DPhy v1.2 Decoder MIPI 2.5Gb/s Protocol Decoder Hardware DataSheet & User Manual. January Rev 1.31

Transcription

1 DPhy v1.2 Decoder MIPI 2.5Gb/s Protocol Decoder Hardware DataSheet & User Manual January Rev 1.31

2 IMPORTANT SAFETY and USAGE INFORMATION Please review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it. To avoid potential hazards, use this product only as specified. Only The Moving Pixel Company should perform service procedures. Do not attempt service yourself. Return the unit to The Moving Pixel Company for service. While using this product, you may need to access other parts of a larger system. Read the safety sections of the other component manuals for warnings and cautions related to operating the system. To Avoid Fire or Personal Injury or Damage to Equipment Qualified Personnel to Operate this Product This manual and the product marking assumes that the user has more than basic electrical/electronic circuit knowledge and is a person comfortable by experience and education to safely connect probes to electrical circuits and systems. Do not operate this equipment nor connect it to any circuit or system if you are not qualified to do so by either education or experience. Use Proper Power Cord. Use only the power cord specified for this product and certified for the country of use. Use only the external power supply that is included with the product. Connect and Disconnect Properly. Do not connect or disconnect probes or test leads while they are connected to a voltage source. Ground the Product. This product is not inherently grounded through the grounding conductor of the power cord; it has a floating power supply. The negative lead of the power supply is directly connected to the metal shell of the unit and all SMA connections are also electrically connected to the metal shell of the unit. It is possible that improper connection to an external system could electrify the shell to potentially high voltages above ground. To avoid electric shock, the product must be tied to ground externally. Before making connections to the input or output terminals of the product, ensure that the product is properly grounded. Any markings, symbols, or textual references to ground, GND, and similar refer to the metal shell of the unit and assume that the metal shell is tied to a saftey ground externally.

3 Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings and markings on the product. Consult the product manual for further ratings information before making connections to the product. The inputs are not rated for connection to mains or Category II, III, or IV circuits. Connect the probe reference lead to earth ground only, no floating grounds allowed. Power Disconnect. The power cord disconnects the product from the power source. Do not block the power cord; it must remain accessible to the user at all times. Do Not Operate Without Covers. Do not operate this product with covers or panels removed. Do Not Operate With Suspected Failures. If you suspect that there is damage to this product, have it inspected by The Moving Pixel Company. Avoid Exposed Circuitry. Do not touch exposed connections and components when power is present. Do Not Operate in Wet/Damp Conditions. Do Not Operate in an Explosive Atmosphere. Keep Product Surfaces Clean and Dry. Provide Proper Ventilation. Refer to the manual s installation instructions for details on installing the product so it has proper ventilation. Symbols and Terms These terms may appear in this manual: WARNING. Warning statements identify conditions or practices that could result in injury or loss of life. CAUTION. Caution statements identify conditions or practices that could result in damage to this product or other property.

4 These terms may appear on the product: DANGER indicates an injury hazard immediately accessible as you read the marking. WARNING indicates an injury hazard not immediately accessible as you read the marking. CAUTION indicates a hazard to property including the product. The following symbol(s) may appear on the product:

5 Before Operating the Instrument Verify the ambient temperature: 5 C to +45 C. Verify the operating humidity: 8% to 80% relative humidity at up to +32 C 5% to 45% relative humidity above +32 C up to +45 C noncondensing, and is limited by a maximum wet-bulb temperature of +29 C (derates relative humidity to 32% at +45 C) Verify the operating altitude: 3,000 m, derate maximum operating temperature by 1 C per 300 meters above 1500 meters altitude. CAUTION. Operate in upright position only, keeping cooling holes on the sides of the unit clear of obstructions. Power Supply Requirements for the external power supply (provided): Source Voltage VAC Frequency Hz Power Consumption 70 W maximum It may be helpful to check our website for any updates to this documentation before you operate the instrument: If you have any questions at all about the warnings or operating conditions listed above: STOP! Do not operate the instrument. Contact The Moving Pixel Company and resolve your question before continuing. Contacting The Moving Pixel Company Phone US Pacific Time Zone (UTC-8) Fax Address Web site The Moving Pixel Company 4905 SW Griffith Drive, Suite 106 Beaverton, Oregon USA information@movingpixel.com

6 Declaration of Conformity The Moving Pixel Company declares that the DPhyDecoderV1.2 product conforms to the following Standards: EN/IEC :2013, Class A Radiated Emissions AS/NZS CISPR 11:2011 Class A Radiated Emissions FCC (g):2014 Class A Radiated Emissions FCC :2014 Class A Radiated Emissions ICES-003:2012 Class A Radiated Emissions VCCI: Class A Radiated Emissions EN/IEC :2013, Class A Conducted Emissions AS/NZS CISPR 11:2011 Class A Conducted Emissions FCC :2014 Class A Conducted Emissions ICES-003:2012 Class A Conducted Emissions VCCI: Class A Conducted Emissions EN :2013 Industrial in the following areas: IEC :2008 ESD immunity IEC :2010 RF electromagnetic field immunity IEC :2012 Electrical fast transient/burst immunity IEC :2005 Power line surge immunity IEC :2013 Conducted RF immunity IEC :2009 Magnetic Field immunity IEC :2004 Voltage dips and interruptions immunity Equipment type: Test and measurement equipment, indoor use only. Pollution Degree 2 as defined in IEC Rated for indoor use only. This product is intended for use in nonresidential areas only. Use in residential areas may cause electromagnetic interference. Emissions which exceed the levels required by this standard may occur when this equipment is connected to a test object. For compliance with the EMC standards listed here, high quality shielded interface cables that incorporate low impedance connection between the cable shield and the connector shell should be used.

7 Product end-of-life handling Observe the following guidelines when recycling an instrument or component: Equipment recycling. Production of this equipment required the extraction and use of natural resources. The equipment may contain substances that could be harmful to the environment or human health if improperly handled at the product s end of life. To avoid release of such substances into the environment and to reduce the use of natural resources, we encourage you to recycle this product in an appropriate system that will ensure that most of the materials are reused or recycled appropriately. This symbol indicates that this product complies with the applicable European Union requirements according to Directives 2012/19/EU and 2006/66/EC on waste electrical and electronic equipment (WEEE) and batteries. For information about recycling options, check the Support/Service section of the Tektronix Web site ( Restriction on Hazardous Substances Directive 2011/65/EU EN 50581:2012 Technical documentation for the assessment of electrical and electronic products with respect to the restrictions of hazardous substances. 7

8 MIPI DPhy Decoder 1.0 General: The MIPI DPhy v1.2 Decoder (DPhyDkd) is the hardware probe that supports MIPI DPhy signal acquisition with protocol decode occuring on a host Windows PC. Users familiar with the predecessor product DphyDecoder will note a nearly complete overlap of function and look and feel. The DPhyDkd supports: sophisticated real-time triggering Rx mode and Sniff mode real-time status monitoring activity statistics status LED indicators Sniff mode: active probes, solder-down, for minimal loading of the device under test. Rx mode includes internal active termination and SMA connectors USB 3.0 for fast data transfer The control and decode software that is provided with DPhyDkd (DPhyDecoderCtl) interfaces to the hardware and provides the following features: Configuration control Disassembly of the captured information in a logic analyzer-like format. Reassembly and display of any video information captured Storage of captured video frame(s) to a file(s). Refer to the DPhyDecoderCtl document for a detailed treatment of all the software features. DPhyDkd support up to 4 data lanes and 1 clock lane. Data rate operation up to 2.5 Gb/s per lane is supported. Connection to the DUT is via 5 active solder-down probes (supplied), one per lane or via SMA for Rx mode. Power for the DPhyDkd comes from an external desktop universal power supply. It also features a Trigger output on an SMA connector that can drive into a 50 ohm termination. Configuration and control and PC acquisition of the captured data from the DPhyDkd is via a USB 3.0 connection to the PC-based software application DPhyDecoderCtl. Refer to the DPhyDecoderCtl manual for the details of operating this software. 8

9 2.0 Requirements: The DPhyDkd must be connected to a PC via USB 2.0/USB3.0. The PC must be running the DphyDecoderCtl application and must have the drivers (provided) installed correctly. This will require Admin privelages on the PC. The PC must be running Microsoft Windows Win7-32/64 bit or Win 8/Win 10 The MIPI DPhy signals being monitored must be nearly within specification from both a protocol and an electrical point-of-view. This becomes more important as the link bitrate increases. 9

10 3 Connections and Indicators 3.1 USB The USB connection between the unit and the PC is made via the rear panel. The connector is labeled USB. It accepts the B end of a mini-usb 3.0 cable. The cable provided has enhanced retention features. 3.2 Power This is covered in the next section Usage. 3.3 Front Panel Indicator LEDs There are 8 front-panel indicators. Except as noted, they are sticky in that if an event occurs, the LED will light for a fixed period of time so that a human observer can see it happen. From left to right they are and indicate as follows: Idle Green. There is no traffic at the present time HSTraffic Green. There is High Speed traffic present. LP Traffic Green. There is Low Power traffic present. BTA Green. A Bus Turn Around cycle is in progress ULPS Green. Bus is in Ultra Low Power State. TriggerGreen. The trigger conditions specified via the GUI have been met. Errors Red, not sticky (the associated indicator in the GUI is sticky). CRC and/or Checksum errors have been detected. The reason this indicator is not sticky is so that a user can get a real-time feel for the error rate and feedback if the user is making an adjustment that may affect the error rate. Spare Yellow, this is reserved for future use. Currently it comes on at power up and stays on. 10

11 3.4 Probe heads In Sniff mode, signal acquisition from the DUT is via 5 active, solder-down probe heads: one for the clock lane and one each for up to 4 data lanes. Lanes are labeled at the Decoder end of the cable. For the highest electrical performance, we recommend a small whisker of wire be soldered between the probe tip end and the circuit under test. This will give the system some mechanical flexibility and will help prevent damage to either the probe tip ends or the circuit under test. Unused probe heads should be wrapped up in an antistatic container such as a nickel bag. If a user expects to not use particular lanes long-term, the probe head and cable can be unplugged and removed from inside the unit. Removal will keep the probe head out of the user s way and lessen the likelihood of damage (but remember where you put it; they are easy to lose and quite expensive to replace!). Probe polarity is identified in the following illustration. Probe + should connect to D-PHY lane Dp, with probe connecting to D-PHY Dn. If the input resistors to the probe become damaged as a result of soldering/de-soldering, etc., they may be replaced with 1.33 K 1% 0603 resistors. All normal soldering and ESD precautions must be observed. Probe head tip resistors are user-replaceable. 10 spare resistors are provided for each probe head. Users are cautioned that probe tip resistor soldering replacement requires a fair bit of skill in order to avoid damage to the probe head circuit board. CONNECTOR onback + - HEATSHRINK (color varies, clear shown) When soldering the probe directly to traces or pads or vias, care must be taken to prevent mechanical stress to the probe head else circuit damage may result. 11

12 The colors on the end of the probes are meaningless. They are provided to help with probe logistics. When shipped, Data Lane one is Red, Data Lane two is Green, Clock is Clear, Data Lane three is Blue, and Data Lane 4 is White (following the resistor color code). The probes are all interchangeable, including the clock. However, calibration will be slightly affected by interchanging the probes. For usage information, see section 4 below. 3.5 SMA inputs In Rx mode, signal acquisition from the DUT is via 10 SMA connectors: two for the differential clock lane and two for each differential lane for up to 4 data lanes. Lanes are labeled at the Decoder end of the cable. In Rx mode, these signals are actively terminated by the unit in response to the protocol on the wires. 12

13 4 Operation 4.1 Modes: There are two modes of operation: Sniff mode and Rx mode. Sniff mode acquires the signal from the DUT via the active solder-down probe heads. This is generally used mid-bus when there is a DPhy Transmitter connected to a DPhy receiver and the user wants to monitor and/or decode the traffic on the bus. The active probes non-invasively allow the user to monitor the traffic. The unit does not interact with either the transmitter or the receiver. 4.2 Connections: Sniff mode: Connect the USB cable to the PC, and the probe heads to the DUT. Make sure the black ground wire is attached to the DUT ground. We have found that the best way to connect the solder-down probes to the DUT is to solder short (~7mm) whisker wires to each of the probe tips then down to the DUT. Tie the probe head to the DUT with some electrical tape to stabilize the setup and strailrelieve the whisker wires. If short whisker wires cannot work for a particular setup, the user can extend the length to the probe head by soldering a ohm resistor to the DUT then extending the other end to the probe head. This wire can be up to ~40mm before significant signal degradation occurs. Note that this additional resistance will cause some degradation of the DPhy signal amplitude. In critical applications, the probe tip resistors value should be reduced by the amount of the additional external resistance Rx Mode: Connect the DUT transmitter to the SMA connections via high-quality 50 ohm coaxial cables. We recommend the length not exceed 70cm. The limitation is not due to the high-speed nature of the signal; it is due to MIPI DPhy LP mode not being terminated at the receiver and yet having fairly fast risetimes. Longer connections result in many reflections during LP signals. After about 90cm of length, the decoder may get confused by the reflections. In Rx mode, the unit actively terminates the signals as required by the protocol. Further, it will also respond (as programmed by the user via the DphyDecoderCtl GUI) to BTA requests as a normal receiver would. This response is rudimentary and the unit does not have the capability to respond differently to different types of BTA requests. 13

14 Connect the external 24 volt power supply to DPhyDkd via the connector on the rear panel marked 24 Vdc. Note that there is a LED visible through a hole next to the power connector. This LED will light with a green color when power is applied to the unit. Upon power-up, the left-most two leds ( Idle and HS Traffic ) will blink back and forth a few times to indicate that the internal boot process is complete. This system is intended to be operated in a lab environment where proper grounding of all equipment and surfaces is implemented. The system monitors very small signals across a very wide frequency range and is easily upset by large EM fields and static discharges. 14

15 4.3 Clock delay line setting The DPhyDkd was designed to operate with systems that may not be within spec, particularly with respect to the clock-to-data timing relationship. We have provided an adjustment available through the GUI so that a user can optimize the timing. As the user operates closer to the maximum clock rate limit for the DPhyDkd (the setting becomes more sensitive with number of lanes), this setting gets very critical, working over a ~400pS range typically at 1.5Gbps. A clue that the timing needs adjustment is that the DPhyDkd has no errors at lower frequencies. If it detects errors at the highest bit rates, the user should try changing this setting over a +/- 200pS range. The GUI has a button that automates the search for the best possible setting of this delay line. 4.4 Synchronization In MIPI DPhy v1.2 at bitrates greater than 1.5 Gbps, transmitters are required to send a training sequence periodically so that receivers can optimize their sampling phase. The DPhyDkd hardware has enough timing margin such that it does not actually need to train to recover the signal as long as it was transmitted within spec since the timing variation allowed in the spec is less than the acquisition setup and hold time required by the DPhyDkd. However, if the transmitter is out of spec, the signal can still be acquired by using the methods outlined in the paragraph above (4.3). 15

16 5.0 Electrical specification for the DPhyDecoder V1.2 Characteristic Specification Notes Maximum data rate 2.5 Gb/s per lane Maximum clock rate 1250 MHz Input Impedance, active probes Trigger Out, impedance Trigger Out, amplitude 2.0k to ground in parallel with less than 1pF, each side of the Differential input ~50 ohms ~3.3V open circuit 1.65V into 50 ohms This will slightly reduce the LP voltage high signal depending on the output impedance of the source Logic low is ground. Probe Head tip resistors 1.33k, 1% 0603 package style, lead-free Storage Capacity, video data 256MBytes 512Mbytes total vector storage (half is overhead). Clock delay range ~9 ns External Power Supply 24 Vdc, 50 watts max Universal, supplied Operating Environment degrees C Less than 15,000 elevation No condensing humidity Lab environment No strong, stray fields No static discharges Weight ~1170 grams approximate, without supply Weight, power supply and cord ~475 grams approximate Overall Dimensions 345mm x 195mm x 80mm Approximate, without supply Note that this product is RoHS compliant, even though it is currently exempt from RoHS requirements. 16

17 For more information contact: The Moving Pixel Company 4905 SW Griffith Drive Suite 106 Beaverton, Oregon phone PST 17