SIMATIC MV320 / SIMATIC MV325. SIMATIC Ident. Handheld reading systems SIMATIC MV320 / SIMATIC MV325. Preface. Safety notes.

Transcription

1 Preface Safety notes 1 SIMATIC Ident Handheld reading systems Operating Instructions Description 2 Installing and connecting (SIMATIC MV325) 3 Connecting (SIMATIC MV320) 4 Commissioning 5 Operation 6 Alarm, error and system messages 7 Service and maintenance 8 Technical data 9 Dimension drawings 10 Ordering data 11 A Appendix 08/2015 C79000-G8976-C352-03

2 Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION indicates that minor personal injury can result if proper precautions are not taken. NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: Trademarks WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed. All names identified by are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Division Process Industries and Drives Postfach NÜRNBERG GERMANY C79000-G8976-C P 09/2015 Subject to change Copyright Siemens AG All rights reserved

3 Preface Validity of these operating instructions This document contains information on the products listed below. Valid for devices with the following article numbers Article number 6GF3320-0HT01 6GF3325-0HT01 Device SIMATIC MV320 SIMATIC MV325 The SIMATIC MV320 and SIMATIC MV325 readers are sophisticated, powerful, and versatile handheld barcode readers. Typical areas of application: Health care, pharmacy, retail trade and manufacturing. SIMATIC MV320 SIMATIC MV325 Product designation In the remainder of this document, the term "device" or "reader" or "handheld reader" is also used instead of the full product name "SIMATIC MV320" or "SIMATIC MV325". Operating Instructions, 08/2015, C79000-G8976-C

4 Preface Purpose of the operating instructions Note The operating instructions contain all the important information about the device Read the operating instructions before starting to work with this device. Noting and acting on this information: Ensures the device functions correctly Saves you service costs These operating instructions contain all the information you need for commissioning and using the device. It is intended both for persons who connect up the device electrically and commission and operate it as well as for service technicians and maintenance technicians. New in this release Revision of contents and editing Code configuration section updated and removed from manual. Replaced operating instructions These operating instructions replace the operating instructions edition 03/2014. Current operating instructions on the Internet You will also find the latest version of these operating instructions on the Internet pages of Siemens Industry Online Support under the following entry ID: ( Additional documentation A current list of the code configurations mentioned in this manual is available in the manuals: SIMATIC MV320 Configuration guide ( SIMATIC MV325 Configuration guide ( Environmental protection Devices described in this programming manual can be recycled owing to the low content of noxious substances in their version. Please contact a certified waste disposal company for eco-friendly recycling and to dispose of your old devices. 4 Operating Instructions, 08/2015, C79000-G8976-C352-03

5 Preface History Previous editions of these operating instructions: Edition Remark 12/2013 First edition 08/2015 Revision of contents and editing Code configuration section updated and removed from manual. Security information Siemens provides products and solutions with industrial security functions that support the secure operation of plants, solutions, machines, equipment and/or networks. They are important components in a holistic industrial security concept. With this in mind, Siemens products and solutions undergo continuous development. Siemens recommends strongly that you regularly check for product updates. For the secure operation of Siemens products and solutions, it is necessary to take suitable preventive action (e.g. cell protection concept) and integrate each component into a holistic, state-of-the-art industrial security concept. Third-party products that may be in use should also be considered. For more information about industrial security, visit To stay informed about product updates as they occur, sign up for a product-specific newsletter. For more information, visit Operating Instructions, 08/2015, C79000-G8976-C

6 Preface 6 Operating Instructions, 08/2015, C79000-G8976-C352-03

7 Table of contents Preface Safety notes Description Product package SIMATIC MV SIMATIC MV Installing and connecting (SIMATIC MV325) Mounting the charging station Mounting the charging station with base plate and rubber feet Charging station with base plate secured to a working surface Connecting (SIMATIC MV320) Connecting and removing cables Connector assignment USB and RS-232 cable Connector assignment reader Commissioning Inserting and removing the battery (SIMATIC MV325) Charging the reader (SIMATIC MV325) Turn the reader on Establishing a Bluetooth connection (SIMATIC MV325) Operation Working with the SIMATIC MV320 reader Aligning the SIMATIC MV325 reader Setting the communication mode (SIMATIC MV325) Communication in batch mode (SIMATIC MV325) Codes with enabled factory setting Codes with disabled factory setting Enabling "Suffix - Enter" Alarm, error and system messages Feedback from the reader Charge status displays of the battery (SIMATIC MV325) Batch mode display (SIMATIC MV325) Operating Instructions, 08/2015, C79000-G8976-C

8 Table of contents 8 Service and maintenance Technical data Dimension drawings Ordering data A Appendix A.1 Code configurations A.2 "Specify character length to be read" function A.3 Service and Support A.4 Certificates and approvals A.4.1 FCC information A.4.2 IC-FCB information Index Operating Instructions, 08/2015, C79000-G8976-C352-03

9 Safety notes 1 Alterations to the device CAUTION Alterations to the devices are not permitted. Failure to observe this requirement shall constitute a revocation of the radio equipment approval, CE approval and warranty. Therefore do not make any alterations to the device. Repairs WARNING Personal injury or equipment damage due to unauthorized opening or repairing Unauthorized opening or repairing of the device can lead to personal injury or equipment damage. Therefore do not carry out repairs yourself. Repairs may only be carried out by authorized qualified personnel at the manufacturer's site. See section Service and maintenance (Page 43). Proper disposal and recycling The HMI devices described in these Operating Instructions can be recycled due to the low levels of pollutants. Contact a certified disposal service company for environmentally sound recycling and disposal of your old devices. When disposing of batteries, observe the locally applicable legal regulations. Operating Instructions, 08/2015, C79000-G8976-C

10 Safety notes Adherence to FCC requirements NOTICE Adherence to FCC requirements for RF radiation To adhere to the FCC requirements relating to the effects of RF radiation, this device must not be operated beside or in conjunction with other antennas or transmitting devices. NOTICE Changes or modifications to the device Changes or modifications not expressly approved by the person responsible for adherence to the relevant regulations could result in the loss of the user's operating approval for the device. 10 Operating Instructions, 08/2015, C79000-G8976-C352-03

11 Description Product package SIMATIC MV320 The SIMATIC MV320 reader (article number 6GF3320-0HT01) is supplied with the following components: SIMATIC MV320 handheld reader The reader can be used on the USB or RS-232 interface. To use the RS-232 interface, you need to order the RS-232 cable and, if necessary, the appropriate power supply as accessories. SIMATIC MV325 The SIMATIC MV325 reader (article number 6GF3325-0HT01) is supplied with the following components: SIMATIC MV325 handheld reader with battery, charging station and USB cable (0.9 m) The charging station has a USB interface and a Bluetooth wireless interface. Operating Instructions, 08/2015, C79000-G8976-C

12 Description 2.2 SIMATIC MV SIMATIC MV320 Characteristics and areas of application Due to the following features, the reader is also suitable for demanding applications. Due to the optical dual-field platform, the SIMATIC MV320 can read wide and extremely small barcodes. Thanks to intuitive targeting, 1D and 2D barcodes as well as barcodes belonging to postal services can be read reliably and at little expense. Thanks to glare control, barcodes can be read from bottles, packed foodstuffs and cans without any problem. Whether in health care, retail trade or in other areas of application with intensive use - the plastic housing, which is resistant to disinfectants and has degree of protection IP54, protects the performance and the working lifetime of the reader from aggressive cleaning agents, dust, penetration of water and even being dropped. Are you on the move, working in different environments or do you need to read codes accurately on a large number of items? If so, the SIMATIC MV320 will be a valuable addition to your equipment. Areas of application Health care Mobile voucher or ticket reader (events, air tickets, cinema etc.) Pharmacy Retail trade and manufacturing Reading strongly reflecting barcodes Overview of the functions and benefits Available on a stand or as a handheld device. Manual or automatic triggering Feedback on correct read function with programmable LED display, acoustic signal and vibration. Optional metal stand Efficient current consumption 12 Operating Instructions, 08/2015, C79000-G8976-C352-03

13 Description 2.3 SIMATIC MV SIMATIC MV325 Characteristics and areas of application Due to the following features, the reader is also suitable for demanding applications. The super fast and extremely durable device works with a high-performance scan engine for recognition of all 1D and 2D barcodes, as well as barcodes of individual postal services. With its patented dual-field optics, both wide and very small barcodes can be read. With the patented glare control technology, codes on shining surfaces can be reliably detected. The long-life batteries of the device with their fast triggering mechanism measure the battery charge level precisely and show the remaining lifetime of the battery in a 4 LED level display at the press of a button. The charging station is available with an integrated Bluetooth modem. The housing, which is resistant to disinfectants and has degree of protection IP65, prevents damage to plastic parts and protects the electronics and optics. Areas of application Health care Manufacturing Retail trade Warehouse management Reading strongly reflecting barcodes Overview of the functions and benefits Light design: The reader weighs only 171 g. Long-life batteries with fast trigger mechanism. Charge status LED with charge display. Read confirmation by vibration, acoustic and LED signal. Fast, direction-independent reading of 1D and 2D barcodes and barcodes of postal services. Compatible with Bluetooth-supported Android, ios and Windows mobile devices and tablets. The housing, which is resistant to disinfectants and has IP65, prevents damage to plastic parts and protects the electronics and optics. Paging button supports the localization of the mobile reader. Reads barcodes on mobile devices. Operating Instructions, 08/2015, C79000-G8976-C

14 Description 2.3 SIMATIC MV Operating Instructions, 08/2015, C79000-G8976-C352-03

15 Installing and connecting (SIMATIC MV325) Mounting the charging station You can mount the charging station according to your requirements: Charging station without base plate (Page 15) Charging station with base plate (Page 16) Secure charging station with base plate to a working surface (Page 19) 1. Insert the USB cable or power cable with the cylindrical side into the charging station. Figure 3-1 Inserting the USB cable/power cable into the charging station 2. To prevent the station from slipping: Secure the rubber feet to the corners 1 on the underside of the charging station. Figure 3-2 Charging station: Securing the rubber feet Operating Instructions, 08/2015, C79000-G8976-C

16 Installing and connecting (SIMATIC MV325) 3.2 Mounting the charging station with base plate and rubber feet The charging station is ready for use. 3.2 Mounting the charging station with base plate and rubber feet 1. Insert the USB cable or power cable with the cylindrical side into the charging station. Figure 3-3 Inserting the USB cable/power cable into the charging station For mounting the weighted base plate: 2. Lay the side of the base plate marked with "THIS SIDE DOWN" on the supporting surface. 3. Place the charging station on the base plate. 16 Operating Instructions, 08/2015, C79000-G8976-C352-03

17 Installing and connecting (SIMATIC MV325) 3.2 Mounting the charging station with base plate and rubber feet 4. Secure the charging station with the supplied screws 2 in the threaded holes 1 of the base plate. Figure 3-4 Base plate: Threaded holes Figure 3-5 Charging station: Tightening the screws You have secured the charging station to the base plate. Operating Instructions, 08/2015, C79000-G8976-C

18 Installing and connecting (SIMATIC MV325) 3.2 Mounting the charging station with base plate and rubber feet 5. To prevent the charging station from slipping: Secure the rubber feet to the round markers 3 on the underside of the base plate. Figure 3-6 Base plate: Rubber feet markers 3 Figure 3-7 Base plate: Rubber feet 4 secured The charging station is ready for use. 18 Operating Instructions, 08/2015, C79000-G8976-C352-03

19 Installing and connecting (SIMATIC MV325) 3.3 Charging station with base plate secured to a working surface 3.3 Charging station with base plate secured to a working surface 1. Insert the USB cable or power cable with the cylindrical side into the charging station. Figure 3-8 Inserting the USB cable/power cable into the charging station To mount the charging station on a working surface: 2. Lay the side of the base plate marked with "THIS SIDE DOWN" on the supporting surface. 3. Secure the base plate to the working surface with screws through the pre-drilled mounting holes 1. Note Mounting screws are not supplied with the product Since the mounting surfaces can differ, the mounting screws are not supplied with the product. Figure 3-9 Base plate: Mounting holes Operating Instructions, 08/2015, C79000-G8976-C

20 Installing and connecting (SIMATIC MV325) 3.3 Charging station with base plate secured to a working surface 4. Place the charging station on the secured base plate. 5. Secure the charging station with the supplied screws 2 in the threaded holes 1 of the base plate. Figure 3-10 Base plate: Threaded holes Figure 3-11 Charging station: Tightening the screws You have secured the charging station with the base plate on the working surface. The charging station is ready for use. 20 Operating Instructions, 08/2015, C79000-G8976-C352-03

21 Connecting (SIMATIC MV320) 4 NOTICE Avoid exceeding the maximum voltage If the maximum voltage is exceeded, this voids the manufacturer's guarantee. Maximum voltage tolerance: 5 V ± 10 % The components must comply with the requirements of the EC directive RoHS and the REACH Regulation: See EC directive 2011/65/EU (RoHS 2) and the Regulation (EC) No. 1907/2006 (REACH Regulation). 4.1 Connecting and removing cables Connecting the cable Plug the RJ-50 end of the cable into the bottom of the device handle. Press the connector firmly into the device until it audibly locks in place. The cable is then correctly connected. Operating Instructions, 08/2015, C79000-G8976-C

22 Connecting (SIMATIC MV320) 4.2 Connector assignment USB and RS-232 cable Removing the cable 1. Insert a paper clip into the opening on the side of the device handle. 2. Remove the cable carefully from the device. 4.2 Connector assignment USB and RS-232 cable USB cable Example with connector assignments: Table 4-1 Connector table Connector A Designation Wire Color Connector B 1 VIN 24 AWG Red 1 2 DM 28 AWG White 2 3 DP 28 AWG Green 3 4 GND 24 AWG Black 10 Housing - Shield Blank Housing Description of the connector assignment of the reader (Page 24). 22 Operating Instructions, 08/2015, C79000-G8976-C352-03

23 Connecting (SIMATIC MV320) 4.2 Connector assignment USB and RS-232 cable RS -232 cable Example with connector assignments: Figure 4-1 RS-232 cable with pin assignment Table 4-2 Connector table Connector A Designation Wire Color Connector B 1 VIN 24 AWG 4 TX 28 AWG 5 RTS 28 AWG 6 RX 28 AWG 7 CTS 28 AWG 10 GND 24 AWG Wire Color Connector C Red 9 24 AWG Red PIN Brown 2 Orange 8 Yellow 3 Green 7 Housing - Shield Shield Black 5 24 AWG Black RING Description of the connector assignment of the reader (Page 24). Operating Instructions, 08/2015, C79000-G8976-C

24 Connecting (SIMATIC MV320) 4.3 Connector assignment reader 4.3 Connector assignment reader The SIMATIC MV320 has an RJ-50 connector (10P-10C). The connector assignment is as follows: Connector Name/function 1 +VIN (5v) 2 USB_DM 3 USB_DP 4 RS-232 TX (output from the reader) 5 RS-232 RTS (output from the reader) 6 RS-232 RX (input to the reader) 7 RS-232 CTS (input to the reader) 8 External triggering (active-low input to the reader) 9 Free 10 GND 24 Operating Instructions, 08/2015, C79000-G8976-C352-03

25 Commissioning Inserting and removing the battery (SIMATIC MV325) Insert the battery in the device as shown in the figure on the left. If the battery is inserted correctly, it locks in place. To remove the battery, push the slider (figure on the right) to unlock the battery. 1 Slider Inserting the battery (figure on the left): If the battery is inserted correctly, it locks in place. Removing the battery (figure on the right): Push the slider (in the direction of the arrow) and remove the battery. 5.2 Charging the reader (SIMATIC MV325) Charge the batteries before turning on the device for the first time In the delivery state, the batteries are approximately 50% charged. Charge the batteries before turning on the device for the first time. The charging time for a completely discharged battery with the charging station and the USB cable is about 4 hours. Operating Instructions, 08/2015, C79000-G8976-C

26 Commissioning 5.2 Charging the reader (SIMATIC MV325) Charging the reader 1. Connect the USB cable to the USB port of the computer. 2. Remove the cover labeled "Remove Before Use". 3. Place the device in the charging station Charge indicator Charging station 26 Operating Instructions, 08/2015, C79000-G8976-C352-03

27 Commissioning 5.3 Turn the reader on 5.3 Turn the reader on SIMATIC MV320 With USB cable 1. Plug the USB end of the cable into a USB connector on the host device. After a few seconds, you will hear two beeps. 2. The LED goes off, indicating that the reader is ready for operation. With RS-232 cable 1. Connect the power supply unit to an alternating current power supply. 2. Insert the power cable in the corresponding connector of the RS-232 cable. 3. Connect the RS-232 plug to the suitable serial connector of the host device. After a few seconds, the reader generates two beeps and vibrates. 4. The LED goes off, indicating that the reader is ready for operation. SIMATIC MV325 To turn on the device, press one of the buttons 1 or the trigger 2 and hold it down for 1 s. The reader beeps, vibrates and the LEDs flash when the device is turned on and ready for operation. Operating Instructions, 08/2015, C79000-G8976-C

28 Commissioning 5.4 Establishing a Bluetooth connection (SIMATIC MV325) 5.4 Establishing a Bluetooth connection (SIMATIC MV325) Note Using the SIMATIC MV325 in an area where there is WLAN communication If you use the SIMATIC MV325 in an area where there is WLAN communication, this may result in interference. We therefore recommend that you select the 5 GHz frequency range for the WLAN communication and take this into account in the radio field planning. Establishing the connection To establish a Bluetooth connection from the charging station with the integrated Bluetooth modem: 1. Slide the switch for the communication mode 1 on the bottom of the charging station to the right in the direction of the arrow. 2. Scan in the QuickConnect code 3. The QuickConnect code is on the front of the charging/bluetooth modem station or on the external Bluetooth modem. While the connection is being established, the symbol for a wireless connection 4 at the top of the reader flashes. The blue LED 2 on the charging station or on the Bluetooth modem also flashes while the connection is being established. As soon as the connection has been established successfully, the blue LED 2 is lit permanently. The reader beeps once and the wireless symbol 4 is lit constantly Communication mode switch Blue LED QuickConnect code Wireless symbol Read confirmation Memory symbol 28 Operating Instructions, 08/2015, C79000-G8976-C352-03

29 Operation Working with the SIMATIC MV320 reader Without metal stand 1. Hold down the trigger button of the reader. 2. The two blue beams sent out by the reader are used for targeting. The blue beams must be directed to the center of the barcode. The ideal read distance between the device and barcode is approximately 10 cm. As soon as the reader is at the optimum read distance, the barcode is read. To confirm that the barcode was read correctly, the reader generates a beep, vibrates and a green LED flashes. Note Changing factory settings To change factory settings, scan in the appropriate code: See section Code configurations (Page 53). Operating Instructions, 08/2015, C79000-G8976-C

30 Operation 6.1 Working with the SIMATIC MV320 reader With metal stand/with stand detection The hardware product version 2 of the reader has stand detection. By default, the reader automatically changes to the motion detection mode when it is placed on the stand. In this mode, the reader is activated by holding a barcode in the scanner field. To confirm that the barcode was read correctly, the reader generates a beep, vibrates and a green LED flashes. When the reader is taken off the stand, it changes to manual mode: To read a barcode, you need to press the trigger button (see "Without metal stand"). With metal stand / without stand detection The hardware product version 1 of the reader does not have automatic stand detection with which barcode reading on detection of motion is activated when the reader is placed on the stand. To configure this hardware product version for scanning on detection of motion, scan in the appropriate code: See section Code configurations (Page 53). 30 Operating Instructions, 08/2015, C79000-G8976-C352-03

31 Operation 6.2 Aligning the SIMATIC MV325 reader 6.2 Aligning the SIMATIC MV325 reader 1. Press a button or the trigger button of the reader. 2. Hold down the button or trigger button. The two blue beams sent out by the reader are used for targeting. 3. The blue beams must be directed to the center of the barcode. If the barcode is in the viewing field of the device and at the optimum read distance (approximately 10 cm from the device), the barcode will be read automatically. The reader beeps and vibrates and the read confirmation LED flashes green. Operating Instructions, 08/2015, C79000-G8976-C

32 Operation 6.3 Setting the communication mode (SIMATIC MV325) 6.3 Setting the communication mode (SIMATIC MV325) Charging stations with an integrated Bluetooth modem are equipped with a switch for the communication mode 3. With this switch, the reader can transfer data either via the Bluetooth modem or via a cable connection. The switch is located on the bottom of the charging station Data is transmitted over Bluetooth (direction of the arrow) Data is transmitted over USB port Switch for the communication mode Wireless communication via Bluetooth If you move the switch for the communication mode 3 to the position 1 (direction of the arrow), the reader communicates via the Bluetooth modem. To establish a Bluetooth link, you need to scan the "QuickConnect" code on the front of the charging station. The scanned data is then transferred wirelessly to the host device. Wired communication via USB port To transfer scanned data in cable mode, you need to place the reader in the charging station so that data can be transferred to the host device. If a cable connection is required, move the switch for the communication mode 3 to the position 2. For USB download mode or USB keyboard mode, you need to scan in the activation code of the batch mode. 32 Operating Instructions, 08/2015, C79000-G8976-C352-03

33 Operation 6.4 Communication in batch mode (SIMATIC MV325) 6.4 Communication in batch mode (SIMATIC MV325) In batch mode, you can collect data with the reader and buffer it in the reader. Depending on the selected batch mode, the data is not transferred to the host device until you put the reader back in the charging station or scan the configuration code for data transmission. You can distinguish between the following communication modes for communication in batch mode: Via Bluetooth Via USB port Depending on the required communication mode, you must move the switch on the bottom of the charging station 3 to the corresponding position. 1 2 Data is transmitted over Bluetooth (direction of the arrow) Data is transmitted over USB port Transmission of saved data via Bluetooth Use the following procedure to enable data transmission in batch mode via Bluetooth: 1. Move the switch 3 for the communication mode on the bottom of charging station to the position 1 (direction of the arrow). 2. Scan the configuration barcode of the batch mode: Batch Mode Enable - Log Only 1) 3. Scan the "QuickConnect" code on the front of the associated charging station or the associated Bluetooth modem. Once you have enabled the communication mode, you can start collecting data. To transfer the data to the host device, you must scan the configuration code "Batch Mode Transfer All Data in Memory". Operating Instructions, 08/2015, C79000-G8976-C

34 Operation 6.4 Communication in batch mode (SIMATIC MV325) Transmission of the saved data via USB port Use the following procedure to enable data transmission in batch mode via USB: 1. Move the switch 3 for the communication mode on the bottom of charging station to the position Scan the configuration code of the USB communication mode: USB Keyboard Mode - Batch Mode Only 1) 3. Scan the configuration barcode of the batch mode: Batch Mode Enable - Send and Log 1) 4. Scan the configuration barcode for automatic data transfer: Batch Mode Auto Transfer Buffer memory On Once you have enabled the communication mode, you can start collecting data. To transfer the data to the host device, you must place the reader in the charging station. The reader will start transmission of the data after 5 seconds. The delay allows the host device to prepare itself to receive the data. 1) A list of all configuration codes, e.g. for batch mode or communication mode, is available in the manual "SIMATIC MV325 Configuration Guide ( 34 Operating Instructions, 08/2015, C79000-G8976-C352-03

35 Operation 6.5 Codes with enabled factory setting 6.5 Codes with enabled factory setting To enable or disable the codes, scan in the relevant codes (see section Code configurations (Page 53)). If a reader needs to be configured for reading codes that are not included in the list: Scan in the relevant codes in to enable them (see section Code configurations (Page 53)). SIMATIC MV320 The following codes are enabled in the factory settings: Codabar Code 39 Code 93 Code 128 Data matrix Data Matrix Rectangle All GS1 DataBar Interleaved 2 of 5 MSI Plessey PDF417 QR code UPC/EAN/JAN SIMATIC MV325 The following codes are enabled in the factory settings: Aztec Codabar Code 39 Code 93 Code 128 Data matrix Data Matrix Rectangle All GS1 DataBar Interleaved 2 of 5 PDF417 Operating Instructions, 08/2015, C79000-G8976-C

36 Operation 6.6 Codes with disabled factory setting QR code UPC/EAN/UPC-E 6.6 Codes with disabled factory setting To enable or disable these codes: Scan in the relevant codes (see section Code configurations (Page 53)). SIMATIC MV320 The following codes are disabled in the factory settings: Codablock F Code 11 Code 32 Composite Han Xin Code Hong Kong 2 of 5 IATA 2 of 5 Matrixcode Matrix 2 of 5 Micro PDF417 MSI Plessey NEC 2 of 5 Pharmacode Postal Codes Plessey Standard 2 of 5 Telepen Trioptic 36 Operating Instructions, 08/2015, C79000-G8976-C352-03

37 Operation 6.6 Codes with disabled factory setting SIMATIC MV325 The following codes are disabled in the factory settings: Codablock F Code 11 Code 32 Composite Data Matrix Inverse Han Xin Code Hong Kong 2 of 5 IATA 2 of 5 Matrixcode Matrix 2 of 5 Micro PDF417 MSI Plessey NEC 2 of 5 Pharmacode Plessey Postal Codes Straight 2 of 5 Telepen Trioptic Operating Instructions, 08/2015, C79000-G8976-C

38 Operation 6.7 Enabling "Suffix - Enter" 6.7 Enabling "Suffix - Enter" In the factory settings of the readers, "Suffix - Enter" is disabled. To enable "Suffix - Enter", scan in the required configuration code: SIMATIC MV320: Suffix Enter (USB Keyboard Mode Only) Suffix Carriage Return Line Feed (RS232 Mode Only) SIMATIC MV325: Suffix Enter (USB Keyboard Mode Only) A list of the mentioned codes is available in the manuals "SIMATIC MV320 Configuration guide ( and "SIMATIC MV325 Configuration guide ( 38 Operating Instructions, 08/2015, C79000-G8976-C352-03

39 Alarm, error and system messages Feedback from the reader Table 7-1 SIMATIC MV320 Situation LED displays on the reader Acoustic signal SIMATIC MV320 is turned on. Green LED flashes 1x Successful establishment of the connection between SIMATIC MV320 and the host (by cable). Green LED goes off after connection establishment 1x Decoding attempt active. Green LED is off Decoding and data transfer successful. Green LED flashes 1x Configuration code successfully Green LED flashes 2x decoded and processed. Configuration code successfully decoded but not successfully processed. Green LED flashes 4x Vibration signal Table 7-2 SIMATIC MV325 Situation SIMATIC MV325 turned on successfully. SIMATIC MV325 connected to host successfully. SIMATIC MV325 not connected to host successfully. LED displays on the reader All LEDs flash Acoustic signal 1x Wireless symbol 1x flashes -- 3x -- Decoding and data transfer successful. Read display flashes 1x Decoding and data transfer not -- 3x -- successful. Configuration code successfully Read display flashes 2x decoded and processed. Configuration code not successfully decoded and processed. -- 4x -- Batch mode enabled and no data Batch symbol off stored Batch mode enabled and data stored. Batch symbol flashing Vibration signal Operating Instructions, 08/2015, C79000-G8976-C

40 Alarm, error and system messages 7.2 Charge status displays of the battery (SIMATIC MV325) Situation Memory for batch process full. Batch mode enabled, data stored and SIMATIC MV325 in sleep mode. LED displays on the reader Batch symbol flashes 5x per second Batch symbol flashes 10x per second Acoustic signal Vibration signal Charge status displays of the battery (SIMATIC MV325) Checking the charge status 1 2 Charge status button Charge status displays To find out how much battery charge remains, press the button for the charge status 1. If the battery charge is less than 10%, the 1st LED flashes at short intervals. If there is 25% or more charge remaining, the LEDs flash "ON" for 4 seconds. 40 Operating Instructions, 08/2015, C79000-G8976-C352-03

41 Alarm, error and system messages 7.3 Batch mode display (SIMATIC MV325) Charge status display during charging If there is less than 10% battery charge remaining, the 1st LED flashes at short intervals during charging. If the battery charge is 25% or more, the LEDs flash "ON" for 4 s and "OFF" for 1 s. Battery charge status < 10% Charge status display Flashing quickly < 25% % % > 75% 7.3 Batch mode display (SIMATIC MV325) In batch mode, the memory symbol of the SIMATIC MV325 flashes at 10 second intervals indicating that data was stored. If the memory is full, the memory symbol flashes 5 times per second. To release memory space, you need to download or delete data. If no data is stored, the memory symbol does not flash. You will find an explanation of how to switch the SIMATIC MV325 to batch mode in Communication in batch mode (SIMATIC MV325) (Page 33) Wireless symbol Read confirmation Memory symbol Operating Instructions, 08/2015, C79000-G8976-C

42

43 Service and maintenance 8 The reader requires little maintenance. Below, you will find several useful tips on upkeep and maintenance. To ensure optimum performance of the reader, the window of the reader must be clean. The window is the colorless plastic part in the head of the reader. The reader works with CMOS technology in much the same way as a digital camera. A dirty window could have the result that the reader is no longer capable of reading barcodes. If the window is dirty, clean it with a soft, non-abrasive cloth or a cosmetic wipe (without lotion and not impregnated) and a little water. You can also use a mild cleansing agent: Then wipe the window with a damp cloth. Approved cleaning agents The following products have been approved for cleaning the SIMATIC MV320: Wipes soaked in alcohol Clorox disinfecting wipes Clorox bleach solution (10% bleach, 90% tap water) Medical DiAirKem Sani-Cloth HB, Super Sani-Cloth germicidal, Sani-Cloth Plus germicidal disposable wipes Virex II disinfectant cleaner Operating Instructions, 08/2015, C79000-G8976-C

44 Service and maintenance 44 Operating Instructions, 08/2015, C79000-G8976-C352-03

45 Technical data 9 SIMATIC MV320 Memory capacity Communication Interfaces Field selection Dimensions and weight 6GF3320-0HT MB flash ROM / 32 MB RAM RS-232, USB 2.0 (generic, keyboard, virtual COM port) Near field or wide field Dimensions, H x L x W in mm 140 x 70 x 50 Weight Color Permitted ambient conditions Degree of protection kg Dark gray IP54 Operating temperature C Storage temperature C Humidity Impact resistance Resistant to ambient light Electrical data/power requirements Reader at 5 VDC (ma) Typical < 450 ma Idling < 80 ma Sleep mode < 31 ma Decoding capability %, no condensation Resistant to being dropped repeatedly on concrete from a height of 1.8 m Sunlight: up to lx 1D codes Codabar, Code 11, Code 32, Code 39, Code 93, Code 128, Interleaved 2 of 5, GS1 DataBar (RSS), Hong Kong 2 of 5, Matrix 2 of 5, MSI Plessey, NEC 2 of 5, Pharmacode, Plessey, Straight 2 of 5, Telepen, Trioptic, UPC/EAN/JAN Stacked 1D codes 2D codes Postal codes Codablock F, GS1 Composite (CC-A/CC-B/CC- C), MicroPDF, PDF417 Aztec Code, Data Matrix, Han Xin, MaxiCode, Micro QR Code, QR Code Australian, Intelligent Mail, Japan Post Group, KIX Code, Korea Post, Planet,Postnet, Royal Mail Group Ltd, UPU ID-tags Operating Instructions, 08/2015, C79000-G8976-C

46 Technical data Optical data Read field 6GF3320-0HT01 Near field 30 x 20 (horizontal x vertical) Wide field 50 x 33.5 (horizontal x vertical) Read distance Sensor Optical resolution Approx. 100 mm Near field 960 x 640 Wide field 960 x 640 Roll angle Angle of inclination Rotational tolerance ± 180 Print contrast resolution Target beam CMOS 1.2 megapixels (1280 x 960) gray shades ±60 (from front to rear) ± 60 level parallel to symbol (between sides) 25% (1D codes) or 35% (2D codes) absolute dark/light reflectance differential measured at 650 nm Single, blue target strip SIMATIC MV325 Memory capacity Bluetooth modem Communications interfaces Operating modes Field selection Time stamp Dimensions and weight Dimensions, H x L x W in mm 6GF3325-0HT MB flash ROM / 32 MB RAM USB 2.0 (generic, keyboard, virtual COM port) Bluetooth (Class II) Near field or wide field Interval logging Reader 135 x 130 x 51 Charging station 60 x 115 x 83 Weight Reader kg Battery 0.48 kg Charging station with integrated Bluetooth modem kg 46 Operating Instructions, 08/2015, C79000-G8976-C352-03

47 Technical data Permitted ambient conditions Degree of protection 6GF3325-0HT01 IP65 Operating temperature C Storage temperature C Humidity Impact resistance Resistant to ambient light Electrical data/power requirements Reader at 4.2 VDC (ma) Typical and peak 362 ma Idling 80 ma Sleep mode 20 ma Charging station with integrated Bluetooth modem at 5 VDC (ma) Max. USB charging current 555 ma USB trickle charge current 165 ma Charging station with external Bluetooth modem at 5 VDC (ma) Max. USB charging current 514 ma Decoding capability %, no condensation Resistant to being dropped repeatedly on concrete from a height of 1.8 m Sunlight: up to lx 1D codes Codabar, Code 11, Code 32, Code 39, Code 93, Code 128, IATA 2 of 5, Interleaved 2 of 5, GS1 DataBar (RSS), Hong Kong 2 of 5, Matrix 2 of 5, MSI Plessey, NEC 2 of 5, Pharmacode, Plessey, Straight 2 of 5, Telepen, Trioptic, UPC/EAN/JAN Stacked 1D codes Codablock F, GS1 Composite (CC-A/CC-B/CC- C), MicroPDF, PDF417 2D codes Aztec Code, Data Matrix, Han Xin, MaxiCode, Micro QR Code, QR Code Postal codes Australian, Intelligent Mail, Japan Post, KIX Code, Korean Post, Planet, Postnet, UK Royal Mail, UPU ID-tags Optical data Read field Near field 30 horizontal by 20 vertical Wide field 50 horizontal by 33.5 vertical Read distance Sensor Approx. 100 mm CMOS 1.2 megapixels (1280 x 960) gray shades Operating Instructions, 08/2015, C79000-G8976-C

48 Technical data Optical resolution 6GF3325-0HT01 Near field 960 x 640 Wide field 960 x 640 Roll angle Angle of inclination Rotational tolerance ± 180 Print contrast resolution Target beam Number of scanning operations ±60 (from front to rear) ± 60 level parallel to symbol (from side to side) 25% (1D codes) or 35% (2D codes) absolute dark/light reflectance differential measured at 650 nm Single, blue target strip Up to scans/charge Read distances The read distances are made up of a wide field and a near field. All code patterns must be of high quality and on a physical midline at an angle of 10 when read. The table refers to the AGC factory settings; accuracy: ± 10 % Table 9-1 Read distances Test code Min. mm Max. mm 3 mil Code mil Code mil GS1 DataBar mil UPC mil Data Matrix mil Data Matrix mil Data Matrix mil Data Matrix mil Data Matrix mil = mm The ideal read distance is about 100 mm. Depending on the code type and code size, smaller or larger distances are possible. 48 Operating Instructions, 08/2015, C79000-G8976-C352-03

49 Dimension drawings 10 All dimensions in mm Figure 10-1 SIMATIC MV320 dimension drawing Operating Instructions, 08/2015, C79000-G8976-C

50 Dimension drawings Figure 10-2 SIMATIC MV325 dimension drawing Figure 10-3 SIMATIC MV325 charging station dimension drawing 50 Operating Instructions, 08/2015, C79000-G8976-C352-03

51 Ordering data 11 Table 11-1 ordering data SIMATIC MV320 Handheld reader SIMATIC MV325 Handheld reader with battery, charging station and USB cable (0.9 m) Article number 6GF3320-0HT01 6GF3325-0HT01 Table 11-2 SIMATIC MV320 accessories ordering data Article number Power supply unit 1) EU 6GF3020-0AC40-0AP2 USA 6GF3020-0AC40-0AP1 Power supply unit 2) EU 6GF3320-0AC04 USB cable (1.8 m) 6GF3320-0AC02 RS-232 cable, coiled (2.4 m) 6GF3320-0AC03 Metal stand 6GF3320-0AC07 1) Delivery possible until 10/2015 2) Delivery possible from 10/2015 Table 11-3 SIMATIC MV325 accessories ordering data Charging station with USB interface Bluetooth wireless interface and USB cable (0.9 m) Battery lithium-ion mah, charging cycles Bluetooth M3 modem 1) RS-232 cable, coiled (2.4 m) 1) Article number 6GF3325-0AC03 6GF3325-0AC07 6GF3325-0AC05 6GF3325-0AC06 1) Delivery possible from 10/2015 Operating Instructions, 08/2015, C79000-G8976-C

52 Ordering data 52 Operating Instructions, 08/2015, C79000-G8976-C352-03

53 Appendix A A.1 Code configurations Note Changing the configuration Changes to the configuration take effect immediately and are stored. Note Rate of data transmission depends on set keyboard Note that the data transmission rate is slower with a set universal keyboard (Universal Keyboard Mapping) than with selection of a specific keyboard language (e.g. US keyboard). SIMATIC MV320 Codes for configuration of the device A current list of the codes for configuration of the SIMATIC MV320 reader is available at the following link: SIMATIC MV320 Configuration guide ( Motion detection with the reader with and without stand detection If the reader is placed on a stand, the reader with stand detection automatically switches to the motion detection mode. When the code for "Disable Motion Detection with Stand Detection" is scanned in, the reader switches to the motion detection mode. Detection depends on whether or not the reader is on a stand. To disable motion detection, you need to scan in the code for "Disable Motion Detection with Stand Detection" and "Motion Detection Scanning Off". To enable motion detection on readers with stand detection after disabling motion detection: You need to scan in the code for "Enable Motion Detection with Stand Detection" To enable motion detection on readers without stand detection: You need to scan in the required code for "Motion Detection On". Operating Instructions, 08/2015, C79000-G8976-C

54 Appendix A.2 "Specify character length to be read" function SIMATIC MV325 A current list of the codes for configuration of the SIMATIC MV325 reader is available at the following link: SIMATIC MV325 Configuration guide ( A.2 "Specify character length to be read" function Description of the function With the help of this function, you can specify the code character length to be read by the SIMATIC MV320 and SIMATIC MV325 handheld readers. When you enable this function, the handheld readers will only read codes that have exactly the character length you have specified. This function is particularly useful when multiple codes with different character lengths are printed on the product that is to be scanned. Enabling/disabling the function Enable Follow these steps to enable the function: 1. Scan the following code to enable the function: 2. Scan the following code to restart the handheld reader: 54 Operating Instructions, 08/2015, C79000-G8976-C352-03

55 Appendix A.2 "Specify character length to be read" function 3. For SIMATIC MV325: Scan the "QuickConnectCode" on the charging station. 4. Scan the required character length code with which you specify which codes with which character length are to be read. The table below contains the character length codes. Disable Follow these steps to disable the function: 1. Scan the device-specific reset code: MV320: MV325: When the reset code is scanned, the handheld reader is reset to the factory settings and restarted. Operating Instructions, 08/2015, C79000-G8976-C

56 Appendix A.2 "Specify character length to be read" function Character length codes The table below contains the codes with which you can specify the permitted character length as described in step 4 above. Table A- 1 Character length codes 1 character 2 characters 3 characters 4 characters 5 characters 6 characters 7 characters 8 characters 9 characters 10 characters 11 characters 12 characters 13 characters 14 characters 15 characters 16 characters 17 characters 18 characters 19 characters 20 characters 21 characters 22 characters 23 characters 24 characters 56 Operating Instructions, 08/2015, C79000-G8976-C352-03

57 Appendix A.3 Service and Support A.3 Service and Support Technical Support You can contact Technical Support for all Process Industries and Drives products as follows: Phone: + 49 (0) Fax: + 49 (0) (mailto:support.automation@siemens.com) Internet: Online support request form: ( Contact partner If you have any further questions on the use of our products, please contact one of our representatives at your local Siemens office. The addresses are found on the following pages: On the Internet ( In Catalog CA 01 In the catalog ID 10 for Industrial identification systems Service and Support at Process Industries and Drives (PD) You will find various services on the Support homepage ( of PD on the Internet. There you will find the following information, for example: Our newsletter containing up-to-date information on your products. Relevant documentation for your application, which you can access via the search function in "Product Support". A forum for global information exchange by users and specialists. Your local PD representative. Information about on-site service, repairs, spare parts, and much more can be found under "Our service offer". SIMATIC Ident home page For the latest general information about our identification systems, visit us on the Internet at Identification systems home page ( Operating Instructions, 08/2015, C79000-G8976-C

58 Appendix A.3 Service and Support SIMATIC documentation on the Internet A guide to the technical documentation for the various SIMATIC products and systems is available on the Internet: SIMATIC Guide manuals ( Online catalog and ordering system The online catalog and the online ordering system can also be found on the Industry Mall home page ( Training center We offer appropriate courses to get you started. Please contact your local training center or the central training center in D Nuremberg. Phone: +49 (0) ( 0.14 /min. from the German landline network, deviating mobile communications prices are possible) For information about courses, see the SITRAIN homepage ( 58 Operating Instructions, 08/2015, C79000-G8976-C352-03

59 Appendix A.4 Certificates and approvals A.4 Certificates and approvals According to the conditions of the guarantee, the product guarantee becomes void if the housing is opened or handled improperly. SIMATIC MV320 CE marking Description Conformity with EMC directive. FCC standard Description FCC CFR 47 Part15-Digital Devices, Subpart B-Unintentional Radiators, Class B (October 1st 2011). This device is equivalent to the CR1400-Handheld from CodeCorp. SIMATIC MV325 (reader and charging station) CE marking Description Conformity with the R&TTE directive. Operating Instructions, 08/2015, C79000-G8976-C