Manual name Manual No. Description. When installed to a PLC 2 (0.07) (1.57) (0.35) (1.03) (0.86) 28 (1.1) (0.55) 2.6(0.1) (1.25) 8 (0.31) 8 (0.

Transcription

1 ISPLA MOULE FXN5M USER S MANUAL J992490E This manual only describes the specifications for isplay Module FXN5M. For complete operation, wiring, mounting and programming instructions please refer to the FXS, FXN HARWARE MANUAL and PROGRAMMING MANUAL. These manuals should be read and understood before attempting to install or use the unit. Related s name No. escription FXS Series Hardware FXN Series Hardware FX Series Programming II J J99220 J9920 escribes contents related to hardware of FXS Series PL such as specifications, wiring and installation. (It is offered with FXS Series PL basic unit.) escribes contents related to hardware of FXN Series PL such as specifications, wiring and installation. (It is offered with FXN Series PL basic unit.) escribes instructions in FXS/FXN/FX2N/FX2N Series.. Outline of Product. Features The micro display module FXN5M (hereafter referred to as "5M") is mounted on the top face of the FXS/FXN Series PL basic unit and can monitor/update internal PL data. PLs installed to: FXS and FXN Series.2 Product configuration Main unit : FXN5M Accessories : Top cover for M, M3 screw to mount top cover.3 Outside dimensions 22 (0.6) 2 (.) 32 (.25) 4.6 (0.) When installed to a PL 2 40 (0.07) (.57) 9 26 (0.35) (.03) 36 (.4) 4 (0.55) 7.5 (0.29) 2.6(0.) 0 (0.39) (0.3) (0.3) (0.3) FXS Series FXN Series Note: These dimensions measured from the left side are common to the FXS and FXN Series. Unit: mm (inches) Outer painting color: Munsell 0.0G/7.64/0. Mass: 20 g (0.05 lbs).4 Name of each part ES key: ancels the last key operation or returns to the previous screen. "" key: Scrolls the device No. to a smaller one or decrements a numeric value by. "" key: Scrolls the device No. to a larger one or increments a numeric value. key: etermines the display device, executes write of a numeric value, or changes over forced setting and forced resetting. isplay area: isplays the current time and the monitored device status. onnector for PL 5M mounting hook

2 2. Installation Install the 5M to the PL using the following procedure. A) Top cover for M (offered as an accessory of 5M) B) onnector for optional equipment ) M3 screw to fix top cover Remove the top cover of the basic unit, and attach the top cover for M A) instead. Plug the 5M in to the connector B). If the 5M is always used, the top cover can be fixed with the M3 screw ). (Tightening torque: 0.3 to 0.6 N m) If the 5M is used together with a expansion board, remove and attach the 5M by pressing the 5M mounting hook provided at the bottom of the 5M. 3. Specifications 3. Environmental specifications The environmental specifications are equivalent to those of the PL main unit. (Refer to the handy manual offered with the FXS/FXN Series PL main unit.) 3.2 Power supply specifications The power is supplied from the PL main unit. 5V, 0 ma 4. Outline of Performance This section describes the list of the 5M. The operator s available with the operation keys of the 5M are described on the back of this manual. For the 5M control s available from the PL, refer to the FXS/FXN/FX2N/FX2N Series Programming. 4. list Symbols stand for the following. X: Input : Output M: Auxiliary relay S: State T: Timer : ounter : ata register : Butter memory of special units and special blocks Operator s: The operator can use these s by using only the operation keys of the 5M. Refer to the simplified chart of operations shown on the back face of this manual. escription lock isplay isplays current time of clock (built in FXS/FXN Series). Setting Allows to set time (year, month, day, hour and minute). evice Bit device monitor isplays ON/OFF status of X,, M and S. Word device (6bit) monitor isplays current and set values of T and and current value of. Word device (32bit) monitor isplays current and set values of 32bit and current value of. Buffer memory isplays buffer memory of special units and special blocks (offered only in FXN Series). Error display isplays error code and error occurrence step No. when a PL error has occurred. Forced set/reset Forces ON and OFF bit devices, M and S. T/ reset lears current value of T and (current value: 0, contact: OFF). ata change urrent value change hange current value of T, and. Set value change hange set value of T and. 5M control s: The 5M is controlled by sequence programs. For use of these s, refer to the FX Series Programming ΙΙ Protect Specified device Error display enable/disable Automatic backlight OFF Operation key status recognition escription Enables full use of all operator s, enables only monitor or enables only clock time display. Allows to specify device type and device No. to be displayed in 5M. Enables or disables error display (operator ). Allows to set automatic backlight OFF time (initial value: 0 min). Recognizes ON/OFF status of four operation keys.

3 autions: ) If a keyword to prohibit read, write or read and write of programs is registered in the PL, only the clock time display is available. Any other shown above is not available. If any operation is performed in the 5M when a keyword is registered in the PL, the error display flickers for 5 seconds. 2) The automatic backlight OFF is set to 0 minutes as the initial value. As far as the OFF time is not changed by a sequence program, the backlight turns off 0 minutes later. If any key is pressed after the backlight turns off, the contents displayed just before the backlight turns off appear again. A key pressed for the first time after the backlight turns off is regarded as a trigger to turn on the backlight, and is not regarded as a key operation. 4.2 ontrol devices for 5M When using the 5M control, specify data registers () and auxiliary relays (M) used to control the 5M to special data registers 5 and 59. Five data registers and 5 auxiliary relays are occupied for control of the 5M. For the control device use procedure, refer to the FXS/FXN/FX2N/FX2N Series Programming. Special ontrol device escription Application 5 K 59 K evice type to be displayed * For specified device evice No. to be displayed 2 Backlight OFF time (min) OFF 3 Protects display screen. *2 For protect 4 M Requests edition of displayed device data. For specified device M Edition completion response M2 isables backlight OFF. (Turns on backlight forcedly.) OFF M3 isplays or hides operation errors, etc. *3 Others M4 ES key status *4 M5 "" key status *4 For specified device M6 "" key status *4 M7 key status *4 M M9 M0 M M2 M3 M4 * Input numeric values correspond to the devices as follows. : Input (X) 2: Output () 3: Auxiliary relay (M) 4: State (S) 5: Timer (T) 6: ounter (), 6bit (current value/set value) and 32bit (set value) 7: ata register (), 6bit: ata register (), 32bit 9: Time display 0: ounter (), 6bit (current value/set value) and 32bit (current value) *2 0: Enables all operations. : Enables only the time display. 2: Enables only the. *3 P hardware errors, parameter errors, grammatical errors and circuit errors are unconditionally displayed. While this bit is ON, I/O configuration errors, parallel link errors and operation errors are also displayed. *4 Every operation key is the momentary type, and s as follows: While a key is pressed and held: ON While key is not pressed: OFF 4.3 escription on display area The display area of the 5M shows the following. "": isplayed while the PL is running, and not displayed while the PL is stopped. ON R T ➈ "": isplays the contents of the buffer memory when a special block is connected (only in the FXN Series). "ON/OFF": isplayed while T or is ON in the word device monitor, and not displayed while T or is OFF. "R" (reset): isplayed while T or is reset. "" (32bit): isplayed when a 32bit is specified. evice type: isplays the device type (T,,, X,, M or S) currently being displayed. evice No.: isplays the device No. currently being displayed. urrent value: isplays the current value of T, or. ➈ Set value: isplays the set value of T or. * In the case of 32bit or, upper 5 digits are displayed in and the lower 5 digits are displayed in ➈.

4 5. Operation List The process for the operator s are shown below. The operation keys are expressed as follows. ES : ES key : "" key : "" key : key Time display screen (when the power is turned on) <Setting the time> Press and hold it for 2 seconds or more. <Selecting a device> Program error Keyword error (Entry code error) ( E r r o r d i s p l a y ) Refer to error display. T etermine An item being changed flickers. Set "year, month, day, hour and minute" in this order. When the key is pressed at "minute" set up, the setting operation will be completed. etermine Select an either device using the "" and "" keys. (In the initial status, "" flickers.) T,, (6bit), (32bit), X,, M, S or "" key "" key * "" is displayed only when the FXN Series PL is used. To <Monitoring a bit device (X//M/S)> <Forced setting/resetting a bit device (/M/S)> Set or reset the bit device. From the displayed device No., the ON/OFF status of points (in the case of X or ) or 0 points (in the case of M or S) is indicated. : OFF status : ON status Eight points (in the case of X or ) or 0 points (in the case of M or S) are scrolled at a time. "" key: Scrolls toward larger device Nos. " " key: Scrolls toward smaller device Nos. Forced set/reset mode A selected device is indicated with underline. Underline flickers. Select a device No. The current ON/OFF status is reversed. * The device turns on and off alternately when the key is pressed. If the key is pressed while the device is ON, it turns off. If the key is pressed while the device is OFF, it turns on. < unit selection> S: State T: Timer <Buffer memory No. selection> <Buffer memory change> Press and hold for 2 sec or more. If a special block is connected to the FXN Series when you select a device, a buffer memory (hereafter referred to as "") is displayed. A displayed numeric value indicates the unit No. When you press the key, monitor starts for the unit having the displayed unit No. The No. is displayed. The current value is displayed. Select the No. After pressing the key, you can change the value of the displayed No. Every time you press and hold the key for 2 seconds or more, the display changes over alternately between 6bit and 32bit. Increase or decrease the current value using the "" or "" key. Write the data you have input to the. AUTION epending on the type of the connected special block, the is cleared when the power is turned off or the mode is changed over between and STOP. When using a special unit, write the data finally to the using a sequence program (using FN 79 TO instruction (write to ).) Guidelines for the safety of the user and protection of the Micro isplay Module FXN5M This manual has been written to be used by trained and competent personnel. This is defined by the European directives for machinery, low voltage and EM. If in doubt at any stage during the installation of the Micro isplay Module FXN5M always consult a professional electrical engineer who is qualified and trained to the local and national standards. If in doubt about the operation or use of the Micro isplay Module FXN5M please consult the nearest Mitsubishi Electric distributor. Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment. All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples. Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application.

5 <Monitoring 6bit T or 6bit > <hanging the current value/set value of 6bit T or 6bit > T hanging the etermine current value <Resetting the current value> hanging the set value Press and hold it for "ON" is displayed when T or is ON and "R" is displayed while resetting. hange over the device to monitor. T or that is not used in the program is not displayed. (A horizontal line "" is displayed if there is none of T or in the program.) When the key is pressed once, the current value is changed, and when the key is pressed three times, the set value is changed. (Flickers while changing) Press the "" key to increase the value. Press the "" key to decrease the value. Press the key to determine At this time, the input data is written to the PL. When the key is pressed and held for 2 seconds or more while the current value is changed, the current value is reset to "0" and the contact turns off. When the key is pressed once again, the current value reset operation will be completed. <Monitoring 32bit > urrent value <hanging the current set value of 32bit > etermine <Resetting the current value> Press and hold it for S Set value Press the "" or "" key to change over the current value and the set value. For the set value, "S" is added in a right position above the device No. When the key is pressed, the current value or the set value is changed. Press the "" key to increase the value. Press the "" key to decrease the value. Press the key to determine At this time, the input data is written to the PL. When the key is pressed and held for 2 seconds or more while the current value is changed, the current value is reset to "0" and the contact turns off. When the key is pressed once again, the current value reset operation will be completed. <Monitoring 6bit > <hanging the current value of 6bit > is scrolled by point at a time. Select the current value change mode. Press the "" key to increase the value. Press the "" key to decrease the value. Press the key to determine At this time, the input data is written to the PL. <Monitoring 32bit > <hanging the current value of 32bit > is scrolled by 2 points at a time by the "" key and by point at a time by the "" key. Select the current value change mode. Press the "" key to increase the value. Press the "" key to decrease the value. Press the key to determine At this time, the input data is written to the PL. <Error display> Error step No. Error code Press the ES key or release the error status to delete the error display. <Keyword (Entry code) error display> When an keyword (entry code) has been input to the PL, only the time can be displayed. If you press the key while the time is displayed, the error message shown on the left flickers for 5 seconds. Release the keyword (entry code) in a peripheral unit such as the FX0P/20P and the personal computer software for creating sequence programs. number : J revision : E ate : June 200 This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric orporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual. HEA OFFIE : TO BUILING, 273 MAOUHI, HIOAKU, TO 0030 JAPAN HIMEJI WORKS : 40, HIOA HO, HIMEJI, JAPAN J992490E Effective June 200 Specifications are subject to change without notice

6 ISPLA MOULE FXN5M USER S MANUAL J992490E This manual only describes the specifications for isplay Module FXN5M. For complete operation, wiring, mounting and programming instructions please refer to the FXS, FXN HARWARE MANUAL and PROGRAMMING MANUAL. These manuals should be read and understood before attempting to install or use the unit. Related s name No. escription FXS Series Hardware FXN Series Hardware FX Series Programming II. Outline of Product. Features The micro display module FXN5M (hereafter referred to as "5M") is mounted on the top face of the FXS/FXN Series PL basic unit and can monitor/update internal PL data. PLs installed to: FXS and FXN Series.2 Product configuration Main unit : FXN5M Accessories : Top cover for M, M3 screw to mount top cover.3 Outside dimensions.4 Name of each part J J99220 J (0.6) 2 (.) 32 (.25) 4.6 (0.) 36 (.4) escribes contents related to hardware of FXS Series PL such as specifications, wiring and installation. (It is offered with FXS Series PL basic unit.) escribes contents related to hardware of FXN Series PL such as specifications, wiring and installation. (It is offered with FXN Series PL basic unit.) escribes instructions in FXS/FXN/FX2N/FX2N Series. When installed to a PL 2 40 (0.07) (.57) 9 26 (0.35) (.03) 4 (0.55) 7.5 (0.29) 2.6(0.) 0 (0.39) (0.3) (0.3) (0.3) FXS Series FXN Series ES key: ancels the last key operation or returns to the previous screen. "" key: Scrolls the device No. to a smaller one or decrements a numeric value by. "" key: Scrolls the device No. to a larger one or increments a numeric value. key: etermines the display device, executes write of a numeric value, or changes over forced setting and forced resetting. isplay area: isplays the current time and the monitored device status. onnector for PL 5M mounting hook Note: These dimensions measured from the left side are common to the FXS and FXN Series. Unit: mm (inches) Outer painting color: Munsell 0.0G/7.64/0. Mass: 20 g (0.05 lbs) 2. Installation Install the 5M to the PL using the following procedure. A) Top cover for M (offered as an accessory of 5M) B) onnector for optional equipment ) M3 screw to fix top cover Remove the top cover of the basic unit, and attach the top cover for M A) instead. Plug the 5M in to the connector B). If the 5M is always used, the top cover can be fixed with the M3 screw ). (Tightening torque: 0.3 to 0.6 N m) If the 5M is used together with a expansion board, remove and attach the 5M by pressing the 5M mounting hook provided at the bottom of the 5M. 3. Specifications 3. Environmental specifications The environmental specifications are equivalent to those of the PL main unit. (Refer to the handy manual offered with the FXS/FXN Series PL main unit.) 3.2 Power supply specifications The power is supplied from the PL main unit. 5V, 0 ma 4. Outline of Performance This section describes the list of the 5M. The operator s available with the operation keys of the 5M are described on the back of this manual. For the 5M control s available from the PL, refer to the FXS/FXN/FX2N/FX2N Series Programming. 4. list Symbols stand for the following. X: Input : Output M: Auxiliary relay S: State T: Timer : ounter : ata register : Butter memory of special units and special blocks Operator s: The operator can use these s by using only the operation keys of the 5M. Refer to the simplified chart of operations shown on the back face of this manual. escription lock isplay isplays current time of clock (built in FXS/FXN Series). Setting Allows to set time (year, month, day, hour and minute). evice Bit device monitor isplays ON/OFF status of X,, M and S. Word device (6bit) monitor isplays current and set values of T and and current value of. Word device (32bit) monitor isplays current and set values of 32bit and current value of. Buffer memory isplays buffer memory of special units and special blocks (offered only in FXN Series). Error display isplays error code and error occurrence step No. when a PL error has occurred. Forced set/reset Forces ON and OFF bit devices, M and S. T/ reset lears current value of T and (current value: 0, contact: OFF). ata change urrent value change hange current value of T, and. Set value change hange set value of T and. 5M control s: The 5M is controlled by sequence programs. For use of these s, refer to the FX Series Programming ΙΙ Protect Specified device Error display enable/disable Automatic backlight OFF Operation key status recognition escription Enables full use of all operator s, enables only monitor or enables only clock time display. Allows to specify device type and device No. to be displayed in 5M. Enables or disables error display (operator ). Allows to set automatic backlight OFF time (initial value: 0 min). Recognizes ON/OFF status of four operation keys. autions: ) If a keyword to prohibit read, write or read and write of programs is registered in the PL, only the clock time display is available. Any other shown above is not available. If any operation is performed in the 5M when a keyword is registered in the PL, the error display flickers for 5 seconds. 2) The automatic backlight OFF is set to 0 minutes as the initial value. As far as the OFF time is not changed by a sequence program, the backlight turns off 0 minutes later. If any key is pressed after the backlight turns off, the contents displayed just before the backlight turns off appear again. A key pressed for the first time after the backlight turns off is regarded as a trigger to turn on the backlight, and is not regarded as a key operation. 4.2 ontrol devices for 5M When using the 5M control, specify data registers () and auxiliary relays (M) used to control the 5M to special data registers 5 and 59. Five data registers and 5 auxiliary relays are occupied for control of the 5M. For the control device use procedure, refer to the FXS/FXN/FX2N/FX2N Series Programming. Special ontrol device escription Application 5 K 59 K evice type to be displayed * For specified device evice No. to be displayed 2 Backlight OFF time (min) OFF 3 Protects display screen. *2 For protect 4 M Requests edition of displayed device data. For specified device M Edition completion response M2 isables backlight OFF. (Turns on backlight forcedly.) OFF M3 isplays or hides operation errors, etc. *3 Others M4 ES key status *4 M5 "" key status *4 For specified device M6 "" key status *4 M7 key status *4 M M9 M0 M M2 M3 M4 * Input numeric values correspond to the devices as follows. : Input (X) 2: Output () 3: Auxiliary relay (M) 4: State (S) 5: Timer (T) 6: ounter (), 6bit (current value/set value) and 32bit (set value) 7: ata register (), 6bit: ata register (), 32bit 9: Time display 0: ounter (), 6bit (current value/set value) and 32bit (current value) *2 0: Enables all operations. : Enables only the time display. 2: Enables only the. *3 P hardware errors, parameter errors, grammatical errors and circuit errors are unconditionally displayed. While this bit is ON, I/O configuration errors, parallel link errors and operation errors are also displayed. *4 Every operation key is the momentary type, and s as follows: While a key is pressed and held: ON While key is not pressed: OFF 4.3 escription on display area The display area of the 5M shows the following. "": isplayed while the PL is running, and not displayed while the PL is stopped. ON R T ➈ "": isplays the contents of the buffer memory when a special block is connected (only in the FXN Series). "ON/OFF": isplayed while T or is ON in the word device monitor, and not displayed while T or is OFF. "R" (reset): isplayed while T or is reset. "" (32bit): isplayed when a 32bit is specified. evice type: isplays the device type (T,,, X,, M or S) currently being displayed. evice No.: isplays the device No. currently being displayed. urrent value: isplays the current value of T, or. ➈ Set value: isplays the set value of T or. * In the case of 32bit or, upper 5 digits are displayed in and the lower 5 digits are displayed in ➈.

7 5. Operation List The process for the operator s are shown below. The operation keys are expressed as follows. ES : ES key : "" key : "" key : key Time display screen (when the power is turned on) <Setting the time> Press and hold it for 2 seconds or more. <Selecting a device> Program error Keyword error (Entry code error) ( E r r o r d i s p l a y ) Refer to error display. <Monitoring a bit device (X//M/S)> From the displayed device No., the ON/OFF status of points (in the case of X or ) or 0 points (in the case of M or S) is indicated. : OFF status : ON status Eight points (in the case of X or ) or 0 points (in the case of M or S) are scrolled at a time. "" key: Scrolls toward larger device Nos. " " key: Scrolls toward smaller device Nos. T etermine An item being changed flickers. Set "year, month, day, hour and minute" in this order. When the key is pressed at "minute" set up, the setting operation will be completed. etermine Select an either device using the "" and "" keys. (In the initial status, "" flickers.) T,, (6bit), (32bit), X,, M, S or "" key "" key * "" is displayed only when the FXN Series PL is used. <Forced setting/resetting a bit device (/M/S)> Forced set/reset mode A selected device is indicated with underline. Underline flickers. To Select a device No. Set or reset the bit device. The current ON/OFF status is reversed. * The device turns on and off alternately when the key is pressed. If the key is pressed while the device is ON, it turns off. If the key is pressed while the device is OFF, it turns on. <Monitoring 6bit T or 6bit > <hanging the current value/set value of 6bit T or 6bit > T hanging the etermine current value <Resetting the current value> hanging the set value Press and hold it for "ON" is displayed when T or is ON and "R" is displayed while resetting. hange over the device to monitor. T or that is not used in the program is not displayed. (A horizontal line "" is displayed if there is none of T or in the program.) When the key is pressed once, the current value is changed, and when the key is pressed three times, the set value is changed. (Flickers while changing) Press the "" key to increase the value. Press the "" key to decrease the value. Press the key to determine At this time, the input data is written to the PL. When the key is pressed and held for 2 seconds or more while the current value is changed, the current value is reset to "0" and the contact turns off. When the key is pressed once again, the current value reset operation will be completed. <Monitoring 32bit > urrent value S Set value <hanging the current set value of 32bit > etermine <Resetting the current value> Press and hold it for Press the "" or "" key to change over the current value and the set value. For the set value, "S" is added in a right position above the device No. When the key is pressed, the current value or the set value is changed. Press the "" key to increase the value. Press the "" key to decrease the value. Press the key to determine At this time, the input data is written to the PL. When the key is pressed and held for 2 seconds or more while the current value is changed, the current value is reset to "0" and the contact turns off. When the key is pressed once again, the current value reset operation will be completed. <Monitoring 6bit > <hanging the current value of 6bit > is scrolled by point at a time. Select the current value change mode. Press the "" key to increase the value. Press the "" key to decrease the value. Press the key to determine At this time, the input data is written to the PL. < unit selection> S: State T: Timer <Buffer memory No. selection> <Buffer memory change> Press and hold for 2 sec or more. If a special block is connected to the FXN Series when you select a device, a buffer memory (hereafter referred to as "") is displayed. A displayed numeric value indicates the unit No. When you press the key, monitor starts for the unit having the displayed unit No. The No. is displayed. The current value is displayed. Select the No. After pressing the key, you can change the value of the displayed No. Every time you press and hold the key for 2 seconds or more, the display changes over alternately between 6bit and 32bit. Increase or decrease the current value using the "" or "" key. Write the data you have input to the. AUTION epending on the type of the connected special block, the is cleared when the power is turned off or the mode is changed over between and STOP. When using a special unit, write the data finally to the using a sequence program (using FN 79 TO instruction (write to ).) <Error display> <Monitoring 32bit > is scrolled by 2 points at a time by the "" key and by point at a time by the "" key. Select the current value change mode. Press the "" key to increase the value. Press the "" key to decrease the value. Press the key to determine At this time, the input data is written to the PL. Error step No. Error code Press the ES key or release the error status to delete the error display. <hanging the current value of 32bit > <Keyword (Entry code) error display> When an keyword (entry code) has been input to the PL, only the time can be displayed. If you press the key while the time is displayed, the error message shown on the left flickers for 5 seconds. Release the keyword (entry code) in a peripheral unit such as the FX0P/20P and the personal computer software for creating sequence programs. number : J revision : E ate : June 200 Guidelines for the safety of the user and protection of the Micro isplay Module FXN5M This manual has been written to be used by trained and competent personnel. This is defined by the European directives for machinery, low voltage and EM. If in doubt at any stage during the installation of the Micro isplay Module FXN5M always consult a professional electrical engineer who is qualified and trained to the local and national standards. If in doubt about the operation or use of the Micro isplay Module FXN5M please consult the nearest Mitsubishi Electric distributor. Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment. All examples and diagrams shown in this manual are intended only as an aid to understanding the text, not to guarantee operation. Mitsubishi Electric will accept no responsibility for actual use of the product based on these illustrative examples. Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application. This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric orporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual. HEA OFFIE : TO BUILING, 273 MAOUHI, HIOAKU, TO 0030 JAPAN HIMEJI WORKS : 40, HIOA HO, HIMEJI, JAPAN J992490E Effective June 200 Specifications are subject to change without notice