ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for VMware ESX

Transcription

1

2

3 Preface This document briefly explains the operations that need to be performed by the user in order to connect an ETERNUS2000 model 100 or 200, ETERNUS4000 model 300, 400, 500, or 600, or ETERNUS8000 model 700, 800, 900, 1100, 1200, 2100, or 2200 Disk storage system to a PRIMERGY or PRIMEQUEST 1000 series running VMware ESX via a Fibre Channel interface. This document should be used in conjunction with any other applicable user manuals, such as those for the ETERNUS2000 model 100 or 200, ETERNUS4000 model 300, 400, 500, or 600, or ETERNUS8000 model 700, 800, 900, 1100, 1200, 2100, or 2200 Disk storage system, server, OS, Fibre Channel cards, drivers, etc. This document references the following documents: Server Support Matrix ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for VMware ESX Also note that in this document the ETERNUS2000 models 100 and 200, ETERNUS4000 models 300, 400, 500, and 600, and ETERNUS8000 models 700, 800, 900, 1100, 1200, 2100, and 2200 Disk storage systems are collectively referred to as ETERNUS Disk storage systems. Sixth Edition December 2010 The Contents and Structure of this Manual This document is composed of the following three chapters and an appendix. Chapter 1 Workflow This describes how to set up the server and Fujitsu Fibre Channel card driver when connecting the ETERNUS Disk storage systems to the server via Fujitsu Fibre Channel cards. Chapter 2 For PRIMERGY This describes how to install and set up the Fibre Channel cards and server. Chapter 3 For PRIMEQUEST 1000 Series This describes how to install and set up the Fibre Channel cards and server. A WWN instance management table for the server which is used when checking the Fibre Channel cards is described in the appendix. 3

4 Preface Safe Use of this Product Using this manual This manual contains important information to ensure the safe use of this product. Be sure to thoroughly read and understand its contents before using the product. After reading, store this manual in a safe place for future reference. FUJITSU has made every effort to ensure the safety of the users and other personnel, and to prevent property damage. When using this product, carefully follow the instructions described in this manual. Acknowledgments VMware, VMware logos, Virtual SMP, and VMotion are either registered trademarks or trademarks of VMware, Inc. in the U.S. and/or other countries. Emulex is a trademark of Emulex Corp. QLogic is a trademark of QLogic Corp. The company names, product names and service names mentioned in this document are registered trademarks or trademarks of their respective companies. 4

5 Preface Naming Conventions Product names "VMware ESX" represents the following products: - VMware vsphere (ESX 4.1, ESXi 4.1, ESX 4.0, ESXi 4.0) - VMware Infrastructure 3 (ESX 3.5, ESXi 3.5) - VMware ESX Server 2.5.x Other names "Channel Adapter" (CA) refers to a Fibre Channel interface module used in the ETERNUS Disk storage systems to connect to the server. "Fibre Channel card" refers to the Fibre Channel interface module normally used in the server. A "Host Bus Adapter" (HBA) or "Channel Adapter" (CA) may be used instead, depending on the server. "VMware ESX" refers to "VMware vsphere", "VMware Infrastructure 3", and "VMware ESX Server 2.5.x", which are datacenter solutions from VMware that virtualize the storage and networking system. The name "VMware vsphere", "VMware Infrastructure 3", and "VMware ESX Server 2.5.x" are used in specific datacenter sections. Italics are used to show variables such as values and characters that appear in command parameters and output examples. Screen shot(s) reprinted with permission from Microsoft Corporation. 5

6 Contents Chapter 1 Workflow...7 Chapter 2 For PRIMERGY Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards Setting Up the Fibre Channel Card Setting Up SAN Boot Installing the VMware ESX Server Setting Up the Fibre Channel Card Driver Setup Procedure for S26361-F3023-E1 Fibre Channel Cards Setting Up the Fibre Channel Card Setting Up SAN Boot Setting the Selectable Boot Installing the VMware ESX Server Setting Up the Fibre Channel Card BIOS Setting Up the Fibre Channel Card Driver Chapter 3 For PRIMEQUEST 1000 Series Setup Procedure for MC-0JFC11 or MC-0JFC21 Fibre Channel Cards Setting Up the Fibre Channel Card Setting SAN Boot Installing the VMware ESX Server Setting Up the Fibre Channel Card Driver Appendix A WWN Instance Management Table for the Server (Blank)

7 Chapter 1 Workflow This manual describes how to install and set up Fibre Channel cards when a PRIMERGY or PRIMEQUEST 1000 series is used. Workflow Set Up the Fibre Channel Cards Install the Fibre Channel cards, acquire their physical addresses and WWN information, and perform the BIOS settings. Refer - For S26361-F2843-E1/S26361-F2843-E201, S26361-F3141-E10/S26361-F3141- E210, S26361-F3141-E1, S26361-F3306-E1/S26361-F3306-E201, S26361-F3961- E1/S26361-F3961-E201, S26361-F3961-E2/S26361-F3961-E202, S26361-F3306- E601, and MC-FC82E Fibre Channel cards "2.1.1 Setting Up the Fibre Channel Card" (page 9) - For S26361-F3023-E1 Fibre Channel cards "2.2.1 Setting Up the Fibre Channel Card" (page 21) - For MC-0JFC11 or MC-0JFC21 Fibre Channel cards "3.1.1 Setting Up the Fibre Channel Card" (page 34) Set Up SAN Booting Set up the SAN Boot configuration (if SAN Boot is to be used). Refer - For S26361-F2843-E1/S26361-F2843-E201, S26361-F3141-E10/S26361-F3141- E210, S26361-F3141-E1, S26361-F3306-E1/S26361-F3306-E201, S26361-F3961- E1/S26361-F3961-E201, S26361-F3961-E2/S26361-F3961-E202, S26361-F3306- E601, and MC-FC82E Fibre Channel cards "2.1.2 Setting Up SAN Boot" (page 11) - For S26361-F3023-E1 Fibre Channel cards "2.2.2 Setting Up SAN Boot" (page 26) - For MC-0JFC11 or MC-0JFC21 Fibre Channel cards "3.1.2 Setting SAN Boot" (page 36) 7

8 Chapter 1 Workflow > Install the VMware ESX Install the VMware ESX software. Refer - For S26361-F2843-E1/S26361-F2843-E201, S26361-F3141-E10/S26361-F3141- E210, S26361-F3141-E1, S26361-F3306-E1/S26361-F3306-E201, S26361-F3961- E1/S26361-F3961-E201, S26361-F3961-E2/S26361-F3961-E202, S26361-F3306- E601, and MC-FC82E Fibre Channel cards "2.1.3 Installing the VMware ESX Server" (page 17) - For S26361-F3023-E1 Fibre Channel cards "2.2.4 Installing the VMware ESX Server" (page 30) - For MC-0JFC11 or MC-0JFC21 Fibre Channel cards "3.1.3 Installing the VMware ESX Server" (page 36) Set Up the Fibre Channel Card Driver Set up the parameters for the Fibre Channel card driver. Refer - For S26361-F2843-E1/S26361-F2843-E201, S26361-F3141-E10/S26361-F3141- E210, S26361-F3141-E1, S26361-F3306-E1/S26361-F3306-E201, S26361-F3961- E1/S26361-F3961-E201, S26361-F3961-E2/S26361-F3961-E202, S26361-F3306- E601, and MC-FC82E Fibre Channel cards "2.1.4 Setting Up the Fibre Channel Card Driver" (page 17) - For S26361-F3023-E1 Fibre Channel cards "2.2.6 Setting Up the Fibre Channel Card Driver" (page 32) - For MC-0JFC11 or MC-0JFC21 Fibre Channel cards "3.1.4 Setting Up the Fibre Channel Card Driver" (page 37) After completing all the required procedures in this manual, proceed to "Check the LUNs" in "ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for VMware ESX". 8

9 Chapter 2 For PRIMERGY 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards This section describes how to set up the VMware ESX server for use with the S26361-F2843-E1/ S26361-F2843-E201, S26361-F3141-E10/S26361-F3141-E210, S26361-F3141-E1, S F3306-E1/S26361-F3306-E201, S26361-F3961-E1/S26361-F3961-E201, S26361-F3961-E2/ S26361-F3961-E202, S26361-F3306-E601, or MC-FC82E Fibre Channel card. When the S26361-F3023-E1 Fibre Channel card is used, follow the procedure in "2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards" (page 21). Depending on the Fibre Channel card used, the actual on-screen Fibre Channel card information may differ from that in the screenshots shown in this document Setting Up the Fibre Channel Card Install the Fibre Channel card to the server and acquire its physical address and WWN (World Wide Name). Physical address and Fibre Channel card WWN are required information in the cases shown as follows; when an error has occurred in the system, when using the ETERNUS Disk storage systems' host affinity function, etc., to restrict server access, or when connecting the ETERNUS Disk storage systems and the server using Fibre Channel switch. The relationship between a physical address and WWN cannot be determined from the BIOS. The physical address and WWN must be recorded as a pair when each Fibre Channel card is installed. Physical address and WWN must be assigned to "WWN instance management table for the server". The procedures are described below: (1) Install the Fibre Channel card (2) Turn on the server (3) Acquire the physical address and WWN for the Fibre Channel card (4) Add a record for the server in the WWN instance management table for the server 9

10 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards The following describes the procedure: Procedure 1 Install the Fibre Channel card to the server. For the installation method, slot positions and notes regarding the Fibre Channel card, refer to the manual provided with the Fibre Channel card or the User Guide of the server. 2 Turn on the server, and press the [Alt] + [E] keys while the following message is displayed. Light Pulse BIOS Utility starts. Example:!!! BX600-FC42E BIOS, Copyright(C) 2005 Emulex!!! Version xxxxxx Press <Alt E> to go to Emulex BIOS Utility. Press <s> to skip Emulex BIOS 3 Enter the number of the Fibre Channel card to be checked and press the [Enter] key. Example: Emulex Light Pulse BIOS Utility, ZBXXXXXX Copyright(C) 2005 Emulex Design & Manufacturing Corp Emulex Adapters in the System; 1. BX600-FC42E PCI Bus #:xx PCI Device #:00 2. BX600-FC42E PCI Bus #:xx PCI Device #:00 Enter a Selection: Enter <x> to Exit <d> to Default Values <Esc> to Previous Menu 4 Check the [I/O Base] and [Port Name] values. The value of [I/O Base] is the physical address and the value of [Port Name] is WWN. Example: Adapter 0x: PCI Bus#:xx PCI Device#:00 BX600-FC42E I/O Base: xxxx Firmware Version: ZS2.70A5 Port Name: xxxxxxxx Node Name: xxxxxxxx Topology: Fabric Point to Point 1.Configure Boot Devices. 2.Configure This Adapter s Parameters. Enter a Selection: Enter <x> to Exit <d> to Default Values <Esc> to Previous Menu 10

11 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards 5 Record the physical address and WWN in the "WWN instance management table for the server". This table is provided in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 39). The following shows an example of this. Host name Server#1 IP Address Physical slot name Fibre Channel card WWN Instance name Physical address Cable tag slot C9 38 D SERV1_SLOT0 to SN200_1_port0 Details of contents Host name: IP Address: Physical slot name: Fibre Channel card WWN: Instance name: Physical address: Cable tag: Record the host name. Record the IP address of the server. Record the slot position of installed Fibre Channel card. Record the value of [Port Name]. Not necessary to record. Record the value of [I/O Base]. Record a tag name which indicates the connection path (relationship between the connected device and the port). 6 Press the [X] key to quit the Light Pulse BIOS Utility. When the total number of ports for installed Fibre Channel cards is two or more, first turn the server off, then repeat Step 1 through Step 6 above for each port, and record the information for all ports in the "WWN instance management table for the server". End of procedure Setting Up SAN Boot The following describes the procedure when performing SAN Boot. Depending on the Fibre Channel card used, the actual on-screen Fibre Channel card information may differ from that in the screenshots shown in this document. 11

12 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards Procedure 1 Turn on the server, and press the [Alt] + [E] keys while the following message is displayed.!!! BX600-FC42E BIOS, Copyright(C) 2005 Emulex!!! Version xxxxxx Press <Alt E> to go to Emulex BIOS Utility. Press <s> to skip Emulex BIOS 2 Enter the number of the Fibre Channel card for which SAN Boot is to be set and press the [Enter] key. Emulex Light Pulse BIOS Utility, ZBXXXXXX Copyright(C) 2005 Emulex Design & Manufacturing Corp Emulex Adapters in the System; 1. BX600-FC42E PCI Bus #:xx PCI Device #:00 2. BX600-FC42E PCI Bus #:xx PCI Device #:00 Enter a Selection: Enter <x> to Exit <d> to Default Values <Esc> to Previous Menu 3 Select "2. Configure This Adapter s Parameters" and press the [Enter] key. Adapter 0x: PCI Bus #:xx PCI Device#:00 BX600-FC42E I/O Base:xxxx Firmware Version: ZS2.70A5 Port Name: xxxxxxxx Node Name: xxxxxxxx Topology: Fabric Point to Point 1. Configure Boot Devices. 2. Configure This Adapter s Parameters. Enter a Selection: Enter <x> to Exit <d> to Default Values <Esc> to Previous Menu 4 Select "1. Enable or Disable BIOS" and press the [Enter] key. Adapter 0x: PCI Bus #:xx PCI Device#:00 BX600-FC42E I/O Base:xxxx Firmware Version: ZS2.70A5 Port Name: xxxxxxxx Node Name: xxxxxxxx Topology: fabric Point to Point 1. Enable or Disable BIOS. 2. Change Default ALPA of this Adapter. 3. Change PLOGI Retry Timer (+Advanced Option+) 4. Topology Selection (+Advanced Option+) 5. Enable or Disable Spinup delay (+Advanced Option+) 6. Auto Scan Setting (+Advanced Option+) 7. Enable or Disable EDD 3.0 (+Advanced Option+) 8. Enable or Disable Start Unit Command (+Advanced Option+) 9. Enable or Disable Environment Variable (+Advanced Option+) A. Auto Sector Format Select (+Advanced Option+) Enter a Selection: Enter <x> to Exit <Esc> to Previous Menu 12

13 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards 5 Input "1" and press the [Enter] key. Adapter 0x: PCI Bus #:xx PCI Device#:00 The BIOS is Disabled! Enable Press 1, Disable Press 2: Enter <x> to Exit <Esc> to Previous Menu BIOS is now enabled. "The BIOS is Disabled!" should have changed to "The BIOS is Enabled!". Adapter 0x: PCI Bus #:xx PCI Device#:00 The BIOS is Enabled! Enable Press 1, Disable Press 2: Enter <x> to Exit <Esc> to Previous Menu 6 Press the [ESC] key to return to the window shown in Step 4. 7 Select "4. Topology Selection" and press the [Enter] key. 8 Select either "1. Auto Topology: Loop first (Default)" (for FC-AL connection), or "4. Fabric Point to Point" (for fabric connection), and press the [Enter] key. Adapter 0X: PCI Bus #:xx PCI Device#:00 Topology: Fabric point to Point 1. Auto Topology: Loop first (Default) 2. Auto Topology: Pt to Pt first 3. FC-AL 4. Fabric Point to Point Enter a Selection: Enter <x> to Exit <Esc> to Previous Menu 9 Press the [ESC] key to return to the window shown in Step Select "6. Auto Scan Setting" and press the [Enter] key. 13

14 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards 11 Displays the changed Auto scan setting of the boot device. Input the number (1 to 4) of the desired Auto scan setting after "Enter a Selection:" and press the [Enter] key. Adapter 0X: PCI Bus #:xx PCI Device#:00 Auto scan setting: First LUN 0 device. 1. Auto scan disabled (Default) 2. Any first device. 3. First LUN 0 device. 4. First NOT LUN 0 device. Enter a Selection: Enter <x> to Exit <Esc> to Previous Menu 12 Press the [X] key to quit the Light Pulse BIOS Utility. 13 Input "Y" after "REBOOT THE SYSTEM(Y/N):" to boot the server to reflect the new setting. Reboot the System to Make All the Changes to Take Effect! REBOOT THE SYSTEM(Y/N):_ 14 Press the [Alt] + [E] keys while the startup message is displayed.!!!!!!bx600-fc42e Emulex LPxxxx BIOS, Copyright(c) !!! Emulex xxxxxxxx!!! Version xxxxxx Press Press <Alt <Alt E> to E> go to to go Emulex to Emulex BIOS BIOS Utility. Press Press <s> <s> to skip to skip Emulex Emulex BIOS. BIOS 15 Input the number of the Fibre Channel card selected in Step 2 after "Enter a Selection:" and press the [Enter] key. Emulex Light Pulse BIOS Utility, ZBxxxxxx Copyright(c) 2005 Emulex Design & Manufacturing Corp Emulex Adapters in the System; 1. BX600-FC42E PCI Bus #:xx PCI Device #:00 2. BX600-FC42E PCI Bus #:xx PCI Device #:00 Enter a Selection: Enter <x> to Exit <d> to Default Values <Esc> to Previous Menu 14

15 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards 16 Select "1. Configure Boot Devices" and press the [Enter] key. Adapter 0x: PCI Bus #:xx PCI Device#:00 BX600-FC42E I/O Base:xxxx Firmware Version: ZS2.70A5 Port Name: xxxxxxxx Node Name: xxxxxxxx Topology: Fabric point to Point 1. Configure Boot Devices. 2. Configure This Adapter s Parameters. Enter a Selection: Enter <x> to Exit <d> to Default Values <Esc> to Previous Menu From Step 17 onward, the examples assume the use of LUN00 and the device name "ETERNUS8000" for the Primary Boot device. 17 Select a boot device. Input "1" after "Select a Boot Entry:" and press the [Enter] key. Adapter 0x: S_ID: xxxxxx PCI Bus #:xx PCI Device#:00 List of Saved Boot Devices: 1. Unused DID: WWPN: LUN:00 Primary Boot 2. Unused DID: WWPN: LUN:00 3. Unused DID: WWPN: LUN:00 4. Unused DID: WWPN: LUN:00 5. Unused DID: WWPN: LUN:00 6. Unused DID: WWPN: LUN:00 7. Unused DID: WWPN: LUN:00 8. Unused DID: WWPN: LUN:00 Select a Boot Entry: Enter <x> to Exit <Esc> to Previous Menu 18 A list of the WWPNs and recognized LUNs (as device names) of the connected ETERNUS8000 is displayed. Input the number of the device that is to be used for SAN Booting and press the [Enter] key. Select "01" in this example. Adapter 0x: S_ID :xxxxxx PCI Bus #:xx PCI Device#: Clear Selected Boot Entry!! 01. DID:xxxxxx WWPN: B 5D6A0336 LUN:00 FUJITSU E DID:xxxxxx WWPN: B 5D6A0336 LUN:0x FUJITSU E Select the Two Digit Number of The Desired Boot Device:01 Enter <x> to Exit <Esc> to Previous Menu <PageDn> to Next Page 15

16 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards 19 Input the starting LUN as a two-digit hexadecimal number and press the [Enter] key. Input "00" in this example. Adapter 0x: S_ID :xxxxxx PCI Bus #:xx PCI Device#: Clear Selected Boot Entry!! 01. DID:xxxxxx WWPN: B 5D6A0336 LUN:00 FUJITSU E DID:xxxxxx WWPN: B 5D6A0336 LUN:0x FUJITSU E DID: xxxxxx WWPN: xxxxxxxx xxxxxxxx Enter two digits of starting LUN(Hex):00 <Esc> to Previous Menu Select the Two Digit Number of The Desired Boot Device: Enter <x> to Exit <Esc> to Previous Menu <PageDn> to Next Page 20 Select a boot device startup method (via WWPN or via DID). From the list of LUNs recognized by the device select the LUN number whose setting is to be changed, input the number after "Enter a Selection:" and press the [Enter] key. LUN: 00 is used for SAN Booting, so input "01" and press the [Enter] key in this example. Adapter 0x: S_ID: xxxxxx PCI Bus #:xx PCI Device#:00 DID: xxxxxx WWPN:xxxxxxxx xxxxxxxx 01. LUN:00 FUJITSU E LUN:01 FUJITSU E Enter a Selection:01 B#W: Boot number via WWPN. B#D: Boot number via DID Enter <x> to Exit <Esc> to Previous Menu <PageDn> to Next Page 21 In the sub-menu that is displayed in the center of the window decide whether the boot is to be via WWPN or via DID for the selected LUN, input the number of the selected method after "Enter a Selection:" and press the [Enter] key. Input "1" for WWPN in this example. Adapter 0x: S_ID: xxxxxx PCI Bus #:xx PCI Device#:00 DID: xxxxxx WWPN:xxxxxxxx xxxxxxxx 01. LUN:00 FUJITSU E LUN:00 FUJITSU E DID: xxxxxx WWPN: xxxxxxxx xxxxxxxx LUN: 0x 1.Boot this device via WWPN 2.Boot this device via DID <Esc> to Precious Menu Enter a Selection:1 Enter a Selection: B#W: Boot number via WWPN, B#D: Boot number via DID Enter <x> to Exit <Esc> to Previous Menu <PageDn> to Next Page 16

17 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards 22 The window shown in Step 17 reappears. Check the settings. In this example, check that item #1 is listed as "Used", that the "WWPN" is set to the actual ETERNUS8000 WWPN, and that the "LUN" is set to "00" and that it bears the "Primary Boot" label. Adapter 0x: S_ID: xxxxxx PCI Bus #:xx PCI Device#:00 List of Saved Boot Devices: 1. Used DID: WWPN:xxxx xxxx xxxx xxxx LUN:00 Primary Boot 2. Unused DID: WWPN: LUN:00 3. Unused DID: WWPN: LUN:00 4. Unused DID: WWPN: LUN:00 5. Unused DID: WWPN: LUN:00 6. Unused DID: WWPN: LUN:00 7. Unused DID: WWPN: LUN:00 8. Unused DID: WWPN: LUN:00 Select a Boot Entry: Enter <x> to Exit <Esc> to Previous Menu 23 Press the [Esc] key twice to return to the window shown in Step 2. If multiple Fibre Channel cards are to be installed, repeat Step 2 through Step 23 for each card. 24 Press the [X] key to quit the Light Pulse BIOS Utility. End of procedure Installing the VMware ESX Server VMware ESX should be installed now if it has not yet been installed on the server. Refer to the following URL for details Setting Up the Fibre Channel Card Driver To connect to the ETERNUS2000, change the parameters for the Fibre Channel card driver. When connecting to the ETERNUS4000 or ETERNUS8000, the parameters for the Fibre Channel card driver do not have to be changed because the default values of the standard driver for VMware ESX are used. 17

18 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards For VMware vsphere F Procedure 1 Record the module name for the Fibre Channel card that is loaded into VMware ESX. In the following example, "lpfc820" is recorded as the module name. # vmkload_mod -l grep lpfc* lpfc820 Loaded module name Module names may vary depending on the Fibre Channel card that is used. 2 Check the default value for the Fibre Channel card. Specify the module name for the Fibre Channel card that you recorded in Step 1 and check the default value. # esxcfg-module -g lpfc820 lpfc820 enabled = 1 options = '' Check that no value appears. 3 Check the number of ports on the Fibre Channel card. The SCSI Host numbers of the Fibre Channel card that are displayed represent the number of ports. In the following example, the number of ports is "two" since "4" and "5" (two numbers) are displayed as the SCSI Host numbers of the Fibre Channel card. # ls /proc/scsi/lpfc 4 5 The number of ports is "two". 4 Change the setting values of the parameter for the Fibre Channel card driver. Driver parameter Number of I/Os when 16 or less LUNs are used Driver parameter setting values Number of I/Os when 17 or more LUNs are used lpfcx_lun_queue_depth 8 4 Use the following command to change the setting values when the driver parameter name is "lpfcx_lun_queue_depth", the number of I/Os is "8", the module name is "lpfc820", and the number of ports is "2". # esxcfg-module -s "lpfc0_lun_queue_depth=8 lpfc1_lun_queue_depth=8" lpfc820 Input the number of I/Os ("8" in this example) for each driver parameter setting. 18

19 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards 5 Check the setting values. # esxcfg-module -g lpfc820 lpfc820 enabled = 1 options = 'lpfc0_lun_queue_depth=8 lpfc1_lun_queue_depth=8' 6 Reboot VMware ESX. # reboot End of procedure For VMware Infrastructure 3 Procedure 1 Record the module name for the Fibre Channel card that is loaded into VMware ESX. In the following example, "lpfc_740" is recorded as the module name. # vmkload_mod -l grep lpfc* lpfc_740 Loaded module name Module names may vary depending on the Fibre Channel card that is used. 2 Check the default value for the Fibre Channel card. Specify the module name for the Fibre Channel card that you recorded in Step 1 and check the default value. # esxcfg-module -g lpfc_740 lpfc_740 enabled = 1 options = '' Check that no value appears. 3 Check the number of ports on the Fibre Channel card. The SCSI Host numbers of the Fibre Channel card that are displayed represent the number of ports. In the following example, the number of ports is "two" since "4" and "5" (two numbers) are displayed as the SCSI Host numbers of the Fibre Channel card. # ls /proc/scsi/lpfc 4 5 The number of ports is "two". 19

20 > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards 4 Change the setting values of the parameter for the Fibre Channel card driver. Driver parameter Number of I/Os when 16 or less LUNs are used Driver parameter setting values Number of I/Os when 17 or more LUNs are used lpfcx_lun_queue_depth 8 4 Use the following command to change the setting values when the driver parameter name is "lpfcx_lun_queue_depth", the number of I/Os is "8", the module name is "lpfc_740", and the number of ports is "2". # esxcfg-module -s "lpfc0_lun_queue_depth=8 lpfc1_lun_queue_depth=8" lpfc_740 Input the number of I/Os ("8" in this example) for each driver parameter setting. 5 Check the setting values. # esxcfg-module -g lpfc_740 lpfc_740 enabled = 1 options = 'lpfc0_lun_queue_depth=8 lpfc1_lun_queue_depth=8' 6 Update the loaded module. # esxcfg-boot -b 7 Reboot VMware ESX. # reboot End of procedure 20

21 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards This section describes how to set up the VMware ESX server for use with the S26361-F3023-E1 Fibre Channel card. When the S26361-F2843-E1/S26361-F2843-E201, S26361-F3141-E10/S26361-F3141-E210, S26361-F3141-E1, S26361-F3306-E1/S26361-F3306-E201, S26361-F3961-E1/S26361-F3961- E201, S26361-F3961-E2/S26361-F3961-E202, S26361-F3306-E601, or MC-FC82E Fibre Channel card is used, follow the procedure in "2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards" (page 9). Depending on the Fibre Channel card used, the actual on-screen Fibre Channel card information may differ from that in the screenshots shown in this document Setting Up the Fibre Channel Card Install the Fibre Channel card to the server and acquire its physical address and WWN (World Wide Name). Physical address and Fibre Channel card WWN are required information in the cases shown as follows; when an error has occurred in the system, when using the ETERNUS Disk storage systems' host affinity function, etc., to restrict server access, or when connecting the ETERNUS Disk storage systems and the server using Fibre Channel switch. The relationship between a physical address and WWN cannot be determined from the BIOS. The physical address and WWN must be recorded as a pair when each Fibre Channel card is installed. Physical address and WWN must be assigned to "WWN instance management table for the server". The procedures are described below: (1) Install the Fibre Channel card (2) Turn on the server (3) Acquire the physical address and WWN for the Fibre Channel card (4) Add a record for the server in the WWN instance management table for the server 21

22 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards The following describes the procedure: Procedure 1 Install the Fibre Channel card to the server. For the installation method, position (PCI bus slots), and notes regarding the Fibre Channel card, refer to the manual provided with the Fibre Channel card or the User Guide of the server. 2 Turn on the server, and press the [Ctrl] + [Q] keys while the following message is displayed. "Fast!UTIL" program starts up (Startup may take longer than usual). QLogic Corporation QLA23xx PCI Fibre Channel ROM BIOS Version *.** Copyright(C) QLogic Corporation All rights reserved Press <CTRL-Q> for Fast!UTIL When the "Fast!UTIL" program is started in a single-fibre-channel-card-installed environment, the following window appears. Adapter Type QLA2xxx Select Host Adapter I/O Address 3400 Fast!UTIL Options Configuration Settings Scan Fibre Devices Fibre Disk Utility Select Host Adapter Exit Fast!UTIL When the "Fast!UTIL" program is started in a multiple-fibre-channel-cards-installed environment, the [Select Host Adapter] window appears. Select the second Fibre Channel card, and press the [Enter] key to get the above window. Select Host Adapter Adapter Type I/O Address QLA2xxx 3400 QLA2xxx 3800 When two 2-port Fibre Channel cards are installed (for a total of four ports), four choices are displayed on this screen. 22

23 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards 3 Check the value of [I/O Address]. The value of [I/O Address] is the physical address. Adapter Type QLA2xxx Select Host Adapter I/O Address 3400 Physical address 4 Select [Configuration Settings] from [Fast!UTIL Options] menu. 5 Select [Host Adapter Settings] and press the [Enter] key. Configuration Settings Host Adapter Settings Selectable Boot Settings Restore Default Settings Raw Nvram Data Advanced Adapter Settings Extended Firmware Settings Check the value of [Adapter Port Name]. The value of [Adapter Port Name] is the Fibre Channel card WWN. Host Adapter Settings BIOS Address BIOS Revision Adapter Serial Number Interrupt Level Adapter Port Name Host Adapter BIOS :xxxxx :x.xx :xxxxxx :xx :200000E08B0214D0 :Disabled 6 Record the physical address and WWN in the "WWN instance management table for the server". This table is provided in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 39). The following shows an example of this. Host name Server#1 IP Address Physical slot name Fibre Channel card WWN Instance name Physical address Cable tag slot E0 8B D SERV1_SLOT0 to SN200_1_port0 23

24 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards Details of contents Host name: IP Address: Physical slot name: Fibre Channel card WWN: Instance name: Physical address: Cable tag: Record the host name. Record the IP address of the server. Record the slot position of installed Fibre Channel card. Record the value of [Adapter Port Name]. Not necessary to record. Record the value of [I/O Address]. Record a tag name which indicates the connection path (relationship between the connected device and the port). 7 Check the values for each parameter in the [Host Adapter Settings] window. Refer to the section for the installed Fibre Channel card in "2.2.5 Setting Up the Fibre Channel Card BIOS" (page 30) and set each value. For details on how to set the values, refer to Fibre Channel card user guide. 8 Return to the [Configuration Settings] menu by pressing the [Esc] key. 9 Select [Advanced Adapter Settings] and press the [Enter] key. Configuration Settings Host Adapter Settings Selectable Boot Settings Restore Default Settings Raw Nvram Data Advanced Adapter Settings Extended Firmware Settings 10 Check the values for each parameter in the [Advanced Adapter Settings] window. Refer to the section for the installed Fibre Channel card in "2.2.5 Setting Up the Fibre Channel Card BIOS" (page 30) and set each value. Advanced Adapter Settings Execution Throttle LUNs per Target Enable LIP Reset Enable LIP Full Login Enable Target Reset Login Retry Count Port Down Retry Count Link Down Timeout Extended Error Logging RIO Operation Mode Interrupt Delay Timer :xx :8 :No :Yes :Yes :8 :30 :30 :Disabled :0 :0 24

25 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards 11 Press the [Esc] key twice to return to the [Fast!UTIL Options] menu. If the BIOS settings were changed, save the settings using [Save xxxxxx]. When two or more Fibre Channel cards are installed in the server, select the second or later Fibre Channel card using the following Steps, and set the BIOS of selected card Select [Select Host Adapter] and press the [Enter] key. Fast!UTIL Options Configuration Settings Scan Fibre Devices Fibre Disk Utility Select Host Adapter Exit Fast!UTIL 11-2 Select the Fibre Channel card to be set (BIOS setting) in the [Select Host Adapter] window. The [Fast!UTIL Options] menu appears. Then perform Step 2 through Step 11 shown here. Select Host Adapter Adapter Type I/O Address QLA2xxx 3400 QLA2xxx Select [Exit Fast!UTIL] and press the [Enter] key. 13 Select [Reboot System] and press the [Enter] key. Server reboots. To return to the [Fast!UTIL] menu, select [Return to Fast!UTIL]. Exit Fast!UTIL Reboot System Return to Fast!UTIL End of procedure 25

26 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards Setting Up SAN Boot The following describes the procedure when performing SAN Boot. Depending on the Fibre Channel card used, the actual on-screen Fibre Channel card information may differ from that in the screenshots shown in this document. Procedure 1 Turn on the server, and press the [Ctrl] + [Q] keys while the following message is displayed. "Fast!UTIL" program starts up (Startup may take longer than usual). QLogic Corporation QLA23xx PCI Fibre Channel ROM BIOS Version *.** Copyright(C) QLogic Corporation All rights reserved Press <CTRL-Q> for Fast!UTIL 2 Select [Configuration Settings] and press the [Enter] key. 3 Select [Host Adapter Settings] and press the [Enter] key. Configuration Settings Host Adapter Settings Selectable Boot Settings Restore Default Settings Raw Nvram Data Advanced Adapter Settings Extended Firmware Settings 26

27 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards 4 Check the value of [Host Adapter BIOS]. Set the [Host Adapter BIOS] to "Enabled". For details of the setting procedure, refer to the Fibre Channel card user's guide. When setting parameter other than the [Host Adapter BIOS], refer to "2.2.5 Setting Up the Fibre Channel Card BIOS" (page 30). Host Adapter Settings BIOS Address BIOS Revision Adapter Serial Number Interrupt Level Adapter Port Name Host Adapter BIOS Frame Size Loop Reset Delay Adapter Hard Loop ID Hard Loop ID Spinup Delay Connection Options Fibre Channel Tape Support Data Rate :xxxxx :x.xx :xxxxxx :xx :200000E08B0214D0 :Disabled :2048 :5 :Disabled :0 :Disabled :2 :Enabled :2 5 Return to the [Configuration Settings] menu by pressing the [Esc] key. 6 Press the [Esc] key twice to return to the [Fast!UTIL Options] menu. If the BIOS settings were changed, save the settings using [Save xxxxxx]. When two or more Fibre Channel cards are installed in the server, select the second or later Fibre Channel card using the following Steps, and set the BIOS of selected card. 7 Select [Select Host Adapter] from the [Fast!UTIL Options] menu and press the [Enter] key. Fast!UTIL Options Configuration Settings Scan Fibre Devices Fibre Disk Utility Select Host Adapter Exit Fast!UTIL 7-1 Select the Fibre Channel card to be set (BIOS setting). Select Host Adapter Adapter Type I/O Address QLA2xxx 3400 QLA2xxx The [Fast!UTIL Options] menu appears. Then perform Step 2 through Step 6 shown here. 8 Select [Exit Fast!UTIL] and press the [Enter] key. 27

28 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards 9 Select [Reboot System] and press the [Enter] key. Server reboots. To return to the [Fast!UTIL] menu, select [Return to Fast!UTIL]. Exit Fast!UTIL Reboot System Return to Fast!UTIL End of procedure Setting the Selectable Boot Procedure 1 Select [Selectable Boot Settings] from the [Configuration Settings] menu and press the [Enter] key. 2 Set [Selectable Boot] to "Enabled". 3 Set a boot path (ETERNUS Disk storage system port WWN) and boot LUN#. The boot path and boot LUN# selection window only appears when [Host Adapter BIOS] is "Enabled" in [SAN Boot]. If [Host Adapter BIOS] is "Disabled", the boot path and boot LUN# selection window does not appear. Instead, the window shown in Step 4 appears when [Selectable Boot Settings] is selected. 4 Check the values for each parameter. Selectable Boot Settings Selectable Boot Boot Port Name, Lun :Disabled : ,0 28

29 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards Parameter Value Remarks Selectable Boot Boot Port Name, Lun Enabled or Disabled ETERNUS Disk storage system port WWN, LUN# or , 0 The factory default value is [Disabled]. [Enabled] for SAN Boot. [Disabled] for non SAN Boot. The factory default value is " , 0". "Boot path (ETERNUS Disk storage system port WWN), boot LUN#" for SAN Boot. " , 0" for non SAN Boot. 5 Return to the [Configuration Settings] menu by pressing the [Esc] key. 6 Press the [Esc] key twice to return to the [Fast!UTIL Options] menu. If the BIOS settings were changed, save the settings using [Save xxxxxx]. When two or more Fibre Channel cards are installed in the server, select the second or later Fibre Channel card using the following Steps, and set the BIOS of selected card. 6-1 Select [Select Host Adapter] from the [Fast!UTIL Options] menu and press the [Enter] key. Fast!UTIL Options Configuration Settings Scan Fibre Devices Fibre Disk Utility Select Host Adapter Exit Fast!UTIL 6-2 Select the Fibre Channel card to be set (BIOS setting). Select Host Adapter Adapter Type I/O Address QLA2xxx 3400 QLA2xxx The [Fast!UTIL Options] menu appears. Then perform Step 1 through Step 6 shown here. 7 Select [Exit Fast!UTIL] and press the [Enter] key. 29

30 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards 8 Select [Reboot System] and press the [Enter] key. Exit Fast!UTIL Reboot System Return to Fast!UTIL Server reboots. To return to the [Fast!UTIL] menu, select [Return to Fast!UTIL]. End of procedure Installing the VMware ESX Server If the VMware ESX software is not installed in the server, contact your sales representative Setting Up the Fibre Channel Card BIOS When S26361-F3023-E1 Fibre Channel cards are used, set following parameters to the indicated values. If the current parameter values are different, change them to the indicated values. All other parameters should be left on their default values. [Host Adapter Settings] window Parameter Value Default Remarks BIOS Address BIOS Revision (*1) Adapter Serial Number Interrupt Level Adapter Port Name Host Adapter BIOS Fixed for each card Settings cannot be changed. Enabled or Disabled Disabled Frame Size Loop Reset Delay 5 5 Adapter Hard Loop ID Disabled Disabled Hard Loop ID 0 0 Spinup Delay Disabled Disabled Connection Options 0 (FC-AL) 1 (fabric) 2 Set [Enabled] for SAN Boot. Set [Disabled] for non SAN Boot. Set "0" for FC-AL connection. Set "1" for fabric connection. 30

31 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards Parameter Value Default Remarks Fibre Channel Tape Support Data Rate Disabled 0 (1Gb/s) 1 (2Gb/s) Enabled 2 (Auto Select) Change the setting from "Enabled" to "Disabled". For fabric connection - Set "0" for a 1Gbps Fibre Channel switch - Set "1" for an 8Gbps, 4Gbps, or 2Gbps Fibre Channel switch For FC-AL connection - Set "0" for a 1Gbps CA (maximum speed) - Set "1" for a 4Gbps or 2Gbps CA (maximum speed) *1: BIOS version of the Fibre Channel card is displayed. Check that the BIOS version is the same as shown in "Server Support Matrix". [Advanced Adapter Settings] window Set following parameters to the indicated values. If the current parameter values are different, change them to the indicated values. Parameter Value Default Value Remarks Execution Throttle LUNs per Target 8 8 Enable LIP Reset No No Enable LIP Full Login Yes Yes Enable Target Reset Yes Yes Login Retry Count 8 8 Port Down Retry Count Link Down Timeout Extended Error Logging Disabled Disabled RIO Operation Mode 0 0 Interrupt Delay Timer

32 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards Setting Up the Fibre Channel Card Driver To connect to the ETERNUS2000, change the parameters for the Fibre Channel card driver. When connecting to the ETERNUS4000 or ETERNUS8000, the parameters for the Fibre Channel card driver do not have to be changed because the default values of the standard driver for VMware ESX are used. Procedure 1 Record the module name for the Fibre Channel card that is loaded into VMware ESX. In the following example, "qla2300_707_vmw" is recorded as the module name. # vmkload_mod -l grep qla2300 qla2300_707_vmw Loaded module name Module names may vary depending on the Fibre Channel card that is used. 2 Check the default value for the Fibre Channel card. Specify the module name for the Fibre Channel card that you recorded in Step 1 and check the default value. # esxcfg-module -g qla2300_707_vmw qla2300_707_vmw enabled = 1 options = '' Check that no value appears. 3 Change the setting value for the number of I/Os on the Fibre Channel card. Driver parameter Number of I/Os when 16 or less LUNs are used Driver parameter setting values Number of I/Os when 17 or more LUNs are used ql2xmaxqdepth 8 4 Use the following command to change the setting values when the driver parameter name is "ql2xmaxqdepth", the number of I/Os is "8", and the module name is "qla2300_707_vmw". # esxcfg-module -s ql2xmaxqdepth=8 qla2300_707_vmw Input the number of I/Os ("8" in this example) for driver parameter setting. 32

33 > 2.2 Setup Procedure for S26361-F3023-E1 Fibre Channel Cards This option cannot be individually applied to each port on the Fibre Channel card. All ports on the target Fibre Channel card are configured with the same settings. 4 Check the setting values. # esxcfg-module -g qla2300_707_vmw qla2300_707_vmw enabled = 1 options = 'l ql2xmaxqdepth =8' 5 Update the loaded module. # esxcfg-boot -b 6 Reboot VMware ESX. # reboot End of procedure 33

34 Chapter 3 For PRIMEQUEST 1000 Series 3.1 Setup Procedure for MC-0JFC11 or MC-0JFC21 Fibre Channel Cards This section describes how to set up the VMware ESX server for use with the MC-0JFC11 or MC-0JFC21 Fibre Channel cards Setting Up the Fibre Channel Card Install the Fibre Channel card to the server and acquire its physical address and WWN (World Wide Name). Physical address and Fibre Channel card WWN are required information in the cases shown as follows; when an error has occurred in the system, when using the ETERNUS Disk storage systems' host affinity function, etc., to restrict server access, or when connecting the ETERNUS Disk storage systems and the server using Fibre Channel switch. The relationship between a physical address and WWN cannot be determined from the BIOS. The physical address and WWN must be recorded as a pair when each Fibre Channel card is installed. Physical address and WWN must be assigned to "WWN instance management table for the server". The procedures are described below: (1) Install the Fibre Channel card (2) Turn on the server (3) Acquire the physical address and WWN for the Fibre Channel card (4) Add a record for the server in the WWN instance management table for the server Add the acquired record in the "WWN instance management table for the server" (found in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 39)). 34

35 Chapter 3 For PRIMEQUEST 1000 Series > 3.1 Setup Procedure for MC-0JFC11 or MC-0JFC21 Fibre Channel Cards The following describes the procedure: Procedure 1 Install the Fibre Channel card to the server. For the installation method, slot positions and notes regarding the Fibre Channel card, refer to the manual provided with the Fibre Channel card or the User Guide of the server. 2 Use the UEFI Shell to enter the following command to output a list of the drivers. shell > drivers 3 Specify the identification number of the target driver. shell > drvcfg -s Driver_identification_number 4 Enter the number of the Fibre Channel card to be checked and press the [Enter] key. Select the HBA to set or check from the output HBA list. 5 Display the HBA setup utility. Select [1. Setup Utility] from the displayed menu. 6 Check the [I/O Base] and [Port Name] values. Check the [I/O Base] and [Port Name] values from the displayed menu. The value of [I/O Base] is the physical address and the value of [Port Name] is WWN. Example: 35

36 Chapter 3 For PRIMEQUEST 1000 Series > 3.1 Setup Procedure for MC-0JFC11 or MC-0JFC21 Fibre Channel Cards 7 Record the physical address and WWN in the "WWN instance management table for the server". This table is provided in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 39). The following shows an example of this. Host name Server#1 IP Address Physical slot name Fibre Channel card WWN Instance name Physical address Cable tag slot C9 38 D SERV1_SLOT0 to SN200_1_port0 Details of contents Host name: IP Address: Physical slot name: Fibre Channel card WWN: Instance name: Physical address: Cable tag: Record the host name. Record the IP address of the server. Record the slot position of installed Fibre Channel card. Record the value of [Port Name]. Not necessary to record. Record the value of [I/O Base]. Record a tag name which indicates the connection path (relationship between the connected device and the port). 8 Press the [ESC] key to quit [Setup Utility]. When the total number of ports for installed Fibre Channel cards is two or more, repeat Step 1 through Step 6 above for each port, and record the information for all ports in the "WWN instance management table for the server". End of procedure Setting SAN Boot If a SAN Boot environment is to be set up, the SAN Boot settings must be made beforehand for the PRIMEQUEST 1000 series. Refer to "Appendix D Configuration in the SAN Boot Environment" in "PRIMEQUEST 1000 series INSTALLATION MANUAL" for details Installing the VMware ESX Server VMware ESX should be installed now if it has not yet been installed on the server. Refer to the following URL for details. 36

37 Chapter 3 For PRIMEQUEST 1000 Series > 3.1 Setup Procedure for MC-0JFC11 or MC-0JFC21 Fibre Channel Cards Setting Up the Fibre Channel Card Driver To connect to the ETERNUS2000, change the parameters for the Fibre Channel card driver. When connecting to the ETERNUS4000 or ETERNUS8000, the parameters for the Fibre Channel card driver do not have to be changed because the default values of the standard driver for VMware ESX are used. Procedure 1 Record the module name for the Fibre Channel card that is loaded into VMware ESX. In the following example, "lpfc820" is recorded as the module name. # vmkload_mod -l grep lpfc* lpfc820 Loaded module name Module names may vary depending on the Fibre Channel card that is used. 2 Check the default value for the Fibre Channel card. Specify the module name for the Fibre Channel card that you recorded in Step 1 and check the default value. # esxcfg-module -g lpfc820 lpfc820 enabled = 1 options = '' Check that no value appears. 3 Check the number of ports on the Fibre Channel card. The SCSI Host numbers of the Fibre Channel card that are displayed represent the number of ports. In the following example, the number of ports is "two" since "4" and "5" (two numbers) are displayed as the SCSI Host numbers of the Fibre Channel card. # ls /proc/scsi/lpfc 4 5 The number of ports is "two". 37

38 Chapter 3 For PRIMEQUEST 1000 Series > 3.1 Setup Procedure for MC-0JFC11 or MC-0JFC21 Fibre Channel Cards 4 Change the setting values of the parameter for the Fibre Channel card driver. Driver parameter Number of I/Os when 16 or less LUNs are used Driver parameter setting values Number of I/Os when 17 or more LUNs are used lpfcx_lun_queue_depth 8 4 Use the following command to change the setting values when the driver parameter name is "lpfcx_lun_queue_depth", the number of I/Os is "8", the module name is "lpfc820", and the number of ports is "2". # esxcfg-module -s "lpfc0_lun_queue_depth=8 lpfc1_lun_queue_depth=8" lpfc820 Input the number of I/Os ("8" in this example) for each driver parameter setting. 5 Check the setting values. # esxcfg-module -g lpfc820 lpfc820 enabled = 1 options = 'lpfc0_lun_queue_depth=8 lpfc1_lun_queue_depth=8' 6 Reboot VMware ESX. # reboot End of procedure 38

39 Appendix A WWN Instance Management Table for the Server (Blank) This table is used when checking the Fibre Channel cards, and should be used as necessary. WWN instance management table for the server Host name IP Address Physical slot name Fibre Channel card WWN Instance name Physical address Cable tag 39

40 ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for VMware ESX Driver Settings for PRIMERGY/PRIMEQUEST 1000 Series Date of issuance: December 2010 Issuance responsibility: FUJITSU LIMITED The contents of this manual are liable to being updated without notice. While the contents of this manual are the product of all due care and diligence, no responsibility can be accepted for operational problems arising from any errors or missing information, or other use of the information contained in this manual. Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. Contents of this manual are not to be reproduced without permission from Fujitsu.

41