Q7055C Building Network Adapters BNA-1C/2CS

Size: px

Start display at page:

Download "Q7055C Building Network Adapters BNA-1C/2CS"

Andra Mitchell
5 years ago
Views:

1 Q0C Building Network Adapters BNA-C/CS INSTALLATION INSTRUCTIONS WARNING This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the Instructions Manual, may cause interference with radio communication. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part or FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case, users at their own expense will be required to take whatever measures may be required to correct the interference. Any unauthorized modification of this equipment may result in the revocation of the owner's authority to continue its operation. GENERAL The Q0C series Building Network Adapters (BNA) provide connection of a Honeywell controller communication bus to an industry standard 0/00BaseT Ethernet. The Building Network Adapter (BNA) delivers exceptional price/ performance to meet the requirements of both building owners and service providers. With its combination of scalable performance, density, and low per-port pricing, the BNA allows network-layer capabilities to be extended to a much wider range of network configurations and environments. High-performance network and services, including traffic management, are now available to additional locations throughout the network. The BNA uses the -connection to provide a seamless communication to the requesting device. Status information such as communication activity, field bus traffic communication, and system Heartbeat of the BNA is indicated by LEDs on the front of the device. The BNA models provide an interface from various Honeywell controller buses that use RS- signals to a local area network using 0. Ethernet protocol. This allows data to be used by high-level Building Management Systems such as the Honeywell Enterprise Buildings Integrator (EBI). This Installation Instruction covers the following BNA devices: Q0C009 BNA-C. Provides a single RS- DC coupled C-Bus-compatible communication channel for Excel 000 family devices with up to. kbps. Q0C0 BNA-CS. Provides two RS- DC coupled C-/S-Bus compatible communication channels for Excel Classic and XL000 family devices in smoke control systems with up to. kbps. Additionally, each BNA is equipped with a RJ- 0/00BaseT connector, plus an RS- interface. (see Fig. ). WORKSTATION BNA-C Fig.. BNA network. The Q0C Building Network Adapter is used in systems for signaling smoke control of fire (UL -9th), UL 9, and general purpose signaling (UL 0). Also applies to CEC. standard. In UL 0 applications, the product can be used as either a type SM (Self-Monitored) or type AM (Attendant-Monitored) system. SPECIFICATIONS EBI ETHERNET LOCAL AREA NETWORK BNA-CS SINGLE C-BUS TWO C-/S-BUS (ONLY FOR XL000, IRC AND EMC (FOR EXCEL IRC, CONTROLLERS FAMILIES) EMC, EXCEL CLASSIC AND XL000 CONTROLLERS FAMILIES) WORKSTATION M0 ls: Q0C009 Building Network Adapter BNA-C. Provides a single RS- DC coupled C-Bus-compatible communication channel for XL00 and Excel 000 family devices with up to. kbps. 9-

2 Q0C0 Building Network Adapter BNA-CS. Provides two RS- DC coupled C-/S-Bus compatible communication channels for Excel Classic, Excel 00, and XL000 family devices. Electrical Ratings: Supply Voltage: VAC, 0 to 0 Hz, or VDC (external power supply required). Power Consumption: BNA-C: VA. BNA-CS: VA. Temperature Ratings: Operating: F to F (0 C to 0 C). Storage: - F to + F (- C to + C). Humidity Ratings: to 9% RH, non-condensing. System Data: Processor: -bit high-speed microprocessor. Data Transfer: 0/00 Mbit/sec., 0. Ethernet. Interface: 0/00BaseT (RJ-). Field Bus (-C/-CS): RS- DC coupled XL000 C-/S-Bus. Device Interface: Serial RS-. Memory: SDRAM, NOR & NAND Flash MTBF: > 00,000 hours. Safety: Protection Standard: IP0 according to EN09. Protection Class: II according to EN00-. Flame Retardant: V0 according to UL 9. Dimensions: -/ in. ( mm) high x -/ in. ( mm) wide x -/ in. (99 mm) deep. Weight:.0 lb. (0.9 kg). Approvals: BNA-C/CS: Electromagnetic Compatibility (EMC): EN00- and EN00-. Electromagnetic Emission (EME): FCC Class A. Energy Management: UL 9 PAZX. Fire Protection and Smoke Control: UL, UUKL; Miscellaneous Signaling UL0 QVAX. Additional Equipment: DC Power Supply: Jameco l No. DDU000, 0 VAC, 0 Hz VA input, VDC, 0.00 Amp output, wall mounted power cube Class (included). AC Power Supply: 0 VAC/0 to 0 Hz input, VAC output, 0 series. Mounting: series communication panels Ditek Ethernet Port Surge Protector. 0-0: Lightning Protector. BEFORE INSTALLATION Perform the following steps prior to installing the BNA device. Verify that the product has been received without damage.. Verify that the correct BNA device has been delivered.. Check the package contents. The following items are included in each product package: Building Network Adapter device Power Supply. Building Network Adapter Installation Instructions. Bag of installation materials as follows: one -pole Phoenix power connector, one or two Phoenix controller bus channel connectors, four optional wall mounting clips, four small inserts and four screws.. Read the Connections section carefully prior to connecting power, ground and data interface cables to the BNA.. Refer to the installation instructions for each component connected to the BNA: Form no. 9-, Excel 00, 00, 00 Series Controller Sub panel Installation Instructions. Form no. 9-, Excel 00/00 Control System Installation Instructions. Form no. 9-, EBI Interface Installation Instructions. Form no. 9-0, EBI Interface Installation Instructions. WIRING CAUTION Shock Hazard. Removal of the BNA cover can result in electrical shock. Do not remove cover. There are no user serviceable parts inside. Location and Mounting The BNA device is intended for installation only indoors in a dry location. It can be mounted in several ways; as a single device, up to three stacked devices, or wall/cabinet mounted. Stacking of BNA devices is not recommended for smoke control applications. Single Device The following illustration shows the single BNA device operating position; for example, on a desk (see Fig ). Fig.. Single Device Operating Position. Stacked Devices BNA devices may also be stacked except in smoke control applications. Because of stability issues, it is recommended not to stack more than three devices (see Fig ). BUILDING NETWORK ADAPTER MODEL CS Reset Power Boot NML There are cooling slots on the top and bottom of the BNA housing. Ch Ch 00 M 9-

3 Place the BNA-adapter with the topside down on the desk. BUILDING NETWORK ADAPTER MODEL CS Reset Power Boot NML Ch Ch Ch Ch Remove the four feet from the bottom of the BNA by pushing horizontally away from the housing with a flat screwdrive r. 00 Ch Ch BUILDING NETWORK ADAPTER MODEL CS Reset Power Boot NML Ch Ch 00 Push the four inserts (included) fully and horizontally into the housing. 00 Ch Ch BUILDING NETWORK ADAPTER MODEL CS Adjust the four retaining clips (included) on top of the inserts. Fasten the retaining clips with the included four screws. Reset Power Boot NML Ch Ch Ch Ch Fig.. Stacked Devices. M Wall Mounting It is also possible to mount the BNA device to a wall. The following sequence describes how the device should be prepared prior to mounting it on a wall (see Fig ). 00 Ch Ch Use the housing with the clips to mark the positions of the four mounting holes on the wall surface. Drill / in. ( mm) holes for the mounting screws (not included) and fix the BNA device. Fig.. BNA wall mount. MA Table. C-Bus Connector Terminal Specifications. Communications Panel Mounting It is also possible to mount the BNA device in the series Communications Panel (see Fig. ). This method of mounting is recommended for smoke control applications. Connector Terminal Pin Signal Type Input/ Output Voltage Type Max. Voltage Max. Current Max. Frequency Max.Line Impedance CH/CH RS- (C-BUS)* CH/CH RS- (C-BUS)* A(+) +In Input/Output SIGNAL ± V ma/ 0 ma 900 baud 00 ohms B(-) -In Input/Output SIGNAL ± V ma/ 0 ma 900 baud 00 ohms * supervised spaces Max wiring distance,000 ft. (,9m), AWG min. 9-

4 WIRE PER NEC FOR FIRE ALARM H N G BNA NON-POWER LIMITED AREA POWER LIMITED AREA TYPICAL MOUNTING LOCATION FOR Q0 BUILDING NETWORK ADAPTER (BNA). G = GROUNDING CONDUCTOR MOV FACTORY INSTALLED ON TERMINAL STRIP. GROUND CONNECTION. - STUD WITH - KEPS NUT. GROUND CONNECTION FOR 0 SERIES ETHERNET PROTECTOR AND OTHER LOW VOLTAGE EQUIPMENT. DRILLED MOUNTING HOLES FOR PORT ETHERNET HUB (IF USED). SYSTEM WIRING IS CLASSIFIED AS EITHER POWER LIMITED OR NON-POWER LIMITED PER NEC ARTICLE 0. ALL POWER LIMITED WIRING MUST BE SEPARATED FROM ALL NON-POWER LIMITED WIRING BY A MINIMUM DISTANCE OF / IN. ( MM). M Fig.. Typical mounting of Q0C BNA Assembly on series Communications Panel. 9-

5 CONNECTIONS This section describes how to connect power and the field bus to the BNA device. A supply pack with installation material containing the required connectors for power and the field bus are shipped with the device. CABLES AND CONNECTORS DB9F Null m Connector Fig. illustrates a serial connector for the field bus. Fig. shows how to configure a Null m Cable DB9F. Power Connection The BNA device requires a UL listed external power supply with the following specifications: VAC, 0 to 0 Hz, or VDC. Typical power supplies include: DC Power Supply: Jameco l No. DDU000, 0 VAC, 0 Hz VA input, VDC, 0.00 Amp output, wall mounted power cube Class (included). AC Power Supply: 0 VAC/0 to 0 Hz input, VAC output, 0 series. Power consumption of the BNA device is VA. For the power connection, the -pole Phoenix connector is required (included). Wire the power cable as follows:. Cut off the original connector at the end of the cable. In case of a DIN connector equipped power cable, identify the VDC cable pair using a multimeter. If the power supply has screw terminals, wire a cable to the V and GND terminals on the power supply.. Strip the two power cable ends and insert each cable end into the openings of the -pole Phoenix connectors that are marked for power.. Fasten them with a screwdriver.. Connect a chassis ground to the third position on this connector as marked. = DCD = RxD = TxD = DTR = GROUND 9 = RI = CTS = RTS = DSR M99 Fig.. Serial connector (female connector is numbered as shown). RxD RxD The polarity (+/-) of the -pole Phoenix power connector for DC power supplies is don't care. TxD TxD Field Bus Connection (Ch/Ch) For connecting the field bus, the -pole or -pole Phoenix connectors (included) are required. Field bus connection can be configured only as class B/style. All field wiring is supervised. Consult form no. -0, Q0C Building Network Adapter BNA-C/CS Checkout & Test for additional information on field bus wiring. DTR DCD DSR GND RTS DSR DCD DTR GND RTS CTS CTS RI 9 9 RI M99 Fig.. Signal connections for DB9F Null m Cable. 9-

6 Ethernet Connection See Fig. for BNA Ethernet connection. Tx + Tx + Tx - Tx - Rx + Rx + -PIN MODULAR CONNECTOR RJ- Rx - Rx - M99 Fig.. BNA Ethernet connector. M99 RJ- Connector The BNA provides a standard RJ- connector for 0/ 00BaseT Ethernet connection. This section describes the pin layout for the RJ- connector. Most Ethernet local area networks use twisted pair wiring. 0/00BaseT networks are physically laid out in a star topology, where each piece of equipment on the network is connected to a central hub. The wiring is connected to devices using a plug that resembles a phone jack called RJ-. See Table for RJ- signals. Fig. 9. Straight-through pinning for BNA to EthernetHub connections. Connect BNA to Workstation When a BNA needs a direct connection to a workstation without using an Ethernet Hub, a crossover cable is required. Fig.0 shows how the different signals should be connected. Table. RJ- Signals. Pin Number Signal Name Transmit (TX) + Transmit (TX) Tx + Tx - Rx + Tx + Tx - Rx + Receive (RX) + Rx - Rx - Reserved Reserved Receive (RX) Reserved Reserved M99 Connect BNA to HUB To connect a BNA device to a via an Ethernet Hub, the required cable should be configured as shown in Fig. 9. Fig. 0. Crossover pinning for BNA to workstation, direct connections. COMMISSIONING Finish the installation by commissioning the BNA in accordance with form no. -0, Q0C Building Network Adapter BNA-C/CS Checkout & Test. 9-

7 OPERATION Location of Parts and Controls Refer to Figures and and the following descriptions for the location and function of parts and controls. 0LNK. Ethernet speed of 0 mbps indicator (Green). If this LED is lit, then the Ethernet link is operating at 0 mbps. 00LNK. Ethernet speed of 00 mbps indicator (Green). If this LED is lit, then the Ethernet link is operating at 00 mbps. Activity. Link activity indicator (Green) will blink if there is any activity (transmission/reception) on the. BUILDING NETWORK ADAPTER MODEL CS BNA-CS Reset Power Boot NML Ch Ch 0 00 ACT normal Ch normal Ch A(+) B(-) A(+) B(-) MA AC/DC IN V + - 0/00 Fig.. Parts and controls on front side of BNA. RESET Hardware reset button. Located directly behind the small hole in the front panel. To reach this button, a pointed object like a sharp pen or an unfolded paper clip is necessary. Pressing this button resets the BNA device immediately. This operation is similar to applying power to the BNA device. The sequence of operations following the RESET is similar to Power on BNA device. POWER Power indicator. This LED lights up when power is connected to the BNA device. HEARTBEAT System Heartbeat display consists of two LEDs, one Red and one Green. During BNA system startup when BIOS is running, both LEDs flash continuously. When BNA Bootloader starts to run, the Red LED starts to flash. When the application firmware begins to run, the Green LED starts flashing. CH Bus Channel activity display. This display contains two green LEDs; one showing the BNA receive activity (Rx), and the other showing the BNA transmit activity (Tx). CH Bus Channel activity display. This display contains two green LEDs; one showing the BNA receive activity (Rx), and the other showing the BNA transmit activity (Tx). Ch indication is only available on two channel devices. It is not available on the BNA-C. MODE switch button. This button is used to change the operating modes. For a detailed description about BNA operation modes, refer to the Operating s section of form no. -0, Q0C Building Network Adapter BNA- C/CS Checkout & Test. Local Area Network () activity display. Shows the actual traffic status using three LEDs: Fig.. Parts and controls on rear side of BNA. CH -pin connector for field bus channel connection, electrically isolated, meets EMC and FCC requirements. Field Bus wiring is described in the Field Bus Connection (Ch/Ch) section. The Ch field bus connector is only available on twochannel devices. It is not available on the BNA-C. 9 CH/CH BUS TERMINATION SWITCHES These switches are used to select field bus termination and biasing. For a detailed description of the bus termination switch positions, refer to the Bus Termination Switch section of form no. -0, Q0C Building Network Adapter BNA- C/CS Checkout & Test. 0 9 M The Bus Termination Switch option near the Ch field bus connector is only available on BNA-CS two-channel devices. It is not available on the BNA- C. 0 CH -pin connector for field bus channel connection, electrically isolated, meets EMC and FCC requirements. Field Bus wiring is described in the Field Bus Connection (Ch/Ch) section. AC/DC IN V Power connector for VAC (0 Hz to 0 Hz) or VDC power supplies and chassis ground. An external power supply is required. See the Power Connection section of this document for details. RS- 9-pin SUB-D male RS- connector, electrically isolated, PC pin compatible, protected against spikes. This interface is used for initial device setup and requires a standard Null- m cable when interfacing to a PC. 9-

8 0/00BASET 0/00BaseT RJ- Ethernet -connector, meets the requirements of ANSI/TIA/EIA Category, for unshielded twisted pair connections. MAINTENANCE PROCEDURES The system must be maintained in accordance with the system documentation and procedures and practices contained in applicable NFPA and UL standards. The Q0C BNA has no user replaceable fuses. For service, contact your local Honeywell Automation & Control Solutions office as listed in the phone book, or contact a regional office as shown at the end of this document. Jameco IS A REGISTERED TRADEMARK OF ARNDT ELECTRONICS ELPAC IS A REGISTERED TRADEMARK OF JSR CORPORATION. HONEYWELL EXCEL 000 AND DELTANET ARE REGISTERED TRADEMARKS AND ENTERPRISE BUILDINGS INTEGRATOR IS A TRADEMARK OF HONEYWELL INC. 9-

9 9 9-

10 Automation and Control Solutions In Pacific Honeywell Pacific Level, Richardson Place North Ryde, NSW In North America Honeywell International Inc. 9 Douglas Drive North Golden Valley, MN In Asia Zhang Jiang Hi-Tech Park No. 0, Li Bing Rd, Pudong New Area Shangai, 00, China In Europe, Middle East, Africa & India Hermes Plaza Hermeslaan, H B-, Diegem, Belgium U.S. Registered Trademark 009 Honeywell International Inc. 9- Rev. 0-09

Q7055B Building Network Adapters BNA-1C/2CS/2DN

Q7055B Building Network Adapters BNA-1C/2CS/2DN Q0B Building Network Adapters BNA-C/CS/DN INSTALLATION INSTRUCTIONS WARNING This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the Instructions