FA-M3 FA Link H Modules FA-bus Modules. Contents. F3LP02-0N FA Link H Module F3LP12-0N Fiber-Optic FA Link H Module... 5

Transcription

1 <<Contents>> <<Index>> GS M06H-0E FA Link H Modules FA-bus Modules Contents FLP0-0N FA Link H Module... FLP-0N Fiber-Optic FA Link H Module... 5 FLR0-0N Fiber-Optic FA-bus Module... 7 FLR0-0N Fiber-Optic FA-bus Type Module... 9 FLR0-W FA-bus Type Module... Yokogawa Electric Corporation GS M06H-0E Copyright 0 0th Edition Aug. 0

2 Blank Page

3 <<Contents>> <<Index>> FLP0-0N FA Link H Module The FLP0-0N FA Link H Module provides a high-speed network that allows information exchange between the Range-free Multi-controllers. The FLP0-0N is an FA link H interface module that provides a maximum of stations of data link (one module is counted as one station). - It allows a maximum of eight modules to be installed in a single main unit, to make up a multi-layer data link. The module can be accessed only from a designated CPU. - The number of link points can be specified arbitrarily for each CPU. - Bus-type communication channels are employed to facilitate the expansion of modules. - FA Link H Modules can be connected easily using a two-twisted-pair (-wire) shielded cable. Specification Number of stations max. Link relays 08 per module - FSP05/08 and FSP: 08 - FSP/5/8/5/5/66 and FSP7-S: 89 (non-continuous) - FSP8/58/59/67 and FSP76-7S: 6,8 (non-continuous) Link register 08 per module - FSP05/08 and FSP: 08 - FSP/5/8/5/5/66 and FSP7-S: 89 (non-continuous) - FSP8/58/59/67 and FSP76-7S: 6,8 (non-continuous) Maximum. Number of links per station Same as above. Link relay and link register assignments Link relay: on 6-relay basis Link register: on per register basis Number of modules FSP05/08 and FSP: max. FSP, FSP5, FSP8, FSP5, FSP8, FSP5, FSP58/59, FSP66/67, FSP7-S and FSP76-7S:8 max. Transmission speed 5 K, 50 K, 65 K or.5 Mbps (switch selectable) Transmission channel type -bus type Termination resistance 0 Ω at both ends (specified by a built-in switch when the line is terminated) Transmission distance km, 500 m, 50 m or 00 m (depends on transmission speed) Communication system Token-bus system Synchronization Frame synchronization Transmission format Conforms to HDLC. Modulation and encoding system NRZI system Error detection CRC-CCITT, timeout RAS features Error detection through local loopback, hardware self-diagnostics, special relay and register functions Transmission media Two-twisted-pair (-wire) shielded cable (AWG0) Current consumption 70 ma External connection -point terminal block, M.5 screws External dimensions 8.9 (W) x 00 (H) x 8. (D) mm (Note) Weight 0 g Surrounding air Operating :0 to 55 C temperature range Storage :-0 C to 75 C Surrounding humidity Operating :0 to 90% RH (non-condensing) range Storage :0 to 90% RH (non-condensing) Surrounding atmosphere Must be free of corrosive gases, flammable gases or heavy dust. Note: The given dimensions exclude protrusions (See External Dimensions for details). Note: FLP0-0N is not compatible with FSP7-N and FSP76-7N. Components and Functions Front View RDY SND ERR LP0-0N STATION NO. TERMINATOR OFF ON A B SG SHIELD Right Side View Indicators RDY: Lit when the internal circuit is functioning normally. SND: Lit when the module is sending data normally. ERR: Lit when an error occurs. Station No. switch (STATION No.): Sets a station number (0 to ). The factory setting is 0. Terminator switch (TERMINATOR): ON : Terminator is enabled. OFF: Terminator disabled. The factory setting is OFF. FA link H terminal block ( terminals, M.5 screws) Parameter switches Note: This figure is drawn with the panel cover removed. Factory No. No. Parameter OFF ON Switch setting OFF ON Transmission See table OFF No. OFF.5 Mbps 50 Kbps speed to the right. OFF ON 65 Kbps 5 Kbps Operation High Normal OFF mode speed (Not used) OFF All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

4 <<Contents>> <<Index>> System Configuration Example. Connecting between Controllers The FLP0-0N can be used to configure a system in which communication speed can be as high as.5 Mbps. FLP0-0N FA Link H module FA Link H modules (.5 Mbps max., km max., stations). Connecting between Controllers, FA500 and µfa0 FLP0-0N FA Link H Module FLP0-0N FA Link H Module LP0-0N FA Link Module FA500 for FA500 µfa0 FA link 50 kbps (500 m max., stations) - Set the transmission speed of the FA Link H module to 50 kbps. External Connection Diagram Terminating resistor FA link H module A B SG SHIELD FA link H module A B SG SHIELD Maximum total cable length: S m FA link H module A B SG SHIELD Terminating resistor. The maximum total cable length (S) varies depending on the transmission speed used.. The SHIELD terminal of this module is internally connected to the FG terminal of the power supply module.. This module has a built-in terminator. When configuring the module at the end of the cable, set the terminator switch to ON. Cables Use two-pair (-wire) shielded cable (impedance 00 Ω ) when connecting FA Link H modules. Recommended cables: KM80- /KM8- (to be purchased separately). * For details on KM80- and KM8-, see YHLS Master Module, YHLS Slave Units and YHLS Communication Cables (for implementing high-speed remote I/O) (GS M06H6-0E). Operating Environment - The table below lists the CPU modules that can be used with this module. CPU Module FSP, FSP5 and FSP5 FSP05/ 08, FSP, FSP8, FSP8, FSP5/58/59, FSP66/67, FSP7-S, FSP76-7S Style No. and ROM Rev. S Rev. 8 or later Note: For the revision number of a CPU module, see the revision number label on the side panel. - The following table summarizes the requirements for the Ladder Diagram Support Program M, which can be used to set up the communications conditions of this module. All versions of the Ladder Programming Tool WideField, WideField and WideField can be used with this module. Ladder Diagram Support Revision Program M SF50-E Rev..08 or later Model and Suffix s Model Suffix Style Option FLP0-0N External Dimensions stations max. 5 k, 50 k, 65 k or.5 Mbps km, 500 m, 50 m or 00 m Unit:mm 00 FB05.VSD All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

5 <<Contents>> <<Index>> 5 FLP-0N Fiber-optic FA Link H Module The FLP-0N Fiber-optic FA Link H Module is a high-speed network that allows information exchange between the Range-free Multi-controllers. The FLP-0N is a Fiber-optic FA link H interface module that provides a maximum of stations of data link (one module is counted as one station). - It allows a maximum of eight modules to be installed in a single main unit, to making up a multi-layer data link. The module can only be accessed from a designated CPU. - The number of link points can be specified arbitrarily for each CPU. - It supports daisy-chain configuration using fiber-optic cables. - It does not guarantee normal data link in the entire network if any one station on the network is powered off. Number of stations Link relays Link registers Max. number of links per station Link relay and link register assignments Number of modules Specification max. 08 per module - FSP05/08 and FSP: 08 - FSP/5/8/5/5, 66 and FSP7-S: 89 (non-continuous) - FSP8/58/59/67 and FSP76-7S:6,8 (non-continuous) 08 per module - FSP05/08 and FSP: 08 - FSP/5/8/5/5/66 and FSP7-S: 89 (non-continuous) - FSP8/58/59/67 and FSP76-7S: 6,8 (non-continuous) Same as above. Link relay: on 6-relay basis Link register: on per register basis FSP05/08 and FSP: max. FSP, FSP5, FSP8, FSP5, FSP8, FSP5, FSP58/59, FSP66/67, FSP7-S, FSP76-7S: 8 max. Transmission speed.5 Mbps Transmission channel type Daisy chain Transmission Maximum total distance: 0 km distance Maximum distance between stations: km Communication Token ring system Synchronization Frame synchronization Transmission format Conforms to HDLC. Modulation and encoding system NRZI system Error detection CRC-CCITT RAS feature Self-diagnostics -core optical fiber (hard plastic clad quartz Transmission media fiber-optic H-PCF) Current consumption 95 ma External dimensions 8.9 (W) x 00 (H) x 8. (D) mm Weight 0 g Surrounding air Operating :0 to 55 C temperature range Storage :-0 C to 75 C Surrounding humidity Operating :0 to 90% RH (non-condensing) range Storage :0 to 90% RH (non-condensing) Surrounding Must be free of corrosive gases, flammable atmosphere gases or heavy dust. Note: FLP-0N is not compatible with FSP7-N and FSP76-7N. Components and Functions Front View RDY SND ERR LP-0N STATION NO FALINK Right Side View Indicators RDY: Lit when the internal circuit is functioning normally. SND: Lit when the module is sending data normally. ERR: Lit when an error occurs. Station No. switch (STATION No.): Sets a station number (0 to ). The factory setting is 0. Fiber-optic connector Attach a dust cap in the port not used. O F F Parameter switches F0.VSD Note: This figure is drawn with the panel cover removed. No. Parameter OFF ON Factory setting Intermediate Terminal Intermediate station station station OFF (Not used) OFF Operation mode Normal High speed OFF (Not used) OFF All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

6 <<Contents>> <<Index>> 6 Configuration Example External Dimensions Daisy-chain configuration Unit: mm FLP-0N Fiber-optic FA Link H module Fiber-optic FA Link H. The maximum distance between stations is km and the maximum total distance is 0 km.. The attached blank cover must be placed on any unused port of the terminating station. Operating Environment - There is no restriction on the type of CPU modules that can be used with this module. CPU Module Style No. and ROM Rev. FSP, FSP5 and FSP5 S Rev. 8 or later FSP05, FSP 08, FSP, FSP8, FSP8, FSP5/58/59,FSP66/67, FSP7-S, FSP76-7S Note: For the revision number of a CPU module, see the revision number label on the side panel. - The following table summarizes the requirements for the Ladder Diagram Support Program M, which can be used to set up the communications conditions of this module. All versions of the Ladder Programming Tool WideField, WideField and WideField can be used with this module. Ladder Diagram Support Revision Program M SF50-E Rev..08 or later Model and Suffix s Model Suffix Style Option FLP -0N stations max. Maximum total distance: 0 km Maximum distance between stations: km.5mbps Optional Accessories The customer should prepare fiber-optic cables satisfying the requirements listed below when connecting between Fiber-optic FA Link H modules. See Fiber-optic Cables (GSM06C9-0E) for details on fiber-optic cables. for Fiber-optic Cable Cores Yokogawa Cable Model Number KM60 KM60,KM6,KM6,KM65 Fiber-optic Cable Model No.(Size) DK-HPF00/0 CCV-HC-0/07 Fiber-optic Cable type SI type SI type Vendor SWCC Showa Sumitomo Electric Cable System Core diameter 00±5μm Clad diameter μm Transmission loss 7.0dB/km Max. 7dB/km Max. (λ=0.85μm,ta=5 ) (λ=0.8μm,ta=5 ) :Step-index optical fiber for Fiber-optic Cable Connectors Yokogawa Cable Model Number Optical connectors Model No. Vendor KM60 KF-07 SWCC Showa Cable Systems lever lock bonding, polished KM65 CF-0 CF-07 Sumitomo Electric lever lock, crimping, cut KM60,KM6 KM6 CF-00H CF-07H Sumitomo Electric lever lock bonding, polished All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

7 <<Contents>> <<Index>> 7 FLR0-0N Fiber-optic FA-bus Module The FLR0-0N is an interface module for constructing a system that requires distributed placement of multiple modules. The user can build up an efficient remote I/O system by installing FLR0-0N modules in the main- and sub-units and connecting them via a fiber-optic FA-bus (fiber-optic cable). - With the 0-Mbps high-speed communications capability of the FLR0-0N, the user does not have to worry about the I/O refresh time in ladder programming. - All I/O module types and most special module types* can be installed in sub-units and accessed just like modules installed in the main unit. *:See "Restrictions on System Configuration" - No specific communications setup (environment setup) is required. - The optical transmission system makes the FLR0-0N highly immune to noise. Specification Transmission speed 0 Mbps -core optical fiber (hard plastic clad Transmission media quartz fiber-optic H-PCF) Transmission distance Maximum total distance: 00 m Maximum distance between stations: 00 m Transmission configuration Star Maximum number of sub-units (systems) 7 (systems) Shutdown I/O contact output on transmission RAS features channel error, reporting of transmission channel error location Current consumption 0 ma External dimensions 8.9 (W) x 00 (H) x 8. (D) mm Weight 00 g Surrounding air Operating :0 to 55 C temperature range Storage :-0 C to 75 C Surrounding humidity Operating :0 to 90% RH (non-condensing) range Storage :0 to 90% RH (non-condensing) Surrounding atmosphere Must be free of corrosive gases, flammable gases or heavy dust. Note: The maximum number of systems when µ-bus master station module are used is system less than the value above for each µ-bus master station. Components and Functions Front View RDY ERR LR0-0N REMOTE SUB UNIT NO. Right Side View Indicators RDY: Lit when the internal circuit is functioning normally. ERR: Lit when the module fails to detect an input signal from a port. Unit No. switch (SUB UNIT No.) Sets a unit number (0 to 7). 0 : Unit number of the main unit -7: Unit number of the sub-units 8,9: Cannot be used. Fiber-optic connector O F F Condition switches (-pole DIP switch) No. ON OFF Factory Setting Shutdown output Hold output OFF ON *: Valid only for output modules installed in a subunit. Note: This figure is drawn with the panel cover removed. All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

8 <<Contents>> <<Index>> 8 System Configuration Example Star Configuration Unit No. 0 Main unit Unit No. Unit No. Unit No. Operating Environment There is no restriction on the type of CPU modules that can be used with this module. Model and Suffix s Model Suffix Style Option FLR0-0N Maximum total distance: 00 m Maximum distance between stations: 00 m Sub-units* FLR0-0N Fiber-optic FA-bus module for External Dimensions Unit: mm Daisy-chain + Star Configuration Unit No. 0 Main unit FA500 Unit No. Unit No. Unit No. Sub-units* FA500 Unit No. 5 *: Maximum number of sub-units: 7 Unit No. FLR0-0N Fiber-optic FA-bus module for LR0-0N Fiber-optic FA-bus module for FA500 Restrictions on System Configuration Maximum total distance Number of connectable sub-units Number of fiber-optic FA-bus modules installable in a main unit Number of fiber-optic FA-bus modules installable in a sub-unit Modules installable in a sub-unit 00 m 7 max. 7 max. (no restrictions on the installation location) (no restrictions on the installation location) All I/O modules, and special modules except FLP, FLE0, FLX0 and FNX0 modules. Optional Accessories Prepare fiber-optic cables satisfying the requirements listed below when connecting Fiber-optic FA-bus modules for extension. See Fiber-optic Cables (GS M06C9-0E) for details on fiber-optic cables. for Fiber-optic Cable Cores Yokogawa Cable Model Number KM60 KM60,KM6,KM6,KM65,KM69 Fiber-optic Cable Model No. (Size) DK-HPF00/0 CCV-HC-0/07 Fiber-optic Cable type SI type SI type Vendor SWCC Showa Sumitomo Electric Cable System Core diameter 00±5μm Clad diameter μm Transmission loss 7.0dB/km Max. 7dB/km Max. (λ=0.85μm,ta=5 ) (λ=0.8μm,ta=5 ) :Step-index optical fiber for Fiber-optic Cable Connectors Yokogawa Cable Model Number Optical connectors Model No. Vendor KM60 KF-07 SWCC Showa Cable Systems lever lock bonding, polished KM65 CF-0 CF-07 Sumitomo Electric lever lock, crimping, cut KM60,KM6 KM6,KM67,KM69 CF-00H CF-07H Sumitomo Electric lever lock bonding, polished All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

9 <<Contents>> <<Index>> 9 FLR0-0N Fiber-optic FA-bus Type Module The FLR0-0N is an interface module for constructing a system that requires distributed placement of multiple modules. The user can build up an efficient remote I/O system by installing FLR0-0N modules in the main- and sub-units and connecting them via a fiber-optic FA-bus (fiber-optic cable). - With the 0-Mbps high-speed communication capability of the FLR0-0N, the user does not have to worry about the I/O refresh time in ladder programming. - All I/O module types and most special module types* can be installed in sub-units and accessed just like modules installed in the main unit. *:See "Restrictions on System Configuration" - No specific communication setup (environment setup) is required. - The optical transmission system makes the FLR0-0N highly immune to noise. - A single sub-unit can be segmented into a maximum of 8 stations. - A -port (send/receive) system allows daisy-chain configuration. - The loop system is switched into two pairs of daisy-chain systems when a disconnection occurs in the system, thereby improving system reliability. Specification Transmission speed 0 Mbps -core optical fiber (hard plastic clad quartz Transmission media fiber-optic H-PCF) Transmission distance Maximum distance between stations: 500 m Maximum total distance:. km ( stations) Transmission configuration Star, daisy chain, loop Maximum number of sub-stations 56 Maximum number of systems 7 (Note) Maximum number of sub-stations per system Maximum total distance per system. km ( stations) Maximum distance between stations 500 m Shutdown I/O contact output on transmission RAS features channel error, reporting of transmission channel error location Current consumption 60 ma External dimensions 8.9 (W) x 00 (H) x 8. (D) mm Weight 0 g Surrounding air Operating :0 to 55 C temperature range Storage :-0 C to 75 C Surrounding humidity Operating :0 to 90% RH (non-condensing) range Storage :0 to 90% RH (non-condensing) Surrounding atmosphere Must be free of corrosive gases, flammable gases or heavy dust. Note: The maximum number of systems when µ-bus master station module are used is system less than the value above for each µ-bus master station. Components and Functions Front View RDY ERR ERR LR0-0N REMOTE SUB UNIT NO. LEFT SLOT NO. Indicators RDY: Lit when the internal circuit is functioning normally. ERR, : Lit when the module fails to ERR detect an input signal from a port. Unit No. switch (SUB UNIT No.): Sets a unit number (0 to 7). 0 : Unit number of the main unit -7 : Unit number of sub-units 8, 9 : Cannot be used. First slot number switch (LEFT SLOT NO.) Used to set the first slot number (hexadecimal) of the base module. Condition Switches Fiber-optic connector Attach a dust cap, in not using the port. No. Meaning OFF ON Factory set * Hold/reset output on Hold * Shutdown communication error output output ON Port used Port Both ports * OFF Channel configuration Daisy chain or star Loop OFF Reserved OFF *: Valid only for output modules installed in a sub-unit. *: Continues operation if transmission channel has been secured and system operation is continued. *: Both port and port are used. Light Power Setup Switches Distance between stations No. Meaning (Fiber-optic cable length) (m) 5 Port OFF ON OFF ON intensity OFF OFF ON ON 7 Port OFF ON OFF ON intensity OFF OFF ON ON Right Side View O F F 5 O 6 F 7 F 8 Note: This figure is drawn with the panel cover removed. All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

10 <<Contents>> <<Index>> 0 System Configuration Example Daisy-chain configuration main unit FLR0-0N Fiber-optic FA-bus Type module Fiber-optic FA-bus Substation Configuration - Substation Configuration Example The user can configure two or more sub-stations by splitting a sub-unit using the fiber-optic FA-bus type. A sub-unit logically consists of 6 slots. A maximum of 7 sub-units can be used with the main unit. Main unit Slot 6 stations max. Sub-unit Sub-unit Sub-unit 7 Loop configuration main unit FLR0-0N Fiber-optic FA-bus Type module Fiber-optic FA-bus - Split Patterns Sub-units can be split in several patterns. Select an appropriate pattern according to the configuration of your system. stations max. Split pattern FBU06 FBU06 FBU0 FBU0 FBU09 FBU0 FBU0 Slot No. FBU06 FBU0 FBU06 FBU0 FBU0 FBU0 FBU0 Number of sub-stations Free Free Free Free FBU0 FBU0 FBU0 FBU0 FBU0 Free FBU0 Free FBU0 Free FBU0 Free 8 Restrictions on System Configuration Number of Fiber-optic FA-bus Type modules installable in a master station Number of Fiber-optic FA-bus Type modules installable in a sub-station Modules installable in a sub-station 5 Max. All I/O modules, and special modules except FLP, FLE0, FLX0 and FNX0 modules. When pattern () is used, for example, it is possible to connect together up to 7 sub-units, providing a maximum of stations. A -station system (maximum configurable system) can be configured by combining 6 sets of pattern (5) and set of pattern (6). The number of I/O modules that can be installed in pattern (6) is module per sub-station. All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

11 <<Contents>> <<Index>> Number of s and Maximum Total Distance (m) Maximum Total Distance (m) Number of Daisy-chain Loop Subconfiguration configuration stations Number of Substations Maximum Total Distance (m) Daisy-chain Loop configuration Do not lay cables such that the actual fiber-optic cable length exceeds the Maximum total distance, or the distance between two stations exceeds the maximum distance allowed between stations (500 m). External Dimensions Unit: mm Operating Environment - The following table lists the type of CPU modules that can be used with this module. CPU Module Style No. and ROM Rev. * FSP, FSP5 and FSP5 S Rev. 8 or later * FSP05/08, FSP, FSP8, FSP8, FSP5/58/59, FSP66/67, FSP7/76 FBP0, FBP0 and FFP6 *: For the revision number of a CPU module, see the revision number label on the side panel. *: Supports logging of transmission channel error location. - The following table summarizes the requirements for the Ladder Diagram Support Program M, which can be used to set up the communications conditions of this module. All versions of the Ladder Programming Tool WideField and WideField can be used with this module. Ladder Diagram Support Program M Revision SF50-E Rev..08 or later *: Supports logging of transmission channel error location. - The following table lists the type of base modules that can be used with this module. Base Module ID Mark FBU0 R 0 or later FBU05 FBU06 R 0 or later FBU09 FBU FBU6 Model and Suffix s Model Suffix Style Option FLR0-0N Maximum total distance:. km Maximum distance between stations: 500 m Optional Accessories Prepare fiber-optic cables satisfying the requirements listed below when connecting Fiber-optic FA-bus Type modules for extension. See Fiber-optic Cables (GS M06C9-0E) for details on fiber-optic cables. for Fiber-optic Cable Cores Yokogawa Cable Model Number Fiber-optic Cable Model No. (Size) Fiber-optic Cable type Vendor Core diameter KM60 KM60,KM6, KM6,KM65,KM69 KM67 DK-HPF00/0 CCV-HC-0/07 CCV-HG-0/08 SI type SI type GI type SWCC Showa Sumitomo Electric Cable System 00±5μm Clad diameter Transmission loss 7.0dB/km Max. (λ=0.85μm, Ta=5 ) :Step-index optical fiber :Graded-index optical fiber -0 μm 7dB/km Max. (λ=0.8μm, Ta=5 ) 8dB/km Max. (λ=0.8μm, Ta=5 ) for Fiber-optic Cable Connectors Yokogawa Cable Model Number Optical connectors Model No. Vendor KM60 KF-07 SWCC Showa Cable Systems lever lock bonding, polished KM65 CF-0 CF-07 Sumitomo Electric lever lock, crimping, cut KM60,KM6 KM6,KM67,KM69 CF-00H CF-07H Sumitomo Electric lever lock bonding, polished All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

12 0 5 <<Contents>> <<Index>> FLR0-W FA-bus Type Module The FLR0-W is an interface module for constructing a system that requires distributed placement of multiple modules. The user can build up an efficient remote I/O system by installing FLR0-W modules in the main- and sub-units and connecting them via a FA-bus. - With the 0-Mbps high-speed communication capability of the FLR0-W, the user does not have to worry about the I/O refresh time in ladder programming. - All I/O module types and most special module types* can be installed in sub-units and accessed just like modules installed in the main unit. *:See "Restrictions on System Configuration" - Both daisy-chain and loop configuration options are supported. - The loop system is switched into two pairs of daisy-chain systems when a disconnection occurs in the system. Specification Transmission speed 0 Mbps two-pair (-wire) shielded cable Transmission media (impedance 00Ω) Maximum total distance:70m Transmission distance Maximum distance between stations: 0 m Transmission configuration Star, daisy chain, loop Maximum number of subunits (systems) 7 (Note) Shutdown I/O contact output on transmission RAS features channel error, reporting of transmission channel error location Must be installed inside panel enclosure or Installation location system Current consumption 0 ma External dimensions 8.9 (W) x 00 (H) x 8. (D) mm Weight 05 g Surrounding air Operating : 0 to 55 C temperature range Storage : -0 C to 75 C Surrounding humidity Operating : 0 to 90% RH (non-condensing) range Surrounding atmosphere Storage : 0 to 90% RH (non-condensing) Must be free of corrosive gases, flammable gases or heavy dust. Note: The maximum number of systems when µ-bus master station modules are used is system less than the value above for each µ-bus master station. The combined maximum number of systems is 7 when FA bus- modules are used with Fiber-optic FA bus- modules and Fiber-optic FA bus modules. Components and Functions Front View RDY ERR ERR LR0-W REMOTE R- R+ T- T+ 7 6 SHIELD SUB UNIT NO. R- R+ T- T+ Right Side View Front Indicators RDY ERR, ERR : Lit when the internal circuit is functioning normally. : Lit when the module fails to detect an input signal from a port. Unit No. Indicator 0 : Unit number of the main unit -7 : Unit number of sub-units Communication port O F F Rear This figure is drawn with the panel cover removed. Parameter switches Condition Switches SW No. Meaning OFF ON Factory setting * Hold/reset output on communication error * Hold output Shutdown output ON Port used Port Both ports * OFF Channel configuration Daisy chain or star Loop OFF Reserved OFF *: Valid only for output modules installed in a sub-unit. *: Continues operation if transmission channel has been secured and system operation is continued. *: Both port and port are used. All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

13 <<Contents>> <<Index>> System Configuration Example Daisy-chain configuration Main unit FLR0-W FA-bus Type module FA-bus Type Operating Environment - The following table lists the type of CPU modules that can be used with this module. CPU Module Style No. and ROM Rev. * FSP, FSP5 and FSP5 S Rev. 8 or later * FSP05, FSP08, FSP, FSP8, FSP8, FSP5, FSP58/59, FSP66/67, FSP7/76 FBP0, FBP0 and FFP6 *: For the revision number of a CPU module, see the revision number label on the side panel. *: Supports logging of transmission channel error location. Loop configuration Main unit FLR0-W FA-bus Type module FA-bus Type 7 stations max. 7 stations max. - The following table summarizes the requirements for the Ladder Diagram Support Program M that can be used with the module. All versions of the Ladder Programming Tool WideField, WideField and WideField can be used with this module. Ladder Diagram Support Program M Revision SF50-E Rev..08 or later * *: Supports logging of transmission channel error location. - All versions of the Ladder Programming Tool WideField can be used with this module. Model and Suffix s Model Suffix Style Option FLR0 -W External Dimensions Maximum total distance: 70 m Maximum distance between stations: 0 m Restrictions on System Configuration Number of FA-bus Type modules 7 installable in a main unit Number of FA-bus Type modules installable in a subunit All I/O modules, and special modules except FLP, Modules installable in a subunit FLE0, FLX0 and FNX0 modules, Cables Use two-pair (-wire) shielded cable (impedance 00Ω) when connecting FA-bus Type modules. Recommended cable: KM80- (tested for noise immunity, to be purchased separately) * For details on KM80-, see GSM6H6-0E. All Rights Reserved. Copyright 0, Yokogawa Electric Corporation GS M06H-0E Aug., 0-00

14 <<Contents>> <<Index>> s to Specify When Ordering. Model and suffix codes All Rights Reserved. Copyright 0, Yokogawa Electric Corporation Subject to change without notice. GS M06H-0E Aug., 0-00