The Contents and Structure of this Manual. This document is composed of the following three chapters and an appendix.

Transcription

1

2

3 Preface This document briefly explains the operations that need to be performed by the user in order to connect an ETERNUS2000 model 100 or 200, ETERNUS4000 model 300, 400, 500, or 600, or ETERNUS8000 model 700, 800, 900, 1100, 1200, 2100, or 2200 Disk storage system to an Industry Standard Server running Windows. This document should be used in conjunction with other applicable user manuals such as those for the ETERNUS2000 model 100 or 200, ETERNUS4000 model 300, 400, 500, or 600, or ETERNUS8000 model 700, 800, 900, 1100, 1200, 2100, or 2200 Disk storage system, server, OS used, Fibre Channel cards, drivers, etc. This document references the following documents: Server Support Matrix ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) ETERNUS Disk Storage System Settings ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for Windows Also, note that in this document the ETERNUS2000 models 100 and 200, ETERNUS4000 models 300, 400, 500, and 600, and ETERNUS8000 models 700, 800, 900, 1100, 1200, 2100, and 2200 Disk storage systems are collectively referred to as ETERNUS Disk storage systems. Fifth Edition April 2010 The Contents and Structure of this Manual This document is composed of the following three chapters and an appendix. Chapter 1 Workflow This describes how to connect an ETERNUS Disk storage system to a PRIMERGY or PRIMEQUEST 1000 series server. Chapter 2 Setup Procedure for PRIMERGY This describes how to install a Fibre Channel card, set up the Fibre Channel card BIOS, install the Fibre Channel card driver, check the driver version, and set up the driver parameters for PRIMERGY. Chapter 3 Setup Procedure for PRIMEQUEST 1000 series This describes how to install a Fibre Channel card, set up the Fibre Channel card BIOS, install the Fibre Channel card driver, check the driver version, and set up the driver parameters for PRIMEQUEST 1000 series. An appendix contains a WWN instance management table for servers, for use in the "Installing the Fibre Channel Card" section. 3

4 Preface Safe Use of this Product Using this manual This manual contains important information to ensure the safe use of this product. Be sure to thoroughly read and understand its contents before using the product. After reading, store this manual in a safe place for future reference. FUJITSU has made every effort to ensure the safety of the users and other personnel, and to prevent property damage. When using this product, carefully follow the instructions described in this manual. Acknowledgments Microsoft, Windows, and Windows Server are either registered trademarks or trademarks of Microsoft Corporation in the U.S. and/or other countries. Emulex is a trademark of Emulex Corp. QLogic is a trademark of QLogic Corp. The company names, product names and service names mentioned in this document are registered trademarks or trademarks of their respective companies. Naming Conventions OS names "Windows Server 2008 R2" represents the following products. - Microsoft Windows Web Server 2008 R2 - Microsoft Windows Server 2008 R2 Standard - Microsoft Windows Server 2008 R2 Enterprise - Microsoft Windows Server 2008 R2 Datacenter - Microsoft Windows Server 2008 R2 for Itanium-based Systems "Windows Server 2008" represents the following products. - Microsoft Windows Server 2008 Standard - Microsoft Windows Server 2008 Enterprise - Microsoft Windows Server 2008 Datacenter - Microsoft Windows Server 2008 for Itanium-based Systems "Windows Server 2003" represents the following products. - Microsoft Windows Server 2003, Standard Edition - Microsoft Windows Server 2003, Enterprise Edition - Microsoft Windows Server 2003, Standard x64 Edition - Microsoft Windows Server 2003, Enterprise x64 Edition 4

5 Preface - Microsoft Windows Server 2003 R2, Standard Edition - Microsoft Windows Server 2003 R2, Enterprise Edition - Microsoft Windows Server 2003 R2, Standard x64 Edition - Microsoft Windows Server 2003 R2, Enterprise x64 Edition - Microsoft Windows Server 2003, Enterprise Edition for Itanium-based Systems - Microsoft Windows Server 2003, Datacenter Edition for Itanium-based Systems - Microsoft Windows Storage Server 2003 R2, Standard Edition - Microsoft Windows Storage Server 2003 R2, Enterprise Edition - Microsoft Windows Storage Server 2003 R2, Standard x64 Edition - Microsoft Windows Storage Server 2003 R2, Enterprise x64 Edition "Windows 2000" represents the following products. - Microsoft Windows 2000 Server operating system - Microsoft Windows 2000 Advanced Server operating system Other names "Channel Adapter" (CA) refers to the Fibre Channel interface module used in the ETERNUS Disk storage systems to connect to the server. "Fibre Channel card" refers to the Fibre Channel interface module normally used in the server. A "Host Bus Adapter" (HBA) or "Channel Adapter" (CA) may be used instead, depending on the server. "Fibre Channel cable" refers to the cable that is used to connect the ETERNUS Disk storage systems and server via a Fibre Channel interface. "FC cable", "optical fibre cable", or "multi mode Fibre Channel cable" may be used instead, depending on the storage system. Italics are used to show variables such as values and characters that appear in command parameters and output examples. Screen shot(s) reprinted with permission from Microsoft Corporation. 5

6 Contents Chapter 1 Workflow...7 Chapter 2 Setup Procedure for PRIMERGY Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards Installing the Fibre Channel Card Installing the Drivers Checking the Driver Version Setting up the Driver Parameters Setting Fixed Target IDs (for Windows Server 2008 and Windows Server 2003) Installing the ETERNUS Disk Storage System Driver Setup Procedure for the S26361-F3023-E1 Fibre Channel Card Installing the Fibre Channel Card Installing the Drivers Checking the Driver Version Installing the ETERNUS Disk Storage System Driver Chapter 3 Setup Procedure for PRIMEQUEST 1000 series Setup Procedure for MC-0JFC11 and MC-0JFC21 Fibre Channel Cards Installing the Fibre Channel Card Installing the Drivers Checking the Driver Version Setting up the Driver Parameters Setting Fixed Target IDs (for Windows Server 2008 and Windows Server 2003) Installing the ETERNUS Disk Storage System Driver Appendix A WWN Instance Management Table for the Server (Blank)

7 Chapter 1 Workflow This chapter describes how to install and set up the Fibre Channel cards in a PRIMERGY or PRIMEQUEST 1000 series server. Workflow Install the Fibre Channel Card Install the Fibre Channel card and its driver, check the driver version, and set up the Fibre Channel card BIOS. Refer For PRIMERGY - For the S26361-F2624-E1, S26361-F2843-E1/S26361-F2843-E201, S26361-F3141- E10/S26361-F3141-E210, S26361-F3141-E1, S26361-F3306-E1/S26361-F3306- E201, S26361-F3961-E1/S26361-F3961-E201, S26361-F3961-E2/S26361-F3961- E202, S26361-F3306-E601, or MC-FC82E Fibre Channel card "2.1.1 Installing the Fibre Channel Card" (page 10) "2.1.2 Installing the Drivers" (page 11) - For the S26361-F3023-E1 Fibre Channel card "2.2.1 Installing the Fibre Channel Card" (page 19) "2.2.2 Installing the Drivers" (page 23) For PRIMEQUEST 1000 series - For the MC-0JFC11 or MC-0JFC21 Fibre Channel card "3.1.1 Installing the Fibre Channel Card" (page 25) "3.1.2 Installing the Drivers" (page 26) For PRIMERGY (not S26361-F3023-E1) or For PRIMEQUEST 1000 series (MC-0JFC11 or MC-0JFC21) For PRIMERGY (S26361-F3023-E1) 7

8 Chapter 1 Workflow > Set the Fibre Channel Card Driver Parameters Set the Topology, Queue Depth and other parameters. Refer For PRIMERGY - "2.1.4 Setting up the Driver Parameters" (page 12) For PRIMEQUEST 1000 series - "3.1.4 Setting up the Driver Parameters" (page 27) Install the ETERNUS Disk Storage System Driver Refer Install the ETERNUS Disk Storage System Driver. For PRIMERGY - For the S26361-F2624-E1, S26361-F2843-E1/S26361-F2843-E201, S26361-F3141- E10/S26361-F3141-E210, S26361-F3141-E1, S26361-F3306-E1/S26361-F3306- E201, S26361-F3961-E1/S26361-F3961-E201, S26361-F3961-E2/S26361-F3961- E202, S26361-F3306-E601, or MC-FC82E Fibre Channel card "2.1.6 Installing the ETERNUS Disk Storage System Driver" (page 18) Check the driver-related notes. "ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for Windows " - For the S26361-F3023-E1 Fibre Channel card "2.2.4 Installing the ETERNUS Disk Storage System Driver" (page 23) Check the driver-related notes. "ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for Windows " For PRIMEQUEST 1000 series - For the MC-0JFC11 or MC-0JFC21 Fibre Channel card "3.1.6 Installing the ETERNUS Disk Storage System Driver" (page 29) Check the driver-related notes. "ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for Windows " Once all these steps have been completed, proceed as described in "ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for Windows ". 8

9 Chapter 2 Setup Procedure for PRIMERGY The setup procedure varies depending on the product ID of the Fibre Channel card being used. For the S26361-F2624-E1, S26361-F2843-E1/S26361-F2843-E201, S26361-F3141-E10/ S26361-F3141-E210, S26361-F3141-E1, S26361-F3306-E1/S26361-F3306-E201, S F3961-E1/S26361-F3961-E201, S26361-F3961-E2/S26361-F3961-E202, S26361-F3306- E601, and MC-FC82E Fibre Channel cards, proceed to "2.1 Setup Procedure for non- S26361-F3023-E1 Fibre Channel Cards" (page 9). For the S26361-F3023-E1 Fibre Channel card, proceed to "2.2 Setup Procedure for the S26361-F3023-E1 Fibre Channel Card" (page 19). 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards Install the Fibre Channel cards in the server, and acquire their physical addresses and World Wide Names (WWNs). The physical address and WWN of a Fibre Channel card are required information in the following cases: when an error has occurred in the system, when using the ETERNUS Disk storage systems (security function, host affinity function, etc.) to restrict server access, or when connecting the ETERNUS Disk storage systems and the server using Fibre Channel switch. Acquire the physical address and WWN when installing the Fibre Channel card, because they cannot be determined from BIOS and OS. Physical address and WWN must be assigned to "WWN instance management table for the server". (1) Install the Fibre Channel card (2) Turn on the server (3) Acquire the physical address and WWN for the Fibre Channel card (4) Add a record for the server in the WWN instance management table for the server When installing two or more Fibre Channel cards to the server, first turn off the server, then repeat Steps (1) through (4) above for each Fibre Channel card to be installed. 9

10 Chapter 2 Setup Procedure for PRIMERGY > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards Installing the Fibre Channel Card For the installation method, position (PCI bus slots), and notes regarding the Fibre Channel card, refer to the Fibre Channel card documentation or the User Guide of the server. Procedure 1 Turn on the server, and press the [Alt] + [E] keys while the following message is displayed.!!! Emulex LPexxxx BIOS Copyright xxxx!!! xxxxxxxx Press <Alt E> to go to Emulex BIOS Utility. Press <s> to skip Emulex BIOS. "LightPulse BIOS Utility" starts. 2 Enter the number of the Fibre Channel card to be checked in [Enter a Selection:_] and press the [Enter] key. 3 Check the [I/O Base] and [Port Name] values. The value of [I/O Base] is the physical address and the value of [Port Name] is the Fibre Channel card WWN. Adapter 1: PCI Bus#:0x PCI Device#:0x Physical address LPexxxx: I/O Base: 5000 Firmware Version: xxxxxxxx Port Name: C938D229 Node Name: C938D229 Topology: Auto Topology: Loop first(default) Fibre Channel card WWN 1.Configure Boot Device 2.Configure This Adapter s Parameters Enter a Selection:_ Enter <x> to Exit <d> to Default Values <Page Up> to Previous Menu 4 Record the physical address and WWN in the WWN instance management table for the server (found in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 30)). The following shows an example of this. Host name IP Address Physical slot name Fibre Channel card WWN Instance name Physical address slot C9 38 D Cable tag 10

11 Chapter 2 Setup Procedure for PRIMERGY > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards Details of contents The details of contents for the WWN instance management table for the server are as follows: Host name: IP address: Physical slot name: Fibre Channel card WWN: Instance name: Physical address: Cable tag: Record the host name. Record the IP address of the server. Record the slot position of installed Fibre Channel card. For the installation location, refer to the User Guide for each server. Record the value of [Port Name] or [Adapter Port Name]. Not necessary to record. Record the value of [I/O Base] or [I/O Address]. Record a tag name which indicates the connection path (relationship between the connected device and the port). 5 Press the [x] key to exit "LightPulse BIOS Utility". When installing two or more Fibre Channel cards to the server, first turn off the server, then repeat Step 1 through Step 4 for each Fibre Channel card to be installed. If two or more Fibre Channel cards have already been installed in the server at the time of purchase, the one-to-one relationship between the WWNs and Fibre Channel cards may not be easy to determine. The correct WWPNs need to be registered and setup on the ETERNUS Disk storage system for a server to recognize the ETERNUS Disk storage system logical disks. If logical volumes are not recognized by a server, the WWPN maybe registered to an incorrect CM/CA Port. The WWN field on the WWN Registration maybe useful in identifying which Fibre Channel card is connected to which CM/CA Port. For most (but not all) configurations, the WWN field lists the WWNs of accessible HBAs. Refer to "ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) ETERNUS Disk Storage System Settings" for details about ETERNUS settings. End of procedure Installing the Drivers Refer to the documentation provided with each Fibre Channel card for details on how to obtain and install a Fibre Channel card driver for it. 11

12 Chapter 2 Setup Procedure for PRIMERGY > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards Checking the Driver Version Use the Device Manager to check the version of the Fibre Channel card driver. Procedure 1 In the Device Manager go to [SCSI and RAID controllers], and open the [Properties] of the Fibre Channel card. 2 Select the [Driver] tab, and open the [Driver Details]. 3 Select the driver file, and check its [File version]. For SCSIport Miniport driver: select "lpxnds.sys" for the driver file. For Storport Miniport driver: select "elxstor.sys" for the driver file. If a different driver version is displayed from that shown in "Server Support Matrix", reinstall the driver. End of procedure Setting up the Driver Parameters The procedure varies depending on the product ID of the Fibre Channel card being used. For the S26361-F2624-E1, S26361-F2843-E1/S26361-F2843-E201, S26361-F3141-E10/ S26361-F3141-E210, and S26361-F3141-E1 Fibre Channel cards, proceed to " For the S26361-F2624-E1, S26361-F2843-E1/S26361-F2843-E201, S26361-F3141-E10/ S26361-F3141-E210, and S26361-F3141-E1" (page 13). For the S26361-F3306-E1/S26361-F3306-E201, S26361-F3961-E1/S26361-F3961-E201, S26361-F3961-E2/S26361-F3961-E202, S26361-F3306-E601, and MC-FC82E Fibre Channel cards, proceed to " For the S26361-F3306-E1/S26361-F3306-E201, S F3961-E1/S26361-F3961-E201, S26361-F3961-E2/S26361-F3961-E202, S26361-F3306- E601, and MC-FC82E" (page 15). Use the application (HBAnyware, OneCommand Manager, or other) provided by Emulex Corp. to set the driver parameters. This chapter describes the procedures using HBAnyware. 12

13 Chapter 2 Setup Procedure for PRIMERGY > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards For the S26361-F2624-E1, S26361-F2843-E1/S26361-F2843-E201, S F3141-E10/S26361-F3141-E210, and S26361-F3141-E1 Set the driver parameters after installing HBAnyware. Procedure 1 Install HBAnyware. For installation, refer to the User Guide of S26361-F2624-E1, S26361-F2843-E1/S F2843-E201, S26361-F3141-E10/S26361-F3141-E210, or S26361-F3141-E1 Fibre Channel card. The Driver Parameter Setting Tool (LightPulse Utility/NT) is included in HBAnyware. 2 Start up the "LightPulse Utility/NT". 3 Select [Driver Parameters] from [Category:]. 4 Select [Registry] with the radio button. The registry contents are displayed. The display contents vary according to the installed Fibre Channel card type and the driver version. 5 Double click the [Device]. The [Modify Registry Entry] dialog box is displayed. 6 Check the current values of each parameter. Check the value of each parameter in the following tables, and correct the current value if necessary. If the parameter is not shown, add the necessary information. - For Windows Server 2003 Fibre Channel card Topology QueueDepth Value Queue Target LinkSpeed S26361-F3141- E1 S26361-F3141- E10/S F3141-E210 S26361-F2843- E1/S F2843-E201 0 (FC-AL Connection) 1 (Fabric Connection) ETERNUS Calculated value (*1) ETERNUS4000, ETERNUS "255" for SCSIport Miniport Driver - "254" for Storport Miniport Driver 1 2 (FC-AL Connection, 8Gbps Switch Connection, 4Gbps Switch Connection, 2Gbps Switch Connection) 1 (1Gbps Switch Connection) 13

14 Chapter 2 Setup Procedure for PRIMERGY > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards - For Windows 2000 Fibre Channel card S26361-F3141- E1 S26361-F3141- E10/S F3141-E210 S26361-F2843- E1/S F2843-E201 S26361-F2624- E1 *1: Use the following formula to calculate the proper setting value: Value = 40 / (No. of Server-side Fibre Channel ports connected to each ETERNUS-side CA port) (Round the result down) Use the value of "8" if the actual result is lower. The following describes each parameter: - "Topology" parameter Set the connection type of the server and ETERNUS Disk storage systems. - "QueueDepth" parameter Set the command queue depth. - "QueueTarget" parameter Set to specify the command queue depth to either the LUN or to the target. - "LinkSpeed" parameter Set the LinkSpeed. Topology 0 (FC-AL Connection) 1 (Fabric Connection) QueueDepth ETERNUS Calculated value (*1) ETERNUS4000, ETERNUS "255" Value Queue Target LinkSpeed 7 After all the cards have been set, select [Exit] from the [File] menu to quit the "LightPulse Utility/NT". 1 2 (FC-AL Connection, 8Gbps Switch Connection, 4Gbps Switch Connection, 2Gbps Switch Connection) 1 (1Gbps Switch Connection) If correcting or adding parameters, note the following restrictions. Describe each parameter, using ";" (semicolon) to delimit. Enter each parameter, using correct spelling. Note that misspelled words are not checked. Do not modify any parameters other than those described here. End of procedure 14

15 Chapter 2 Setup Procedure for PRIMERGY > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards For the S26361-F3306-E1/S26361-F3306-E201, S26361-F3961-E1/S F3961-E201, S26361-F3961-E2/S26361-F3961-E202, S26361-F3306-E601, and MC-FC82E Set the driver parameters after installing HBAnyware. When the server OS is Windows Server 2008 or Windows Server 2003, it is recommended that fixed Target IDs be assigned to the Fibre Channel card connected devices, and that automatic Target ID allocation be disabled. For details of the Target ID settings, refer to the "Fibre Channel Controller User's Guide". By default, Target IDs are automatically allocated. However, when a device is added, automatic Target ID allocation can result in a different distribution of Target IDs, which can cause the devices to not be recognized. Procedure 1 Install HBAnyware. For installation, refer to the Fibre Channel card documentation. 2 Start the HBAnyware Utility. 3 Select the target Fibre Channel card and click the [Driver Parameters] tab. When the same parameter values are to be set for all the Fibre Channel cards (common setting), select the target server instead of the target Fibre Channel card and click the [Driver Parameters] tab. 4 Check the parameter values in the [Adapter Parameter] list. Compare with the parameter values in the following tables, and correct the current value if necessary. Select the parameter whose value is to be corrected from the [Adapter Parameter] list and modify the value in the [Modify Adapter Parameter] area. 15

16 Chapter 2 Setup Procedure for PRIMERGY > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards - For Windows Server 2008 Fibre Channel card S26361-F3961- E2/S F3961-E202, S26361-F3961- E1/S F3961-E201, S26361-F3306- E1/S F3306-E201, S26361-F3306- E601, MC-FC82E - For Windows Server 2003 Fibre Channel card S26361-F3961- E2/S F3961-E202, S26361-F3961- E1/S F3961-E201, S26361-F3306- E1/S F3306-E201, S26361-F3306- E601, MC-FC82E - For Windows 2000 Fibre Channel card S26361-F3306- E1/S F3306-E201 Topology 0 (FC-AL Connection) 1 (Fabric Connection) Topology 0 (FC-AL Connection) 1 (Fabric Connection) Topology 0 (FC-AL Connection) 1 (Fabric Connection) QueueDepth ETERNUS Calculated value (*1) ETERNUS4000, ETERNUS "254" QueueDepth ETERNUS Calculated value (*1) Value Value ETERNUS4000, ETERNUS "255" for SCSIport Miniport Driver - "254" for Storport Miniport Driver QueueDepth ETERNUS Calculated value (*1) ETERNUS4000, ETERNUS "255" Value Queue Target LinkSpeed *1: Use the following formula to calculate the proper setting value: Value = 40 / (No. of Server-side Fibre Channel ports connected to each ETERNUS-side CA port) (Round the result down) Use the value of "8" if the actual result is lower. 1 Queue Target 1 Queue Target 1 See the Link Speed settings table (*2), below LinkSpeed See the Link Speed settings table (*2), below LinkSpeed See the Link Speed settings table (*2), below 16

17 Chapter 2 Setup Procedure for PRIMERGY > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards *2: LinkSpeed settings: Fibre Channel card S26361-F3961- E2/S F3961-E202, S26361-F3961- E1/S F3961-E201, MC-FC82E S26361-F3306- E1/S F3306-E201, S26361-F3306- E601 Fabric connection (Fibre Channel switch connection) Maximum Fibre Channel switch link speed 8Gbps 4Gbps 2Gbps 1Gbps ETERNUS 2000 FC-AL connection ETERNUS4000, ETERNUS8000 8Gbps FC-CA 4Gbps FC-CA Do not modify any parameters other than those described here. The following describes each parameter: - "Topology" parameter Set the connection type of the server and ETERNUS Disk storage systems. - "QueueDepth" parameter Set the command queue depth. - "QueueTarget" parameter Set to specify the command queue depth to either the LUN or to the target. - "LinkSpeed" parameter Set the LinkSpeed. 17

18 Chapter 2 Setup Procedure for PRIMERGY > 2.1 Setup Procedure for non-s26361-f3023-e1 Fibre Channel Cards 5 After the values have been modified, click the [Apply] button. Values that have been modified but not yet applied are displayed in red in the [Value] column. Click the [Apply] button. 6 If there are multiple cards, repeat Step 2 through Step 4 to change the settings for all cards. 7 After all the cards have been set, select [Exit] from the [File] menu to quit the "HBAnyware Utility". End of procedure Setting Fixed Target IDs (for Windows Server 2008 and Windows Server 2003) Each device connected to a Fibre Channel card is allocated a Target ID. By default, these Target IDs are automatically allocated by the driver. This means that, depending on the state of device recognition, the device Target IDs can and may be reallocated as devices are added and removed. If the Target IDs have changed when the server reboots, devices may end up off-line, and unavailable depending on the OS or application environment being used. Alternatively, automatic Target ID allocation can be disabled and the Fibre Channel card settings manually adjusted to assign an arbitrary Target ID to each device connected to the card. It is recommended that a fixed Target ID be allocated to each device in this way. Contact your supplier for more details Installing the ETERNUS Disk Storage System Driver Install the driver for ETERNUS Disk storage systems to the server if necessary. Refer to "Driver Notes" section in "ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for Windows " for notes on each driver. This section applies when using path redundancy control (path fail-over) for a multipath connected ETERNUS Disk storage system or when connecting the ETERNUS Disk storage system to the server via single-path. For details on how to install, uninstall, set up and operate the ETERNUS Disk storage systems' driver, refer to the Readme file or the User Guide provided with the software. 18

19 Chapter 2 Setup Procedure for PRIMERGY > 2.2 Setup Procedure for the S26361-F3023-E1 Fibre Channel Card 2.2 Setup Procedure for the S26361-F3023-E1 Fibre Channel Card Install the Fibre Channel cards in the server, and acquire their physical addresses and World Wide Names (WWNs). The physical address and WWN of a Fibre Channel card are required information in the following cases: when an error has occurred in the system, when using the ETERNUS Disk storage systems (security function, host affinity function, etc.) to restrict server access, or when connecting the ETERNUS Disk storage systems and the server using Fibre Channel switch. Acquire the physical address and WWN when installing the Fibre Channel card, because they cannot be determined from BIOS and OS. Physical address and WWN must be assigned to "WWN instance management table for the server". (1) Install the Fibre Channel card (2) Turn on the server (3) Acquire the physical address and WWN for the Fibre Channel card (4) Add a record for the server in the WWN instance management table for the server (5) Set the Fibre Channel card BIOS When installing two or more Fibre Channel cards to the server, first turn off the server, then repeat Steps (1) through (5) above for each Fibre Channel card to be installed Installing the Fibre Channel Card For the installation method, position (PCI bus slots), and notes regarding the Fibre Channel card, refer to the Fibre Channel card documentation or the User Guide of the server. Procedure 1 Turn on the server, and press the [Ctrl] + [Q] keys while the following message is displayed. QLogic Corporation QLA23xx PCI Fibre Channel ROM BIOS Version *.** Copyright(C) QLogic Corporation All rights reserved Press <CTRL-Q> for Fast!UTIL "Fast!UTIL" program starts up (Startup may take longer than usual). 19

20 Chapter 2 Setup Procedure for PRIMERGY > 2.2 Setup Procedure for the S26361-F3023-E1 Fibre Channel Card 2 Check the value of [I/O Address] of the [Select Host Adapter] window. The value of [I/O Address] is the physical address. Select Host Adapter Adapter Type QLA2xxx I/O Address 3400 Physical address 3 Select [Configuration Settings] from [Fast!UTIL Options] menu and press the [Enter] key. 4 Select [Host Adapter Settings] from [Configuration Settings] menu and press the [Enter] key. The [Host Adapter Settings] window appears. 5 Check the value of [Adapter Port Name]. The value of [Adapter Port Name] is the Fibre Channel card WWN. Host Adapter Settings BIOS Address BIOS Revision Adapter Serial Number Interrupt Level Adapter Port Name Host Adapter BIOS :xxxxx :x.xx :xxxxxx :xx :200000E08B0214D0 :Disabled 6 Record the physical address and WWN in the WWN instance management table for the server (found in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 30)). The following shows an example of this. Host name Server#1 IP address Physical slot name Fibre Channel card WWN Instance name Physical address Cable tag slot E0 8B D SERV1_SLOT0 to SN200_1_port0 20

21 Chapter 2 Setup Procedure for PRIMERGY > 2.2 Setup Procedure for the S26361-F3023-E1 Fibre Channel Card 7 Set up the Fibre Channel cards BIOS. Check the values for each parameter in the [Host Adapter Settings] window. See the following tables and set each value. For details on how to set the values, refer to BIOS Readme file and Fibre Channel card user guide. Parameter BIOS Address BIOS Revision (*1) Adapter Serial Number Interrupt Level Adapter Port Name Value Fixed for each card Default Value Host Adapter BIOS Enabled or Disabled Disabled Remarks Settings cannot be changed. Set [Enabled] for SAN Boot. Set [Disabled] for non SAN Boot. Frame Size 2048 The factory default values Loop Reset Delay 5 should not need to be Adapter Hard Loop ID Disabled changed. If the current values are Hard Loop ID Disabled different, change them back Spinup Delay Disabled to the factory default values. Connection Options Fibre Channel Tape Support Data Rate 0 (FC-AL connection) (*2), 1 (Fabric connection) (*3) Disabled 0 (1Gbps fixed), or 1 (2Gbps fixed) *1: BIOS version of the Fibre Channel card is displayed. Check that the BIOS version is the same as shown in "Server Support Matrix". *2: When connecting directly to the ETERNUS Disk storage systems via a Fibre Channel passthrough blade. *3: When Fibre Channel Switch is connected to the ETERNUS Disk storage systems via a Fibre Channel pass-through blade or Fibre Channel switch blade. 8 Return to the [Configuration Settings] menu by pressing the [Esc] key. 1 Enabled 2 "0" for an FC-AL connection "1" for a fabric connection "1" for an FC-AL connection "1" for a 8Gbps Fibre Channel switch fabric connection "1" for a 4Gbps Fibre Channel switch fabric connection "1" for a 2Gbps Fibre Channel switch fabric connection "0" for a 1Gbps Fibre Channel switch fabric connection 21

22 Chapter 2 Setup Procedure for PRIMERGY > 2.2 Setup Procedure for the S26361-F3023-E1 Fibre Channel Card. 9 Select [Advanced Adapter Settings] from the [Configuration Settings] menu and press the [Enter] key. Check the parameter values in the [Advanced Adapter Settings] window against those in the following table, and correct the current value if necessary. Parameter Value Default Value Remarks Execution Throttle (*1) LUNs per Target 256 Enable LIP Reset No Enable LIP Full Login Yes Enable Target Reset Yes Login Retry Count 8 Port Down Retry Count 45 Link Down Timeout 45 Extended Error Logging Disabled RIO Operation Mode 0 Interrupt Delay Timer 0 The factory default values should not need to be changed. If the current values are different, change them back to the factory default values. *1: Set "16" in [Execution Throttle]. This setting allows performance to be increased by tuning the command queuing function for commands issued to the ETERNUS Disk storage system from the server. Performance may be degraded if you do not perform this tuning. 10 Press the [Esc] key twice to return to the [Fast!UTIL Options] menu. If the BIOS settings were changed, save the settings using [Save xxxxxx]. When two or more Fibre Channel cards are installed to the server, select the second or later Fibre Channel card using the following Steps, and set the BIOS of selected card Select [Select Host Adapter] from the [Fast!UTIL Options] menu and press the [Enter] key Select the Fibre Channel card to be set (BIOS setting) in [Select Host Adapter] window. The [Fast!UTIL Option] menu appears. Then perform Step 2 through Step Select [Exit Fast!UTIL] and press the [Enter] key. 12 Select [Reboot System] and press the [Enter] key. The server reboots. To return to the [Fast!UTIL] menu, select [Return to Fast!UTIL]. Exit Fast!UTIL Reboot System Return to Fast!UTIL End of procedure 22

23 Chapter 2 Setup Procedure for PRIMERGY > 2.2 Setup Procedure for the S26361-F3023-E1 Fibre Channel Card Installing the Drivers Refer to the documentation provided with each Fibre Channel card for details on how to obtain and install a Fibre Channel card driver for it Checking the Driver Version Use the Device Manager to check the version of the Fibre Channel card driver. Procedure 1 In the Device Manager go to [SCSI and RAID controllers], and open the [Properties] of the Fibre Channel card. 2 Select the [Driver] tab, and open the [Driver Details]. 3 Select the "ql2300.sys" driver file, and check its [File version]. If a different driver version is displayed from that shown in "Server Support Matrix", reinstall the driver. End of procedure Installing the ETERNUS Disk Storage System Driver Install the driver for ETERNUS Disk storage systems to the server if necessary. Refer to "Driver Notes" section in "ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for Windows " for notes on each driver. This section applies when using path redundancy control (path fail-over) for a multipath connected ETERNUS Disk storage system or when connecting the ETERNUS Disk storage system to the server via single-path. For details on how to install, uninstall, set up and operate the ETERNUS Disk storage systems' driver, refer to the Readme file or the User Guide provided with the software. 23

24 Chapter 3 Setup Procedure for PRIMEQUEST 1000 series 3.1 Setup Procedure for MC-0JFC11 and MC-0JFC21 Fibre Channel Cards Install the Fibre Channel cards in the server, and acquire their physical addresses and World Wide Names (WWNs). The physical address and WWN of a Fibre Channel card are required information in the following cases: when an error has occurred in the system, when using the ETERNUS Disk storage systems (security function, host affinity function, etc.) to restrict server access, or when connecting the ETERNUS Disk storage systems and the server using Fibre Channel switch. Acquire the physical address and WWN when installing the Fibre Channel card, because they cannot be determined from BIOS and OS. Physical address and WWN must be assigned to "WWN instance management table for the server". (1) Install the Fibre Channel card (2) Turn on the server If a SAN Boot environment is to be set up, the SAN Boot settings must be made beforehand for the PRIMEQUEST 1000 series. Refer to "Appendix D Configuration in the SAN Boot Environment" in "PRIMEQUEST 1000 series INSTALLATION MANUAL" for details. (3) Acquire the physical address and WWN for the Fibre Channel card (4) Add a record for the server in the WWN instance management table for the server When installing two or more Fibre Channel cards to the server, first turn off the server, then repeat Steps (1) through (4) above for each Fibre Channel card to be installed. 24

25 Chapter 3 Setup Procedure for PRIMEQUEST 1000 series > 3.1 Setup Procedure for MC-0JFC11 and MC-0JFC21 Fibre Channel Cards Installing the Fibre Channel Card For the installation method, position (PCI bus slots), and notes regarding the Fibre Channel card, refer to the Fibre Channel card documentation or the User Guide of the server. Procedure 1 Turn on the server, and press the [Alt] + [E] keys while the following message is displayed.!!! Emulex LPexxxx BIOS Copyright xxxx!!! xxxxxxxx Press <Alt E> to go to Emulex BIOS Utility. Press <s> to skip Emulex BIOS. "LightPulse BIOS Utility" starts. 2 Enter the number of the Fibre Channel card to be checked in [Enter a Selection:_] and press the [Enter] key. 3 Check the [I/O Base] and [Port Name] values. The value of [I/O Base] is the physical address and the value of [Port Name] is the Fibre Channel card WWN. Adapter 1: PCI Bus#:0x PCI Device#:0x Physical address LPexxxx: I/O Base: 5000 Firmware Version: xxxxxxxx Port Name: C938D229 Node Name: C938D229 Topology: Auto Topology: Loop first(default) Fibre Channel card WWN 1.Configure Boot Device 2.Configure This Adapter s Parameters Enter a Selection:_ Enter <x> to Exit <d> to Default Values <Page Up> to Previous Menu 4 Record the physical address and WWN in the WWN instance management table for the server (found in "Appendix A WWN Instance Management Table for the Server (Blank)" (page 30)). The following shows an example of this. Host name IP Address Physical slot name Fibre Channel card WWN Instance name Physical address slot C9 38 D Cable tag 25

26 Chapter 3 Setup Procedure for PRIMEQUEST 1000 series > 3.1 Setup Procedure for MC-0JFC11 and MC-0JFC21 Fibre Channel Cards Details of contents The details of contents for the WWN instance management table for the server are as follows: Host name: IP address: Physical slot name: Fibre Channel card WWN: Instance name: Physical address: Cable tag: Record the host name. Record the IP address of the server. Record the slot position of installed Fibre Channel card. For the installation location, refer to the User Guide for each server. Record the value of [Port Name] or [Adapter Port Name]. Not necessary to record. Record the value of [I/O Base] or [I/O Address]. Record a tag name which indicates the connection path (relationship between the connected device and the port). 5 Press the [x] key to exit "LightPulse BIOS Utility". When installing two or more Fibre Channel cards to the server, first turn off the server, then repeat Step 1 through Step 4 for each Fibre Channel card to be installed. If two or more Fibre Channel cards have already been installed in the server at the time of purchase, the one-to-one relationship between the WWNs and Fibre Channel cards may not be easy to determine. The correct WWPNs need to be registered and setup on the ETERNUS Disk storage system for a server to recognize the ETERNUS Disk storage system logical disks. If logical volumes are not recognized by a server, the WWPN maybe registered to an incorrect CM/CA Port. The WWN field on the WWN Registration maybe useful in identifying which Fibre Channel card is connected to which CM/CA Port. For most (but not all) configurations, the WWN field lists the WWNs of accessible HBAs. Refer to "ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) ETERNUS Disk Storage System Settings" for details about ETERNUS settings. End of procedure Installing the Drivers Refer to the documentation provided with each Fibre Channel card for details on how to obtain and install a Fibre Channel card driver for it. 26

27 Chapter 3 Setup Procedure for PRIMEQUEST 1000 series > 3.1 Setup Procedure for MC-0JFC11 and MC-0JFC21 Fibre Channel Cards Checking the Driver Version Use the Device Manager to check the version of the Fibre Channel card driver. Procedure 1 In the Device Manager go to [SCSI and RAID controllers], and open the [Properties] of the Fibre Channel card. 2 Select the [Driver] tab, and open the [Driver Details]. 3 Select the driver file (elxstor.sys), and check its [File version]. If a different driver version is displayed from that shown in "Server Support Matrix", reinstall the driver. End of procedure Setting up the Driver Parameters Use the application (OneCommand Manager, or other) provided by Emulex Corp. to set the driver parameters. This chapter describes the procedures using OneCommand Manager For the MC-0JFC11 and MC-0JFC21 Set the driver parameters after installing OneCommand Manager. When the server OS is Windows Server 2008 or Windows Server 2003, it is recommended that fixed Target IDs be assigned to the Fibre Channel card connected devices, and that automatic Target ID allocation be disabled. For details of the Target ID settings, refer to the "Fibre Channel Controller User's Guide". By default, Target IDs are automatically allocated. However, when a device is added, automatic Target ID allocation can result in a different distribution of Target IDs, which can cause the devices to not be recognized. Procedure 1 Install OneCommand Manager. For installation, refer to the Fibre Channel card documentation. 2 Start the OneCommand Manager. 27

28 Chapter 3 Setup Procedure for PRIMEQUEST 1000 series > 3.1 Setup Procedure for MC-0JFC11 and MC-0JFC21 Fibre Channel Cards 3 Select the target Fibre Channel card and click the [Driver Parameters] tab. When the same parameter values are to be set for all the Fibre Channel cards (common setting), select the target server instead of the target Fibre Channel card and click the [Driver Parameters] tab. 4 Check the parameter values in the [Adapter Parameter] list. Compare with the parameter values in the following tables, and correct the current value if necessary. Select the parameter whose value is to be corrected from the [Adapter Parameter] list and modify the value in the [Modify Adapter Parameter] area. - For Windows Server 2008/Windows Server 2003 Fibre Channel card Topology QueueDepth Value Queue Target LinkSpeed MC-0JFC11, MC-0JFC21 0 (FC-AL Connection) 1 (Fabric Connection) ETERNUS Calculated value (*1) ETERNUS4000, ETERNUS "254" 1 See the Link Speed settings table (*2), below *1: Use the following formula to calculate the proper setting value: Value = 40 / (No. of Server-side Fibre Channel ports connected to each ETERNUS-side CA port) (Round the result down) Use the value of "8" if the actual result is lower. *2: LinkSpeed settings: Fabric connection (Fibre Channel switch connection) FC-AL connection Fibre Channel card MC-0JFC11, MC-0JFC21 Maximum Fibre Channel switch link speed 8Gbps 4Gbps 2Gbps 1Gbps ETERNUS 2000 ETERNUS4000, ETERNUS8000 8Gbps FC-CA 4Gbps FC-CA Do not modify any parameters other than those described here. The following describes each parameter: - "Topology" parameter Set the connection type of the server and ETERNUS Disk storage systems. - "QueueDepth" parameter Set the command queue depth. - "QueueTarget" parameter Set to specify the command queue depth to either the LUN or to the target. - "LinkSpeed" parameter Set the LinkSpeed. 28

29 Chapter 3 Setup Procedure for PRIMEQUEST 1000 series > 3.1 Setup Procedure for MC-0JFC11 and MC-0JFC21 Fibre Channel Cards 5 After the values have been modified, click the [Apply] button. Values that have been modified but not yet applied are displayed in red in the [Value] column. Click the [Apply] button. 6 If there are multiple cards, repeat Step 2 through Step 4 to change the settings for all cards. 7 After all the cards have been set, select [Exit] from the [File] menu to quit the "OneCommand Manager". End of procedure Setting Fixed Target IDs (for Windows Server 2008 and Windows Server 2003) Each device connected to a Fibre Channel card is allocated a Target ID. By default, these Target IDs are automatically allocated by the driver. This means that, depending on the state of device recognition, the device Target IDs can and may be reallocated as devices are added and removed. If the Target IDs have changed when the server reboots, devices may end up off-line, and unavailable depending on the OS or application environment being used. Alternatively, automatic Target ID allocation can be disabled and the Fibre Channel card settings manually adjusted to assign an arbitrary Target ID to each device connected to the card. It is recommended that a fixed Target ID be allocated to each device in this way. Contact your supplier for more details Installing the ETERNUS Disk Storage System Driver Install the driver for ETERNUS Disk storage systems to the server if necessary. Refer to "Driver Notes" section in "ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for Windows " for notes on each driver. This section applies when using path redundancy control (path fail-over) for a multipath connected ETERNUS Disk storage system or when connecting the ETERNUS Disk storage system to the server via single-path. For details on how to install, uninstall, set up and operate the ETERNUS Disk storage systems' driver, refer to the Readme file or the User Guide provided with the software. 29

30 Appendix A WWN Instance Management Table for the Server (Blank) This table is used in "2.1.1 Installing the Fibre Channel Card" (page 10), "2.2.1 Installing the Fibre Channel Card" (page 19), and "3.1.1 Installing the Fibre Channel Card" (page 25), and should be used as necessary. WWN instance management table for the server Host name IP Address Physical slot name Fibre Channel card WWN Instance name Physical address Cable tag 30

31 ETERNUS Disk storage systems Server Connection Guide (Fibre Channel) for Windows Driver Settings for PRIMERGY/PRIMEQUEST 1000 Series Date of issuance: April 2010 Issuance responsibility: FUJITSU LIMITED The contents of this manual are liable to being updated without notice. While the contents of this manual are the product of all due care and diligence, no responsibility can be accepted for operational problems arising from any errors or missing information, or other use of the information contained in this manual. Fujitsu assumes no liability for damages to third party copyrights or other rights arising from the use of any information in this manual. Contents of this manual are not to be reproduced without permission from Fujitsu.

32