H3C S12500 Routing Switch Series GE Optical Ethernet Interface Card Datasheet

Transcription

1 H3C S12500 Routing Switch Series GE Optical Ethernet Interface Card Datasheet Copyright 2014 Hangzhou H3C Technologies Co., Ltd. All rights reserved. No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd. The information in this document is subject to change without notice.

2 Contents Overview 1 Key features 1 All-round maintenance and detection mechanisms 1 Environment-friendly design 1 Hot swapping 1 Specifications 2 LST1GP48LEB1 2 Technical specifications 2 LEDs 3 Transceiver modules 4 Environment requirements 5 Safety and regulatory compliance 6 EMC standards 6 i

3 Overview The H3C S12500 switches are core switching products designed by Hangzhou H3C Technologies Co., Ltd (hereinafter referred to as H3C) for next-generation data centers. The H3C S12500 switches adopt an advanced CLOS multi-level, multi-plane switching architecture, and provide various port densities and up to 100G access capability, meeting the requirements of data center application and future expansion. The S12500 switches provide the following types of GE optical Ethernet interface cards: Model Card type Description LST1GP48LEB1 EB 48-port GE optical Ethernet interface card LST1GP48LEC1 EC 48-port GE optical Ethernet interface card LST1GP48LEC2 EC 48-port GE optical Ethernet interface card LST1GP48LEF1 EF 48-port GE optical Ethernet interface card Key features All-round maintenance and detection mechanisms Online status detection mechanism The switch uses a dedicated maintenance engine to detect the device's switching fabric modules, backplane communication channel, service communication channel, key chips, and memory. Once a failure is detected, it will be reported to the system through the management bus. Card isolation function You can isolate a card from the forwarding plane. However, the card is still in the control plane, so you can perform management on the card, such as real-time diagnosis and CPLD upgrade, without affecting the system service. Environment-friendly design The S12500 switches implement intelligent power management through the intelligent EMS engine system. The S12500 switches support powering up cards in sequence, which helps reduce the shock to the power unit caused by simultaneously powering up the cards, expand the service lifetime of the device, and reduce the electromagnetic radiation. The switches also support powering off cards and separating failed/idle cards to reduce power consumption. The S12500 switches are compliant with the Restriction of Hazardous Substances (RoHS) of the European Union. Hot swapping GE optical Ethernet interface cards are hot swappable and support hot swapping of transceiver modules. 1

4 Specifications The LST1GP48LEB1, LST1GP48LEC1, LST1GP48LEC2, and LST1GP48LEF1 are similar in appearance except for the mark. This section uses the LST1GP48LEB1 as an example. LST1GP48LEB1 Figure 1 LST1GP48LEB1 NOTE: The card appearance is for illustration only. Technical specifications Item Boot ROM SDRAM Dimensions (H W D) Weight Power consumption Port type Specifications 2 MB 1 GB mm ( in) LST1GP48LEB1: 4.52 kg (9.96 lb) LST1GP48LEC1: 4.55 kg (10.03 lb) LST1GP48LEC2: 4.52 kg (9.96 lb) LST1GP48LEF1: 4.55 kg (10.03 lb) LST1GP48LEB1: 105 W to 170 W LST1GP48LEC1: 115 W to 180 W LST1GP48LEC2: 105 W to 170 W LST1GP48LEF1: 120 W to 195 W SFP/LC GE fiber port Port number 48 2

5 Item Port transmission speed Supported transceiver modules and maximum transmission distance Specifications 100/1000 Mbps For more information, see Table 3. NOTE: The S12500 requires type EC, type EB, or type EF cards based on operating modes. For more information about how to choose card types for different system operating modes, see H3C S12500 Series Routing Switches Fundamentals Configuration Guide. The LST1GP48LEC2 supports only Release 18xx and Release 73xx. LEDs Figure 2 Front panel of the LST1GP48LEB1 (1) (2) (3) (1) SFP/LC GE fiber ports (48 in total) (2) Port LED (3) RUN LED Table 1 Port LED description LED Status Description LINK/ACT Steady green Off Flashing green A link is present. No link is present. The port is sending or receiving data. Table 2 RUN LED description LED Status Description RUN Flashing green Flashing red Steady on Off The card is operating correctly. The card is faulty. The card is faulty. The card is faulty or out of position. 3

6 Transceiver modules Table 3 shows the supported SFP transceiver modules and their specifications. Table 3 GE SFP module specifications Model Central wavelength Connector Fiber Max. transmission distance GE SFP fiber modules SFP-GE-SX-MM8 50-A 850 nm LC 50/125 μm multi-mode 550 m ( ft) SFP-GE-SX-MM8 50-A 850 nm LC 62.5/125 μm multi-mode 275 m ( ft) SFP-GE-LX-SM13 10-A 10 km (6.21 miles) SFP-GE-LH40-S M km (24.86 miles) SFP-GE-LH40-S M nm LC 40 km (24.86 miles) M nm LC 70 km (43.49 miles) SFP-GE-LH100-S M nm LC 100 km (62.14 miles) GE BIDI modules SFP-GE-LX-SM13 10-BIDI RX: 1490 nm TX: 1310 nm LC 10 km (6.21 miles) SFP-GE-LX-SM14 90-BIDI RX: 1490 nm TX: 1310 nm LC 10 km (6.21 miles) GE CWDM modules M1470-CW 1470 nm LC M1490-CW 1490 nm LC M1510-CW 1510 nm LC M1530-CW 1530 nm LC M1550-CW 1550 nm LC M1570-CW 1570 nm LC M1590-CW 1590 nm LC M1610-CW 1610 nm LC 4

7 Model Central wavelength Connector Fiber Max. transmission distance FE/GE SFP modules (installed in a GE port to provide the port speed of 100 Mbps) SFP-FE-SX-MM1 310-GE 50/125 μm multi-mode 2 km (1.24 miles) SFP-FE-SX-MM1 310-GE 62.5/125 μm multi-mode 2 km (1.24 miles) FE/GE SFP module (installed in a GE port to provide the port speed of 100 Mbps or 1000 Mbps) SFP-GE/FE-LX10 -SM km (6.21 miles) GE SFP copper module SFP-GE-T N/A RJ-45 Category 5 or higher twisted pair cable 100 m ( ft) Environment requirements Table 4 Temperature and humidity Item Operating temperature Specification Long-term: 0 C to 40 C (32 F to 104 F) Short-term: 10 C to +50 C (14 F to 122 F) NOTE: Short-term operating hours: Continuous operation 96 hours Annual total operation 15 days Storage temperature 40 C to +70 C ( 40 F to +158 F) Relative humidity (noncondensing) 5% to 95% Table 5 Concentration limit of dust Mechanical active material Dust particles per m 3 Limit (No visible dust on the tabletop for three days) NOTE: Dust particle size 5 μm The equipment room must be protected against ingression of harmful gases such as SO 2, H 2 S, NO 2, NH 3, and Cl 2. For the specific requirement, see Table 6. 5

8 Table 6 Concentration limit of harmful gases Gas Average concentration (mg/m 3 ) Maximum concentration (mg/m 3 ) SO H 2 S NO NH Cl Safety and regulatory compliance EN (LVD Directive) IEC UL EMC standards AS/NZS CISPR22 Class A CISPR22 Class A CISPR24 EN55022 Class A EN55024 ETSI EN V1.3.3 FCC Part 15 (CFR 47) Class A GB 9254 Class A ICES-003 Class A IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN IEC/EN VCCI Class A 6