contents of these operating instructions carefully. Check the following points as soon as you receive the package: the packing is in good condition, the product has not been damaged during transit, the product reference number conforms to your order, the package contains the product as well as the operating instructions. GENERAL INFORMATIONS The COUNTIS System comprises energy metering products for balanced or non-balanced - or -wire network. This system comprises two products: ATv: a non-insulated three-phase active energy-meter, which does not allow earthing CT of secondary. ATiv: a three-phase insulated single or double rate active energy meter allowing the CT secondary to be earthed. These products are completely configurable (CT radio, network type and pulse output value) and have a -digit display which allows direct display of consumption in kwh. They are equipped with a pulse output as standard. PRESENTATION COUNTIS ATv / ATiv SINGLE RATE COUNT 0 A kwh display Total and partial meter display, or scrolling parameter settings Flashing LED consumption indicator (0 Wh/pulse) Validation/scrolling of parameter settings SOCOMEC - Ref. : D
5 PRESENTATION (continued) COUNTIS ATiv DOUBLE RATE ENGLISH COUNT B kwh display Total and partial meter display, or scrolling parameter settings Displays t and t rate meters Flashing LED consumption indicator (0 Wh/pulse) Validation/scrolling of parameter settings INSTALLATION The COUNTIS can be installed on a DIN EN 00 rail (DIN 0). Recommendation: Avoid close proximity with systems generating electromagnetic disturbances Avoid vibrations including accelerations of more than G for frequencies lower than 0 Hz. The minimum torque for the fixed terminal is 0. Nm. CLIMATIC ENVIRONMENT To guarantee optimum operation, it is recommended that this device is used between - to + C with a relative humidity of between 0 and %. CONNECTION The Countis ATv and ATiv consist of connection terminals of to mm for currents and voltages. SAFETY INSTRUCTIONS (U, I, F) Recommendation: We recommend that the auxiliary voltage and the voltage inputs should be protected with 0. A fuses or BS A gg. To avoid damaging the device, take care to observe the following before connecting the device: indications on the casing, network frequency: 0 or 0 Hz, maximum permanent voltage at voltage input terminals of 00 V AC ± 0% phase/phase, maximum permanent current of A (connection from current transformer(s)). SOCOMEC - Ref. : D
6 INSTALLATION (continued) NETWORK If the current is badly connected or there is poor current/voltage correspondence (negative energy) the counter will be stopped and the arrows flash. CT earthing, for the ATiv only WIRE WITH CT ( BL) WIRE WITH CT ( BL) L L L P S L L L N P S ATiv ATiv COUNT 0 C COUNT 0 C WIRE WITH CT ( NBL) WIRE WITH CT ( NBL) L L L P S P S L L L P S P S ATiv ATiv COUNT 0 C COUNT 0 C WIRE WITH CT ( NBL) WIRE WITH CT ( NBL) L L L P S P S P S ATiv L L L N P S P S P S ATiv Key to diagrams: Fuses 0. gg or BS A gg COUNT 0 C COUNT C TWO-PHASE ( BL) L L P S ATiv COUNT C COUNT C SINGLE-PHASE ( BL) L N P S ATiv RATE INPUT (t / t) CONNECTING PULSE OUTPUT The neutral has to be connected for the dual tarif ATiv. COUNT A t = 0 VAC t = 0 VAC 0 COUNT B GB External counter External power supply 0 SOCOMEC - Ref. : D
7 CONFIGURATION The device will automatically leave the configuration menu if no buttons are pressed for a period of seconds. Press the button for a prolonged period to scroll rapidly through the configuration screens. Press for a short period to scroll through each screen one-by-one. KEY + INSTRUCTION For seconds to access access-code entry (CdE). To enter code. To validate the code and access to the network programming (net). To select the network type, bl (single phase), bl (two-phase), - nbl (unbalanced three-phase) and - bl (balanced three-phase). ENGLISH To validate the network programming and go on to the current transformer (CT) primary value. A long press on the button causes rapid scrolling and a single short press causes scrolling in steps of. To programme the primary value up to 000 A. To validate the unit programming and go on to the pulse output (PuLSES). To go on to the weight of this output (VAL). The values available depend on the Ct ratio. To select the weight 0. for 0. kwh, for kwh, 0 for 0 kwh, 00 for 00 kwh. To validate the programming of this weight and go on to the pulse duration (dur). To select the duration from 0 to 00 ms. To accept value and pass to partial meter zero reset (rset). To select rset no (no reset to zero) and rset YES (reset to zero). To confirm reset to zero and return to network type programming. + To confirm and quit programming. SOCOMEC - Ref. : D
8 TECHNICAL CHARACTERISTICS ENCLOSURE Connection Weight Size Protection class (front) via to mm terminal shrouds 00 g modular: modules of. mm IP0 FRONT PANEL Green LCD/ digits Digit height x mm INPUTS The current inputs are insulated on the ATiv. CURRENT Via transformer with configurable primary secondary Input consumption Consumption to 000 A A 0 ma to A (secondary) VA TENSION Measurement range (Line/Line) 0 V AC - % to 00 V AC + 0% Consumption 0, VA The Countis ATv and ATiv are autopowered from the V et V voltage inputs. AUXILIARY POWER SUPPLY Type Consumption ACCURACY auto-powered VA Accuracy index IEC 0 class PULSE OUTPUT Reed relay (00 V DC - 0. A - VA) Pulse duration Maximum tripping number 0 to 00 ms x 0 at 0 V DC/0 ma OPERATING CONDITIONS Operating temperature - C up to C Storage temperature - 0 C up to 0 C Relative humidity % STANDARDS CE marking IEC 000-/ EN 00- EN 00- Operating conditions IEC 00-- IEC 00-- IEC SOCOMEC - Ref. : D
9 SOCOMEC - Ref. : D ENGLISH
10 SOCOMEC - Ref.: D - 0/0 COUNT C HEAD OFFICE SOCOMEC GROUP Switchgear and UPS S.A. capital de 0 00 R.C. Strasbourg 00 B SOCOMEC, rue de Westhouse - B.P. 0 F- Benfeld Cedex- FRANCE Tel. + (0) - Fax + (0) SALES MANAGEMENT DIVISION SOCOMEC, rue Pierre Grange F- Fontenay-sous-Bois Cedex-FRANCE Tel. + (0) 0 - Fax + (0) scp.dcm@socomec.com Industrial Switching & Protection Systems This document is not contractual. SOCOMEC reserves the right to modify features without prior notice in view of continued improvements.
DIRIS Ap. Out 0/4 20 ma. Industrial Switching & Protection Systems
DIRIS Ap Out 0/4 20 ma Industrial Switching & Protection Systems 2 SOCOMEC - Réf. : 875 518 B-GB Contents PRELIMINARY OPERATIONS p. 4 GENERAL INFORMATION p. 4 INSTALLATION p. 4 PROGRAMMING p. 6 TECHNICAL
More informationCOUNTIS Ci Notice d utilisation GB Operating instructions Bedienungsanleitung NL Gebruiksaanwijzing
COUNTIS Ci I F Notice d utilisation GB Operating instructions D Bedienungsanleitung NL Gebruiksaanwijzing Istruzioni per l uso SP Instrucciones de servicio P Manual de instruções PRELIMINARY OPERATIONS
More informationCOUNTIS ECi2 ECi3. Operating instructions Multi-utility pulse concentrator F GB D I NL E P
COUNTIS ECi2 ECi3 Operating instructions Multi-utility pulse concentrator F GB D I NL E P GB Contents HAZARDS AND WARNING...3 INITIAL CHECKS...3 INTRODUCTION...4 JBUS/MODBUS COMMUNICATION...6 INSTALLATION...7
More informationCOUNTIS E05. Single-phase energy meter Direct - 40 A M-BUS. Instruction manual. en/countis-e0x
Instruction manual COUNTIS E05/E06 Single-phase energy meter Direct - 40 A M-BUS COUNTIS E05 COUNTIS E06 - MID www.socomec.com/ en/countis-e0x GB Contents 1. Documentation.... 3 2. Hazards and warnings...
More informationDIRIS N. Electrical network analysis system for quality control of your facilities
DIRIS N Electrical network analysis system for quality control of your facilities DIRIS D600 DIRIS A20 I V F P PF E Why do you need energy quality control? To verify that the network quality promised by
More informationMIC-2 Multi-instrument DATA SHEET
Measurements All 3-phase AC measurements True RMS 4-Quadrant energy Power Quality Analysis Replaces analogue meters RS-485 Modbus RTU protocol TCP/IP Modbus (optional) Profibus DP (optional) I/O modules
More informationMIC-2 MKII, Multi-instrument DATA SHEET
MIC-2 MKII, Multi-instrument DATA SHEET Measurements All 3-phase AC measurements True RMS 4-Quadrant energy Power Quality Analysis Replaces analogue meters RS-485 Modbus RTU protocol TCP/IP Modbus (optional)
More informationMIC-2 MKII & MIC-2 MKII DIN, Multi-instrument DATA SHEET
& DIN, Multi-instrument DATA SHEET Measurements All 3-phase AC measurements True RMS 4-Quadrant energy Power Quality Analysis Replaces analogue meters RS-485 Modbus RTU protocol TCP/IP Modbus (optional)
More informationDIRIS. The multi-function measurement UL range for managing your electrical networks
DIRIS A The multi-function measurement UL range for managing your electrical networks DIRIS D600 I V F P PF E A comprehensive range for measuring your energy efficiency The new DIRIS & COUNTIS solutions
More informationIso DIN. User Manual. 1 channel Earth Fault Monitoring
Page 1 of 5 2017 03 20 User Manual Iso DIN Iso DIN User Manual 1 channel Earth Fault Monitoring Megacon AB Ranhammarsvägen 20 S 168 67 Bromma Sweden Tel: 08 402 42 50 sales@megacon.se www.megacon.se eee
More informationEnergy Management Modular DC Energy analyzer Type VMU-E and VMU-X
Energy Management Modular DC Energy analyzer Type VMU-E and VMU-X Modular solution based on the combination of two units: VMU-E analysis unit and VMU-X universal power supply and RS485 communication unit.
More informationMID PRELIMINARY DATA SHEET. RI-D Series. Single Phase Multifunction Energy Meter (MID Certified) MID
PRELIMINARY DATA SHEET RI-D35-100 Series Single Phase Multifunction Energy Meter (MID Certified) MID direct connected Two pulse outputs LED pulse indication High definition LCD display with white backlight
More informationEnergy Management Modular DC Energy analyzer Type VIM-E and VIM-X
Energy Management Modular DC Energy analyzer Type VIM-E and VIM-X Modular solution based on the combination of two units: VIM-E analysis unit and VIM-X universal power supply and RS485 communication unit.
More informationTeSys protection components
Description, characteristics -pole electronic thermal overload, TeSys LR9D0, 0, 08, and LR9D0S DB8880.eps 7 / & 8 Description LR9D0, 0, 08 and self-powered electronic thermal overload are designed for
More informationSTATYS XS 16A / 32A CONFIGURATION MANUAL.
CONFIGURATION MANUAL STATYS XS 16A / 32A EN www.socomec.com CONTENTS 1. GENERAL CONFIGURATION.............................................. 3 2. MEASUREMENTS.......................................................
More informationDIRIS A. The multi-function measurement range MADE TO MEASURE
DIRIS A The multi-function measurement range for managing YOUR ELECTRICAL NETWORKS MADE TO MEASURE DIRIS D600 I V F P PF E A comprehensive range for measuring your energy efficiency The new DIRIS & COUNTIS
More informationATS Automatic transfer switches Advanced version
87045 LIMOGES Cedex Phone :+33 05 55 06 87 87 Fax :+33 05 55 06 88 88 ATS CONTENTS PAGES 1. USE 1 2. RANGE 1 3. DIMENSIONS 1 4. ELECTRICAL AND MECHANICAL CHARACTERISTICS 2 5. CONFORMITY 4 6. EQUIPMENTS
More informationRE22R1QMQ star-delta timing relay - 230VAC/440VAC - 1 C/O
Characteristics star-delta timing relay - 230VAC/440VAC - 1 C/O Main Range of product Product or component type Discrete output type Device short name Nominal output current Complementary Contacts type
More informationRE22R1QMQ star-delta timing relay - 230VAC/440VAC - 1 C/ O
Characteristics star-delta timing relay - 230VAC/440VAC - 1 C/ O Main Range of product Product or component type Discrete output type Device short name Nominal output current Zelio Time Modular timing
More informationLOGIC CONTROLLER INSTALLATION MANUAL NTR 756 B /E
LOGIC CONTROLLER INSTALLATION MANUAL NTR 756 B /E Table of contents 1. INTRODUCTION...1 2. HARDWARE DESCRIPTION...2 3. INSTALLATION...6 4. CONNECTION...8 5. USER SAFETY AND PROTECTION OF THE EQUIPMENT...11
More informationEnergy meters Single phase electrical energy meters WM1-6 / WM1M6
Energy meters Single phase electrical energy meters WM1-6 / WM1M6 o Single phase direct connected DIN-rail mounting meter o Class 1 for active energy according to EN 62053-21 and B according to EN 50470-3
More informationDIRIS A. The multi-function measurement range MADE TO MEASURE
DIRIS A The multi-function measurement range for managing YOUR ELECTRICAL NETWORKS MADE TO MEASURE DIRIS D600 I V F P PF E A comprehensive range for measuring your energy efficiency The new DIRIS & COUNTIS
More informationPowerLogic power-monitoring units. Power Meter PM500. Technical data sheet 2006
PowerLogic power-monitoring units Technical data sheet 2006 Functions and characteristics E90463 The PowerLogic PM500 Power Meter provides all measurement capabilities required to monitor an electrical
More informationDIRIS A & DIRIS B Power Metering and Monitoring Devices
DIRIS A & DIRIS B Power Metering and Monitoring Devices DIRIS A & DIRIS B A comprehensive range for single-point Metering Choose Application Mounting New installations Smart sensors match the pitch of
More informationRE17LAMW on-delay timing relay - 1 s..100 h V AC/DC - solid state output
Characteristics on-delay timing relay - 1 s..100 h - 24..240 V AC/DC - solid state output Complementary Control type Voltage range Main Range of product Product or component type Discrete output type Width
More informationRE8TA31BU industrial timing relay s - type A - 24 V AC/DC, V AC - 1 C/O
Characteristics industrial timing relay - 0.3..30 s - type A - 24 V AC/DC, 110..240 V AC - 1 C/O Main Range of product Product or component type Component name Time delay type Time delay range [Us] rated
More informationINSTALLATION & OPERATING MANUAL
INSTALLATION & OPERATING MANUAL IC 90 CHECK CONTENTS Package should contain.. Meter. Fixing Brackets (). Installation and Instruction Manual. The IC 90 meter is the latest kwh meter in the 900 series from
More informationDEIF A/S. TAS-331DG Selectable AC transducer G (UK) Installation and start up instructions. Watt or var transducer
Installation and start up instructions TAS-331DG Selectable AC transducer 4189300008G (UK) Watt or var transducer Supply and measuring voltage up to 690V DEIF A/S Configuration via PC-interface possible
More informationRE17LAMW on-delay timing relay - 1 s..100 h V AC/ DC - solid state output
Characteristics on-delay timing relay - 1 s..100 h - 24..240 V AC/ DC - solid state output Main Range of product Product or component type Discrete output type Width Component name Time delay type Time
More informationEC700. Pulses concentrator. User instructions
EC700 Pulses concentrator User instructions Contents Hazards and warning... 3 Initial checks... 3 Introduction... 4 Jbus/Modbus Communication... 5 Installation... 6 Configuration... 9 Use... 9 Programming...
More informationEngyVolt RV12 and RV15
Technical Information EngyVolt RV12 and RV15 Multifunctional electrical energy meters for top-hat rail installation or panel mounting Application For measuring voltage, frequency, current, power, as well
More informationINSTALLATION DKM-409 NETWORK ANALYSER WITH HARMONIC MEASUREMENT AND SCOPEMETER. Before installation:
DKM-409 NETWORK ANALYSER WITH HARMONIC MEASUREMENT AND SCOPEMETER The DKM-409 is a precision instrument designed for displaying various AC parameters in 3-phase distribution panels. Thanks to its isolated
More informationRM17UB3. Product data sheet Characteristics. voltage control relay RM17-U - range V AC. Main. Complementary
Characteristics voltage control relay RM17-U - range 183..528 V AC Main Range of product Product or component type Relay type Product specific application Relay name Relay monitored parameters Time delay
More informationE-STOP relays, safety gate monitors
Safety relay for monitoring E-STOP pushbuttons and safety gates. Approvals Unit features Positive-guided relay outputs: 5 safety contacts (N/O), instantaneous 1 auxiliary contact (N/C), instantaneous Connection
More informationRE8YG31BUTQ industrial timing relay s - type Qc - 24 V AC/DC, V AC - 1C/O
Characteristics industrial timing relay - 0.3..30 s - type Qc - 24 V AC/DC, 110..240 V AC - 1C/O Main Range of product Product or component type Component name Time delay type Time delay range Sep 23,
More informationVEO. V2UF230V10 Art.Nr.: TECHNICAL DATA
Continous voltage monitoring Mains fluctuation detection Detects voltage drop / short interruptions of at least 10ms Prevents undefined states in switching and control systems Generates reset pulse after
More informationDATA SHEET Selectable AC transducer, TAS-331DG
DATA SHEET Selectable AC transducer, TAS-331DG Measures power or reactive power on 3-phase AC networks Class 0.5 (IEC-688) measurement Supply and measuring voltage up to 690 V Easy configuration via PC
More informationLE ELECTRONICS Pvt. Ltd.
LE ELECTRONICS Pvt. Ltd. Monitoring Relays: LVM Line Voltage Monitors LCM - Line Current Monitors VMR Voltage Monitoring Relays CMR Current Monitoring Relays VCMR Voltage Current Monitoring Relays LFM
More informationOB735 Smart Energy Meter
User Manual Revision 3.002 English OB735 Smart Energy Meter Benefits and Main Features Three phase metering Standard DIN rail Format (DIN43880) CI.1 Accuracy (EN50470) Energy consumption LED Isolated pulse
More informationRE22R2AMR On-delay Timing Relay s 300h V AC/DC - 2C/O
Characteristics On-delay Timing Relay - 0.05s 300h - 24 240V AC/DC - 2C/O Main Range of product Product or component type Discrete output type Device short name Nominal output current Complementary Contacts
More informationPowerLogic power-monitoring units. EM1000 series power meter. Technical data sheet
PowerLogic power-monitoring units power meter Technical data sheet Distributed By: MetersUSA www.metersusa.com Meters@MetersUSA.com 1 224 365 5935 Basic energy meters Functions and characteristics PB105460
More informationSTBEHC3020KC counter kit STB - 1 CH Hz - 2 I
Characteristics counter kit STB - 1 CH - 0..40000 Hz - 2 I Main Range of product Product or component type Number of channels 1 Complementary Kit composition Counting input number 2 Counting frequency
More informationDIRIS B-10 & B-30. Multifunction meters and associated current sensors INSTRUCTION MANUAL. en/diris-b
INSTRUCTION MANUAL DIRIS B-10 & B-30 Multifunction meters and associated current sensors EN www.socomec.com/ en/diris-b GB CONTENTS 1. TABLE OF CONTENTS 1. DOCUMENTATION.......................................................
More informationPGR-4300 MANUAL GENERATOR GROUND-FAULT RELAY
Tel: +1-800-832-3873 E-mail: techline@littelfuse.com www.littelfuse.com PGR-4300 MANUAL GENERATOR GROUND-FAULT RELAY REVISION 3-B-041318 Copyright 2018 by Littelfuse, Inc. All rights reserved. Document
More informationDATA SHEET. Advanced Power Meter, APM 380 & APM 305
DATA SHEET Advanced Power Meter, APM 380 & APM 305 Easy installation Monitors all 3 phases 5 optional communication interfaces Phase error detection Low power consumption Two-pulse output DEIF A/S Frisenborgvej
More informationRM22TG. Product data sheet Characteristics. three-phase control relay Vac, 2 C/O. Main. Complementary. Network number of phases
Characteristics three-phase control relay 183 528Vac, 2 C/O Main Range of product Product or component type Relay type Network number of phases Relay name Relay monitored parameters Time delay type Switching
More informationProduct Manual for the Mini Industry Meter MIZ Installation I Device description I Operation
Product Manual for the Mini Industry Meter MIZ Installation I Device description I Operation Edition: 25.06.2009 MIZ-PHB-E-1.00 The contents of this manual are protected by copyright. It is forbidden to
More informationDigital Multifunction Meters. Digital Multifunction Meters
Digital Multifunction Meters Digital Multifunction Meters DIGITAL MULTIFUNCTIOL METERS SECTION INDEX 1. MFM 3410 3420 3430 3440 6100 & 2000 - Multifunctional Instrument Series 2. EM 3490, 3490SS, 3490DS
More information02/11/2015
DIN Rail Mount 35 mm HSV Part number 84874320 Control of overspeed, underspeed, operating rate, stopping Measurement via discrete sensors - 3-wire PNP or NPN, Namur, voltage 0-30V or volt-free contact
More informationDIRIS A. The multifunction multi-measurement station MADE TO MEASURE
DIRIS A The multifunction multi-measurement station for managing YOUR ELECTRICAL NETWORKS MADE TO MEASURE The DIRIS system: the benchmark Measurement is the key link in managing an energy efficiency project.
More informationict contactors EN 61095, IEC 1095 Interference
ict contactors DB23399 DB669 DB06604 Country approval pictograms EN 6095, IEC 095 ict contactors are available in two versions: b Contactors without manually-operated b Contactors with manually-operated.
More informationFor full product information, visit Use the SpeedSpec code or scan the QR Code for quick access to the specific web page.
R Safety Monitoring Relays For full product information, visit www.sti.com. Use the SpeedSpec code or scan the QR Code for quick access to the specific web page. Dual-Channel Safety Monitoring Relay Power
More informationRM35TF. Main. Product or component type. Product specific application. Relay monitored parameters 250 V AC 5 A AC
Characteristics multifunction phase control relay RM35-T - range 194..528 V AC Complementary Reset time Maximum switching voltage Minimum switching current Maximum switching current [Us] rated supply voltage
More informationData Sheet. Digital Multifunctional Power Meter with LCD Display and Optional Modules WPM D
WPM 770 Data Sheet 679.D.141.02 Digital Multifunctional Power Meter with LCD Display and Application The digital Weigel Power Meters WPM 770 have been designed to display the electrical parameters in low
More informationMultifuncion Measuring Device 96x96 mm, connection via CT
Viale Borri 231, 21100 Varese Italy Multifuncion Measuring Device Contents Pages 1. Description Use... 2 2. Range... 2 3. Overall dimensions... 2 4. Preparation Connection... 2 5. General characteristics...
More informationRM17TG. Main. Product or component type. Product specific application. Relay monitored parameters. Switching capacity in VA 250 V AC
Characteristics phase control relay RM17-T - range 183..484 V AC Complementary Maximum switching voltage Minimum switching current [Us] rated supply voltage Supply voltage limits Control circuit voltage
More informationRM35UB3. Product data sheet Characteristics. voltage control relay RM35-U - range V AC. Main. Complementary
Characteristics voltage control relay RM35-U - range 194..528 V AC Main Range of product Product or component type Relay type Product specific application Relay name Relay monitored parameters Time delay
More informationRE22R2QGMR Star-Delta Timing Relay s 300h V AC/DC - 2C/O
Characteristics Star-Delta Timing Relay - 0.05s 300h - 24 240V AC/DC - 2C/O Main Range of product Product or component type Discrete output type Device short name Nominal output current Complementary Contacts
More informationE 1. SPECOM - Network analyser. Content. E.2 Description. E.3 Specom C - Technical data. E.4 Specom M - Technical data. E.5 Data communication
SPCOM - Network analyser Content.2 Description.3 Specom C - Technical data.4 Specom M - Technical data.5 Data communication.5 Converter RS 485/232.5 Specom L - xploitation software The SPCOM network analyser
More informationSDM120 SERIES. SDM120 series User Manual. Single phase two wire DIN rail energy meter (One module)
SDM120 SERIES Single phase two wire DIN rail energy meter (One module) User manual ------------ 1.1 Safety instruction 1.2 Foreword 1.3 Performance criteria 1.4 Specifications 1.5 Basic errors 1.6 Dimension
More informationEM2020 Selectable AC transducer A (UK)
Installation and start up instructions EM2020 Selectable AC transducer 4189300016A (UK) Watt or var transducer Supply and measuring voltage up to 690V Configuration via PC-interface possible FAGET 35 mm
More informationRM35TF V AC
Characteristics multifunction phase control relay RM35-T - range 194..528 V AC Main Range of product Product or component type Relay type Product specific application Relay name Relay monitored parameters
More informationA2000 Multifunctional Power Meter
3-348-980-03 3/12.99 Capable of communications via Profibus-DP, LONWORKS interface or RS 485 interface (depending upon model) Measurement of current, voltage, active, reactive and apparent power, power
More informationRE17LCBM off-delay timing relay - control - 1 s..100 h V - solid state output
Characteristics off-delay timing relay - control - 1 s..100 h - 24..240 V - solid state output Main Range of product Product or component type Discrete output type Width Component name Time delay type
More informationE-STOP relays, safety gate monitors
Safety relay for monitoring E-STOP pushbuttons, safety gates and light barriers. Approvals Block diagram Unit features Positive-guided relay outputs: 6 safety contacts (N/O), instantaneous 4 auxiliary
More informationPGR-4700 MANUAL SENSITIVE GROUND-FAULT RELAY
Tel: +1-800-832-3873 E-mail: techline@littelfuse.com www.littelfuse.com/pgr-4700 PGR-4700 MANUAL SENSITIVE GROUND-FAULT RELAY REVISION 2-B-032218 Copyright 2018 by Littelfuse, Inc. All rights reserved.
More informationWEBVIEW Software solution for energy monitoring and analysis
WEBVIEW Software solution for energy monitoring and analysis Understand your energy system to ensure optimum and economical operation An efficient energy management system requires a perfect understanding
More informationUSER MANUAL 2012 V1.1
SMART MINI POWER SDM630 USER MANUAL 2012 V1.1-1 - Installation and Operation Instructions Important Safety Information is contained in the Maintenance section. Familiarise yourself with this information
More informationRE22R2CMR Off-delay Timing Relay s 300h V AC/DC - 2C/O
Characteristics Off-delay Timing Relay - 0.05s 300h - 24 240V AC/DC - 2C/O Main Range of product Product or component type Discrete output type Device short name Nominal output current Complementary Contacts
More informationRE7RB13MW adjustable off-delay timing relay s V AC DC - 2OC
Characteristics adjustable off-delay timing relay - 0.05..1 s - 240 V AC DC - 2OC Main Range of product Product or component type Contacts type and composition Component name Time delay type Time delay
More information100% electricity. Automatic transfer switch controllers ATL series
100% electricity Automatic transfer switch controllers ATL series Automatic transfer switch controllers Keep control around the clock General characteristics Rated auxiliary power supply: 220-230-240VAC
More informationDEIF A/S. MIC Multi-instrument G. Data sheet. Features. Accuracy. Measurements. Installation. Intelligent. Display. Communication DEIF A/S
Multi-instrument 4921210107G Features Measurements All 3-phase AC measurements True RMS Replaces analogue meters Intelligent Suitable for all 3-phase network topologies Replaces transducers Accuracy U,
More informationDATA SHEET Compact Genset Controller, CGC 200
DATA SHEET Compact Genset Controller, CGC 200 Auto start and parameter monitoring Warnings and shutdown protections Includes 5 digital inputs, 5 relay outputs Configurable for other applications Licence-free
More informationPulse concentrator, 12 inputs, 4 mod. DIN, with RS485 port
Viale Borri 231, 21100 Varese - Italy Pulse concentrator, 12 inputs, Contents Pages 1. Description - Use... 2 2. Range... 2 3. Overall dimensions... 2 4. Preparation - Connection... 2 5. General characteristics...
More informationRE8YG31BUTQ industrial timing relay s - type Qc - 24 V AC/DC, V AC - 1C/O
Characteristics industrial timing relay - 0.3..30 s - type Qc - 24 V AC/DC, 110..240 V AC - 1C/O Main Range of product Product or component type Component name Time delay type Time delay range [Us] rated
More informationMETERSUK. SmartLink D Y N A M i T E. 3 MOD CT Series. User Manual KEY FEATURES INDEX 3. TECHNICAL DESCRIPTION.
LTD METERSUK sales@meters.co.uk 01524 555 929 3 MOD CT Series Smart Energy Meter KEY FEATURES Three phase metering Three Phase metering, 7 din modules Accuracy class 1 according to IEC62053-21 LCD display,
More informationDIRIS Digiware Measurement and monitoring system for electrical installations
Multi-circuit metering & new diris-dw_006_a_cat diris-dw_005_a_cat diris-dw_004_a_cat The solution for > ndustry > Building > nfrastructure > Local authority Configuration with EasyConfig, see page 42.
More informationElectronic timer CT-SDD.22 Star-delta change-over with 2 n/o contacts
Data sheet Electronic timer CT-SDD. Star-delta change-over with n/o contacts The CT-SDD. is an electronic time relay with star-delta change-over. It is from the CT-D range. With their MDRC profile and
More informationRM4TR31 three-phase network control relay RM4-T - range V
Characteristics three-phase network control relay RM4-T - range 160..220 V Complementary [Us] rated supply voltage Control threshold undervoltage Control threshold overvoltage Output contacts Main Range
More informationRE Product data sheet Characteristics. universal plug-in timing relay - flashing s..60 mn V AC - 2 OC. Main.
Characteristics universal plug-in timing relay - flashing - 0.1 s..60 mn - 24..240 V AC - 2 OC Main Range of product Product or component type Discrete output type Contacts type and composition Width pitch
More informationIPD163C. Single-Phase Multifunction Meter User Manual Version: V1. August 20, 2017
163C Single-Phase Multifunction Meter User Manual Version: V1 August 20, 2017 This manual may not be reproduced in whole or in part by any means without the express written permission from IPD. The information
More informationPower Meter PowerMonitor 500
ROCKWELL AUTOMATION PROCUREMENT SPECIFICATION PROCUREMENT SPECIFICATION PowerMonitor 500 NOTICE: The specification guidelines in this document are intended to aid in the specification of products. Specific
More informationEMD-FL-C-10. Electronic monitoring relay for overcurrent and undercurrent monitoring of direct and alternating current in single-phase networks
Electronic monitoring relay for overcurrent and undercurrent monitoring of direct and alternating current in single-phase networks INTERFACE Data Sheet 102057_en_01 Description PHOENIX CONTACT - 02/2008
More informationSPM91 DIN Rail Single Phase Energy Meter Installation & Operation Manual V1.0
SPM91 DIN Rail Single Phase Energy Meter Installation & Operation Manual V1.0 ZHUHAI PILOT TECHNOLOGY CO., LTD. I Danger and warning! This device can be installed only by professionals. The manufacturer
More informationDatasheet - SRB 402EM-24V
Print - Create PDF - Create EXCEL file 20.04.2011-18:31:35h Datasheet - SRB 402EM-24V Output expanders / SRB 402EM Expander module for contact expansion 4 safety contacts, STOP 0 2 Signalling outputs (Minor
More informationE-STOP relays, safety gate monitors
Safety relay for monitoring E-STOP pushbuttons, safety gates and light barriers. Approvals Unit features Positive-guided relay outputs: 7 safety contacts (N/O), instantaneous 2 auxiliary contacts (N/C),
More informationPositive-guided relay outputs: 3 safety contacts (N/O), instantaneous. 1 auxiliary contact (N/C), instantaneous
Safety relay for monitoring E-STOP pushbuttons. Approvals Unit features Positive-guided relay outputs: 3 safety contacts (N/O), instantaneous 1 auxiliary contact (N/C), instantaneous Safe separation of
More informationEnergy Management Energy Transducer Type ET112
Energy Management Energy Transducer Type Single phase energy transducer Class 1 (kwh according to EN62053-21 Class B (kwh according to EN50470-3 Accuracy ±0.5% RDG (current/voltage Direct current measurement
More informationRM17TG. Main. Product or component type. Product specific application. Relay monitored parameters. Switching capacity in VA
Characteristics phase control relay RM17-T - range 183..484 V AC Main Range of product Product or component type Relay type Product specific application Relay name Relay monitored parameters Switching
More informationABL8BBU24400 battery control module V DC - 24 V - 40 A - for regulated SMPS
Characteristics battery control module - 24..28.8 V DC - 24 V - 40 A - for regulated SMPS Main Range of product Product or component type Input voltage Output voltage Maximum output current Complementary
More informationElectronic timer CT-EBD.12 Flasher starting with ON with 1 c/o (SPDT) contact
Data sheet Electronic timer CT-EBD.12 Flasher starting with ON with 1 c/o (SPDT) contact The CT-EBD.12 is an electronic time relay with the function flasher starting with ON. It is from the CT-D range.
More information02/11/2015
24 x 48 Hour CTR24 non-backlit model Part number 87622162 Display : 8-digit LCD, height 8 mm Built-in module for voltage inputs 10 260 VAC/DC () 4 timing ranges : 99,999.99 hrs - 99,999.59 hrs - 999,999.9
More informationRE22R2KMR Off-delay Timing Relay s 10min V AC/DC - 2C/O
Characteristics Off-delay Timing Relay - 0.05s 10min - 24 240V AC/DC - 2C/O Main Range of product Product or component type Discrete output type Device short name Nominal output current Complementary Contacts
More informationDKM-405 NETWORK ANALYSER WITH TOTAL HARMONIC DISTORTION DISPLAY
datakom@datakom.com.tr http://www.datakom.com.tr Tel: +9-216 466 84 6 Fax: +9-216 364 65 65 DKM-45 NETWORK ANALYSER WITH TOTAL HARMONIC DISTORTION DISPLAY INTRODUCTION The DKM-45 is a low cost precision
More informationEnergy Management Modular Energy meters Type EM2-96
Energy Management Modular Energy meters Type EM2-96 Product Description µp-based modular energy meter with a built-in configuration key-pad. The energies are both partial and total counted. The housing
More informationDATA SHEET. Advanced Energy Meter, AEM 380 & AEM 305
DATA SHEET Advanced Energy Meter, AEM 380 & AEM 305 Easy installation MID-approved 5 optional communication interfaces Phase error detection Low power consumption Two tariffs Two-pulse output DEIF A/S
More informationRE22R2QTMR Star-Delta Timing Relay s 300h V AC/DC - 2C/O
Characteristics StarDelta Timing Relay 0.05s 300h 24 240V AC/DC 2C/O Main Range of product Product or component type Discrete output type Device short name Nominal output current Zelio Time Modular timing
More informationTeSys IEC Contactors and Overload Relays
TeSys IEC Contactors and Overload Relays Making High-Fault Short-Circuit Current Ratings Simple Schneider Electric is an industry leader in IEC contactors and overload relays, and is recognized as the
More informationPHOENIX CONTACT Features
Electronic monitoring relay for temperature monitoring Data sheet 107385_en_00 1 Description PHOENIX CONTACT - 2016-05-10 Features Safety and system availability requirements are constantly on the increase
More informationEnergy Management BUS Adapter Type VMU-B 01
Energy Management BUS Adapter Type VMU-B 01 RS485 (Modbus) to M-Bus communication adapter EM21-72D, EM24-DIN and EM33-DIN self recognition Front diagnostic LED s Universal 18 to 260 VAC/DC power supply
More information