UL8750, UL1012, EN61347, BIS R Output Safety Certifications Approved. Output Power. Parameter Min. Typ. Max. Unit Remark

Size: px

Start display at page:

Download "UL8750, UL1012, EN61347, BIS R Output Safety Certifications Approved. Output Power. Parameter Min. Typ. Max. Unit Remark"

Shon Campbell
5 years ago
Views:

PISE-A040A (Pb-Free) 40W Selectable Output Power 38V - 77V / 0.35A - 0.

Outline (Metal Case) - 148.2 x 59.6 x 33.

Current Output Power Efficiency THD Com. Surge 108-305 38-77 0.35-0.7A Max. 40W Up to 88% < 20% 6kV 4kV > 0.9 Diff.

1 PISE-A040A (Pb-Free) 40W Selectable Output Power 38V - 77V / 0.35A - 0.5A - 0.7A / 40W Features Dimmable Type : 1-10 Dimming Input Cable : Double or Reinforced Insulation Selectable Output Current (0.35A / 0.5A / 0.7A) Constant Voltage / Constant Current Control High Efficiency & Active Power Factor Correction Protection : UVP, OVP, SCP, OTP and OCP Mechanical Outline (Metal Case) x 59.6 x 33.8mm UL8750, UL1012, EN61347, BIS R Output Safety Certifications Approved IP66 Critical Specifications Input Voltage Output Voltage Output Current Output Power Efficiency THD Com. Surge A Max. 40W Up to 88% < 20% 6kV 4kV > 0.9 Diff. PF Input Specifications Input Voltage VAC Input Current Vin=108V / Max. Load Input Frequency Hz Power Factor Over 75% Output Load Inrush Current - 60 Apk Based on IEC60555 Output Specifications Output Voltage VDC Output Current / 0.5 / A Selectable Output Current Output Dimming Current Range % 1-10 Dimming Output Current Tolerance Max. Output Current Output Ripple Current % Start-up Time ms Output Power Tolerance % 1

2 Protection Functions Output Over Voltage Protection VDC Output Voltage Output Short Circuit Protection A Latch Off Internal Over Temp. Protection (Tc) Maintaining 10% 100 External Over Temp. Protection (Ta) Maintaining 10% 85 Reliability Specifications Life Time Tc= Tc=80 Failure Rate Tc=80 MTBF - 3,000 - Tc=80 Environmental Specifications The life time has been calculated based on Telcordia report. Operation Temperature Ta - - Tc Storage Temperature Ta Humidity % Relative humidity for operation % Relative humidity for storage Standards Parameter Condition Remark Safety Standards EMI / RFI Standards To be designed to meet the requirements as follows ; - UL EN /A1:2011/A2: EN :2014 To be designed to meet the requirements as follows ; - FCC part 15, Class B verification - EN 55015:2006+A1:2007+A2: EN :2006+A1:2009+A2: EN : EN 61547:2009 Protection Type : Manual Resetting Type 2

3 Life Time vs. Case Temperature Curve Power Factor Characteristics 3

4 Efficiency Characteristics 4

5 Dimming Control (1-10V Dimming) 100% Output current vs. Dimming voltage 80% 60% 40% 20% 0% Constant Power Control (Iout vs Vout Curve) Iout [ma] Vout [V] Iout vs NTC Temp. (OTP) Iout [%] External Internal Estimated Temp. [ ] 5

6 Isolation Isolation (V) Mains Input LED Output NTC/Dim Current Selection Metal Housing Mains Input NA LED Output 4000 NA NA NA 4000 NTC/Dim 4000 NA NA NA 4000 Current Selection 4000 NA NA NA 4000 Metal Housing NA Leakage Current Leakage Current < 0.6 MIU The leakage current must be measured again on the luminaire side. Inrush Current Information Ipeak Input Voltage Ipeak 50% of Ipeak 50% of Ipeak 120VAC 6.4A 37.3us 230VAC 13.7A 37.3us 277VAC 19.0A 33.6us Maximum Number of Drivers per MCB Item Max. Number of Drivers (PISE-A040A) Input Voltage [VAC] MCB B type 10A MCB B type 13A MCB B type 16A MCB B type 20A MCB B type 25A

7 Output Current Setting L N Non-Programmable Driver VLED + VLED - Dim+ Comm (DIM-) Rset(Wire A) Rntc 5Vs(Wire B) SGND(Wire C) Wire Connection Output Current RSET 5Vs SGND 700mA Open Open Open 500mA Short Short Open 350mA Short Open Short Functional GND Connection Functional GND is able to be connected with one of four holes which are located in each corner of the metal case. Sawtooth washer is recommended to be used in order to strengthen mechanical contact between the metal case and functional GND. Guidelines for Driver Wire Length Model Output Wires (LED+, LED-) Control Wires (DIM, COMM, NTC, RSET, 5Vs, SGND) PISE-A040A Max. 10 meter Max. 0.5 meter Maximum output cable length is limited by EMI and cross-sectional diameter. All connections must be kept as short as possible to ensure good EMI performance. 7

NTC RSET 5Vs SGND Input WHITE (NEUTRAL) BLACK (LINE) LED Driver RED (VLED+) BLUE (VLED-) VIOLET (DIM+)

8 Mechanical Outline 1. Case Dimension Product Weight : Max. 600g 2. Connector Wiring Diagram Input Cable(18AWG) NEUTRAL LINE Output Cable(18AWG) VLED+ VLED- DIM+ COMM(DIM-) NTC RSET 5Vs SGND Input WHITE (NEUTRAL) BLACK (LINE) LED Driver RED (VLED+) BLUE (VLED-) VIOLET (DIM+) GRAY (COMM) BLK/WHT (NTC) Output LED Array Dimming Wire OTP Housing YELLOW (RSET) VIO/WHT (5Vs) BLU/WHT (SGND) Selectable Output Current Wire 8

9 Datasheet Revision History Change Date Rev. No. Description of Change Remark 2013/11/ Initial Release 2013/12/ /12/ /02/ /05/ /06/ /01/ /04/ Added and revised below information, - Inrush current - LED output voltage range - Output power tolerance - Failure rate / MTBF - Functional GND connection - Input cable : double or reinforced insulation - Isolation table Added and revised below information, - Surge protection level (common and differential mode) - Graphics showing efficiency vs output voltage - Graphic showing Power factor vs output power Output Short Circuit Protection (Page 2) (Remark : Auto Recovery Latch Off) Revised below information, - Failure rate / MTBF Result Added below information, - Leakage current specification - Inrush current information Added below information, - IP level - Product weight - Maximum number of drivers per MCB - Guidelines for driver wire length Added below information, - BIS R Output Safety Certifications Approved - A typing error - Based on the final report 9

Output Power. Parameter Min. Typ. Max. Unit Remark. Parameter Min. Typ. Max. Unit Remark

Output Power. Parameter Min. Typ. Max. Unit Remark. Parameter Min. Typ. Max. Unit Remark PISE-A240A (Pb-Free) 240W Selectable Output Power 180V - 310V / 0.5A - 0.7A - 1.0A / 240W Features Dimmable Type : 1-10 Dimming Input Cable : Double or Reinforced Insulation Mechanical Outline (Metal Case)