DAL4 REPEATER MODEL. (SIN-NET, M-Bus use) MODEL & SUFFIX CODE SELECTION DAL4 TRANSMISSION ORDERING INFORMATION RELATED PRODUCTS GENERAL SPECIFICATIONS

Transcription

1 REPETER (SIN-NET, M-us use) MODEL DL MODEL & SUFFIX CODE SELECTION MODEL CLE & PORT TYPE : Twisted-pair cable, ports : Fiber optics (PCF), ports Twisted-pair cable, port 5 : Fiber optics (I-50 nm), port Twisted-pair cable, port : Fiber optics (I-50 nm), port Twisted-pair cable, port INPUT M: 00 0V C R : V DC ORDERIN INFORMTION Specify code number. (e.g. DL--M) DL RELTED PRODUCTS Standard multi-transmission unit (model: DL) Remote I/O unit (model: DL) Multi-transmission module (model: L) Lightning surge protector for MsysNet (model: MDP-DM) ENERL SPECIFICTIONS Construction: Stand-alone; terminal access at the front Connection: M.5 screw terminals Housing material: Flame-resistant resin (black) Isolation: Transmission section to power PPLICLE NETWORK SIN-NET M-us 5 (.5) (.) 5 (.5) mm (inch) Functions & Features Extending No. of field devices and transmission distance for DL, DL ranching Transmission media conversion (twisted-pair from/to fiber optics) circuit incorporated in each port Typical pplications Exceeding kilometer (0 ft) distance with DL or DL Using more than DL or DL units TRNSMISSION TWISTED-PIR CLE: CPEV-0. dia. kilometer max. with field units; kilometers max. between two DL FIER OPTICS CLE PCF: kilometer max. Link type JIS F0 connector; pplicable fiber HC-0/0 (SUMITOMO) Core/clad dia. 00/0 µm Max. loss d I-50 nm (DL-5):.5 kilometers max. Connector type JIS F0 connector; pplicable fiber Core/clad dia. 50/ µm Max. loss d I-50 nm (DL-): kilometers max. Connector type JIS F0 connector; pplicable fiber Core/clad dia. 50/ µm Max. loss d Total of connection and transmission loss P. / 5 ES- Rev.

2 DL INSTLLTION Power input C: Operational voltage range 5 V, Hz, approx. V DC: Operational voltage range V ±0%, ripple 0% p-p max., approx. 50m Operating temperature: -5 to 55 C ( to F) -5 to 50 C ( to F) for DL- Operating humidity: 0 to 0% RH (non-condensing) Mounting: Surface or DIN rail Size: W5 H5 D mm (.5".5".") Weight: 00 g (0. lbs) SCHEMTIC CIRCUITRY & CONNECTION DIRM DL- PORT- Isolation Transceiver Transceiver Jumper Pin PORT- 5 Transceiver Isolation Jumper Pin Jumper Pin 0 F U() V() DL- FIER OPTICS LINK Transceiver FIER OPTICS LINK Jumper Pin 0 U() V() DL-5, FIER OPTICS FIER OPTICS PORT- TXD PORT- RXD Transceiver PERFORMNCE Insulation resistance: 00MΩ with 500V DC (PORT- to PORT- to to power) Dielectric strength: 00V minute (PORT- to PORT- to to power to ground) F Jumper Pin 0 F U() V() When the unit is located at the end of transmission line via twisted-pair cable (= no cross-wiring), short across these terminals. Do not short them for the one not located at the end. When the DL is to be connected with the L or DL multi transmission devices, do not connect the shield wire to the S (, or ) but to the F at the instrumentation panel. rounding the F improves noise immunity of the power and transmission lines, and is a recommended practice when the DL is installed where a noise is present. Specifications subject to change without notice. P. / 5 ES- Rev.

3 EXTERNL DIMENSIONS & TERMINL SSINMENT mm (inch) DL- (.) M.5 5. (.) dia. or. (.) dia. MT HOLE (.) deep DIN RIL 5mm wide 5 (.5) 5 TERMINL 5. (.) 0 5 (.5) (.) [. (.)] DL- (.) M.5 5. (.) dia. or. (.) dia. MT HOLE (.) deep DIN RIL 5mm wide 5 (.5) 5 TERMINL 5. (.) 0 5 (.5) (.) [. (.)] DL-5, (.) M.5 5. (.) dia. or. (.) dia. MT HOLE (.) deep DIN RIL 5mm wide 5 (.5) 5 RXD TXD TERMINL 5. (.) 0 5 (.5) (.) [. (.)] P. / 5 ES- Rev.

4 DL MOUNTIN REQUIREMENTS mm (inch) M5 S 0 (.) M S 0 (.) 0 (.) M5 50 (.) M Specifications subject to change without notice. P. / 5 ES- Rev.

5 LIHTNIN SURE PROTECTION MULTIPLEX TRNSMISSION MDP-DM DL- DL, L MDP-DM C C C 5 0 PNEL resistor Remarks e sure to use lightning surge protectors (model: MDP-DM) on twisted-pair cables. e sure to connect the terminal No. of the MDP-DM with S terminal of the DL. For connecting model DL or L with the DL in the same panel, install them between the MDP-DM and the DL. e sure to connect the terminal No. of the MDP-DM with S terminal of the DL. Lightning surge protectors for power supply line are recommended for complete protection. M-US MDP-DM C DL- DL, SMLM MDP-DM C C 5 S S 0 PNEL resistor Remarks e sure to use lightning surge protectors (model: MDP-DM) on twisted-pair cables. e sure to connect the terminal No. of the MDP-DM with S terminal of the DL. For connecting model DL or SMLM with the DL in the same panel, install them between the MDP-DM and the DL. e sure to connect the terminal No. of the MDP-DM with S terminal of the DL. Lightning surge protectors for power supply line are recommended for complete protection. P. 5 / 5 ES- Rev.